The objective of this paper is to model the extraction of carotenoid with supercritical carbon dioxide as the solvent. Experimental data for the high pressure vapour-liquid phase equilibrium of the binary system carbon dioxide-carotenoid was reviewed for the elevated temperatures of 313.15, 323.15, 333.15 K and pressures up to 500 bar. The experimental data was correlated and modeled using Redlich-Kwong equation of state and regular solution methods. The use of the equation of state as an empirical correlation for collating and predicting liquid-liquid and liquid-dense fluid equilibria is discussed. It was concluded that the estimation of some of the parameters required for these calculations would be difficult if the solute (carotenoid) was a complex substance about which little was known apart from its structural formula. An alternative procedure is to apply activity coefficient expression of the regular solution theory type to each phase. Calculations along these lines are described and the physical basis for applying these methods under the relevant conditions is discussed. The regular solution theory approach in particular was found to be encouraging for the mutual miscibility calculations for heavy components (such as carotenoid) particularly for substances sensitive to temperature, though the interaction parameters for he prediction activity coefficients must be regarded as pressure dependent.
Severe gingival recession caused by dehiscence usually present a challenging task to the clinician as any mucogingival surgery without bony regeneration will not 'prevent the condition from recurring. The procedures of guided tissue regeneration ( GTR ) which allow regeneration of the lost periodontium may offer some solution to the condition. This paper reports on the use of a non-resorbable GTR membrane to treat an isolated lower incisor gingival recession associated with dehiscence.
Aluminium (Al) is a low cost, lightweight and corrosion resistant material, which corrodes when exposed to pitting agents. Palm olein exhibits characteristics, which indicate its suitability as a corrosion inhibitor. Tween 20, hexane and diethyl triamine were used as additives to Palm olein to form the inhibitor formulation POT2OHA. The inhibition efficiency (IE) and behaviour of the POT2OHA were determined using potentiodynamic polarization in which Al 6061 samples were immersed in a 1 M HC1 solution at 26, 50 and 70 °C in the presence of different POT2OHA concentrations: 0, 0.03, 0.07, 0.10, 0.13 and 0.17 M The IE increased with increasing POT2OHA concentration, but decreased with increasing temperature. The work presented indicates that POT2OHA is a mixed-type inhibitor capable of inhibiting both corrosive anodic and cathodic reactions. According to the Langmuir isotherm results POT2OHA adsorbs on the A16061 surface through semiphys iosorption and/or semi-chemisorption. The POT2OHA adsorption mechanism on Al 6061 takes through the protonation of micelles by the HC1 solution, whereby protonated micelles in the presence of chloride ions adsorb on both cathodic and anodic surface corrosion sites.
In the moving layer of particles with variable concentration, the shear estimation is not directly predictable and there is no existing clear mathematical or empirical formula to achieve this objective. This paper presents a developed approach to estimate the shear forces in a flow having suspended and moving layers of solid particles in liquid flow. The two-layer approach was taken whereby the flow consisting of one upper suspended layer of particles in the liquid, and the bottom layer was the moving bed of particles. In the present work, the method of finding the force acting on the pipe wall by the particles in the layer, termed as the ‘dry force’, was presented using a “pseudo hydrostatic pressure” method. To attain the equation for the dry force, a mathematical approach is taken with the assumptions that the flow is horizontal, two-phase pipe flow (solid in Newtonian liquid), incompressible and it is at steady-state. The analysis was conducted considering various particles densities, various concentrations in the suspended layer and different thicknesses of the moving bed. Changing the concentration in the suspended layer from 0.00001 up to 0.001 didn’t showed significant changes in the dry force evaluation. The dry friction force is increasing with increasing moving bed thickness. The developed mathematical model can be
applicable in solving for the shear force in horizontal solid liquid two-phase flows.
Many studies have been carried out using different metaheuristic algorithms on optimisation problems in various fields like engineering design, economics and routes planning. In the real world, resources and time are scarce. Thus the goals of optimisation algorithms are to optimise these available resources. Different metaheuristic algorithms are available. The firefly algorithm is one of the recent metaheuristic algorithms that is used in many applications; it is also modified and hybridised to improve its performance. In this paper, we compare the Standard Firefly Algorithm, the Elitist Firefly Algorithm, also called the Modified Firefly Algorithm with the Chaotic Firefly Algorithm, which embeds chaos maps in the Standard Firefly Algorithm. The Modified Firefly Algorithm differs from the Standard Firefly Algorithm in such a way that the global optimum solution at a particular iteration will not move randomly but in a direction that is chosen from randomly generated directions that can improve its performance. If none of these directions improves its performance, then the algorithm will not be updated. On the other hand, the Chaotic Firefly Algorithm tunes the parameters of the algorithms for the purpose of increasing the global search mobility i.e. to improve the attractiveness of fireflies. In our study, we found that the Chaotic Firefly Algorithms using three different chaotic maps do not perform as well as the Modified Firefly Algorithms; however, at least one or two of the Chaotic Firefly Algorithms outperform the Standard Firefly Algorithm under the given accuracy and efficiency tests.
