Waste materials from the agricultural and industries can cause problems to human health and the environment when improperly disposed and managed. Due to rapid development in construction, the demand of cement in concrete has increased dramatically. Therefore, wastes such as rice husk, eggshell, glass, fly ash and many more can be used in construction industry to minimize the environmental impact and producing new material on construction industry. Many studies have been conducted as an effort to find replacement materials to substitute cement in concrete.
Waste materials from the agricultural and industries can cause problems to human health and the environment when improperly disposed and managed. Due to rapid development in construction, the demand of cement in concrete has increased dramatically. Therefore, wastes such as rice husk, eggshell, glass, fly ash and many more can be used in construction industry to minimize the environmental impact and producing new material on construction industry. Many studies have been conducted as an effort to find replacement materials to substitute cement in concrete.
The increase in wastes generated from jackfruit seeds has been largely under-utilized in Malaysia. Due to the high nutritional and medicinal content embedded in the cellulosic structure of jackfruit wastes, a need then arises for their physicochemical elucidations. In this study, the extraction of Artocarpus heterophyllus seed was carefully investigated using Taguchi orthogonal optimization design. Complete functional group characteristics and chemical profile of the A. heterophyllus seed extracts were obtained using different physicochemical characterization. The optimal conditions of the microwave extraction parameters were determined at 5 min of irradiation time, 450 W of power and 50 °C of temperature. Under this condition, the optimal yield of 17.34 (mg/g) % was achieved at an SNR ratio of 24.78. The mass spectrometry analysis tentatively identified a total of 90 and 148 secondary metabolites at positive and negative ESI modes, respectively. The chemical profile obtained provided a baseline reference for further investigation on the food and medicinal bioactive from Artocarpus heterophyllus seed oleoresins. The FT-infrared emission spectrum shows the presence of some specific carbohydrates and amide protein functional groups directly linked to C-O (1008 cm-1) the carbonyl (C=O) groups, respectively. Moreover, the morphological characteristics of the jackfruit raw and crude extracts conspicuously revealed large-sized globules which suggest the carbohydrates and protein contents. The result of this study indicates that the use of microwave extraction technology produced high-quality extracts with lower degradation of the thermal labile constituents. This will assist in determining the suitable conditions necessary for the total recovery of medicinal and nutritional constituents and conversion of agricultural waste products into useful products.
This review of literature provides an overview on the compositional data of Rambutan (Nephelium lappaceum Linn.) and rambutan seed fat for usage in chocolate product. It is a seasonal fruit native of west Malaysia and Sumatra. It is harvested when the fruit have reached optimum visual and organoleptic quality. Rambutans rapidly deteriorate unless proper handling techniques are employed. The rambutan fruits are deseeded during processing and these seeds (~ 4-9 g/100 g) are a waste by-product of the canning industry. And some studies was showed that rambutan seed possesses a relatively high amount of fat and these fats are similar to those of cocoa fat, although have some different physical properties. In the present research about rambutan seed fat continued increasing due to from previous research was found that this fat can use as substitute in cocoa butter for chocolate products. Therefore, the extracted fat from rambutan seed not only could be used for manufacturing candles, soaps, and fuels, but it also has a possible to be a source of natural edible fat with feasible industry use.
In this study, pineapple cannery waste materials were used as substrate for the microbial production of vanillic acid and vanillin by Aspergillus niger I-1472 and Pycnoporus cinnabarinus MUCL 39533. Biotransformation of ferulic acid from pineapple waste by A. niger I-1472 to vanillic acid was optimized using Response Surface Methodology (RSM). A central composite rotatable design was used to allocate treatment combinations and factors tested for their influence on vanillic acid production were inoculum size, yeast extract concentration, diammonium tartrate concentration and initial medium pH. The amount of vanillic acid produced was used as the response for the fermentation study and was assumed to be under the influence of the four factors tested. The estimated conditions for optimal vanillic acid production were inoculum size, 3.08 ×105 CFU mL-1; yeast extract, 0.37 gL-1; diammonium tartrate, 3.88 gL-1 and initial pH, 4.3. Subsequent biotransformation of vanillic acid by P. cinnabarinus MUCL 39533 to vanillin was enhanced with the addition of resin. Under these optimal conditions, 141.00 mgL-1 of vanillin was produced from 5 g of pineapple cannery waste.
