Displaying publications 81 - 100 of 175 in total

Abstract:
Sort:
  1. Dennis JO, Ahmed AY, Khir MH
    Sensors (Basel), 2015;15(7):16674-87.
    PMID: 26184204 DOI: 10.3390/s150716674
    This paper reports on the fabrication and characterization of a Complementary Metal Oxide Semiconductor-Microelectromechanical System (CMOS-MEMS) device with embedded microheater operated at relatively elevated temperatures (40 °C to 80 °C) for the purpose of relative humidity measurement. The sensing principle is based on the change in amplitude of the device due to adsorption or desorption of humidity on the active material layer of titanium dioxide (TiO2) nanoparticles deposited on the moving plate, which results in changes in the mass of the device. The sensor has been designed and fabricated through a standard 0.35 µm CMOS process technology and post-CMOS micromachining technique has been successfully implemented to release the MEMS structures. The sensor is operated in the dynamic mode using electrothermal actuation and the output signal measured using a piezoresistive (PZR) sensor connected in a Wheatstone bridge circuit. The output voltage of the humidity sensor increases from 0.585 mV to 30.580 mV as the humidity increases from 35% RH to 95% RH. The output voltage is found to be linear from 0.585 mV to 3.250 mV as the humidity increased from 35% RH to 60% RH, with sensitivity of 0.107 mV/% RH; and again linear from 3.250 mV to 30.580 mV as the humidity level increases from 60% RH to 95% RH, with higher sensitivity of 0.781 mV/% RH. On the other hand, the sensitivity of the humidity sensor increases linearly from 0.102 mV/% RH to 0.501 mV/% RH with increase in the temperature from 40 °C to 80 °C and a maximum hysteresis of 0.87% RH is found at a relative humidity of 80%. The sensitivity is also frequency dependent, increasing from 0.500 mV/% RH at 2 Hz to reach a maximum value of 1.634 mV/% RH at a frequency of 12 Hz, then decreasing to 1.110 mV/% RH at a frequency of 20 Hz. Finally, the CMOS-MEMS humidity sensor showed comparable response, recovery, and repeatability of measurements in three cycles as compared to a standard sensor that directly measures humidity in % RH.
    Matched MeSH terms: Humidity
  2. Shitan, Mahendran, Kok, Wei Ling
    MyJurnal
    Modelling observed meteorological elements can be useful. For instance, modelling rainfall has
    been an interest for many researchers. In a previous research, trend surface analysis was used and
    it was indicated that the residuals might spatially be correlated. When dealing with spatial data, any
    modelling technique should take spatial correlation into consideration. Hence, in this project, fitting
    of spatial regression models, with spatially correlated errors to the annual mean relative humidity
    observed in Peninsular Malaysia, is illustrated. The data used in this study comprised of the annual
    mean relative humidity for the year 2000-2004, observed at twenty principal meteorological stations
    distributed throughout Peninsular Malaysia. The modelling process was done using the S-plus
    Spatial Statistics Module. A total of twelve models were considered in this study and the selection
    of the model was based on the p-value. It was found that a possible appropriate model for the
    annual mean relative humidity should include an intercept and a term of the longitude as covariate,
    together with a conditional autoregressive error structure. The significance of the coefficient of the
    covariate and spatial parameter was established using the Likelihood Ratio Test. The usefulness
    of the proposed model is that it could be used to estimate the annual mean relative humidity at
    places where observations were not recorded and also for prediction. Some other potential models
    incorporating the latitude covariate have also been proposed as viable alternatives.
    Matched MeSH terms: Humidity
  3. Musa MI, Shohaimi S, Hashim NR, Krishnarajah I
    Geospat Health, 2012 Nov;7(1):27-36.
    PMID: 23242678
    Malaria remains a major health problem in Sudan. With a population exceeding 39 million, there are around 7.5 million cases and 35,000 deaths every year. The predicted distribution of malaria derived from climate factors such as maximum and minimum temperatures, rainfall and relative humidity was compared with the actual number of malaria cases in Sudan for the period 2004 to 2010. The predictive calculations were done by fuzzy logic suitability (FLS) applied to the numerical distribution of malaria transmission based on the life cycle characteristics of the Anopheles mosquito accounting for the impact of climate factors on malaria transmission. This information is visualized as a series of maps (presented in video format) using a geographical information systems (GIS) approach. The climate factors were found to be suitable for malaria transmission in the period of May to October, whereas the actual case rates of malaria were high from June to November indicating a positive correlation. While comparisons between the prediction model for June and the case rate model for July did not show a high degree of association (18%), the results later in the year were better, reaching the highest level (55%) for October prediction and November case rate.
