The historical and future storm surge climate over the South China Sea Sunda Shelf was derived using a barotropic two dimensional model. The atmospheric forcings were obtained from the UKMO regional climate modeling system, PRECIS (Providing Regional Climates for Impacts Studies), forced at the boundary by the ECHAM4 simulation output under the SRES A2 emission experiment. In general, the model simulates historical sea surface elevation characteristics satisfactory although there is a substantial underestimation for the sea level elevation at local scales. The climate change analysis suggests that the storm surge extreme over the Sunda Shelf is expected to increase along the coastal area of the Gulf of Thailand and east coast of Peninsular Malaysia in the future (2071-2100). The projected increment is averagely ~9% over the Sunda Shelf region by the end of the 21st century corresponding to about 5% stronger wind speed as compare to the baseline period of 1961-1990.
This research mainly focused on isolation of non-starch polysaccharide (NSP) from different parts of cassava tuber by using water extraction and to evaluate the effect of NSP addition into flour on nutritional composition, swelling and solubility, pasting properties and dough characteristics by farinograph and extensograph. Three origins of (NSP) extracted were used: cassava peels, coarse and fine portions from cassava flesh. The isolation of NSP was done by using water extraction method and designated as water-extractable (WEP) and water un-extractable non starch polysaccharides (WUP). The percentage yield of WEP (0.24 - 1.64%) from water extraction was significantly lower as compared to WUP (2.58 - 4.33%). Upon the incorporation of 5% NSP, the cassava flour showed lower moisture content compared to the sample without the addition of NSP, while fats and crude fiber content of cassava flours were found to be increased upon the incorporation of 5% NSP from all origins. Swelling power and solubility of cassava flour were being reduced upon the incorporation of 5% of NSP from cassava peel and coarse portion of cassava flesh. The changes in dough characteristics showed that water absorption of the samples upon the addition of 5% NSP into wheat flour was found to be higher compared to control wheat flour. In contrast, dough stability and extensibility, tolerance index, resistance to extension, as well as the work input necessary for dough deformation from wheat flour with addition of 5% NSP resulted lower than control wheat flour. Overall, NSP extracted from cassava peels and coarse portion of cassava flesh performed similar characteristics and functional properties upon the incorporation into the flour.
This paper investigates the field-dependent rheological properties of magnetorheological (MR) fluid used to fill in MR dampers after long-term cyclic operation. For testing purposes, a meandering MR valve was customized to create a double-ended MR damper in which MR fluid flowed inside the valve due to the magnetic flux density. The test was conducted for 170,000 cycles using a fatigue dynamic testing machine which has 20 mm of stroke length and 0.4 Hz of frequency. Firstly, the damping force was investigated as the number of operating cycles increased. Secondly, the change in viscosity of the MR fluid was identified as in-use thickening (IUT). Finally, the morphological observation of MR particles was undertaken before and after the long-term operation. From these tests, it was demonstrated that the damping force increased as the number of operating cycles increases, both when the damper is turn on (on-state) and off (off-state). It is also observed that the particle size and shape changed due to the long operation, showing irregular particles.
We have decomposed to symmetric and asymmetric modes the mass-TKE fission fragment distributions calculated by 4-dimensional Langevin approach and observed how the dominant fission mode and symmetric mode change as functions of [Formula: see text] of the fissioning system in the actinides and trans-actinide region. As a result, we found that the symmetric mode makes a sudden transition from super-long to super short fission mode around 254Es. The dominant fission modes on the other hand, are persistently asymmetric except for 258Fm, 259Fm and 260Md when the dominant fission mode suddenly becomes symmetric although it returns to the asymmetric mode around 256No. These correlated "twin transitions" have been known empirically by Darleane Hoffman and her group back in 1989, but for the first time we have given a clear explanation in terms of a dynamical model of nuclear fission. More specifically, since we kept the shape model parameters unchanged over the entire mass region, we conclude that the correlated twin transition emerge naturally from the dynamics in 4-D potential energy surface.
Conventional thermal fluids with suspended nanoparticles, known as nanofluids, have been developed for heat transfer applications. Heat transfer loss could be reduced significantly if the thermophysical properties of the heat transfer fluid are improved, which to some extent, could reduce the present global environmental challenges associated with energy utilization, such as climate change and global warming. In this work, the role of the concentration of sodium dodecyl-benzene sulfonate (SDBS) in the stability of Al₂O₃/bio-oil nanofluid is investigated the zeta potential value, and its implications to the viscosity and thermal conductivity of the nanofluid are explored. The bio-oil based nanofluid is fixed using a two-step method in which the prepared base fluid is added with 13-nm alumina nanoparticles powder. Various weight fractions of SDBS (0.1, 0.2, 0.4, 0.6, and 1.0 wt%) are used for both 0.1 and 0.2 wt% Al₂O₃ to investigate the significance of the stability of a nanofluid on its thermal conductivity and viscosity. Results indicate that a stable nanofluid has reduced viscosity and increased thermal conductivity.
