Water treatment plants generate vast amounts of sludge and its disposal is one of the most expensive and environmentally problematic challenges worldwide. As sludge from water treatment plants contains a considerable amount of titanium, both can create serious environmental concerns. In this study, the potential to recover titanium from drinking water treatment residue was explored through acid leaching technique. Statistical design for the optimization of titanium recovery was proposed using response surface methodology (RSM) based on a five-level central composite design (CCD). Three independent variables were investigated, namely the acid concentration (3 M-7 M), temperature (40 °C - 80 °C) and solid/liquid ratio (0.005-0.02 g/mL). According to the analysis of variance (ANOVA), the p-value (<0.0001) indicated the designed model was highly significant. Optimization using RSM gave the best fit between validated and predicted data as elucidated by the coefficient of determination with R2 values of 0.9965. However, acid concentration and solid/liquid ratio showed an initial increase in titanium recovery followed by recovery reduction with increasing concentration and ratio. Quadratic RSM predicted the maximum recovery of titanium to be 67.73% at optimal conditions of 5.5 M acid concentration, at a temperature of 62 °C with a solid/liquid ratio of 0.01 g/mL. The verification experiments gave an average of 66.23% recovery of titanium, thus indicating that the successfully developed model to predict the response. This process development has significant importance to reduce the cost of waste disposal, environmental protection, and recovery of economically valuable products.
In China, waste sorting practice is not strictly followed, plastics, especially food packaging, are commonly mixed in food waste. Supercritical water gasification (SCWG) of unsorted food waste was conducted in this study, using model unsorted food waste by mixture of pure food waste and plastic. Different operating parameters including reaction temperature, residence time, and feedstock concentration were investigated. Moreover, the effect of three representative food additives namely NaCl, NaHCO3 and Na2CO3 were tested in this work. Finally, comparative analysis about SCWG of unsorted food waste, pure food waste, and plastic was studied. It was found that higher reaction temperature, longer residence time and lower feedstock concentration were advantageous for SCWG of unsorted food waste. Within the range of operating parameters in this study, when the feedstock concentration was 5 wt%, the highest H2 yield (7.69 mol/kg), H2 selectivity (82.11%), total gas yield (17.05 mol/kg), and efficiencies of SCWG (cold gas efficiency, gasification efficiency, carbon gasification efficiency, and hydrogen gasification efficiency) were obtained at 480 °C for 75 min. Also, the addition of food additives with Na+ promoted the SCWG of unsorted food waste. The Na2CO3 showed the best catalytic performance on enhancement of H2 and syngas production. This research demonstrated the positive effect of waste sorting on the SCWG of food waste, and provided novel results and information that help to overcome the problems in the process of food waste treatment and accelerate the industrial application of SCWG technology in the future.
This study investigates the published literature and incorporates our field data from 1997 to September 2018 to generate an inventory report of primary freshwater fishes for Perak State in Malaysia. We critically examined and enumerated 186 species from 2 classes, 16 orders, 43 families and 114 genera in 57 localities. A total of 173 fish species (91.4%) are native to Perak and 17 species (8.6%) are non-native. The provisional checklist presented herein is conservative and excludes doubtful inventory records that lack synthesis and traceability. We encountered seven taxonomic discrepancies and we also could not confidently identify eight species. These are explicitly discussed to inform future workers.
Treated palm oil mill effluents (POME) is of great concern as it still has colour from its dissolved organics which may pollute receiving water bodies. In this study, the removal of colour from treated palm oil mill effluent were investigated through adsorption studies using carbon derived from wastewater sludge (WSC). Sludge from activated sludge plants were dried and processed to produce WSC. In this study, three different bed depths of WSC were used: 5 cm, 10 cm, and 15 cm. For each bed depth, the flowrate was varied at three different values: 100 mL/hr, 50 mL/hr and 25 mL/hr. It was found that at bed depth of 5 cm, the breakthrough curves were occurred at 360 min, 150 min and 15 min for flowrates of 25, 50 and 100 mL/hr respectively. It was observed that at a particular depth the exhaustion time for column reduced as flow rate increases. Kinetic models, Adams-Bohart and Yoon-Nelson were used to analyze the performance of the adsorption. It was found that rate constant for Adams Bohart model decreased with the increase in bed depth. Adsorption capacity obtained from Adams-Bohart model ranged from 2676.19 mg/L up to 8938.78 mg/L. The maximum adsorption capacity increases with smaller bed depth. For Yoon-Nelson model, the rate constant decreases with increase in bed depth. The required time for 50% breakthrough obtained from the models ranged from 17.01 to 104.17 minutes for all three bed depths. The reduction of colour was found to be effective at all bed depths. The experimental data was best described by both models as with higher values of correlation coefficient (R2).
