Displaying publications 141 - 160 of 490 in total

Abstract:
Sort:
  1. Hazura Haroon, Siti Sarah Khalid
    MyJurnal
    This paper provides a qualitative overview of different Optical Fiber Sensors (OFS),
    which play important role in the field of sensors due to their excellent
    characteristics, spontaneous response and easy handling system. The current
    state of the art of optical fiber technology is reviewed, namely based on its main
    characteristics and sensing advantages. In addition, the working principle of OFS
    and their applications are discussed, particularly for sensor employment.
    Matched MeSH terms: Physical Phenomena
  2. He MQ, Shen JY, Petrović AP, He QL, Liu HC, Zheng Y, et al.
    Sci Rep, 2016 09 02;6:32508.
    PMID: 27587000 DOI: 10.1038/srep32508
    In the interfacial superconductor Bi2Te3/Fe1+yTe, two dimensional superconductivity occurs in direct vicinity to the surface state of a topological insulator. If this state were to become involved in superconductivity, under certain conditions a topological superconducting state could be formed, which is of high interest due to the possibility of creating Majorana fermionic states. We report directional point-contact spectroscopy data on the novel Bi2Te3/Fe1+yTe interfacial superconductor for a Bi2Te3 thickness of 9 quintuple layers, bonded by van der Waals epitaxy to a Fe1+yTe film at an atomically sharp interface. Our data show highly unconventional superconductivity, which appears as complex as in the cuprate high temperature superconductors. A very large superconducting twin-gap structure is replaced by a pseudogap above ~12 K which persists up to 40 K. While the larger gap shows unconventional order parameter symmetry and is attributed to a thin FeTe layer in proximity to the interface, the smaller gap is associated with superconductivity induced via the proximity effect in the topological insulator Bi2Te3.
    Matched MeSH terms: Physical Phenomena
  3. Ho, L.H., Zainal Abidin, N.F.S., Tan, T.C., Noroul Asyikeen, Z.
    MyJurnal
    The effect of partial substitution of pumpkin flour for rice flour on the physical properties and sensory attributes of gluten-free muffin were investigated. Pumpkin flour was used to replace 10, 15 and 20% rice flour in a control gluten-free muffin formulation (without pumpkin flour). The partial substitution of pumpkin flour for rice flour did not affect moisture content of gluten-free muffins. However, the pumpkin flour substitution caused significant reduction in water activity of gluten-free muffins. Results on the volume, specific volume and height of all gluten-free muffins showed no significant effect with the increasing percentage of pumpkin flour substitution. However, pumpkin flour substitution significantly reduced the firmness of composite muffins, and improved its springiness. The colour of crumb progressively became darker as the level of pumpkin flour substitution increased. Moreover, the results also showed that the substitution of pumpkin flour caused an increase in yellowness (b*) value of crust and crumb of gluten-free muffin. Sensory evaluation indicated that all gluten-free muffins incorporated with pumpkin flour received similar score when compared to that of control.
    Matched MeSH terms: Physical Phenomena
  4. Hooi, M.H., Tiong, W. K., Tay, K. G., Chiew,K. L., Sze, S. N.
    MATEMATIKA, 2018;34(2):333-350.
    MyJurnal
    In this paper, we look at the propagation of internal solitary waves over three
    different types of slowly varying region, i.e. a slowly increasing slope, a smooth bump and
    a parabolic mound in a two-layer fluid flow. The appropriate mathematical model for this
    problem is the variable-coefficient extended Korteweg-de Vries equation. The governing
    equation is then solved numerically using the method of lines. Our numerical simulations
    show that the internal solitary waves deforms adiabatically on the slowly increasing slope.
    At the same time, a trailing shelf is generated as the internal solitary wave propagates
    over the slope, which would then decompose into secondary solitary waves or a wavetrain.
    On the other hand, when internal solitary waves propagate over a smooth bump or a
    parabolic mound, a trailing shelf of negative polarity would be generated as the results of
    the interaction of the internal solitary wave with the decreasing slope of the bump or the
    parabolic mound. The secondary solitary waves is observed to be climbing the negative
    trailing shelf.
