Displaying publications 61 - 80 of 144 in total

Abstract:
Sort:
  1. Occupational risk assessment: review of wooden scaffold board application in Malaysian oil and gas industry
    Mohd Jamil Abdul Wahab, Noor Azrieda Abd Rashid, Salmiah Ujang, Choon LS
    Sains Malaysiana, 2016;45:1139-1147.
    Timber scaffold boards have been widely utilised in the offshore construction industry. However, technical specifications
    and inspection procedure for the application of scaffold boards from a wood material were inadequate. In the development
    of the standard requirements, evaluation of actual engineering practices could indicate the level of workplace safety. A
    study was conducted to identify risk and safety measures concerning the use of timber scaffold boards in construction.
    This article discusses on the occupational risks and ergonomics issues of the scaffolding application based on the physical
    and mechanical conditions of tropical timber scaffold boards extracted from offshore oil and gas rigs. The boards were
    exposed to a seasonal climate of East Coast monsoon of South China Sea between November and February. The scaffolding
    application extended up to 20 m directly above the ocean surface and some boards were completely immersed below
    the ocean surface particularly during elevated tidal waves. Some of the boards were installed as the on-deck platforms.
    Forty scaffold boards fabricated from tropical timber species were evaluated. Physical characteristics of the boards
    were described by natural and man-made factors. A three-point bending test was conducted to determine the maximum
    load capacity of each board and the mode of fracture was evaluated. Timber identification test was conducted to identify
    the groups of the timber being used. The microscopic observation confirmed the presence of hyphae which indicated the
    biological deterioration has happened in some of the boards. Occupational risks were summarised based on the results
    of the physical and mechanical assessments
    Matched MeSH terms: Wood
  2. Fulltext Scavenging of caffeine from aqueous medium through optimized H3PO4-activated Acacia mangium wood activated carbon: Statistical data of optimization
    Danish M, Birnbach J, Mohamad Ibrahim MN, Hashim R
    Data Brief, 2020 Feb;28:105045.
    PMID: 31921950 DOI: 10.1016/j.dib.2019.105045
    The optimization data presented here are part of the study planned to remove the caffeine from aqueous solution through the large surface area optimized H3PO4-activated Acacia mangium wood activated carbon (OAMW-AC). The maximum adsorption capacity of the OAMW-AC for caffeine adsorption was achieved (30.3 mg/g) through optimized independent variables such as, OAMW-AC dosage (3.0 g/L), initial caffeine concentration (100 mg/L), contact time (60 min), and solution pH (7.7). The adsorption capacity of OAMW-AC was optimized with the help of rotatable central composite design of response surface methodology. Under the stated optimized conditions for maximum adsorption capacity, the removal efficiency was calculated to be 93%. The statistical significance of the data set was tested through the analysis of variance (ANOVA) study. Data confirmed the statistical model for caffeine adsorption was significant. The regression coefficient (R2) of curve fitting through the quadratic model was found to be 0.9832, and the adjusted regression coefficient was observed to be 0.9675.
    Matched MeSH terms: Wood
  3. Fulltext A Review on Citric Acid as Green Modifying Agent and Binder for Wood
    Lee SH, Md Tahir P, Lum WC, Tan LP, Bawon P, Park BD, et al.
    Polymers (Basel), 2020 Jul 29;12(8).
    PMID: 32751175 DOI: 10.3390/polym12081692
    Citric acid (CA) can be found naturally in fruits and vegetables, particularly citrus fruit. CA is widely used in many fields but its usage as a green modifying agent and binder for wood is barely addressed. Esterification is one of the most common chemical reactions applied in wood modification. CA contains three carboxyl groups, making it possible to attain at least two esterification reactions that are required for crosslinking when reacting with the hydroxyl groups of the cell wall polymers. In addition, the reaction could form ester linkages to bring adhesivity and good bonding characteristics, and therefore CA could be used as wood binder too. This paper presents a review concerning the usage of CA as a wood modifying agent and binder. For wood modification, the reaction mechanism between wood and CA and the pros and cons of using CA are discussed. CA and its combination with various reactants and their respective optimum parameters are also compiled in this paper. As for the major wood bonding component, the bonding mechanism and types of wood composites bonded with CA are presented. The best working conditions for the CA in the fabrication of wood-based panels are discussed. In addition, the environmental impacts and future outlook of CA-treated wood and bonded composite are also considered.