    Matched MeSH terms: Humidity
  4. Intan Sakinah MA, Suzianti IV, Latiffah Z
    Plant Dis, 2013 Jul;97(7):991.
    PMID: 30722542 DOI: 10.1094/PDIS-10-12-0985-PDN
    Banana is the second largest cultivated fruit crop in Malaysia, and is cultivated for both the domestic market and also for export. Anthranose is a well-known postharvest disease of banana and with high potential for damaging market value, as infection commonly occurs during storage. Anthracnose symptoms were observed on several varieties of banana such as mas, berangan, awak, nangka, and rastali in the states of Perak and Penang between August and October 2011. Approximately 80% of the fruits became infected with initial symptoms characterized as brown to black spots that later became sunken lesions with orange or salmon-colored conidial masses. Infected tissues (5 × 5 mm) were surface sterilized by dipping in 1% sodium hypochlorite (NaOCl) for 3 to 5 min, rinsed with sterile distilled water, and plated onto potato dextrose agar (PDA). Direct isolation was done by transferring the conidia from conidial masses using an inoculation loop and plating onto PDA. For both methods, the PDA plates were incubated at 27 ± 1°C with cycles of 12 h light and 12 h darkness. Visible growth of mycelium was observed after 4 to 5 days of incubation. Twenty isolates with conidial masses were recovered after 7 days of incubation. The isolates produced grayish white to grayish green and grey to moss dark green colony on PDA, pale orange conidial masses, and fusiform to cylindrical and hyaline conidia with an average size of 15 to 19 × 5 to 6 μm. Appresoria were ovate to obovate, dark brown, and 9 to 15 × 7 to 12 μm and setae were present, slightly swollen at the base, with a tapered apex, and brown. The cultural and morphological characteristics of the isolates were similar to those described for C. gleosporioides (1,2,3). All the C. gloeosporioides isolates were deposited in culture collection at Plant Pathology Lab, University Sains Malaysia. For confirmation of the identity of the isolates, ITS regions were sequenced using ITS4 and ITS5 primers. The isolates were deposited in GenBank with accessions JX163228, JX163231, JX163201, JX163230, JX163215, JX163223, JX163219, JX163202, JX163225, JX163222, JX163206, JX163218, JX163208, JX163209, JX163210, JX431560, JX163212, JX163213, JX431540, and JX431562. The resulting sequences showed 99% to 100% similarity with multiple C. gloeosporioides isolates in GenBank. Pathogenicity tests were conducted using mas, berangan, awak, nangka, and rastali bananas. Fruit surfaces were sterilized with 70% ethanol and wounded using a sterile scalpel. Two inoculation techniques were performed separately: mycelia plug and conidial suspension. Mycelial disc (5 mm) and a drop of 20 μl spore suspension (106 conidia/ml) were prepared from 7-day-old culture and placed on the fruit surface. The inoculated fruits were incubated at 27 ± 1°C for 10 days at 96.1% humidity. After 3 to 4 days of inoculation, brown to black spotted lesions were observed and coalesced to become black sunken lesions. Similar anthracnose symptoms were observed on all banana varieties tested. C. gloeosporioides was reisolated from the anthracnose lesions of all the inoculated fruit in which the cultural and morphological characteristics were the same as the original isolates. To our knowledge, this is the first report of C. gloeosporioides causing anthracnose of Musa spp. in Malaysia. References: (1) P. F. Cannon et al. Mycotaxon 104:189, 2008. (2) J. E. M. Mordue. Glomerella cingulata. CMI Description of Pathogenic Fungi and Bacteria, No. 315. CAB International,1971. (3) H. Prihastuti et al. Fungal Diversity 39:89, 2009.
    Matched MeSH terms: Humidity
  5. How YF, Lee CY
    J Med Entomol, 2010 Nov;47(6):987-95.