    Matched MeSH terms: Physical Phenomena
  5. Hoque A, Tariqul Islam M, Almutairi AF, Alam T, Jit Singh M, Amin N
    Sensors (Basel), 2018 Nov 30;18(12).
    PMID: 30513675 DOI: 10.3390/s18124209
    In this paper, a dual-band metamaterial absorber (MMA) ring with a mirror reflexed C-shape is introduced for X and Ku band sensing applications. The proposed metamaterial consists of two square ring resonators and a mirror reflexed C-shape, which reveals two distinctive absorption bands in the electromagnetic wave spectrum. The mechanism of the two-band absorber particularly demonstrates two resonance frequencies and absorption was analyzed using a quasi-TEM field distribution. The absorption can be tunable by changing the size of the metallic ring in the frequency spectrum. Design and analysis of the proposed meta-absorber was performed using the finite-integration technique (FIT)-based CST microwave studio simulation software. Two specific absorption peaks value of 99.6% and 99.14% are achieved at 13.78 GHz and 15.3 GHz, respectively. The absorption results have been measured and compared with computational results. The proposed dual-band absorber has potential applications in sensing techniques for satellite communication and radar systems.
    Matched MeSH terms: Physical Phenomena
  6. Horiguchi T, Masui Y, Zan MSD
    Sensors (Basel), 2019 Mar 27;19(7).
    PMID: 30934806 DOI: 10.3390/s19071497
    Distributed strain and temperature can be measured by using local Brillouin backscatter in optical fibers based on the strain and temperature dependence of the Brillouin frequency shift. The technique of analyzing the local Brillion backscatter in the time domain is called Brillouin optical time domain reflectometry (BOTDR). Although the best spatial resolution of classic BOTDR remains at around 1 m, some recent BOTDR techniques have attained as high as cm-scale spatial resolution. Our laboratory has proposed and demonstrated a high-spatial-resolution BOTDR called phase-shift pulse BOTDR (PSP-BOTDR), using a pair of probe pulses modulated with binary phase-shift keying. PSP-BOTDR is based on the cross-correlation of Brillouin backscatter and on the subtraction of cross-correlations obtained from the Brillouin scatterings evoked by each phase-modulated probe pulse. Although PSP-BOTDR has attained 20-cm spatial resolution, the spectral analysis method of PSP-BOTDR has not been discussed in detail. This article gives in-depth analysis of the Brillouin backscatter and the correlations of the backscatters of the PSP-BOTDR. Based on the analysis, we propose new spectral analysis methods for PSP-BOTDR. The analysis and experiments show that the proposed methods give better frequency resolution than before.
    Matched MeSH terms: Physical Phenomena
  7. Hosen MA, Alengaram UJ, Jumaat MZ, Sulong NHR, Darain KMU
    Polymers (Basel), 2017 May 19;9(5).
    PMID: 30970858 DOI: 10.3390/polym9050180
    Reinforced concrete (RC) structures require strengthening for numerous factors, such as increased load, modification of the structural systems, structural upgrade or errors in the design and construction stages. The side near-surface mounted (SNSM) strengthening technique with glass fiber-reinforced polymer (GFRP) bars is a relatively new emerging technique for enhancing the flexural capacities of existing RC elements. Nine RC rectangular beams were flexurally strengthened with this technique and tested under four-point bending loads until failure. The main goal of this study is to optimize the structural capacity of the RC beams by varying the amount of strengthening reinforcement and bond length. The experimental test results showed that strengthening with SNSM GFRP bars significantly enhanced the flexural responses of the specimens compared with the control specimen. The first cracking and ultimate loads, energy absorption capacities, ductility and stiffness were remarkably enhanced by the SNSM technique. It was also confirmed that the bond length of the strengthened reinforcement greatly influences the energy absorption capacities, ductility and stiffness. The effect of the bond length on these properties is more significant compared to the amount of strengthening reinforcement.
    Matched MeSH terms: Physical Phenomena
  8. Hosen MA, Jumaat MZ, Alengaram UJ, Islam ABMS, Bin Hashim H
    Polymers (Basel), 2016 Mar 03;8(3).