    Matched MeSH terms: Wood
  4. The impact of nature exposure on body image and happiness: an experience sampling study
    Stieger S, Aichinger I, Swami V
    Int J Environ Health Res, 2020 Aug 10.
    PMID: 32777941 DOI: 10.1080/09603123.2020.1803805
    Exposure to nature is associated with improved psychological well-being and positive body image. Here, we examined whether everyday exposure to natural environments is associated with state body image outcomes (and, for comparative reasons, state happiness) using an experience sampling method. One-hundred-and-seven participants completed a 30-day experience sampling phase in which they reported their state body image (body weight, body shape, and physical appearance satisfaction), state happiness, and features of the surrounding environment (total = 6,025 responses) at three random time-points each day. Results indicated that being outdoors was associated with significantly higher state body image on all three indicators, but effect sizes were lower compared to effects on state happiness. Specific environment type was also important, with blue-spaces and wood- and grasslands, respectively, having stronger effects than other environments. These results provide evidence that everyday exposure to natural environments is associated with more positive state body image and greater happiness.
    Matched MeSH terms: Wood
  5. Molecular identification and phylogeny of Armillaria isolates from South America and Indo-Malaysia
    Coetzee MP, Wingfield BD, Bloomer P, Ridley GS, Wingfield MJ
    Mycologia, 2003 Mar-Apr;95(2):285-93.
    PMID: 21156614
    Armillaria root rot is a serious disease, chiefly of woody plants, caused by many species of Armillaria that occur in temperate, tropical and subtropical regions of the world. Very little is known about Armillaria in South America and Southeast Asia, although Armillaria root rot is well known in these areas. In this study, we consider previously unidentified isolates collected from trees with symptoms of Armillaria root rot in Chile, Indonesia and Malaysia. In addition, isolates from basidiocarps resembling A. novae-zelandiae and A. limonea, originating from Chile and Argentina, respectively, were included in this study because their true identity has been uncertain. All isolates in this study were compared, based on their similarity in ITS sequences with previously sequenced Armillaria species, and their phylogenetic relationship with species from the Southern Hemisphere was considered. ITS sequence data for Armillaria also were compared with those available at GenBank. Parsimony and distance analyses were conducted to determine the phylogenetic relationships between the unknown isolates and the species that showed high ITS sequence similarity. In addition, IGS-1 sequence data were obtained for some of the species to validate the trees obtained from the ITS data set. Results of this study showed that the ITS sequences of the isolates obtained from basidiocarps resembling A. novae-zelandiae are most similar to those for this species. ITS sequences for isolates from Indonesia and Malaysia had the highest similarity to A. novae-zelandiae but were phylogenetically separated from this species. Isolates from Chile, for which basidiocarps were not found, were similar in their ITS and IGS-1 sequences to the isolate from Argentina that resembled A. limonea. These isolates, however, had the highest ITS and IGS-1 sequence similarity to authentic isolates of A. luteobubalina and were phylogenetically more closely related to this species than to A. limonea.
    Matched MeSH terms: Wood
  6. Fulltext Mechanical properties of wood-wool cement composite board manufactured using selected Malaysian fast grown timber species
    Ahmad, Z., Wee, L.S., Fauzi, M.A.
    ASM Science Journal, 2011;5(1):27-35.
    MyJurnal
    This paper reports the mechanical properties of cement composite boards made using wood-wool from a lesser known Malaysian timber species. A total of 108 specimens were fabricated using Portland cement (Type I) and wood-wool from Kelampayan (Neolamarckia cadamba). The cement to wood ratio of the specimens was 2 to 1 by weight. The aim of the study was to determine the density; flexural, compressive and tensile strength of wood-wool cement composite boards (WWCCB) by studying boards with wood-wool sized 1.5 mm, 2.5 mm and 3.5 mm and board thickness 25 mm, 50 mm and 75mm. The physical and mechanical properties of the boards were evaluated according to ASTM D 1037-96a (Standard testing method for evaluating properties of wood-based fibre and particle panel materials) and MS934:1986. Results showed that mechanical properties of WWCCB were greatly influenced by the density; as the density decreased, the mechanical strengths also decreased. However, the strength properties of the composite boards did not display a similar trend when subjected to different types of loading conditions. The compressive strength increased with thicker boards (50 mm and 75 mm) but the modulus of elasticity and modulus of rupture declined as the thickness of the board was increased.