    PMID: 21175045
    The effect of temperature and humidity on the survival and water loss of the tropical bed bug, Cimex hemipterus (F.), was studied using two field-collected strains. Insects were exposed to temperatures ranging from 20 to 45 degrees C and relative humidities (RHs) of 33, 75, and 100%. C. hemipterus survived longest under the interaction of low temperature (20 degrees C) and high RH (75-100%). Survival and water loss were significantly affected (P < 0.01) by temperature and RH (either singly, or in interaction). Strain and sex significantly (P < 0.01) influenced bed bug survival, but not on water loss. Eggs, first instars, and adults reached their upper thermal lethal limit within 1 h at 39 degrees C, 44 degrees C, and 46 degrees C, respectively. The survival and water loss profiles showed that starved C. hemipterus started to die after losing 35-45% of their body weights.
    Matched MeSH terms: Humidity*
  6. Tee HS, Lee CY
    J Insect Physiol, 2015 Jun;77:45-54.
    PMID: 25921676 DOI: 10.1016/j.jinsphys.2015.04.007
    The impact of desiccation on habitat selection, foraging and survival has been characterized for many insects. However, limited information is available for parasitic wasps. In this study, water balance, relative humidity (RH) preference, and effect of humidity on survival of solitary Evania appendigaster (L.) (Hymenoptera: Evaniidae) and gregarious Aprostocetus hagenowii (Ratzeburg) (Hymenoptera: Eulophidae) were examined. These species are both oothecal parasitoids of the American cockroach Periplaneta americana (L.) (Dictyoptera: Blattidae). E. appendigaster had significantly higher cuticular permeability (CP) and a lower surface area to volume ratio but a similar percentage of total body water content compared to A. hagenowii. No differences in these attributes were found between sexes of each parasitoid species. The percentage of total body water loss rates among E. appendigaster males and females and A. hagenowii females were similar but significantly lower than that of A. hagenowii males. All parasitoids except E. appendigaster males exhibited reduced survival times as the RH of their enclosure decreased from 87% to 38%, but this phenomenon did not occur when parasitoids were given a sugar solution. In environmental chambers with a 44-87% RH gradient, both sexes of E. appendigaster resided significantly more often in the 87% RH chamber than in the 44% RH chamber. For A. hagenowii, females preferred both the driest and the wettest chambers and males preferred the driest ones. These results demonstrate the water balance profile and its relationship to life history traits and differential responses to RH in these competing parasitoid wasps, suggesting the role of physiological and behavioral adaptations in shaping their ecological niche.
    Matched MeSH terms: Humidity
  7. Hu J, Neoh KB, Appel AG, Lee CY
    PMID: 22085890 DOI: 10.1016/j.cbpa.2011.10.028
    The foraging patterns of termites are strongly related to physiological limits in overcoming desiccation stress. In this study, we examined moisture preferences and physiological characteristics of Macrotermes carbonarius (Hagen) and M. gilvus (Hagen) as both exhibit conspicuous patterns of foraging activity. Despite both species showing no significant differences in calculated cuticular permeability, and percentage of total body water, they differed greatly in rate of water loss and surface area to volume ratio. For example, M. carbonarius which had a lower surface area to volume ratio (29.26-53.66) showed lower rate of water loss and percentage of total body water loss. This also resulted in higher LT(50) when exposed to extreme conditions (≈2% RH). However, contrasting observations were made in M. gilvus that has smaller size with higher surface area to volume ratio of 40.28-69.75. It is likely that the standard equation for calculating insect surface areas is inadequate for these termite species. The trend was further supported by the result of a moisture preference bioassay that indicated M. carbonarius had a broader range of moisture preference (between 5% and 20%) than M. gilvus which had a relatively narrow moisture preference (only 20%). These results explain why M. carbonarius can tolerate desiccation stress for a longer period foraging above-ground in the open air; while M. gilvus only forages below ground or concealed within foraging mud tubes.
    Matched MeSH terms: Humidity
  8. Jung D, Kim YB, Lee JB, Muhamed AMC, Lee JY
    Eur J Appl Physiol, 2018 Dec;118(12):2655-2667.
    PMID: 30209544 DOI: 10.1007/s00421-018-3988-7
    PURPOSE: We investigated the effects of humidity on regional sweating secretion and active sweat gland density on the scalp during passive heating in hot environments.