Matched MeSH terms: Water Purification; Waste Water
Classified as a small island, Kapas Island experiences major problems especially in supplying freshwater where groundwater abstraction is the only way to meet the demand of drinking water and domestic use. Groundwater samples were collected from seven constructed boreholes to examine the hydrochemistry properties of major ions and in-situ parameters as these could provide a basis for future reference. The chemical composition showed strong and significant correlation for each studied parameter; an indication of the effect of environmental variables to the groundwater composition. The composition changed from Ca-rich to Na-rich are explained mostly by mixing and cation exchange processes. This study provided an input for water management at Kapas Island where groundwater is a crucial resource to maintain the hydrogeological balance of the island.
A study of spatial and temporal variations on water quality and trophic status was conducted twice a month from December
2012 to January 2014 in four sampling stations at Bukit Merah Reservoir (BMR). The concentration of dissolved oxygen
(DO), water temperature, conductivity, total dissolved solids (TDS), total phosphorous (TP), PO4
-
, NO2
-
, NO3
-
, NH4
+ and
net primary productivity had significant differences temporally (p<0.05) except for pH, total suspended solids (TSS)
and chlorophyll-a. Based on correlation analysis, the amount of rainfall and rain days has negatively correlated with
secchi depth and chlorophyll-a (p<0.01). The water level has significantly decreased the value of the temperature, pH,
conductivity, TP and NO2
-
but it has positive correlation with NO3
-
and NH4
+. Discharged from Sungai Kurau increased
the value of conductivity, TSS, TP and NO2
-
as a result from runoff and erosion, thus decreasing the secchi depth values,
NO3
-
and NH4
+. The water quality of BMR is classified in Class II and TSI indicates that the BMR has an intermediate level
of productivity (mesotrophic) and meets the objective of this reservoir which was to provide water for paddy irrigation.
This study was conducted to examine the production of bioflocculants using agricultural wastewater as a fermentation feedstock under different temperatures and incubation times. The mechanism of flocculation was studied to gain a detailed understanding of the flocculation activity. The highest bioflocculant yield (2.03 g/L) at a temperature of 40 °C was produced in a palm oil mill effluent medium (BioF-POME). Bioflocculant produced from a fermented SME medium (BioF-SME) showed the highest activity. The flocculation tests for colour and turbidity removal from lake water indicated that BioF-SME and BioF-POME performed comparably to commercial alum. Analyses of the bioflocculants using liquid chromatography-mass spectrometry (LC-MS) found that the bioflocculants contained xylose and glucose. The mechanism study showed that flocculation occurred through charge neutralization and interparticle bridging between the bioflocculant polymer and the particles in the lake water. Thus, agricultural wastewater can be used as a fermentation feedstock for high-quality bioflocculants.
The biodegradability and safety of the bioflocculants make them a potential alternative to non-biodegradable chemical flocculants for wastewater treatment. However, low yield and production cost has been reported to be the limiting factor for large scale bioflocculant production. Although the utilization of cheap nutrient sources is generally appealing for large scale bioproduct production, exploration to meet the demand for them is still low. Although much progress has been achieved at laboratory scale, Industrial production and application of bioflocculant is yet to be viable due to cost of the production medium and low yield. Thus, the prospects of bioflocculant application as an alternative to chemical flocculants is linked to evaluation and utilization of cheap alternative and renewable nutrient sources. This review evaluates the latest literature on the utilization of waste/wastewater as an alternative substitute for conventional expensive nutrient sources. It focuses on the mechanisms and metabolic pathways involved in microbial flocculant synthesis, culture conditions and nutrient requirements for bioflocculant production, pre-treatment, and also optimization of waste substrate for bioflocculant synthesis and bioflocculant production from waste and their efficiencies. Utilization of wastes as a microbial nutrient source drastically reduces the cost of bioflocculant production and increases the appeal of bioflocculant as a cost-effective alternative to chemical flocculants.
This review is aimed to present an in-depth review of several methodologies on magnetic
water treatment (MWT) that are employed as scale treatment in water pipeline and to
critically discuss each method in order to determine the best outcome of MWT. The
magnetically assisted water in pipeline in various applications are presented, argued and
best variables are listed according to the performance of each MWT. The advantages and
limitations of MWT are discussed and the main outcome from the review summarize the
best method in MWT, especially in effectiveness of treating scale in terms of sustained
environment benefits. Magnetic field application in water treatment has the potential to
improve the water pipeline performance and lifetime. The application is also significant in
controlling the growth of scale in upcoming system. Both of these benefits lead to healthier
water treatment, increasing and maintaining the lifetime and performance of water system.