Shock is a clinical challenge to neonatal intensivists and pediatricians alike. It occurs in critically ill babies for many reasons, but the main cause is sepsis that kills more than a million newborn globally every year. This article is designed to help young doctors and trainees have a better understanding of shock in the neonatal period and its management. The paper reviews the basic pathophysiology, risk factors, clinical investigation, management, supportive care, and complications in the common types of shock seen in neonates. Treatment is governed largely by the underlying cause, with the ultimate goal of achieving adequate tissue perfusion with delivery of oxygen and substrates to the cells, and removal of toxic metabolic waste products. Intervention needs to be anticipatory and urgent to prevent progression to uncompensated and irreversible shock respectively. Early recognition and urgent effective management are crucial to successful outcomes.
Co-pyrolysis of biomass with abundantly available materials could be an economical method for production of bio-fuels. However, elimination of oxygenated compounds poses a considerable challenge. Catalytic co-pyrolysis is another potential technique for upgrading bio-oils for application as liquid fuels in standard engines. This technique promotes the production of high-quality bio-oil through acid catalyzed reduction of oxygenated compounds and mutagenic polyaromatic hydrocarbons. This work aims to review and summarize research progress on co-pyrolysis and catalytic co-pyrolysis, as well as their benefits on enhancement of bio-oils derived from biomass. This review focuses on the potential of plastic wastes and coal materials as co-feed in co-pyrolysis to produce valuable liquid fuel. This paper also proposes future directions for using this technique to obtain high yields of bio-oils.
Lansium domesticum peel (LDP), a waste material generated from the fruit consumption, was evaluated as a biosorbent for nickel removal from aqueous media. The effects of dosage, contact time, initial pH, initial concentration and temperature on the biosorption process were investigated in batch experiments. Equilibrium data were fitted by the Langmuir, Freundlich, Temkin and Dubinin-Radushkevich models using nonlinear regression method with the best-fit model evaluated based on coefficient of determination (R(2)) and Chi-square (χ(2)). The best-fit isotherm was found to be the Langmuir model exhibiting R(2) very close to unity (0.997-0.999), smallest χ(2) (0.0138-0.0562) and largest biosorption capacity (10.1mg/g) at 30°C. Kinetic studies showed that the initial nickel removal was rapid with the equilibrium state established within 30min. Pseudo-second-order model was the best-fit kinetic model indicating the chemisorption nature of the biosorption process. Further data analysis by the intraparticle diffusion model revealed the involvement of several rate-controlling steps such as boundary layer and intraparticle diffusion. Thermodynamically, the process was exothermic, spontaneous and feasible. Regeneration studies indicated that LDP biosorbent could be regenerated using hydrochloric acid solution with up to 85% efficiency. The present investigation proved that LDP having no economic value can be used as an alternative eco-friendly biosorbent for remediation of nickel contaminated water.
Urbanization is one of the leading causes of urban flooding as rapid development produces more impervious areas in cities. The application of green roofs is regarded as an effective technology to minimize the adverse effects of urban development. The stormwater management capacities of green roofs have been extensively acknowledged, and they can retain rainfall and detain runoff. Nevertheless, Malaysia has experienced few green roof applications, and only limited literature is available concerning such topics. Additionally, the incorporation of waste and recycled material in green roof designs must be considered to ensure such projects benefit the environment as well as the economy. Therefore, the construction of a green roof utilizing recycled waste materials was attempted. An extensive green roof was constructed using beach morning glory and creeping ox-eye plants as vegetation layers, along with coconut waste, i.e., coconut fiber and coconut shell, as the medium for the filter and drainage layer, respectively. According to the results, the use of recycled coconut waste materials in the green roof operations reduced the peak flow by as much as 86%, while the use of commercial materials led to a reduction of 67%.
The first report on the emergence of microplastic in Malaysian marine waters was documented in this study. Water samples were collected from two regions, namely Kuala Nerus and Kuantan port, as the representatives of different anthropogenic activities. Identification of microplastic was performed based on physical characteristics (colour, shape, density) and chemical characterisation (ATR-FTIR analysis) for a functional group of polymers. Fragment type, black or grey colour and high density (>1.02 g cm-3) of microplastic were the most prevalent characteristics found in both areas. Two principal components (density and colour) rendered explained about 95.3% (Kuantan) and 95.6% (Kuala Nerus) of the total variance. Six possible polymer materials were identified, namely polyester, polystyrene, polyamide, polyvinyl chloride, polypropylene, and polyethylene. The findings of the study provided good baseline information on marine debris issue in Malaysia.