    Matched MeSH terms: Wood
  7. Fulltext Production of carbon dioxide using direct pyrolysis-combustion from Aquilariella Malaccensis or karas woods under argon atmosphere
    Noraishah Othman, Siti Kartom Kamarudin, Muhd Noor Md Yunus, Abd. Halim Shamsuddin, Siti Rozaimah, Zahirah Yaakob
    Pertanika Journal of Science & Technology, 2009;17(2):-.
    MyJurnal
    The production of carbon dioxide from Karas woods under argon atmosphere was investigated using a direct pyrolysis-combustion approach. Direct burning was used in this study, using argon for yrolysis and oxygen during combustion to look at the yield of carbon dioxide, produced at different parameters, such as the temperature, retention time and flow rate of argon, as the carrier gas. In this study, a new methodology, 23 response surface central composite design was successfully employed for the experimental design and analysis of results. Central composite experimental design and response surface method were utilized to determine the best operating condition for a maximum carbon dioxide production. Appropriate predictable empirical linear model was developed by incorporating interaction effects of all the variables involved. The results of the analysis revealed that linear equation models fitted well with the experimental for carbon dioxide yield. Nevertheless, the R-Squared obtained using the direct pyrolysis-combustion was 0.7118, indicating that the regression line was not at the best-fitted line.
    Matched MeSH terms: Wood
  8. Fulltext High resolution images of resin structure in agarwood by means of sem and micro-CT
    Khairiah Yazid @ Khalid, Roslan Yahya, Nadira Kamarudini, Mohd. Zaid Abdullah, Mohd Ashhar Khalid, Abdul Aziz Mohamed
    Jurnal Sains Nuklear Malaysia, 2012;24(2):42-49.
    MyJurnal
    Detection and analysis of resin is particularly significant since the commercial value of agarwood is related to the quantity of resins that are present. This article explores the potential of a scanning electron microscope in combination with new non-destructive 3D visualization technique, X-ray micro-computed tomography, as imaging tools to visualize micro-structure resin in agarwood. These techniques were used to compare two samples of agarwood chips: high grade and low grade. From the results, it can be concluded that a wood cell filled with resin deposit have a higher attenuation. It can be shown that the combination of scanning electron microscopy and micro-CT can offer high resolution images concerning the localization and structure of resin inside Agarwood. While the second allows the 3D investigation of internal structure of agarwood, the first technique can provide details 2D morphological information. These imaging techniques, although sophisticated can be used for standard development especially in grading of agarwoodlbr commercial activities.
    Matched MeSH terms: Wood
  9. Fulltext Properties of Gliricidia wood (Gliricidia sepium) intercropped with cocoa (Theobroma cocoa) in Malaysia
    Mohd Helmy Ibrahim, Mohd Nazip Suratman, Razali Abd Kader
    Scientific Research Journal, 2014;11(1):0-0.
    MyJurnal
    Trees planted from agroforestry practices can become valuable resources in meeting the wood requirements of many nations. Gliricidia sepium is an exotic species introduced to the agricultural sector in Malaysia mainly for providing shade for cocoa and coffee plantations. This study investigates its wood physical properties (specific gravity and moisture content) and fibre morphology (length, lumen diameter and cell wall thickness) of G.sepium at three intervals according to age groups (three, five and seven years of ages). Specific gravity (0.72) was significantly higher at seven years of age as compared to five (0.41) and three (0.35) years age group with a mean of 0.43 (p0.05). Mean moisture content was 58.3 % with no significant difference existing between the tree age groups. fibre diameter (22.4 m) was significantly lower (p0.05) for the trees which were three years of age when compared to five and seven years age groups (26.6 m and 24.7 m), respectively. Means of fibre length, lumen diameter and cell wall thickness was 0.83 m, 18.3 m, and 6.2 m, respectively, with no significant differences detected between trees in all age groups in this study. Further calculation on the coefficient of suppleness and runkel ratio suggest that wood from G. sepium may have the potential for insulation board manufacture and paper making. However, future studies should experiment the utilization of this species for these products to determine its full potential.