The water sources contaminated by toxic dyes would pose a serious problem for public health. In view of this, the development of a simple yet effective method for removing dyes from industrial effluent has attracted interest from researchers. In the present work, flat sheet mixed matrix membranes (MMMs) with different physiochemical properties were fabricated by blending P84 polyimide with different concentrations of cadmium-based metal organic frameworks (MOF-2(Cd)). The resultant membranes were then used for simultaneous removal of eosin y (EY), sunset yellow (SY) and methylene blue (MB) under various process conditions. The findings indicated that the membranes could achieve high water permeability (117.8-171.4 L/m2.h.bar) and promising rejection for simultaneous dyes removal, recording value of 99.9%, 81.2% and 68.4% for MB, EY and SY, respectively. When 0.2 wt% MOF-2(Cd) was incorporated into the membrane matrix, the membrane separation efficiency was improved by 110.2% and 213.3% for EY and SY removal, respectively when compared with the pristine membrane. In addition, the optimization and modeling of membrane permeate flux and dye rejection was explored using response surface methodology. The actual and model results are in good agreement with R2 of at least 0.9983 for dye rejection and permeate flux. The high flux of the developed MMMs coupled with effective separation of dyes suggests a promising prospect of using P84 polyimide MMMs incorporated with MOF-2(Cd) for water purification.
Sustainable wastewater treatment necessitates the application of natural and green material in the approach. Thus, selecting a natural coagulant in leachate treatment is a crucial step in landfill operation to prevent secondary environmental pollution due to residual inorganic coagulant in treated effluent. Current study investigated the application of guar gum in landfill leachate treatment. Central composite design in response surface methodology was used to optimize the performance of Chemical Oxygen Demand (COD) removal. Quadratic model developed indicated the optimum COD removal 22.57% at guar gum dosage of 44.39 mg/L, pH 8.56 (natural pH of leachate) and mixing speed 79.27 rpm. Scanning electron microscopy showed that floc was compact and energy-dispersive-x-ray analysis showed that guar gum was capable to adsorb multiple ions from the leachate. Structural characterization using Fourier Transform Infrared analysis demonstrated that hydrogen bonding between guar and pollutant particles was involved in coagulation and flocculation process. Therefore, guar gum coagulant present potential to be an alternative in leachate treatment where pH requirement is not required during treatment. Simultaneously, adsorption by guar gum offers added pollutant removal advantage.
Photocatalytic conversion of carbon dioxide (CO2) into gaseous hydrocarbon fuels is an auspicious way to produce renewable fuels in addition to greenhouse gas emission mitigation. In this work, non-metals (B, O, P, and S) doped graphitic carbon nitride (g-C3N4) was prepared via solid-state polycondensation of urea for photocatalytic CO2 reduction into highly needed methane (CH4) with water under UV light irradiation. The various physicochemical characterization results reveal the successful incorporation of B, O, P, and S elements in the g-C3N4 matrix. The maximum CH4 yield of 55.10 nmol/(mLH2O.gcat) over S-doped g-C3N4 has been obtained for CO2 reduction after 7 h of irradiation. This amount of CH4 production was 1.9, 1.4, 1.7, and 2.4-folds higher than B, O, P and bare g-C3N4 samples. The doping of S did not enlarge the surface area and photon absorption ability of the g-C3N4 sample, but this significant improvement was evidently due to effective charge separation and migration. The observed results imply that the doping of non-metal elements provides improved charge separation and is an effective way to boost photocatalyst performance. This work offers an auspicious approach to design non-metal doped g-C3N4 photocatalysts for renewable fuel production and would be promising for other energy application.
Each year, nearly 30 million tons of pineapple fruit are harvested for food and drinking industries, along with the release of a huge amount of pineapple wastes. Without the proper treatment, pineapple wastes can cause adverse impacts on the environment, calling for new technologies to convert them into valuable products. Here, we review the production and application of adsorbents derived from pineapple wastes. The thermal processing or chemical modification improved the surface chemistry and porosity of these adsorbents. The specific surface areas of the pineapple wastes-based adsorbents were in range from 4.2 to at 522.9 m2·g-1. Almost adsorption systems followed the pseudo second order kinetic model, and Langmuir isotherm model. The adsorption mechanism was found with the major role of electrostatic attraction, complexation, chelation, and ion exchange. The pineapple wastes based adsorbents could be easily regenerated. We suggest the potential of the pineapple wastes towards circular economy.