    METHODS: Eight male subjects shaved their heads prior to expose to dry (30%RH; H30%) and humid (85%RH; H85%) conditions at an air temperature of 32 °C. Total sweat rate, local sweat rates (frontal, vertex, temporal, and occipital regions), active sweat glands on the scalp (2 frontal, 2 parietal, 2 temporal, 1 occipital, and 1 vertex), and rectal and skin temperatures were measured during leg immersion in 42 °C water for 60 min.

    RESULTS: (1) Total sweat rates were greater for H30% (179.4 ± 35.6 g h-1) than for H85% (148.1 ± 27.2 g h-1) (P 

    Matched MeSH terms: Humidity*
  9. Mohd Mahathir Suhaimi Shamsuri, Leman, A.M.
    MyJurnal
    Indoor pollution increasingly becomes a public concern. These concerns are related to energy efficiency in a
    building. There are various ways in which it can ensure energy conservation can be achieved, including superinsulation
    and reduced fresh air exchange. As a result, indoor air becomes stagnant and odours, thereafter contaminants of air will
    accumulate and will certainly disrupt human health. It is quite difficult to make people comfortable in a building with
    consumption of energy-saving and human health guaranteed. Indoor plants are one of the alternative solutions that
    have been studied since the last three decades. This paper intends to review the abilities of indoor plants to purify air,
    and the ways used by previous researchers to prove that indoor plants can treat the air. In general, it can be stated that
    indoor plants are able to absorb various types of volatile organic compounds (VOCs). An advantage of indoor plants
    to cure air from carcinogen gas is greatly needed for human health. Therefore, studies on indoor plants to neutralize
    the air are gaining attention. Enclosed space or chamber is often used by researchers to test the ability of indoor plants
    absorb gaseous toxins in their study; because it is easy to handle and can quickly determine the absorption rate. In the
    other hand, environmental factors such as temperature, humidity, and light are important to be taken into consideration
    during the study. As a conclusion, it can be stated that the existence of indoor plants in a building is very reasonable,
    because it can give positive impacts on human health and the total energy consumption.
    Matched MeSH terms: Humidity
  10. Veronica N, Heng PWS, Liew CV
    Mol Pharm, 2023 Feb 06;20(2):1072-1085.
    PMID: 36480246 DOI: 10.1021/acs.molpharmaceut.2c00812
    The stability of a moisture-sensitive drug in tablet formulations depends particularly on the environment's relative humidity (RH) and the products' prior exposure to moisture. This study was designed to understand drug stability in relation to the moisture interaction of the excipients, moisture history of the tablets, and RH of the environment. The stability study was performed on tablets containing acetylsalicylic acid (ASA), formulated with common pharmaceutical excipients like native maize starch, microcrystalline cellulose (MCC), partially pregelatinized maize starch (PGS), dicalcium phosphate dihydrate (DCP), lactose, and mannitol. The tablets were subjected to storage conditions with RH cycling alternating between 53% and 75%. Results were also compared to tablets stored at a constant RH of 53% or 75%. The excipients demonstrated marked differences in their interactions with moisture. They could be broadly grouped as excipients with RH-dependent moisture content (native maize starch, MCC, and PGS) and RH-independent moisture content (DCP, lactose, and mannitol). As each excipient interacted differently with moisture, degradation of ASA in the tablets depended on the excipients' ability to modulate the moisture availability for degradation. The lowest ASA degradation was observed in tablets formulated with low moisture content water-soluble excipients, such as lactose and mannitol. The impact of RH cycling on ASA stability was apparent in tablets containing native maize starch, MCC, PGS, or DCP. These findings suggested that the choice of excipients influences the effect of moisture history on drug stability. The results from studies investigating moisture interaction of excipients and drug stability are valuable to understanding the inter-relationship between excipients, moisture history, and drug stability.
    Matched MeSH terms: Humidity
  11. Ko Y, Yao KS, Chen CY, Lin CH
    Plant Dis, 2007 Dec;91(12):1684.