Fruits are important food commodities that can be consumed either raw or processed and are valued for their taste, nutrients, and healthy compounds. Mangifera pajang Kosterm (bambangan) is an underutilized fruit found in Malaysia (Sabah and Sarawak), Brunei, and Indonesia (Kalimantan). It is highly fibrous and juicy with an aromatic flavour and strong smell. In recent years, bambangan fruit has been gaining more attention due to its high fibre, carotenoid content, antioxidant properties, phytochemicals, and medicinal usages. Therefore, the production, trade, and consumption of bambangan fruit could be increased significantly, both domestically and internationally, because of its nutritional value. The identification and quantification of bioactive compounds in bambangan fruit has led to considerable interest among scientists. Bambangan fruit and its waste, especially its seeds and peels, are considered cheap sources of valuable food and are considered nutraceutical ingredients that could be used to prevent various diseases. The use of bambangan fruit waste co-products for the production of bioactive components is an important step towards sustainable development. This is an updated report on the nutritional composition and health-promoting phytochemicals of bambangan fruit and its co-products that explores their potential utilization. This review reveals that bambangan fruit and its co-products could be used as ingredients of dietary fibre powder or could be incorporated into food products (biscuits and macaroni) to enhance their nutraceutical properties.
A chemical method to synthesize amorphous silica nanoparticles from the incinerated paddy straw has been introduced. The synthesis was conducted through the hydrolysis by alkaline-acidic treatments. As a result, silica particles produced with the sizes were ranging at 60-90 nm, determined by high-resolution microscopy. The crystallinity was confirmed by surface area electron diffraction. Apart from that, chemical and diffraction analyses for both rice straw ash and synthesized silica nanoparticles were conducted by X-ray diffraction and Fourier-transform infrared spectroscopy. The percentage of silica from the incinerated straw was calculated to be 28.3. The prominent surface chemical bonding on the generated silica nanoparticles was with Si-O-Si, stretch of Si-O and symmetric Si-O bonds at peaks of 1090, 471, and 780 cm-1, respectively. To confirm the impurities of the elements in the produced silica, were analyzed using X-ray photoelectron spectroscopy and energy dispersive X-ray spectroscopy. The stability of silica nanoparticles was investigated using thermogravimetric analysis and zeta potential. The measured size from zeta potential analysis was 411.3-493 nm and the stability of mass reduction was located at 200 °C with final amount of mass reduced ∼88% and an average polydispersity Index was 0.195-0.224.
The feasibility of using waste glycerol from the biodiesel industry for biosynthesis of polyhydroxyalkanoate (PHA) by Burkholderia cepacia BPT1213 was evaluated. Culture conditions were optimized by growing B. cepacia BPT1213 in mineral salt medium supplemented with 2% waste glycerol in a 2.5 L bioreactor. Response surface methodology was used to determine the influence of aeration rate (0.6-1.8 vvm), agitation speed (100-300 rpm), and cultivation period (48-72 hr) on PHA production. The optimum conditions for the growth and PHA accumulation were 1.5 vvm, 300 rpm, and 72 hr, with predicted values of 5.08 g/L cell dry weight (CDW), 66.07% PHA content, and 3.35 g/L total PHA concentration. Using these conditions, the experimental system produced 5.63 g/L of CDW with 64.00% wt/wt PHA content, which is threefold higher PHA concentration (3.60 g/L) compared to the non-optimized conditions. The melting temperature (Tm ) of purified PHA was 173.45 ± 1.05°C. In conclusion, the statistical approach was significantly increased the PHA production using waste glycerol as the sole carbon source.
In a commercial oyster mushroom farm, from 300 g of the total harvest, only the cap and stem of the fruiting body parts are harvested (200 g) while the unused lower section called fruiting-body-base (FBB) is discarded (50 g). A new antioxidative FBB flour (FBBF) conversion to mixed-ratio chicken patty was recently developed which converts 16.67% of FBB into an edible flour. At the initial stage, pretreatments of FBBF were optimized at particle size (106 µm) and citric acid concentration (0.5 g/100 mL) to improve flour antioxidant responses. Such pretreatments boosted total phenolic content (2.31 ± 0.53 mg GAE/g) and DPPH (51.53 ± 1.51%) of pretreated FBBF. Mixed-ratio chicken patty containing FBBF (10%, 20%, 30%) significantly (P
Construction and demolition waste continues to sharply increase in step with the economic growth of less developed countries. Though the construction industry is large, it is composed of small firms with individual waste management practices, often leading to the deleterious environmental outcomes. Quantifying construction and demolition waste generation allows policy makers and stakeholders to understand the true internal and external costs of construction, providing a necessary foundation for waste management planning that may overcome deleterious environmental outcomes and may be both economically and environmentally optimal. This study offers a theoretical method for estimating the construction and demolition project waste generation rate by utilising available data, including waste disposal truck size and number, and waste volume and composition. This method is proposed as a less burdensome and more broadly applicable alternative, in contrast to waste estimation by on-site hand sorting and weighing. The developed method is applied to 11 projects across Malaysia as the case study. This study quantifies waste generation rate and illustrates the construction method in influencing the waste generation rate, estimating that the conventional construction method has a waste generation rate of 9.88 t 100 m(-2), the mixed-construction method has a waste generation rate of 3.29 t 100 m(-2), and demolition projects have a waste generation rate of 104.28 t 100 m(-2).