    PMID: 30979167 DOI: 10.3390/polym8030067
    Existing structural components require strengthening after a certain period of time due to increases in service loads, errors in design, mechanical damage, and the need to extend the service period. Externally-bonded reinforcement (EBR) and near-surface mounted (NSM) reinforcement are two preferred strengthening approach. This paper presents a NSM technique incorporating NSM composites, namely steel and carbon fiber-reinforced polymer (CFRP) bars, as reinforcement. Experimental and analytical studies carried out to explore the performance of reinforced concrete (RC) members strengthened with the NSM composites. Analytical models were developed in predicting the maximum crack spacing and width, concrete cover separation failure loads, and deflection. A four-point bending test was applied on beams strengthened with different types and ratios of NSM reinforcement. The failure characteristics, yield, and ultimate capacities, deflection, strain, and cracking behavior of the beams were evaluated based on the experimental output. The test results indicate an increase in the cracking load of 69% and an increase in the ultimate load of 92% compared with the control beam. The predicted result from the analytical model shows good agreement with the experimental result, which ensures the competent implementation of the present NSM-steel and CFRP technique.
    Matched MeSH terms: Physical Phenomena
  9. Hossain MZ, Selvaraj JA, Rahim NA
    PLoS One, 2018;13(11):e0206691.
    PMID: 30500857 DOI: 10.1371/journal.pone.0206691
    Over the past few years, high step-up dc-dc converters have been drawn substantial attention because of their wide-ranging application not only in the renewable energy sector but also in many other applications. To acquire a high voltage gain in photovoltaic (PV) and other renewable energy applications, a high step-up dc-dc converter is proposed in this paper. The proposed converter structure consists of a full-bridge (FB) module along with an input boost inductor and a voltage multiplier based on the Cockcroft-Walton (CW) principle with a parallel inductor. The key features of the proposed converter are: 1) high voltage gain with lower voltage stress on the switches, diodes and other passive elements without affecting the number of cascaded stages, 2) a minimum size of boost inductance and cascaded stage capacitance that ensures its compactness and low cost, and 3) a minimal number of major components. Circuit operation, steady-state analysis and various design parameters of the proposed converter are explained in details. In order to prove the performance of the theoretical analysis, a laboratory prototype is also implemented. The peak voltage gain and the maximum efficiency obtained are 11.9 and 94.6% respectively with very low input current ripple and output voltage ripple generated.
    Matched MeSH terms: Physical Phenomena
  10. Humada AM, Hojabri M, Sulaiman MH, Hamada HM, Ahmed MN
    PLoS One, 2016;11(4):e0152766.
    PMID: 27035575 DOI: 10.1371/journal.pone.0152766
    A grid-connected photovoltaic (PV) system operates under fluctuated weather condition has been modeled and characterized based on specific test bed. A mathematical model of a small-scale PV system has been developed mainly for residential usage, and the potential results have been simulated. The proposed PV model based on three PV parameters, which are the photocurrent, IL, the reverse diode saturation current, Io, the ideality factor of diode, n. Accuracy of the proposed model and its parameters evaluated based on different benchmarks. The results showed that the proposed model fitting the experimental results with high accuracy compare to the other models, as well as the I-V characteristic curve. The results of this study can be considered valuable in terms of the installation of a grid-connected PV system in fluctuated climatic conditions.
    Matched MeSH terms: Physical Phenomena
  11. Hussain M
    Curr Drug Deliv, 2019;16(7):618-627.
    PMID: 30868954 DOI: 10.2174/1567201816666190313155117
    BACKGROUND: Glycyrrhizic acid (GA) is a glycoside that has shown considerable promise as a penetration enhancer and drug carrier to improve the absorption of poorly water-soluble drugs. The aggregation behavior of GA and its ability to form large micelles at higher solution concentrations are thought to contribute to these bioavailability enhancing properties. The oral absorption of Paclitaxel (PTX) for example, an anti-cancer agent which exhibits poor oral bioavailability, has been found to significantly increase in the presence of GA.

