Crude jatropha oil (JO) was modified to form jatropha oil-based polyol (JOL) via two steps in a chemical reaction known as epoxidation and hydroxylation. JOL was then reacted with isocyanates to produce JO-based polyurethane resin. In this study, two types of isocyanates, 2,4-toluene diisocyanate (2,4-TDI) and isophorone diisocyanate (IPDI) were introduced to produce JPUA-TDI and JPUA-IPDI respectively. 2,4-TDI is categorised as an aromatic isocyanate whilst IPDI is known as a cycloaliphatic isocyanate. Both JPUA-TDI and JPUA-IPDI were then end-capped by the acrylate functional group of 2-hydroxyethyl methacrylate (HEMA). The effects of that isocyanate structure were investigated for their physico, chemical and thermal properties. The changes of the functional groups during each synthesis step were monitored by FTIR analysis. The appearance of urethane peaks was observed at 1532 cm-1, 1718 cm-1 and 3369 cm-1 while acrylate peaks were detected at 815 cm-1 and 1663 cm-1 indicating that JPUA was successfully synthesised. It was found that the molar mass of JPUA-TDI was doubled compared to JPUA-IPDI. Each resin showed a similar degradation pattern analysed by thermal gravimetric analysis (TGA). For the mechanical properties, the JPUA-IPDI-based coating formulation exhibited a higher hardness value but poor adhesion compared to the JPUA-TDI-based coating formulation. Both types of jatropha-based polyurethane acrylate may potentially be used in an ultraviolet (UV) curing system specifically for clear coat surface applications to replace dependency on petroleum-based chemicals.
The ever-increasing demand for the finite source of oil has led oil production companies to produce and transport the produced crude oil as efficiently and economically as possible. One of the major concerns especially in waters like the South China Sea is the deposition of wax on the walls of the pipeline or wellbore, constricting and hindering the hydrocarbon flow. This is due to the low seabed temperatures, which can be below the wax appearance temperature (WAT), leading to the deposition of wax out of waxy crude oil through the molecular dispersion mechanism. Currently, many prevention and remedy methods are in place to overcome the problem, but most of the additives possess environmental threat, as most of the chemical solutions used are toxic, nonorganic, and costly. Hence, this paper aims to provide some insights into the effect of palm oil derivatives such as crude palm oil (CPO) and crude palm kernel oil (CPKO) on wax inhibition. The effect of aging time (i.e., immersion time) was also evaluated. A comparison was made between paraffin inhibition efficiency results (PIE %) obtained by CPO, CPKO, poly(ethylene-co-vinyl acetate) (EVA), and triethanolamine (TEA). It was observed that the average efficiency of 81.67% was obtained when 1% CPO was added to heavy crude oil. The wax inhibition performance reached a plateau after 1.5 h of aging time for all of the investigated samples.
In this study, a binary mixture of petroleum coke and palm kernel shell had been investigated as potential starting materials for activated carbon production. Single-stage potassium carbonate (K2CO3) activation under nitrogen (N2) atmosphere was adopted in this research study. Effect of several operating parameters that included the impregnation ratio (1-3 wt./wt.), activation temperature (600-800 °C), and dwell time (1-2 hrs) were analyzed by using the Box-Behnken experimental design. Influence of these parameters towards activated carbon yield (Y1) and carbon dioxide (CO2) adsorption capacity at an atmospheric condition (Y2) were investigated. The optimum conditions for the activated carbon production were attained at impregnation ratio of 1.75:1, activation temperature of 680 °C, and dwell time of 1 h, with its corresponding Y1 and Y2 is 56.2 wt.% and 2.3991 mmol/g, respectively. Physicochemical properties of the pristine materials and synthesized activated carbon at the optimum conditions were analyzed in terms of their decomposition behavior, surface morphology, elemental composition, and textural characteristics. The study revealed that the blend of petroleum coke and palm kernel shell can be effectively used as the activated carbon precursors, and the experimental findings demonstrated comparable CO2 adsorption performance with commercial activated carbon as well as that in literatures.
The accumulation of conventional petroleum-based polymers has increased exponentially over the years. Therefore, algae-based biopolymer has gained interest among researchers as one of the alternative approaches in achieving a sustainable circular economy around the world. The benefits of microalgae biopolymer over other feedstock is its autotrophic complex to reduce the greenhouse gases emission, rapid growing ability with flexibility in diverse environments and its ability to compost that gives greenhouse gas credits. In contrast, this review provides a comprehensive understanding of algae-based biopolymer in the evaluation of microalgae strains, bioplastic characterization and bioplastic blending technologies. The future prospects and challenges on the algae circular bioeconomy which includes the challenges faced in circular economy, issues regard to the scale-up and operating cost of microalgae cultivation and the life cycle assessment on algal-based biopolymer were highlighted. The aim of this review is to provide insights of algae-based biopolymer towards a sustainable circular bioeconomy.