    PMID: 30780618 DOI: 10.1094/PDIS-91-12-1684B
    Mango (Mangifera indica L.; family Anacardiaceae) is one of the world's most important fruit crops and is widely grown in tropical and subtropical regions. Since 2001, a leaf spot disease was found in mango orchards of Taiwan. Now, the disease was observed throughout (approximately 21,000 ha) Taiwan in moderate to severe form, thus affecting the general health of mango trees and orchards. Initial symptoms were small, yellow-to-brown spots on leaves. Later, the irregularly shaped spots, ranging from a few millimeters to a few centimeters in diameter, turned white to gray and coalesced to form larger gray patches. Lesions had slightly raised dark margins. On mature lesions, numerous black acervuli, measuring 290 to 328 μm in diameter, developed on the gray necrotic areas. Single conidial isolates of the fungus were identified morphologically as Pestalotiopsis mangiferae (Henn.) Steyaert (2,3) and were consistently isolated from the diseased mango leaves on acidified (0.06% lactic acid) potato dextrose agar (PDA) medium incubated at 25 ± 1°C. Initially, the fungus grew (3 mm per day) on PDA as a white, chalky colony that subsequently turned gray after 2 weeks. Acervuli developed in culture after continuous exposure to light for 9 to 12 days at 20 to 30°C. Abundant conidia oozed from the acervulus as a creamy mass. The conidia (17.6 to 25.4 μm long and 4.8 to 7.1 μm wide) were fusiform and usually straight to slightly curved with four septa. Three median cells were olivaceous and larger than the hyaline apical and basal cells. The apical cells bore three (rarely four) cylindrical appendages. Pathogenicity tests were conducted with either 3-day-old mycelial discs or conidial suspension (105 conidia per ml) obtained from 8- to 10-day-old cultures. Four leaves on each of 10 trees were inoculated. Before inoculation, the leaves were washed with a mild detergent, rinsed with tap water, and then surface sterilized with 70% ethanol. Leaves were wounded with a needle and exposed to either a 5-mm mycelial disc or 0.2 ml of the spore suspension. The inoculated areas were wrapped with cotton pads saturated with sterile water and the leaves were covered with polyethylene bags for 3 days to maintain high relative humidity. Wounded leaves inoculated with PDA discs alone served as controls. The symptoms described above were observed on all inoculated leaves, whereas uninoculated leaves remained completely free from symptoms. Reisolation from the inoculated leaves consistently yielded P. mangiferae, thus fulfilling Koch's postulates. Gray leaf spot is a common disease of mangos in the tropics and is widely distributed in Africa and Asia (1-3); however, to our knowledge, this is the first report of gray leaf spot disease affecting mango in Taiwan. References: (1) T. K. Lim and K. C. Khoo. Diseases and Disorders of Mango in Malaysia. Tropical Press. Malaysia, 1985. (2) J. E. M. Mordue. No. 676 in: CMI Descriptions of Pathogenic Fungi and Bacteria. Surrey, England, 1980. (3) R. C. Ploetz et al. Compendium of Tropical Fruit Diseases. The American Phytopathological Society. St. Paul, MN, 1994.
    Matched MeSH terms: Humidity
  12. Ch'ng TW, Mosavi SA, Noor Azimah AA, Azlan NZ, Azhany Y, Liza-Sharmini AT
    Med J Malaysia, 2013 Oct;68(5):410-4.
    PMID: 24632871 MyJurnal
    INTRODUCTION: Acute angle closure (AAC) without prompt treatment may lead to optic neuropathy. Environmental factor such as climate change may precipitate pupillary block, the possible mechanism of AAC.

    OBJECTIVE: To determine the association of northeast monsoon and incidence of AAC in Malaysia.

    MATERIALS AND METHODS: A retrospective study was conducted on AAC patients admitted to two main tertiary hospitals in Kelantan, Malaysia between January 2001 and December 2011. The cumulative number of rainy day, amount of rain, mean cloud cover and 24 hours mean humidity at the estimated day of attack were obtained from the Department of Meteorology, Malaysia.

    RESULTS: A total 73 cases of AAC were admitted with mean duration of 4.1SD 2.0 days. More than half have previous history of possibility of AAC. There was higher incidence of AAC during the northeast monsoon (October to March). There was also significant correlation of number of rainy day (r=0.718, p<0.001), amount of rain (r=0.587, p<0.001), cloud cover (r=0.637, p<0.001), mean daily global radiation (r=- 0.596, P<0.001), 24 hours mean temperature (r=-0.298, p=0.015) and 24 hours mean humidity (r=0.508, p<0.001) with cumulative number of admission for AAC for 12 calendar months.