    Matched MeSH terms: Wood
  10. Fulltext Influence of microfibril angle on the thermal and dynamic-mechanical properties of Acacia mangium wood using x-ray diffraction and dynamicsmechanical test
    Tabet, Tamer A., Wajir, Julynnie, Fauziah Abdul Aziz
    Journal of Nuclear and Related Technologies, 2009;2009(1):0-0.
    MyJurnal
    The term microfibril angle, MFA in wood science refers to the angle between the direction of the helical windings of cellulose microfibrils in the secondary cell wall, S2 layer of fibres and tracheids and the long axis of the cell. In this study, the mean MFA of the cell walls were determined for thin samples of thickness 200.0 µm from pith and outwards, for eight ages of Acacia mangium wood. The determination of MFA was based on a diffraction pattern arising from cellulose crystal planes of the type 002 generated by x-ray diffraction and recorded using an electronic detector. The results show an inversely relationship between MFA and age of tree in Acacia mangium wood. MFA decreased from 26.13° at age 3 year-old to 0.20° at tree of age 15 year-old for the pith region. The most significant drop occurred from 16.14° at age 7 yearold to 11.30° at age 9 year-old. An inversely relationship between MFA and storage modulus E’ was evidence in Acacia mangium at age 10-year-old. The results showed that about 76.22% variation of loss modulus E” was attributed to the MFA, while about 66.4% of the variation of glass transition Tg was explained by MFA under the same experimental conditions.
    Matched MeSH terms: Wood
  11. Fulltext Attenuation coefficients of Rhizophora spp. in the 11.22 to 28.43 keV photon energy range
    Sabar Bauk, Abd. Aziz Tajuddin
    Journal of Nuclear and Related Technologies, 2008;2008(1):11-19.
    MyJurnal
    The linear and the mass attenuation coefficients of Rhizophora spp. wood in the photon energy range of 11.22 - 28.43 keV were determined. This was done by studying the attenuation of x-ray fluorescent (XRF) photons from selenium, molybdenum, silver and tin targets. Both the Kα and Kβ peaks were utilised. The results were compared with theoretical values for average breast tissues for youngage, middle-age and old-age groups calculated by using a XCOM computer programme. The mass attenuation coefficient of Rhizophora spp. was found to be close to that of the calculated young-age breast in this photon energy range.
    Matched MeSH terms: Wood
  12. Fulltext Effects of process parameters on the production of carbon dioxide from karas woods for radiocarbon dating application using integrated pyrolysis-combustion
    Noraishah Othman, Muhd Noor Md Yunus, Siti Kartom Kamarudin, Abd Halim Shamsuddin, Siti Rozaimah, Zahirah Yaakob
    Journal of Nuclear and Related Technologies, 2008;2008(1):53-63.
    MyJurnal
    Production of carbon dioxide from degraded woods especially Karas or Aquilariella Malaccensis using integrated pyrolysis-combustion is important for radiocarbon dating application. The effects of pyrolysis temperatures (300-400 0 C), retention times (20-35 minutes) and flow rates of argon (400- 1000 ml/min) on the production of carbon dioxide were studied. The experiments were arranged according to a 2 3 response surface central composite statistical design (CSD). This response surface methodology (RSM) was used to assess factor interactions and empirical models regarding carbon dioxide yield. The optimized yield of carbon dioxide was 82.57% for Karas and the optimum reaction conditions are 300 0 C of pyrolysis temperature, 20 minutes retention time and 982ml/min flow rates of argon. Scanning electron microscope (SEM) and X-ray Diffraction (XRD) were conducted to assess the morphological characteristics of the woods and to look at the potential crystalline structure produced after the process took place, respectively.
    Matched MeSH terms: Wood
  13. Fulltext The Role of Zinc Chloride in Enhancing Mechanical, Thermal and Electrical Performance of Ethylene Vinyl Acetate/Carbonized Wood Fiber Conductive Composite
    Mohd Pisal MH, Osman AF, Jin TS, Rahman RA, Alrashdi AA, Masa A
    Polymers (Basel), 2021 Feb 17;13(4).