The effect of the oil-spill dispersant Corexit 9527 on egg-hatching rate of Macrobrachium rosenbergii (de Man) was studied by using an innovated flow-through bioassay technique. This bioassay method relies on the fact that M. rosenbergii fertilized eggs when detached from the mother prawn were able to hatch artificially. The flow-through system generated a stable and good water quality environment for hatching the eggs successfully. The Corexit 9527 had a pronounced effect on hatching rate of the M. rosenbergii eggs. In the control, the hatching rate of the eggs was 95.55% +/- 1.74%. However, it was reduced drastically with increasing concentrations of Corexit 9527. A 100% inhibition of egg hatchability was found when the level of Corexit 9527 was higher than 250 mg litre(-1). The EC(50) and the EC(95) values estimated by the probit method were 80.4 +/- 5.5 mg litre(-1) and 193.5 +/- 39.9 mg litre(-1) respectively (P = 0.05). The recommended safety level of Corexit 9527 for M. rosenbergii in Malaysian estuarine waters is below 40 mg litre(-1).
The biggest agricultural sector that contributes to the Malaysian economy is the oil palm industry. The effluent generated during the production of crude palm oil known as palm oil mill effluent (POME). POME undergoes anaerobic treatment that requires long retention time and produces large amount of methane that consequently contributes to global warming. In this study, an isolated bacteria was selected based on its ability to degrade kraft lignin (KL) and identified as Ochrobactrum sp. The bacteria were able to treat POME (from anaerobic pond) under the aerobic condition without addition of nutrient, resulting in a significant chemical oxygen demand (COD) removal of 71 %, removal rate of 1385 mg/l/day, and 12.3 times higher than that of the ponding system. It has also resulted in 60 % removal of ammoniacal nitrogen and 55 % of total polyphenolic after 6-day treatment period with the detection of lignocellulolytic enzymes.
In December 2009, at the UN Climate Change Conference COP 15 in Copenhagen, the Prime Minister of Malaysia, the Rt. Hon. Mohd Najib Abdul Razak, had announced that “Malaysia is adopting an indicator of a voluntary reduction of up to 40% in terms of emissions intensity of GDP by the year 2020 compared to 2005 levels. This indicator is conditional on receiving the transfer of technology and finance of adequate and effective levels from Annex 1 partners, that correspond to what is required in order to achieve this indicator”. Malaysia also needs to decouple its GDP from its current relatively high carbon-based energy demand. In trying to meet both these targets, we need to intensify our research efforts in energy-based areas. As government funding in R&D is limited as the aim is for research to be private-sector driven, and with the grim global economic scenario today, it is most unlikely that Malaysia will get any assistance financially or technologically from Annex 1 nations. It is therefore proposed that Malaysia considers implementing a dedicated carbon cess on petroleum products to fund R&D in the country. (Copied from article).
In industrial plants such as electricity generating, petroleum, chemical and petrochemical plants, pipelines are used extensively to transport liquid from one location to another. In radiation vulcanization of natural rubber latex (RVNRL) plants, pipelines are also used to transport latex to storage tank. During one of its maintenance activities, a pipeline intelligent gauge (PIG) that was used to monitor pipe integrity jammed inside the pipe causing interruption to its operation or loading activities. Sealed source technology was utilized to determine the location of jammed PIG in the pipeline. Fast neutrons from a 50 mCi Americium Beryllium (AmBe241), with energy range between 0.5 to11 MeV, were used for the study. Helium 3 (He3) detector was used to detect slow neutrons having a range of energy of 30 eV- 0.5 MeV. The investigation was carried out using neutron backscatter technique scanner. By adopting back-scattered technique, the location of jammed PIG in the pipeline has been successfully determined.