Resource bound security solutions have facilitated the mitigation of spatio-temporal attacks by altering protocol semantics to provide minimal security while maintaining an acceptable level of performance. The Dynamic Window Secured Implicit Geographic Forwarding (DWSIGF) routing protocol for Wireless Sensor Network (WSN) has been proposed to achieve a minimal selection of malicious nodes by introducing a dynamic collection window period to the protocol's semantics. However, its selection scheme suffers substantial packet losses due to the utilization of a single distance based parameter for node selection. In this paper, we propose a Fuzzy-based Geographic Forwarding protocol (FuGeF) to minimize packet loss, while maintaining performance. The FuGeF utilizes a new form of dynamism and introduces three selection parameters: remaining energy, connectivity cost, and progressive distance, as well as a Fuzzy Logic System (FLS) for node selection. These introduced mechanisms ensure the appropriate selection of a non-malicious node. Extensive simulation experiments have been conducted to evaluate the performance of the proposed FuGeF protocol as compared to DWSIGF variants. The simulation results show that the proposed FuGeF outperforms the two DWSIGF variants (DWSIGF-P and DWSIGF-R) in terms of packet delivery.
Plasmonic antennas are attractive optical components of the optoelectronic devices, operating in the far-infrared regime for sensing and imaging applications. However, low optical absorption hinders its potential applications, and their performance is limited due to fixed resonance frequency. In this article, a novel gate tunable graphene-metal hybrid plasmonic antenna with stacking configuration is proposed and investigated to achieve tunable performance over a broad range of frequencies with enhanced absorption characteristics. The hybrid graphene-metal antenna geometry is built up with a hexagon radiator that is supported by the Al2O3 insulator layer and graphene reflector. This stacked structure is deposited in the high resistive Si wafer substrate, and the hexagon radiator itself is a sandwich structure, which is composed of gold hexagon structure and two multilayer graphene stacks. The proposed antenna characteristics i.e., tunability of frequency, the efficiency corresponding to characteristics modes, and the tuning of absorption spectra, are evaluated by full-wave numerical simulations. Besides, the unity absorption peak that was realized through the proposed geometry is sensitive to the incident angle of TM-polarized incidence waves, which can flexibly shift the maxima of the absorption peak from 30 THz to 34 THz. Finally, an equivalent resonant circuit model for the investigated antenna based on the simulations results is designed to validate the antenna performance. Parametric analysis of the proposed antenna is carried out through altering the geometric parameters and graphene parameters in the Computer Simulation Technology (CST) studio. This clearly shows that the proposed antenna has a resonance frequency at 33 THz when the graphene sheet Fermi energy is increased to 0.3 eV by applying electrostatic gate voltage. The good agreement of the simulation and equivalent circuit model results makes the graphene-metal antenna suitable for the realization of far-infrared sensing and imaging device containing graphene antenna with enhanced performance.
Unsteady mixed convection flow of Casson fluid towards a nonlinearly stretching sheet with the slip and convective boundary conditions is analyzed in this work. The effects of Soret Dufour, viscous dissipation and heat generation/absorption are also investigated. After using some suitable transformations, the unsteady nonlinear problem is solved by using Keller-box method. Numerical solutions for wall shear stress and high temperature transfer rate are calculated and compared with previously published work, an excellent arrangement is followed. It is noticed that fluid velocity reduces for both local unsteadiness and Casson parameters. It is likewise noticed that the influence of a Dufour number of dimensionless temperature is more prominent as compared to species concentration. Furthermore, the temperature was found to be increased in the case of nonlinear thermal radiation.
Recently, global interest in organizing the functioning of renewable energy resources (RES) through microgrids (MG) has developed, as a unique approach to tackle technical, economic, and environmental difficulties. This study proposes implementing a developed Distributable Resource Management strategy (DRMS) in hybrid Microgrid systems to reduce total net percent cost (TNPC), energy loss (Ploss), and gas emissions (GEM) while taking the cost-benefit index (CBI) and loss of power supply probability (LPSP) as operational constraints. Grey Wolf Optimizer (GWO) was utilized to find the optimal size of the hybrid Microgrid components and calculate the multi-objective function with and without the proposed management method. In addition, a detailed sensitivity analysis of numerous economic and technological parameters was performed to assess system performance. The proposed strategy reduced the system's total net present cost, power loss, and emissions by (1.06%), (8.69%), and (17.19%), respectively compared to normal operation. Firefly Algorithm (FA) and Particle Swarm Optimization (PSO) techniques were used to verify the results. This study gives a more detailed plan for evaluating the effectiveness of hybrid Microgrid systems from a technical, economic, and environmental perspective.