    METHODS: In an attempt to visualize the aggregation behavior of GA and its subsequent association with PTX, 100 ns molecular dynamics simulation of a 5 mM aqueous solution of GA with 10 molecules of PTX was conducted using GROMACS and an all-atom forcefield.

    RESULTS: Aggregation of GA molecules was found to occur quickly at this level of saturation leading to two stable aggregates of 13 and 17 GA molecules with an effective radius of 10.17 nm to 10.92 nm. These aggregates form not in isolation, but together with PTX molecule embedded within the structures, which reduces the number of interactions and hydrogen-bonding with water.

    CONCLUSION: GA aggregation occurs around PTX molecules in solution, forming co-joined GA-PTX cluster units at a ratio of 3:1. These clusters remain stable for the remainder of the 100ns simulation and serve to isolate and protect PTX from the aqueous environment.

    Matched MeSH terms: Physical Phenomena
  12. Ibrahim IR, Matori KA, Ismail I, Awang Z, Rusly SNA, Nazlan R, et al.
    Sci Rep, 2020 Feb 21;10(1):3135.
    PMID: 32081972 DOI: 10.1038/s41598-020-60107-1
    Microwave absorption properties were systematically studied for double-layer carbon black/epoxy resin (CB) and Ni0.6Zn0.4Fe2O4/epoxy resin (F) nanocomposites in the frequency range of 8 to 18 GHz. The Ni0.6Zn0.4Fe2O4 nanoparticles were synthesized via high energy ball milling with subsequent sintering while carbon black was commercially purchased. The materials were later incorporated into epoxy resin to fabricate double-layer composite structures with total thicknesses of 2 and 3 mm. The CB1/F1, in which carbon black as matching and ferrite as absorbing layer with each thickness of 1 mm, showed the highest microwave absorption of more than 99.9%, with minimum reflection loss of -33.8 dB but with an absorption bandwidth of only 2.7 GHz. Double layer absorbers with F1/CB1(ferrite as matching and carbon black as absorbing layer with each thickness of 1 mm) structure showed the best microwave absorption performance in which more than 99% microwave energy were absorbed, with promising minimum reflection loss of -24.0 dB, along with a wider bandwidth of 4.8 GHz and yet with a reduced thickness of only 2 mm.
    Matched MeSH terms: Physical Phenomena
  13. Ibrahim KA, Naz MY, Shukrullah S, Sulaiman SA, Ghaffar A, AbdEl-Salam NM
    Sci Rep, 2020 Apr 03;10(1):5927.
    PMID: 32246028 DOI: 10.1038/s41598-020-62793-3
    The world does not have too much time to ensure that the fast-growing population has enough land, food, water and energy. The rising food demand has brought a positive surge in fertilizers' demand and agriculture-based economy. The world is using 170 million tons of fertilizer every year for food, fuel, fiber, and feed. The nitrogenous fertilizers are being used to meet 48% of the total food demand of the world. High fertilizer inputs augment the reactive nitrogen levels in soil, air, and water. The unassimilated reactive nitrogen changes into a pollutant and harms the natural resources. The use of controlled-release fertilizers for slowing down the nutrients' leaching has recently been practiced by farmers. However, to date, monitoring of the complete discharge time and discharge rate of controlled released fertilizers is not completely understood by the researchers. In this work, corn starch was thermally processed into a week gel-like coating material by reacting with urea and borate. The granular urea was coated with native and processed starch in a fluidized bed reactor having bottom-up fluid delivery system. The processed starch exhibited better thermal and mechanical stability as compared to the native starch. Unlike the pure starch, the storage modulus of the processed starch dominated the loss modulus. The release time of urea, coated with processed starch, remained remarkably larger than the uncoated urea.
    Matched MeSH terms: Physical Phenomena
  14. Ibrahim Lakin I, Abbas Z, Azis RS, Abubakar Alhaji I
    Materials (Basel), 2020 Oct 16;13(20).