Global issues such as environmental problems and food security are currently of concern to all of us. Circular bioeconomy is a promising approach towards resolving these global issues. The production of bioenergy and biomaterials can sustain the energy-environment nexus as well as substitute the devoid of petroleum as the production feedstock, thereby contributing to a cleaner and low carbon environment. In addition, assimilation of waste into bioprocesses for the production of useful products and metabolites lead towards a sustainable circular bioeconomy. This review aims to highlight the waste biorefinery as a sustainable bio-based circular economy, and, therefore, promoting a greener environment. Several case studies on the bioprocesses utilising waste for biopolymers and bio-lipids production as well as bioprocesses incorporated with wastewater treatment are well discussed. The strategy of waste biorefinery integrated with circular bioeconomy in the perspectives of unravelling the global issues can help to tackle carbon management and greenhouse gas emissions. A waste biorefinery-circular bioeconomy strategy represents a low carbon economy by reducing greenhouse gases footprint, and holds great prospects for a sustainable and greener world.
Overconsumption of plastic goods and improper handling of petroleum-derived plastic waste have brought a plethora of negative impacts to the environment, ecosystem and human health due to its recalcitrance to degradation. These drawbacks become the main driving force behind finding biopolymers with the degradable properties. With the advancement in biopolymer research, polyhydroxyalkanoate (PHA) and poly(lacyic acid) (PLA) and its composites have been alluded to as a potential alternative to replace the petrochemical counterpart. This review highlights the current synthesis process and application of PHAs and PLA and its composites for food packaging materials and coatings. These biopolymers can be further ameliorated to enhance their applicability and are discussed by including the current commercially available packaging products. Factors influencing biodegradation are outlined in the latter part of this review. The main aim of this review article is to organize the scattered available information on various aspects of PHAs and PLA, and its composites for packaging application purposes. It is evident from a literature survey of about 140 recently published papers from the past 15 years that PLA and PHA show excellent physical properties as potential food packaging materials.
Thermoplastic starch composites have attracted significant attention due to the rise of environmental pollutions induced by the use of synthetic petroleum-based polymer materials. The degradation of traditional plastics requires an unusually long time, which may lead to high cost and secondary pollution. To solve these difficulties, more petroleum-based plastics should be substituted with sustainable bio-based plastics. Renewable and natural materials that are abundant in nature are potential candidates for a wide range of polymers, which can be used to replace their synthetic counterparts. This paper focuses on some aspects of biopolymers and their classes, providing a description of starch as a main component of biopolymers, composites, and potential applications of thermoplastics starch-based in packaging application. Currently, biopolymer composites blended with other components have exhibited several enhanced qualities. The same behavior is also observed when natural fibre is incorporated with biopolymers. However, it should be noted that the degree of compatibility between starch and other biopolymers extensively varies depending on the specific biopolymer. Although their efficacy is yet to reach the level of their fossil fuel counterparts, biopolymers have made a distinguishing mark, which will continue to inspire the creation of novel substances for many years to come.
The East Coast of Peninsular Malaysia faces the South China Sea and is vulnerable to oil pollution because of intense petroleum production activities in the area. The South China Sea is also a favored route for supertankers carrying crude oil to the Far East. Consequently, oil spills can occur, causing pollution and contamination in the surrounding areas. Residual oil spills stranded on coastal beaches usually end up as tar-balls. Elucidating the sources of tar-balls using a molecular marker approach is essential in assessing environmental impacts and perhaps settling legal liabilities for affected parties. This study utilizes a multimodal molecular marker approach through the use of diagnostic ratios of alkanes, hopanes, and polycyclic aromatic hydrocarbons (PAHs) to determine the source, distribution and weathering of tar-balls. Hopane ratios (e.g., C29/C30, and summation C31-C35/C30 ratios) were used to identify the sources of tar-balls. The weathering effects were distinguished by using alkanes, namely the unresolved complex mixture (UCM) and low molecular weight/high molecular weight (L/H) ratios. Similarly, PAHs were also used for the determination of weathering processes undergone by the tar-balls. This multimodal molecular marker gave a very strong indication of the sources of tar-balls in this study. For example, 16 out of 17 samples originated from South East Asian Crude Oil (SEACO) with one sample from Merang, Terengganu originating from North Sea Oil (Troll). The TRME-2 sample may have come from a supertanker's ballast water discharge. The second possibility is that the tar-ball may have been transported via oceanographic currents. All 'weathered' sample characterizations were based on the presence of UCM and other ratios. The multimodal molecular marker approach applied in this study has enabled us to partially understand the transport behavior of tar-balls in the marine environment and has revealed insights into the weathering process of tar-balls.