    PMID: 33671304 DOI: 10.3390/polym13040600
    Carbonized natural filler can offer the production of low cost composites with an eco-friendliness value. The evolving field of electronics encourages the exploration of more functions and potential for carbonized natural filler, such as by modifying its surface chemistry. In this work, we have performed surface modification on carbonized wood fiber (CWF) prior to it being used as filler in the ethylene vinyl acetate (EVA) composite system. Zinc chloride (ZnCl2) with various contents (2 to 8 wt%) was used to surface modify the CWF and the effects of ZnCl2 composition on the surface morphology and chemistry of the CWF filler were investigated. Furthermore, the absorptive, mechanical, thermal, and electrical properties of the EVA composites containing CWF-ZnCl2 were also analyzed. SEM images indicated changes in the morphology of the CWF while FTIR analysis proved the presence of ZnCl2 functional groups in the CWF. EVA composites incorporating the CWF-ZnCl2 showed superior mechanical, thermal and electrical properties compared to the ones containing the CWF. The optimum content of ZnCl2 was found to be 6 wt%. Surface modification raised the electrical conductivity of the EVA/CWF composite through the development of conductive deposits in the porous structure of the CWF as a channel for ionic and electronic transfer between the CWF and EVA matrix.
    Matched MeSH terms: Wood
  14. Fulltext Dosimetric study of Rhizophora Spp. particle board using Gafchromic XRQA2 film
    A. N. Azahari, N. D.M Yusob, H.A. Saidun, N.K.Y Ali, R. Abdullah, R. Hashim, et al.
    Malaysian Journal of Medicine and Health Sciences, 2020;16(102):46-50.
    MyJurnal
    Introduction: Various phantom with varied materials has been proposed to replace the human body. Besides, there is always a demand to use the local material as a phantom material, which is readily available and inexpensive. Wood is usually preferred because it is multifunction, environmentally friendly, low in toxic, inexpensive, as well as easy to use and prepare. Previous studies have found that Rhizophora spp. is a suitable natural source material and has been suggested due to its comparable dosimetric properties to commercial phantom. Methods: In this study, fabricated Rhizophora spp. particleboards phantom was opted as a solid-equivalent phantom medium at low energy photon beams using Gafchromic film x-ray quality assurance 2 (XRQA2). Additionally, the characteristics of XRQA2 film in the diagnostic energy range were generated. Results: Interestingly, the density of the fabricated Rhizophora spp particleboards was observed to have the same density with the water equivalent material (ρ= 1.00 g.cm-3) and has shown to have loosened agreement with PDD of water phantom at approximately 25% of the dose error. Also, further analysis using XRQA 2 film showed that energy was independent at different ranges. Conclusion: The analysis of fabricated Rhizophora spp particleboards undertaken here has extended our knowledge of the possibility of man- ufacturing cost-effective water equivalent phantom by using binder-less particleboard from Rhizophora spp. There- fore, a definite need for smaller interspacing particles should be considered to elevate the potential of Rhizophora spp particle boards as water equivalent materials.
    Matched MeSH terms: Wood
  15. Fulltext Application strategies by selective medium treated with entomopathogenic bacteria Serratia marcescens and Pseudomonas aeruginosa as potential biocontrol against Coptotermes curvignathus
    Chin KL, H'ng PS, Lee CL, Wong WZ, Go WZ, Khoo PS, et al.
    R Soc Open Sci, 2021 Apr 14;8(4):201311.