Matched MeSH terms: Waste Products/statistics & numerical data
In this work, two natural sources, including pomegranate peel extract and cochineal dye were employed for the synthesis of silver nanoparticles. The natural silver complex from pomegranate peel extract resulted in nano-sized structures through solution-phase method, but this method was not efficient for cochineal dye-silver precursor and the as-formed products were highly agglomerated. Therefore, an alternative facile solid-state approach was investigated as for both natural precursors and the results showed successful production of well-dispersed nanoparticles with narrow size distribution for cochineal dye-silver precursor. The products were characterized by X-ray diffraction (XRD), Scanning Electron Microscopy (SEM), Energy dispersive X-ray microanalysis (EDX), and Transmission Electron Microscopy (TEM).
A screening program searching for indigenous microbial control agents of mosquitos in Malaysia is initiated since 1987 and to date at least 20 isolates of mosquitocidal Bacillus thuringiensis serotypes have been obtained. Preliminary field evaluation of several isolates indicated that they are highly effective in the control of medically important mosquito species. For operational purposes, there is an urgent need to produce this agent utilizing cheap and locally available wastes through fermentation biotechnology. Fermentation studies in shake-flasks containing standard nutrient broth and soya bean waste, respectively, indicate that it takes about 37 hours for a Malaysian isolate of B. thuringiensis serotype H-14 to mature. In the grated coconut waste, fishmeal and rice bran, the bacteria took 28 hours, 26 hours and 126 hours respectively to mature. The endotoxin was harvested from the standard nutrient broth at 55 hours and at 50 hours from soybean, grated coconut waste and fishmeal. The endotoxin could only be harvested 150 hours after inoculation from rice bran medium. However, no bacterial growth was detected in palm oil effluent. In terms of endotoxin and biomass production, fishmeal appears to be a suitable medium. Variations in the pH of the fermenting media were also noted.
The efficacy of three insecticides, fipronil 3G, lambda-cyhalothrin 10%CS, and sumithion 50EC were evaluated against the dengue vector Aedes albopictus in discarded tires in Kuala Lumpur, Malaysia. The dosage given for each insecticide was 0.01 g of active ingredient/m2. Fipronil 3G was the most effective larvicide with a residual activity of up to two weeks, causing 88% mortality in Aedes albopictus. Lambda-cyhalothrin 10%CS was effective for one week causing 92% larval mortality and two weeks with 63% larval mortality. Sumithion 50EC had a residual efficacy of one week with 79% larval mortality.
The present study was aimed to evaluate the suitability of agro-wastes and crude vegetable oils for the cost-effective production of poly-β-hydroxybutyrate (PHB), to evaluate growth kinetics and PHB production in Alcaligenes faecalis RZS4 and Pseudomonas sp. RZS1 with these carbon substrates and to study the biodegradation of PHB accumulated by these cultures. Alcaligenes faecalis RZS4 and Pseudomonas sp. RZS1 accumulates higher amounts of PHB corn (79.90% of dry cell mass) and rice straw (66.22% of dry cell mass) medium respectively. The kinetic model suggests that the Pseudomonas sp. RZS1 follows the Monod model more closely than A. faecalis RZS4. Both the cultures degrade their PHB extract under the influence of PHB depolymerase. Corn waste and rice straw appear as the best and cost-effective substrates for the sustainable production of PHB from Alcaligenes faecalis RZS4 and Pseudomonas sp. RZS1. The biopolymer accumulated by these organisms is biodegradable in nature. The agro-wastes and crude vegetable oils are good and low-cost sources of nutrients for the growth and production of PHB and other metabolites. Their use would lower the production cost of PHB and the low-cost production will reduce the sailing price of PHB-based products. This would promote the large-scale commercialization and popularization of PHB as an ecofriendly bioplastic/biopolymer.