In this paper, an implicit 2-point Block Backward Differentiation formula (BBDF) method was considered for solving Delay Differential Equations (DDEs). The method was implemented by using a constant stepsize via Newton Iteration. This implicit block method was expected to produce two points simultaneously. The efficiency of the method was compared with the existing classical 1-point Backward Differentiation Formula (BDF) in terms of execution time and accuracy.
The in vitro cytotoxic potential of locally produced dental porcelain was evaluated in this study. The cellular response of human osteoblast and fibroblast cell lines were assessed using MTT assay by incubating with the fluid extract of dental porcelain powder and dental porcelain discs (direct test). Aging process was carried out by submerging the discs into 3% bovine serum albumin (BSA) solution. Tests on extracts showed that dental porcelain was significantly different from the control at a concentration of 250 mg/ml. Direct test showed that dental porcelain after aging was not significantly different from the control with a mean (SD) of 89.2 (13.4)%, whereas, it was significantly different from the control before conditioning of BSA with a mean (SD) of 88.5 (12.1)%. However, the dental porcelain caused mild suppression of succinate dehydrogenase activity (
Electrodeposition of white copper-tin alloys (including white miralloys) has been done onto planar mild steel substrates from alkaline cyanide solutions at 65 0 C. The chemical composition of the coating is influenced by plating bath composition and current density. White miralloy can be produced from the test solution containing 10 g/l CuCN2 - , 45 g/l Na2SnO3, 25 g/l NaCN, and 12 g/l NaOH at current density about 5 mA/cm 2 . The local compositions of the coating cross section were analyzed using EDX installed in a FESEM operated at an accelerating voltage of 20 kV. The phases formed during co-deposition process were identified using XRD at 25 mA current and 35 kV voltage.
The accumulation of tear film proteins as well as microbes colonization onto worn contact lenses can be eliminated conventionally by mechanical rubbing during the cleaning process. Lens2® functions in rotation manner to loosen the deposits on the contact lens and has antimicrobial coating to keep lenses away from contamination. The objective of this study was to determine the efficiency of Lens2® to remove deposited protein and reduce microbial contamination compared to conventional method. Twenty-eight subjects each wore a pair of contact lens FDA Group 1 (Polymacon, SoftLens® 38, Bausch & Lomb) for one month and cleaned them using multipurpose solution (COMPLETE® MoisturePLUSTM, Advanced Medical Optics) separately using two different methods. The right lens was cleaned conventionally while the left lens were cleaned using the Lens2®. The control group of thirteen subjects each wore a pair of contact lens for the same period and cleaned both conventionally. These lenses and its cases were then analyzed for protein deposition using Bichinchoninic Acid Assay (BCA) Kit (Sigma, USA) in 96-well plate. Microbial contamination was determined by culturing the samples on nutrient agar for bacteria and fungi and non-nutrient agar for amoeba isolation. The mean of total protein on control lenses (17.014 ± 13.246 µg/mL) was not significantly different from those on the Lens2® (21.623 ± 19.127 µg/mL). There were also low growth numbers of amoeba in each group of samples. Interestingly, there were no growths of amoeba from all Lens2® samples collected. There was also low growth numbers of bacteria in each sample group whereby Lens2® had the lowest growth of bacteria. No growth of fungi was obtained from all samples. The automatic lens cleaner, Lens2® was found to be as efficient as the conventional cleaning method. However, the Lens2® has additional advantage because of its antimicrobial material and need shorter time in the cleaning process as well as easy and effective.
The adsorption equilibrium time and effects of pH and concentration of ¹⁴C-labeled chlorpyrifos
O,O-diethyl O-(3, 5, 6 trichloro-2-pyridyl)-phosphorothiote in soil were investigated. Two types of Malaysian soil under oil palm were used in this study; namely clay loam and clay soil obtained from the Sungai Sedu and Kuala Lumpur International Airport (KLIA) Estates, respectively. Equilibrium studies of chlorpyrifos between the agricultural soil and the pesticide solution were conducted. Adsorption equilibrium time was achieved within 6 and 24 hours for clay loam and clay soil, respectively. It was found that chlorpyrifos adsorbed by the soil samples was characterized by an initial rapid adsorption after which adsorption remained approximately constant. The percentage of ¹⁴C-labeled chlorpyrifos adsorption on soil was found to be higher in clay loam than in clay soils. Results of the study demonstrated that pH affected the adsorption of chlorpyrifos on both clay loam and clay soils. The adsorption of chlorpyrifos on both types of soil was higher at low pH with the adsorption reduced as the pH increased. Results also suggest that chlorpyrifos sorption by soil is concentration dependent.