    PMID: 33996113 DOI: 10.1098/rsos.201311
    The success of microbial termiticides in controlling termites depends on the ability of microbes to grow in different media and the functionality of the microbes as a resistant barrier or toxic bait. This study was conducted to understand the mortality rate and behaviour changes of the subterranean termite Coptotermes curvignathus Holmgren introduced with different concentrations of Serratia marcescens strain LGMS 1 and Pseudomonas aeruginosa strain LGMS 3 using wood and soil as bacterial transfer medium. In general, higher concentration of bacteria in soil caused a reduction in tunnelling activity and wood consumption and an increase in mortality. However, application on wood revealed a different outcome. Wood treated with S. marcescens of 106 CFU ml-1 concentration proved to be more efficient as bait than higher concentration applications as it caused a high mortality rate while still highly palatable for termites. Wood or soil treated with S. marcescens concentration higher than 109 CFU ml-1 creates a high toxicity and repellent barrier for termites. Pseudomonas aeruginosa of 109 CFU ml-1 concentrations applied on wood served as a slow-acting toxic bait. However, the ability for S. marcescens and P. aeruginosa to survive on wood is low, which made the bait unable to retain a useful level of toxicity for a long period of time and frequent reapplication is needed.
    Matched MeSH terms: Wood
  16. Fulltext Recent trends in the intrinsic water-use efficiency of ringless rainforest trees in Borneo
    Loader NJ, Walsh RP, Robertson I, Bidin K, Ong RC, Reynolds G, et al.
    Philos Trans R Soc Lond B Biol Sci, 2011 Nov 27;366(1582):3330-9.
    PMID: 22006972 DOI: 10.1098/rstb.2011.0037
    Stable carbon isotope (δ(13)C) series were developed from analysis of sequential radial wood increments from AD 1850 to AD 2009 for four mature primary rainforest trees from the Danum and Imbak areas of Sabah, Malaysia. The aseasonal equatorial climate meant that conventional dendrochronology was not possible as the tree species investigated do not exhibit clear annual rings or dateable growth bands. Chronology was established using radiocarbon dating to model age-growth relationships and date the carbon isotopic series from which the intrinsic water-use efficiency (IWUE) was calculated. The two Eusideroxylon zwageri trees from Imbak yielded ages of their pith/central wood (±1 sigma) of 670 ± 40 and 759 ± 40 years old; the less dense Shorea johorensis and Shorea superba trees at Danum yielded ages of 240 ± 40 and 330 ± 40 years, respectively. All trees studied exhibit an increase in the IWUE since AD 1960. This reflects, in part, a response of the forest to increasing atmospheric carbon dioxide concentration. Unlike studies of some northern European trees, no clear plateau in this response was observed. A change in the IWUE implies an associated modification of the local carbon and/or hydrological cycles. To resolve these uncertainties, a shift in emphasis away from high-resolution studies towards long, well-replicated time series is proposed to develop the environmental data essential for model evaluation. Identification of old (greater than 700 years) ringless trees demonstrates their potential in assessing the impacts of climatic and atmospheric change. It also shows the scientific and applied value of a conservation policy that ensures the survival of primary forest containing particularly old trees (as in Imbak Canyon and Danum).
    Matched MeSH terms: Wood/growth & development; Wood/physiology; Wood/chemistry
  17. Development of microsatellite markers in Gonystylus bancanus (Ramin) useful for tracing and tracking of wood of this protected species
    Smulders MJ, VAN 't Westende WP, Diway B, Esselink GD, VAN DER Meer PJ, Koopman WJ
    Mol Ecol Resour, 2008 Jan;8(1):168-71.
    PMID: 21585747 DOI: 10.1111/j.1471-8286.2007.01914.x
    Ten polymorphic microsatellite markers have been developed for Gonystylus bancanus (Ramin), a protected tree species of peat swamp forests in Malaysia and Indonesia. Eight markers were also shown to be polymorphic in other Gonystylus species. The markers will enable assessing the amount of genetic variation within and among populations and the degree of population differentiation, such that donor populations can be selected for reforestation projects. They may be used for tracing and tracking of wood in the production chain, so that legal trade in this Convention on International Trade in Endangered Species of Wild Fauna and Flora-protected timber species, derived from specifically described origins, can be distinguished from illegally logged timber.
    Matched MeSH terms: Wood
  18. Lignin biodegradation and ligninolytic enzyme studies during biopulping of Acacia mangium wood chips by tropical white rot fungi
    Liew CY, Husaini A, Hussain H, Muid S, Liew KC, Roslan HA
    World J Microbiol Biotechnol, 2011 Jun;27(6):1457-68.