This article aims to discuss (1) the incorrect identification of Cr(III) and Cr(VI) binding energies in the Cr 2p XPS (X-ray photoelectron spectroscopy) spectra of the laden adsorbent (the nZVI-BC sample after Cr(VI) adsorption), (2) misconception regarding the Weber-Morris intraparticle diffusion model, and (3) inconsistency between the experiential data and the Thomas adsorption rate constants. The authors hope that our comments are beneficial for other researchers to avoid the undesirable mistakes.
Pre-stressing is a concept used in many engineering structures. In this study prestressing in the form of axial compression stress is proposed in the blade structure of H-Darrieus wind turbine. The study draws a structural comparison between reference and prestressed configurations of turbine rotor with respect to their dynamic vibrational response. Rotordynamics calculations provided by ANSYS Mechanical is used to investigate the effects of turbine rotation on the dynamic response of the system. Rotation speed ranging between 0 to 150 rad/s was examined to cover the whole operating range of commercial instances. The modal analysis ends up with first six mode shapes of both rotor configurations. As a result, the displacement of the proposed configurations reduced effectively. Apparent variations in Campbell diagrams of both cases indicate that prestressed configuration has its resonant frequencies far away from turbine operation speeds and thus remarkably higher safety factor against whirling and probable following failures.
Several methods of incorporating sago pith waste (SPW) into poly(vinyl alcohol) (PVA) had been conducted: (i) dry blending (PVA/SPW/G), (ii) blending of SPW and pre-plasticized PVA (pPVA/SPW/G) and (iii) blending of pre-plasticized of both PVA and SPW (pPVA/pSPW). The effect of the compounding method on the mechanical and water absorption properties were investigated. The addition of SPW into PVA greatly reduced the tensile strength and elongation at break. The tensile strength and elongation at break of PVA/SPW composites with identical geometry during compounding stage (powder/powder and pellet/pellet), which were PVA/SPW/G and pPVA/pSPW yielded the highest value. The percentage of water absorbed by PVA/SPW/G (without pre-plasticization) was the highest, followed by pPVA/pSPW and pPVA/SPW/G.
This study was conducted to screen the most suitable coating material for the production of microencapsulated fish oil powder using ternary blends of maltodextrin (15, 25 % w/w), Arabic gum (2.5, 7.5 % w/w), and methylcellulose (0.5, 1.5 % w/w). The physical properties of fish oil emulsion and encapsulated powders were evaluated. Arabic gum (5 % w/w) showed the most significant (p
The need for power-efficient devices, such as smart sensor nodes, mobile devices, and portable digital gadgets, is markedly increasing and these devices are becoming commonly used in daily life. These devices continue to demand an energy-efficient cache memory designed on Static Random-Access Memory (SRAM) with enhanced speed, performance, and stability to perform on-chip data processing and faster computations. This paper presents an energy-efficient and variability-resilient 11T (E2VR11T) SRAM cell, which is designed with a novel Data-Aware Read-Write Assist (DARWA) technique. The E2VR11T cell comprises 11 transistors and operates with single-ended read and dynamic differential write circuits. The simulated results in a 45 nm CMOS technology exhibit 71.63% and 58.77% lower read energy than ST9T and LP10T and lower write energies of 28.25% and 51.79% against S8T and LP10T cells, respectively. The leakage power is reduced by 56.32% and 40.90% compared to ST9T and LP10T cells. The read static noise margin (RSNM) is improved by 1.94× and 0.18×, while the write noise margin (WNM) is improved by 19.57% and 8.70% against C6T and S8T cells. The variability investigation using the Monte Carlo simulation on 5000 samples highly validates the robustness and variability resilience of the proposed cell. The improved overall performance of the proposed E2VR11T cell makes it suitable for low-power applications.
A steady laminar mixed convection boundary layer flow about an isothermal solid sphere embedded in a porous medium filled with a nanofluid has been studied for both cases of assisting and opposing flows. The transformed boundary layer equations were solved numerically using an implicit finite-difference scheme. Three different types of nanoparticles, namely Cu, Al2O3 and TiO2 in water-based fluid were considered. Numerical solutions were obtained for the skin friction coefficient, the velocity and temperature profiles. The features of the flow and heat transfer characteristics for various values of the nanoparticle volume fraction and the mixed convection parameters were analyzed and discussed.