The purpose of this study was to determine the adsorption coefficient (Koc) of chlorpyrifos in clay soil by measuring the Freundlich adsorption coefficient (Kads(f)) and desorption coefficient (1/n value) of chlorpyrifos. It was found that the Freundlich adsorption coefficient (Kads(f)) and the linear regression (r 2 ) of the Freundlich adsorption isotherm for chlorpyrifos in the clay soil were 52.6 L/kg and 0.5344, respectively. Adsoprtion equilibrium time was achieved within 24 hours for clay soil. This adsoprtion equilibrium time was used to determine the effect of concentration on adsorption. The adsorption coefficient (Koc) of clay soil was found to be 2783 L/kg with an initial concentration solution of 1 µg/g, soil-solution ratio (1:5) at 30 o C when the equilibrium between the soil matrix and solution was 24 hours. The Kdes decreased over four repetitions of the desorption process. The chlorpyrifos residues may be strongly adsorbed onto the surface of clay.
In the current research, osmotic dehydration of red pitaya (Hylocereus polyrhizusis) cubes using sucrose solution at mild temperature (35ºC) was investigated. Sucrose solution (40, 50 and 60% w/w) was employed for osmotic dehydration process. Responses of weight reduction (WR), solid gain (SG), water loss (WL), color (L*, a* and b*) and texture (hardness) were evaluated. It was found that sucrose concentration significantly (p < 0.05) affected the mass transfer terms during osmosis process. The results obtained revealed an increase in yellowness (b*), decrease in lightness (L*) and redness (a*) as the sucrose concentration increased. Furthermore, osmotically dehydrated samples were considerably softer than untreated samples. Increasing of sucrose concentration and dehydration time caused softer tissue of dehydrated product compared with the fresh red pitaya.
Introduction: The purpose of the present study was to investigate exploratory factor analysis of the
Beck Anxiety Inventory (BAI) and reports its reliability and validity in Malaysia. Method: One thousand
and ninety participants from four different samples (namely students, general population, medical and
psychiatric patients) completed the Malay version of Beck Anxiety Inventory, as well as additional
questionnaires such as Fear Questionnaire, Anxiety Sensitivity Index, Depression Anxiety Stress Scale, and Catastrophic Cognition Questionnaire. Results: Exploratory factor analysis revealed a three factor solution and accounted for 48.01% of the total variance. The three-factor structure appeared to be; subjective anxiety, autonomic, and neurophysiology. The Cronbach alpha coefficients (α) ranged from 0.66 to 0.89 with satisfactory overall alpha value (.91). Evidence was also found acceptable concurrent validity of the BAI-Malay (range between r=.22 to r=.67). Conclusion: This study shows that the BAIMalay is a reliable and valid instrument to measure symptoms of anxiety in the Malay population
and can be used in research and clinical service in Malaysia. However, replication of study by using
confirmatory factor analysis and application of the instrument among anxiety patients worth of further
investigation.
Lattice Boltzmann Model for Shallow Water Equation with Turbulence Modeling (LABSWETM) is used to study the flow patterns of sidewall friction effects. The lattice Boltzmann method (LBM) approach in recovery the macroscopic governing equation which is shallow water equation from the microscopic flow behavior of particle movement as described by kinetic theory is explored. With the solution of force term to be used in lattice Boltzmann equation, the boundary condition of LBM is explored. With the use of bed and wall friction coefficients, the importance of Manning’s coefficient in determining the outcome of flow patterns simulation is explained. For model verification, the model represents a straight channel with a circular cavity attached to it. The result of this simulation includes the water circulation patterns, cross-section of average velocity distribution, and water depth. For validation, the cross-sections of the model in term of velocity vectors are compared against alternative numerical and experimental data.
Epoxidised Natural Rubber (ENR) is now a commercially available polymer produced by chemical modification of natural rubber. Currently, three types of ENR are commercially available, and these are ENR 10, ENR 25, and ENR 50 with 10%, 25%, and 50% mol epoxidation, respectively. Studies on prevulcanisation of ENR 50 and postvulcanisation of the latex films were carried out. The objective of this study was to develop ENR 50 that could be dipped easily in coagulant dipping solution to produce dipped products. Several attempts were made by compounding prevulcanised ENR 50 at various sulphur levels ranging from 0.5 to 3.0 pphr. Using suitable coagulant dipping systems, ENR 50 film could be formed despite the high contents of non-ionic surfactant. It was found that the tensile strength of prevulcanised ENR 50 film decreased with the increase in the sulphur level. The results show that as level of sulphur increased, M300 also increased to an optimum value of 1.5 pphr of sulphur. For the postvulcanised ENR 50 film, however, the tensile strength increased and then decreased with the increasing sulphur level. Meanwhile M300 increased with the increasing postvulcanization time and sulphur level. The postvulcanisation of ENR 50 film seems to be a more effective way of increasing tensile properties than by prevulcanisation of ENR 50.