    PMID: 25187145 DOI: 10.1007/s11274-010-0598-x
    White rot fungi are good lignin degraders and have the potential to be used in industry. In the present work, Phellinus sp., Daedalea sp., Trametes versicolor and Pycnoporus coccineus were selected due to their relatively high ligninolytic enzyme activity, and grown on Acacia mangium wood chips under solid state fermentation. Results obtained showed that manganese peroxidase produced is far more compared to lignin peroxidase, suggesting that MnP might be the predominating enzymes causing lignin degradation in Acacia mangium wood chips. Cellulase enzyme assays showed that no significant cellulase activity was detected in the enzyme preparation of T. versicolor and Phellinus sp. This low cellulolytic activity further suggests that these two white rot strains are of more interest in lignin degradation. The results on lignin losses showed 20-30% of lignin breakdown at 60 days of biodegradation. The highest lignin loss was found in Acacia mangium biotreated with T. versicolor after 60 days and recorded 26.9%, corresponding to the percentage of their wood weight loss recorded followed by P. coccineus. In general, lignin degradation was only significant from 20 days onwards. The overall percentage of lignin weight loss was within the range of 1.02-26.90% over the biodegradation periods. Microscopic observations conducted using scanning electron microscope showed that T. versicolor, P. coccineus, Daedalea sp. and Phellinus sp. had caused lignin degradation in Acacia mangium wood chips.
    Matched MeSH terms: Wood
  19. Fulltext Isolation and identification of bacterial endophytes from pharmaceutical agarwood-producing Aquilaria species
    Bhore SJ, Preveena J, Kandasamy KI
    Pharmacognosy Res, 2013 Apr;5(2):134-7.
    PMID: 23798890 DOI: 10.4103/0974-8490.110545
    Resins and gums are used in traditional medicine and do have potential applications in pharmacy and medicine. Agarwood is the fragrant resinous wood, which is an important commodity from Aquilaria species and has been used as a sedative, analgesic, and digestive in traditional medicine. Endophytic bacteria are potentially important in producing pharmaceutical compounds found in the plants. Hence, it was important to understand which types of endophytic bacteria are associated with pharmaceutical agarwood-producing Aquilaria species.
    Matched MeSH terms: Wood
  20. Fulltext Genome analysis of Daldinia eschscholtzii strains UM 1400 and UM 1020, wood-decaying fungi isolated from human hosts
    Chan CL, Yew SM, Ngeow YF, Na SL, Lee KW, Hoh CC, et al.
    BMC Genomics, 2015 Nov 18;16:966.
    PMID: 26581579 DOI: 10.1186/s12864-015-2200-2
    BACKGROUND: Daldinia eschscholtzii is a wood-inhabiting fungus that causes wood decay under certain conditions. It has a broad host range and produces a large repertoire of potentially bioactive compounds. However, there is no extensive genome analysis on this fungal species.

    RESULTS: Two fungal isolates (UM 1400 and UM 1020) from human specimens were identified as Daldinia eschscholtzii by morphological features and ITS-based phylogenetic analysis. Both genomes were similar in size with 10,822 predicted genes in UM 1400 (35.8 Mb) and 11,120 predicted genes in UM 1020 (35.5 Mb). A total of 751 gene families were shared among both UM isolates, including gene families associated with fungus-host interactions. In the CAZyme comparative analysis, both genomes were found to contain arrays of CAZyme related to plant cell wall degradation. Genes encoding secreted peptidases were found in the genomes, which encode for the peptidases involved in the degradation of structural proteins in plant cell wall. In addition, arrays of secondary metabolite backbone genes were identified in both genomes, indicating of their potential to produce bioactive secondary metabolites. Both genomes also contained an abundance of gene encoding signaling components, with three proposed MAPK cascades involved in cell wall integrity, osmoregulation, and mating/filamentation. Besides genomic evidence for degrading capability, both isolates also harbored an array of genes encoding stress response proteins that are potentially significant for adaptation to living in the hostile environments.

    CONCLUSIONS: Our genomic studies provide further information for the biological understanding of the D. eschscholtzii and suggest that these wood-decaying fungi are also equipped for adaptation to adverse environments in the human host.

    Matched MeSH terms: Wood/cytology; Wood/metabolism*; Wood/microbiology*
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links