    PMID: 33081082 DOI: 10.3390/ma13204602
    This study was aimed at fabricating composites of polylactic acid (PLA) matrix-reinforced oil palm empty fruit bunch (OPEFB) fiber filled with chemically reduced graphene oxide (rGO). A total of 2-8 wt.% rGO/OPEFB/PLA composites were characterized for their complex permittivity using an open-ended coaxial probe (OEC) technique. The shielding efficiency properties were calculated using the measured transmission (S21) and the reflection (S11) coefficient results. All the measurements and calculations were performed in the 8-12 GHz frequency range. The morphological and microstructural study included X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and Fourier transform infrared spectroscopy (FTIR). The results indicated that the incorporation of rGO as filler into the composites enhanced their complex permittivity properties. The composites showed a total shielding efficiency (SET) of about 31.2 dB at a frequency range of 8-12 GHz, which suggests their usefulness for microwave absorption.
    Matched MeSH terms: Physical Phenomena
  15. Ibrahim MD, Amran SNA, Yunos YS, Rahman MRA, Mohtar MZ, Wong LK, et al.
    Appl Bionics Biomech, 2018;2018:7854321.
    PMID: 29853998 DOI: 10.1155/2018/7854321
    The skin of a fast swimming shark reveals riblet structures that help reduce the shark's skin friction drag, enhancing its efficiency and speed while moving in the water. Inspired by the structure of the shark skin denticles, our team has carried out a study as an effort in improving the hydrodynamic design of marine vessels through hull design modification which was inspired by this riblet structure of shark skin denticle. Our study covers on macroscaled design modification. This is an attempt to propose an alternative for a better economical and practical modification to obtain a more optimum cruising characteristics for marine vessels. The models used for this study are constructed using computer-aided design (CAD) software, and computational fluid dynamic (CFD) simulations are then carried out to predict the effectiveness of the hydrodynamic effects of the biomimetic shark skins on those models. Interestingly, the numerical calculated results obtained show that the presence of biomimetic shark skin implemented on the vessels give about 3.75% reduction of drag coefficient as well as reducing up to 3.89% in drag force experienced by the vessels. Theoretically, as force drag can be reduced, it can lead to a more efficient vessel with a better cruising speed. This will give better impact to shipping or marine industries around the world. However, it can be suggested that an experimental procedure is best to be conducted to verify the numerical result that has been obtained for further improvement on this research.
    Matched MeSH terms: Physical Phenomena
  16. Idris AC, Saad MR, Zare-Behtash H, Kontis K
    Sensors (Basel), 2014;14(4):6606-32.
    PMID: 24721773 DOI: 10.3390/s140406606
    Scramjets have become a main focus of study for many researchers, due to their application as propulsive devices in hypersonic flight. This entails a detailed understanding of the fluid mechanics involved to be able to design and operate these engines with maximum efficiency even at their off-design conditions. It is the objective of the present cold-flow investigation to study and analyse experimentally the mechanics of the fluid structures encountered within a generic scramjet inlet at M = 5. Traditionally, researchers have to rely on stream-thrust analysis, which requires the complex setup of a mass flow meter, a force balance and a heat transducer in order to measure inlet-isolator performance. Alternatively, the pitot rake could be positioned at inlet-isolator exit plane, but this method is intrusive to the flow, and the number of pitot tubes is limited by the model size constraint. Thus, this urgent need for a better flow diagnostics method is addressed in this paper. Pressure-sensitive paint (PSP) has been applied to investigate the flow characteristics on the compression ramp, isolator surface and isolator sidewall. Numerous shock-shock interactions, corner and shoulder separation regions, as well as shock trains were captured by the luminescent system. The performance of the scramjet inlet-isolator has been shown to improve when operated in a modest angle of attack.
    Matched MeSH terms: Physical Phenomena
  17. Iffa ED, Aziz AR, Malik AS
    Appl Opt, 2011 Feb 10;50(5):618-25.
    PMID: 21343981 DOI: 10.1364/AO.50.000618
    This paper utilizes the background oriented schlieren (BOS) technique to measure the velocity field of a variable density round jet. The density field of the jet is computed based on the light deflection created during the passage of light through the understudy jet. The deflection vector estimation was carried out using phase-based optical flow algorithms. The density field is further exploited to extract the axial and radial velocity vectors with the aid of continuity and energy equations. The experiment is conducted at six different jet-exit temperature values. Additional turbulence parameters, such as velocity variance and power spectral density of the vector field, are also computed. Finally, the measured velocity parameters are compared with the hot wire anemometer measurements and their correlation is displayed.