    CONCLUSION: Higher incidence of AAC during northeast monsoon suggested the effect of climate as the potential risk factor. Prompt treatment to arrest pupillary block and reduction of the intraocular pressure is important to prevent potential glaucomatous damage. Public awareness of AAC and accessibility to treatment should be part of preparation to face the effect of northeast monsoon.
    Matched MeSH terms: Humidity
  13. Levesque DL, Tuen AA, Lovegrove BG
    PMID: 29623412 DOI: 10.1007/s00360-018-1160-7
    Much of our knowledge of the thermoregulation of endotherms has been obtained from species inhabiting cold and temperate climates, our knowledge of the thermoregulatory physiology of tropical endotherms is scarce. We studied the thermoregulatory physiology of a small, tropical mammal, the large treeshrew (Tupaia tana, Order Scandentia) by recording the body temperatures of free-ranging individuals, and by measuring the resting metabolic rates of wild individuals held temporarily in captivity. The amplitude of daily body temperature (~ 4 °C) was higher in treeshrews than in many homeothermic eutherian mammals; a consequence of high active-phase body temperatures (~ 40 °C), and relatively low rest-phase body temperatures (~ 36 °C). We hypothesized that high body temperatures enable T. tana to maintain a suitable gradient between ambient and body temperature to allow for passive heat dissipation, important in high-humidity environments where opportunities for evaporative cooling are rare. Whether this thermoregulatory phenotype is unique to Scandentians, or whether other warm-climate diurnal small mammals share similar thermoregulatory characteristics, is currently unknown.
    Matched MeSH terms: Humidity
  14. Kian Tsong Ho, Mohd Zainal Abidin Ab Kadir, Mahdi Izadi
    MyJurnal
    In this paper, cap and pin porcelain insulator was studied under an environment with different levels
    of humidity. The electric field strength and voltage distribution profile along the insulator string was
    simulated using a computational software package. In this study, ANSYS Maxwell based on the Finite
    Element Method (FEM) was used to simulate the short standard insulator string. The short standard
    insulator string was modelled as a five-unit cap and pin porcelain insulator that was stacked according
    to the IEC 60383 standard. Different humidity levels measured using relative humidity is applied to
    the insulator. From this simulation, the locations within the insulator under high electric field stress are
    identified when different humidity is applied.
    Matched MeSH terms: Humidity
  15. Nazatul Syadia Zainordin, Nor Azam Ramli, Maher Elbayoumi
    Sains Malaysiana, 2017;46:197-207.
    ir quality has deteriorated in urban areas as a result of increased anthropogenic activities. Quantitative information on the influence of meteorological conditions on several pollutants in a tropical climate is still lacking. Real-time ozone (O3) and nitrogen dioxide (NO2) levels were measured nearby selected schools in Malaysia to examine the impact of meteorological factors on monitoring pollutants. The results showed the overall 10 min average concentrations of the main parameters during school holiday were 24 ppb (O3) and 33 ppb (NO2) while during school day the overall 10 min average concentrations were 26 ppb (O3) and 51 ppb (NO2). Although there are no minimum requirements for short-term exposure by MAAQG, if compared to 1 h average requirements, all concentrations were still below the suggested values. Regarding spatial distribution, a different trend in pollutant concentration among the schools was observed because of the influence of temperature (AT) and wind speed (WS). The results were verified by Pearson correlation, where significant correlations (p<0.01) were determined between air pollutants and meteorological factors, which were temperature, wind speed and relative humidity. Meanwhile, the distribution of O3 was moderately correlated with NO2. However, the results of multivariate analysis indicate that temperature and relative humidity had the most significant influence on the formation of O3. In summary, the results of this study showed that all precursors and meteorological parameters contribute to the production of O3. Hence, reducing O3 precursors, which are emitted by vehicles, is essential to lessening the exposure to O3
    Matched MeSH terms: Humidity
  16. Markus Bulus, Lim, Yaik-Wah, Malsiah Hamid
    MyJurnal
    The Climatic performance of courtyard residential buildings needs to be
    investigated if the assertion that courtyard is a microclimate modifier is to be
    accepted. Therefore, this study seeks to examine the microclimatic performance
    of two existing courtyard residential buildings with similar characteristics in
    Kafanchan-Kaduna Nigeria, -the fully enclosed courtyard residential building and
    the semi-enclosed courtyard residential building. The purpose of this research is
    to investigate their microclimatic performances in other to establish the best
    courtyard house. This study uses measurement to achieve its aim. The tool
    employed for data collection is the Hobo Weather Data Loggers (HWDL). Three
    HWDL were used to collect data in the two case-study, and the third one was
    placed in the outside area as a benchmark. Only air temperature and relative
    humidity were measured. This study revealed a tangible difference in the
    microclimatic performance of the two case-study. The fully enclosed courtyard
    residential building is seen to have air temperature difference of 1 oC to 3 oC, and
    the relative humidity difference of 4 % to 8 %. In conclusion, the fully enclosed
    courtyard house demonstrated a more favorable microclimatic performance than
    the semi-enclosed, and further simulation studies towards its optimization are
    required.