Natural organic matters (NOMs) have been found to be the major foulant in the application of ultrafiltration (UF) for treating surface water. Against this background, although hydrophilicity has been demonstrated to aid fouling mitigation, other parameters such as membrane surface morphology may contribute equally to improved fouling resistance. In this work, with humic acid solution as the model substance, the effects of titanium dioxides (TiO2) types (PC-20, P25, and X500) on membrane anti-fouling and defouling properties were comparatively analysed. The aims are (1) to determine the correlation between membrane surface morphology and membrane fouling and (2) to investigate the anti-fouling and UV-cleaning abilities of PVDF/TiO2 mixed-matrix membranes with different membrane topographies and surface energy conditions. The mixed-matrix membrane with P25 TiO2 exhibited the most significant UV-defouling ability, with a high irreversible flux recovery ratio (IFRR(UV)) of 16.56 after 6 h of UV irradiation, whereas that with X500 TiO2 exhibited both superior anti-fouling and defouling properties due to its smoother surface and its highly reactive surface layer.
We consider the reduced dynamics of a molecular chain weakly coupled to a phonon bath. With a small and constant inhomogeneity in the coupling, the excitation relaxation rates are obtained in closed form. They are dominated by transitions between exciton modes lying next to each other in the energy spectrum. The rates are quadratic in the number of sites in a long chain. Consequently, the evolution of site occupation numbers exhibits longer coherence lifetime for short chains only. When external source and sink are added, the rate equations of exciton occupation numbers are similar to those obtained earlier by Fröhlich to explain energy storage and energy transfer in biological systems. There is a clear separation of timescale into a faster one pertaining to internal influence of the chain and phonon bath, and a slower one determined by external influence, such as the pumping rate of the source, the absorption rate of the sink, and the rate of radiation loss. The energy transfer efficiency at steady state depends strongly on these external parameters and is robust against a change in the internal parameters, such as temperature and inhomogeneity. Excitations are predicted to concentrate to the lowest energy mode when the source power is sufficiently high. In the site basis, this implies that when sustained by a high power source, a sink positioned at the center of the chain is more efficient in trapping energy than a sink placed at its end. Analytic expressions of energy transfer efficiency are obtained in the high power and low-power source limit. Parameters of a photosynthetic system are used as examples to illustrate the results.
A new smart grid system is widely used for energy supply system because it is simple, available, low cost, high efficiency and environmentally friendly. Conventionally, inverter techniques are utilised to convert input DC into output AC with the same frequency and phase. This process suffers the same problem which is a higher harmonic distortion, phase synchronisation, lower quality of waveform and long distance, among others. In this paper, three phase synchronous inverters (PSI) were used to direct synchronous PWM control, LCL filter, three phase RLC load, three phase Yg-Delta transformer, 5 km feeder with 2 MW load. PWM was used to generate the pulse signal for synchronisation. However, LCL filters were used to remove the noise in inverter output and transformer output side of the design. A balanced three phase load (10 kVAR) and also the input DC voltage 500 V were considered in this design. Three phase transformer (100kVA/260V/25kV) was used to increase the inverter output voltage and current with the fundamental frequency (50 Hz). The system conversion efficiency was 99.96% and phase synchronous error for each phase was approximately 4.5 degrees.
Welding parameters obviously determine the joint quality during the resistance spot welding process. This study aimed to investigate the effect of welding current and electrode force on the heat input and the physical and mechanical properties of a SS316L and Ti6Al4V joint with an aluminum interlayer. The weld current values used in this study were 11, 12, and 13 kA, while the electrode force values were 3, 4, and 5 kN. Welding time and holding time remained constant at 30 cycles. The study revealed that, as the welding current and electrode force increased, the generated heat input increased significantly. The highest tensile-shear load was recorded at 8.71 kN using 11 kA of weld current and 3 kN of electrode force. The physical properties examined the formation of a brittle fracture and several weld defects on the high current welded joint. The increase in weld current also increased the weld diameter. The microstructure analysis revealed no phase transformation on the SS316L interface; instead, the significant grain growth occurred. The phase transformation has occurred on the Ti6Al4V interface. The intermetallic compound layer was also investigated in detail using the EDX (Energy Dispersive X-Ray) and XRD (X-Ray Diffraction) analyses. It was also found that both stainless steel and titanium alloy have their own fusion zone, which is indicated by the highest microhardness value.
The optimal functionalities of materials often appear at phase transitions involving simultaneous changes in the electronic structure and the symmetry of the underlying lattice. It is experimentally challenging to disentangle which of the two effects--electronic or structural--is the driving force for the phase transition and to use the mechanism to control material properties. Here we report the concurrent pumping and probing of Cu2S nanoplates using an electron beam to directly manipulate the transition between two phases with distinctly different crystal symmetries and charge-carrier concentrations, and show that the transition is the result of charge generation for one phase and charge depletion for the other. We demonstrate that this manipulation is fully reversible and nonthermal in nature. Our observations reveal a phase-transition pathway in materials, where electron-induced changes in the electronic structure can lead to a macroscopic reconstruction of the crystal structure.