    Matched MeSH terms: Physical Phenomena
  18. Ishak MI, Dobryden I, Martin Claesson P, Briscoe WH, Su B
    J Colloid Interface Sci, 2021 Feb 01;583:414-424.
    PMID: 33011410 DOI: 10.1016/j.jcis.2020.09.038
    Frictional and nanomechanical properties of nanostructured polymer surfaces are important to their technological and biomedical applications. In this work, poly(ethylene terephthalate) (PET) surfaces with a periodic distribution of well-defined nanopillars were fabricated through an anodization/embossing process. The apparent surface energy of the nanopillared surfaces was evaluated using the Fowkes acid-base approach, and the surface morphology was characterized using scanning electron microscope (SEM) and atomic force microscope (AFM). The normal and lateral forces between a silica microparticle and these surfaces were quantified using colloidal probe atomic force microscopy (CP-AFM). The friction-load relationship followed Amonton's first law, and the friction coefficient appeared to scale linearly with the nanopillar height. Furthermore, all the nanopillared surfaces showed pronounced frictional instabilities compared to the smooth sliding friction loop on the flat control. Performing the stick-slip amplitude coefficient (SSAC) analysis, we found a correlation between the frictional instabilities and the nanopillars density, pull-off force and work of adhesion. We have summarised the dependence of the nanotribological properties on such nanopillared surfaces on five relevant parameters, i.e. pull-off force fp, Amontons' friction coefficient μ, RMS roughness Rq, stick-slip amplitude friction coefficient SSAC, and work of adhesion between the substrate and water Wadh in a radar chart. Whilst demonstrating the complexity of the frictional behaviour of nanopillared polymer surfaces, our results show that analyses of multiparametric nanotribological properties of nanostructured surfaces should go beyond classic Amontons' laws, with the SSAC more representative of the frictional properties compared to the friction coefficient.
    Matched MeSH terms: Physical Phenomena
  19. Islam MA, Auta M, Kabir G, Hameed BH
    Bioresour Technol, 2016 Jan;200:335-41.
    PMID: 26512856 DOI: 10.1016/j.biortech.2015.09.057
    The combustion characteristics of Karanj fruit hulls char (KFH-char) was investigated with thermogravimetry analysis (TGA). The TGA outlined the char combustion thermographs at a different heating rate and isoconversional methods expressed the combustion kinetics. The Kissinger-Akahira-Sunose (KAS) and Flynn-Wall-Ozawa (FWO) methods authenticated the char average activation energy at 62.13 and 68.53kJ/mol respectively, enough to derive the char to burnout. However, the Coats-Redfern method verified the char combustion via complex multi-step mechanism; the second stage mechanism has 135kJ/mol average activation energy. The TGA thermographs and kinetic parameters revealed the adequacy of the KFH-char as fuel substrate than its precursor, Karanj fruit hulls (KFH).
    Matched MeSH terms: Physical Phenomena
  20. Ismail Lias, Muhammad Hussain Ismail, Iskandar Dzulkernain Md Raffee, Mohd Aman Ihsan Mamat
    MyJurnal
    Aluminium foam tube is a metal that consists of porous medium with special characteristics such as good energy absorption, good heat transfer and high thermal conductivity. These make it suitable to be used in a wide range of applications such as in heat exchangers. The aim of this project is to identify and analyse mechanical behaviour and microstructure aluminium foam tube produced and fabricated with infiltration method with vacuum-gas. The density of aluminium foam tube was also determined and an average aluminium foam tube with porosity 50% - 80% with the average NaCl particle size 2mm, 3mm and 4mm was produced. Foams with porosity 60%-75% NaCl has higher energy absorption. These was based on foam structure, density and maximum compressive load test result.
    Matched MeSH terms: Physical Phenomena
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links