    Matched MeSH terms: Humidity
  17. Markus Bulus, Lim, Yaik-Wah, Malsiah Hamid
    MyJurnal
    Scholars have opined that the courtyard is a passive architectural design element and
    that it can act as a microclimate modifier provided that its design requirements are not
    ignored. But despite the assertions, empirical studies on the microclimatic
    performance of a fully enclosed courtyard house and the non-courtyard house seems
    to be deficient, and the assumption that the Courtyard is a passive architectural design
    element needs to be substantiated. Therefore, the purpose of this study is to
    investigate the microclimatic performance of a fully enclosed courtyard and noncourtyard
    residential buildings. The main objective is to compare their microclimatic
    performances in other to draw a conclusion on the best option. Three Hobo Weather
    Data Loggers were used to collect climatic data in the buildings, and the third one was
    situated in the outdoor area as a benchmark. The climatic variables investigated are;
    air temperature and relative humidity. The fully enclosed courtyard residential building
    is seen to have a better air temperature difference of 2 oC to 4 oC and the relative
    humidity of 2 % to 6 %. In conclusion, the fully enclosed courtyard residential building
    has confirmed a more favorable microclimatic performance, and future studies
    towards its optimization are recommended.
    Matched MeSH terms: Humidity
  18. Sudheer S, Ali A, Manickam S
    Int J Med Mushrooms, 2016;18(10):935-943.
    PMID: 27910761
    Rigorous research has been carried out regarding the cultivation of Ganoderma lucidum using different agricultural residues. Nevertheless, large-scale cultivation and the separation of active compounds of G. lucidum are still challenges for local farmers. The objective of this study was to evaluate the use of oil palm waste fibers such as empty fruit bunch fibers and mesocarp fibers as effective substrates for the growth of G. lucidum mycelia to study the possibility of solid-state cultivation and to determine the optimum conditions necessary for the growth of mycelia of this mushroom on these waste fibers. Various parameters such as temperature, pH, humidity, and carbon and nitrogen compositions required for the optimum growth of mycelia have been determined. Oil palm fibers are a vivid source of lignocellulose, and their availability in Malaysia is high compared to that of sawdust. G. lucidum is a wood-rotting fungi that can easily decay and utilize this lignocellulose biomass, a major agricultural waste in Malaysia.
    Matched MeSH terms: Humidity
  19. Willmott AGB, Hayes M, James CA, Gibson OR, Maxwell NS
    Temperature (Austin), 2019 Sep 19;7(2):178-190.
    PMID: 33015245 DOI: 10.1080/23328940.2019.1664370
    Athletes exercising in heat stress experience increased perceived fatigue acutely, however it is unknown whether heat acclimation (HA) reduces the magnitude of this perceptual response and whether different HA protocols influence the response. This study investigated sensations of fatigue following; acute exercise-heat stress; short- (5-sessions) and medium-term (10-sessions) HA; and between once- (ODHA) and twice-daily HA (TDHA) protocols. Twenty male participants (peak oxygen uptake: 3.75 ± 0.47 L·min-1) completed 10 sessions (60-min cycling at ~2 W·kg-1, 45°C/20% relative humidity) of ODHA (n = 10) or non-consecutive TDHA (n = 10). Sensations of fatigue (General, Physical, Emotional, Mental, Vigor and Total Fatigue) were assessed using the multi-dimensional fatigue scale inventory-short form pre and post session 1, 5 and 10. Heat adaptation was induced following ODHA and TDHA, with reductions in resting rectal temperature and heart rate, and increased plasma volume and sweat rate (P 
    Matched MeSH terms: Humidity
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links