The oil palm seed production unit that generates germinated oil palm seeds is the first link in the palm oil supply chain, followed by the nursery to produce seedling, the plantation to produce fresh fruit bunches (FFB), the mill to produce crude palm oil (CPO) and palm kernel, the kernel crushers to produce crude palm kernel oil (CPKO), the refinery to produce refined palm oil (RPO) and finally the palm biodiesel plant to produce palm biodiesel. This assessment aims to investigate the life cycle assessment (LCA) of germinated oil palm seeds and the use of LCA to identify the stage/s in the production of germinated oil palm seeds that could contribute to the environmental load. The method for the life cycle impact assessment (LCIA) is modelled using SimaPro version 7, (System for Integrated environMental Assessment of PROducts), an internationally established tool used by LCA practitioners. This software contains European and US databases on a number of materials in addition to a variety of European- and US-developed impact assessment methodologies. LCA was successfully conducted for five seed production units and it was found that the environmental impact for the production of germinated oil palm was not significant. The characterised results of the LCIA for the production of 1000 germinated oil palm seeds showed that fossil fuel was the major impact category followed by respiratory inorganics and climate change.
Kraft lignin (KL) is a renewable source of many valuable intermediate biochemical products currently derived from petroleum. An excessive of lignin comes from pulping wastewater caused an adverse pollution problems hence affecting human and aquatic life. A comprehensive study pertaining to emulsion liquid membrane (ELM) extraction of lignin from pulping wastewater was presented. ELM formulation contains Aliquat 336 as carrier, kerosene as diluent, sodium bicarbonate (NaHCO3 ) as stripping agent and Span 80 as surfactant. The emulsion stability was investigated at different surfactant concentrations, homogenizer speed and emulsification time. Modifier (2-ethyl-1-hexanol) was added to avoid segregation of third phase while improving the emulsion stability. At optimum conditions, 95% and 56% of lignin were extracted and recovered, respectively at 10 min of extraction time, 0.007 M of Aliquat 336, 0.1 M of NaHCO3 and 1:5 of treat ratio. Additional of modifier was contributed to highest recovery up to 98%. The ELM process was found to be equally feasible and quite effective in the recovery of KL from real pulping wastewater. Therefore, ELM process provides a promising alternative technology to recover KL from pulping wastewater while solving the environmental problems simultaneously.
Petrol is known to be hazardous to human health and is associated with various health effects, such as haematotoxicity and oxidative stress. Although Malaysia has adopted the European fuel quality standards in recent years in order to reduce petroleum pollutants and to improve air quality, gasoline with research octane number 95 (RON95), believed to contain benzene and other toxic substances, is still widely used all over the country. This study assessed the effect of RON95 gasoline on haemtological parameters of rats after 11 weeks of exposure.
Compound-specific isotope analysis (CSIA) offers great potential as a tool to provide chemical evidence in a forensic investigation. Many attempts to trace environmental oil spills were successful where isotopic values were particularly distinct. However, difficulties arise when a large data set is analyzed and the isotopic differences between samples are subtle. In the present study, discrimination of diesel oils involved in a diesel theft case was carried out to infer the relatedness of the samples to potential source samples. This discriminatory analysis used a suite of hydrocarbon diagnostic indices, alkanes, to generate carbon and hydrogen isotopic data of the compositions of the compounds which were then processed using multivariate statistical analyses to infer the relatedness of the data set. The results from this analysis were put into context by comparing the data with the δ(13)C and δ(2)H of alkanes in commercial diesel samples obtained from various locations in the South Island of New Zealand. Based on the isotopic character of the alkanes, it is suggested that diesel fuels involved in the diesel theft case were distinguishable. This manuscript shows that CSIA when used in tandem with multivariate statistical analysis provide a defensible means to differentiate and source-apportion qualitatively similar oils at the molecular level. This approach was able to overcome confounding challenges posed by the near single-point source of origin, i.e., the very subtle differences in isotopic values between the samples.
Clausena excavata (Lour.), locally known as "Kemantu hitam," is a common plant in Malaysian folklore medicine. This study evaluated the antioxidant properties of the solvent extracts of C. excavata leaves and determined the acute toxicity of methanolic extract C. excavata (MECE) leaves in Sprague-Dawley rats. Harvested leaves were dried and subjected to solvent extraction using petroleum ether, chloroform, ethyl acetate and methanol in succession. The antioxidant activity of each extract was determined using the ferric-reducing antioxidant power (FRAP) and 2,2-diphenyl-1-picryl dihydrazyl (DPPH) radical scavenging activity. The total phenolic content (TPC) and total flavonoids content (TFC) were estimated by Folin-Ciocalteu and ethanolic aluminium chloride method, respectively. The chloroform extract was found to be highest in flavonoid content, while the methanolic extract showed the highest TPC and antioxidant activity. There was no mortality in rats treated with MECE leaves even at a high dose of 5000 mg/kg body weight. However, the MECE leaves produced mild to moderate pathological changes in the liver and kidneys, shown by mild degenerative changes and leucocyte infiltration. The extract did not affect the haematological parameters or relative weights of the liver or kidneys. Overall, the MECE leaves have potent antioxidant activity and are presumed safe to be used orally as health-promoting product at low to moderate doses.