Konjac glucomannan (KGM) was treated with or without sonication and/or hydrochloric acid (HCl).
Hydrolysis effects on KGM were studied for properties such as degree of hydrolysis, fluidity, molecular mass, and creep properties. The degree of hydrolysis for sonicated KGM and acid treated KGM were not significantly different. However, the combination treatment of acid hydrolysis and sonication was found effective in yielding a smaller molecular weight fraction of KGM and solution with higher fluidity. From the creep analysis, KGM treated with combination treatment exhibited the highest compliance among samples tested. In general, ultrasound mediated acid hydrolysis was found to be a promising technique in degrading high molecular weight biopolymer. This could be attributed to a localized high temperature and high shear forces generated during cavitation that facilitated the endothermic acid hydrolysis.
This paper presents the solution to a calculation of the pH of a very dilute solution of a strong acid or base, taking into account the effect of the hydronium or hydroxyl ions generated from the ionisation of the strong acid or base on the ionisation of water, as a second very weak acid. To be solved successfully, this calculation involves the concepts of conservation of charge, pH and the application of the general solution to a quadratic equation. Such an exercise involves the application of skills in basic numeracy, and can provide a core of understanding that can prepare students for
many different sorts of calculations that represent reallife problems in the medical and biological sciences.A programme is presented in C++ which enables the work of students to be individualised so that each student in a class can work through a slightly different pH calculation, in such a way that a class supervisor can quickly check each student’s result for accuracy. This exercise is presented as a potential means of enabling students to undertake and master similar types of calculations involving simple or more complex equilibria.
Introduction: Knowledge, attitude as well as adoption of pharmacogenomics in clinical practice among the pharmacists and physicians in Malaysia have not been reported. This cross-sectional study explores various facets of the two professions as related to pharmacogenomics to determine the need and preferred method to improve education among them. This study also aims to identify the current state of pharmacogenomics practice in Malaysia to help identify barrier and solution to reap advantages from pharmacogenomics practices. Methods: A questionnaire consisting of 38 questions in five parts was adopted and validated. It explores the respondents’ characteristics, attitude, knowledge, adoption and education. It was distributed online to 1500 pharmacists and physicians over five months. Results: Pharmacists differed from the physicians in terms of attitude, knowledge, adoption and education. Overall, adoption rate of pharmacogenomics was found to be low but its anticipation for future adoption is high, and benefits were reported by healthcare professionals who have used the test in a clinical setting. Majority of respondents had poor to fair knowledge and nearly half have had no prior formal teaching on pharmacogenomics. Interest in the education is very high, and most of them preferred to learn pharmacogenomics via continuous professional education programs. Conclusion: Pharmacogenomics is a field that promises many benefits, but to reap these benefits require its implementation in clinical setting. Pharmacists and physicians need to be equipped with adequate knowledge and positive attitude towards pharmacogenomics.
Thermal characterization of sugar palm fibre (SPF), reinforced high impact polystyrene (HIPS)
composites, was studied by means of thermogravimetric analysis. The effects of alkaline treatment and compatibilizing agent on the thermal stability of the composites were evaluated. Alkaline treatment was carried out by soaking the fibres in 4 and 6% of NaOH solution, while treatment with compatibilizing agent was employed by adding 2 and 3% maleic anhydride-graft-polystyrene (MA-g-PS) to the composites. Both the treatments were aimed to improve the mechanical performance of the composites. From the study, the thermal stability of the treated composites was found to be higher than that of untreated composites. It is shown that the incorporation of sugar palm fibre influences the degree of thermal stability of the composites. The treatments on composites also contributed to shifting the peak temperature of degradation of the composites. In other words, there are strong chemical reactions between the components of the treated composites. The thermal stability of the composites, with alkaline treatment and compatibilizing agent, was found to be better as compared to those of the untreated composites.
This paper presents on ionic conductivity of MG30-PEMA blend solid polymer electrolytes (SPEs) prepared by solution cast technique. The analysis has shown that conductivity increases with the increasing salt composition. It is observed via x-ray diffraction analysis that the crystallinity of the sample decreased with the amount of salt composition as expected. It is also observed that the dielectric value increases with increasing amount of LiCF3SO3 in the sample. Surface morphology revealed that ion aggregation occurred after optimum conductivity which has lowered the conductivity.