The present study was conducted to determine the antinociceptive potential of methanol extract of Muntingia calabura L. (MEMC) and to isolate and identify the bioactive compound(s) responsible for the observed antinociceptive activity. The MEMC and its partitions (petroleum ether (PEP), ethyl acetate (EAP), and aqueous (AQP) partitions), in the dose range of 100, 500, and 1000 mg/kg, were tested using the formalin-induced nociceptive test. The PEP, which exerted the most effective activity in the respective early and late phase, was further subjected to the fractionation procedures and yielded seven fractions (labelled A to G). These fractions were tested, at the dose of 300 mg/kg, together with distilled water or 10% DMSO (negative controls); morphine and aspirin (positive controls) for potential antinociceptive activity. Of all fractions, Fraction D showed the most significant antinociceptive activity, which is considered as equieffective to morphine or aspirin in the early or late phase, respectively. Further isolation and identification processes on fraction D led to the identification of three known and one new compounds, namely, 5-hydroxy-3,7,8-trimethoxyflavone (1), 3,7-dimethoxy-5-hydroyflavone (2), 2',4'-dihydroxy-3'-methoxychalcone (3), and calaburone (4). At the dose of 50 mg/kg, compound 3 exhibited the highest percentage of antinociceptive activity in both phases of the formalin test. In conclusion, the antinociceptive activity of MEMC involved, partly, the synergistic activation of the flavonoid types of compounds.
The synthesis of fatty acid methyl ester (FAME) from the high- and low-acid-content feedstock of crude palm oil (CPO) and karanj oil (KO) was conducted over CaO-La2O3-Al2O3 mixed-oxide catalyst. Various reaction parameters were investigated using a batch reactor to identify the best reaction condition that results in the highest FAME yield for each type of oil. The transesterification of CPO resulted in a 97.81% FAME yield with the process conditions of 170°C reaction temperature, 15:1 DMC-to-CPO molar ratio, 180min reaction time, and 10wt.% catalyst loading. The transesterification of KO resulted in a 96.77% FAME yield with the conditions of 150°C reaction temperature, 9:1 DMC-to-KO molar ratio, 180min reaction time, and 5wt.% catalyst loading. The properties of both products met the ASTM D6751 and EN 14214 standard requirements. The above results showed that the CaO-La2O3-Al2O3 mixed-oxide catalyst was suitable for high- and low-acid-content vegetable oil.
Almost over ten years, environmental experts have concentrated on implementing risk-based management strategies for the remediation of sites contaminated with total petroleum hydrocarbons (TPHs), which can potentially have detrimental ecological impacts. Phytoremediation widely recognized as a green technology a plant-based and economically efficient technology, emerges as a promising method to offer an alternative to existing treatment technologies in TPH contaminated ecosystems. The utilization of Scirpus grossus, a perennial plant, has been proposed as a practical, safe, and cost-effective method for remediating soil contaminated with petroleum hydrocarbons. This study aimed to evaluate the efficacy of S. grossus in removing total petroleum hydrocarbons (TPH) in real crude-oil sludge. Employing a batch phytoremediation system with S. grossus, the experiment was conducted in crates within a greenhouse, maintaining ambient temperatures (30 °C-35 °C) for a duration of 28 days. Each crate was populated with 9-month-old plants of uniform size, initially cultivated in the greenhouse before being transplanted into crates containing 100 % crude-oil sludge with an initial TPH concentration of 37,554 mg/kg for the treatment phase. TPH removal rates were assessed after 14, 21, and 28 days of exposure, resulting in removal rates of 67 %, 74 %, and 75 %, respectively. The highest concentration of rhizobacteria recorded in both sample (with contaminants and without contaminants) were 5.56 × 104 and 5.72 × 104 CFU/mL respectively. Furthermore, TPH extraction from both stems and roots of S. grossus was analysed, revealing the highest TPH concentration of 15,319 mg/kg and about 8000 mg/kg of TPH at day 28 by roots and stem sample respectively. In conclusion, S. grossus demonstrated substantial potential in effectively mitigating the toxicity of TPH in real crude-oil sludge contamination scenarios.