Antibiotic sulfamethoxazole (SMX) has been commonly found in various water matrices, therefore effective decontamination method is urgently needed. Metal-free pristine coconut-shell-derived biochar (CSBC), synthesized by thermochemical conversion at 700 °C, was used for activating peroxymonosulfate (PMS), an oxidant, to degrade SMX, a sulfonamide antibiotic, in water. SMX degradation, maximized at 0.05 mM concentration, was 85% in 30 min at pH 5.0 in the presence of 150 mg L-1 of CSBC. Remarkably, SMX removal reached 99% in a chloride-rich CSBC/PMS system. SMX degradation was mainly attributed to the role of CSBC in enhancing PMS activation to produce combined radical (SO4•-/HO•) and nonradical (1O2) reaction pathways. The most abundant genus in the CSBC/PMS system was Methylotenera, which belonged to the Proteobacteria phylum. Thus, from a perspective of biowaste-to-resource recycling and circular bioeconomy view point, CSBC is a potential catalytic activator of PMS for the removal of sulfonamide antibiotics from aqueous environments.
Currently, research trends on aerobic granular sludge (AGS) have integrated the operating conditions of extracellular polymeric substances (EPS) towards the stability of AGS systems in various types of wastewater with different physical and biochemical characteristics. More attention is given to the stability of the AGS system for real site applications. Although recent studies have reported comprehensively the mechanism of AGS formation and stability in relation to other intermolecular interactions such as microbial distribution, shock loading and toxicity, standard operating condition control strategies for different types of wastewater have not yet been discussed. Thus, the dimensional multi-layer structural model of AGS is discussed comprehensively in the first part of this review paper, focusing on diameter size, thickness variability of each layer and diffusion factor. This can assist in facilitating the interrelation between disposition and stability of AGS structure to correspond to the changes in wastewater types, which is the main objective and novelty of this review.
High internal phase emulsions (HIPEs) show promising application in food and cosmetic industries. In this work, diacylglycerol (DAG) was applied to fabricate water-in-oil (W/O) HIPEs. DAG-based emulsion can hold 60% water and the emulsion rigidity increased with water content, indicating the water droplets acted as "active fillers". Stable HIPE with 80% water fraction was formed through the combination of 6 wt% DAG with 1 wt% polyglycerol polyricinoleate (PGPR). The addition of 1 w% kappa (κ)-carrageenan and 0.5 M NaCl greatly reduced the droplet size and enhanced emulsion rigidity, and the interfacial tension of the internal phase was reduced. Benefiting from the Pickering crystals-stabilized interface by DAG as revealed by the microscopy and enhanced elastic modulus of emulsions with the gelation agents, the HIPEs demonstrated good retaining ability for anthocyanin and β-carotene. This study provides insights for the development of W/O HIPEs to fabricate low-calories margarines, spread or cosmetic creams.
The growing prevalence of new toxins in the environment continues to cause widespread concerns. Pharmaceuticals, organic pollutants, heavy metal ions, endocrine-disrupting substances, microorganisms, and others are examples of persistent organic chemicals whose effects are unknown because they have recently entered the environment and are displaying up in wastewater treatment facilities. Pharmaceutical pollutants in discharged wastewater have become a danger to animals, marine species, humans, and the environment. Although their presence in drinking water has generated significant concerns, little is known about their destiny and environmental effects. As a result, there is a rising need for selective, sensitive, quick, easy-to-handle, and low-cost early monitoring detection systems. This study aims to deliver an overview of a low-cost carbon-based composite to detect and remove pharmaceutical components from wastewater using the literature reviews and bibliometric analysis technique from 1970 to 2021 based on the web of science (WoS) database. Various pollutants in water and soil were reviewed, and different methods were introduced to detect pharmaceutical pollutants. The advantages and drawbacks of varying carbon-based materials for sensing and removing pharmaceutical wastes were also introduced. Finally, the available techniques for wastewater treatment, challenges and future perspectives on the recent progress were highlighted. The suggestions in this article will facilitate the development of novel on-site methods for removing emerging pollutants from pharmaceutical effluents and commercial enterprises.
Global production of shellfish aquaculture is steadily increasing owing to the growing market demands for shellfish. The intensification of shellfish aquaculture to maximize production rate has led to increased generation of aquaculture waste streams, particularly the effluents and shellfish wastes. If not effectively managed, these wastes could pose serious threats to human health and the ecosystem while compromising the overall sustainability of the industry. The present work comprehensively reviews the source, composition, and environmental implications of shellfish wastes and aquaculture wastewater. Moreover, recent advancements in the valorization of shellfish wastes into value-added biochar via emerging thermochemical and modification techniques are scrutinized. The utilization of the produced biochar in removing emerging pollutants from aquaculture wastewater is also discussed. It was revealed that shellfish waste-derived biochar exhibits relatively higher adsorption capacities (300-1500 mg/g) compared to lignocellulose biochar (<200 mg/g). The shellfish waste-derived biochar can be effectively employed for the removal of various contaminants such as antibiotics, heavy metals, and excessive nutrients from aquaculture wastewater. Finally, future research priorities and challenges faced to improve the sustainability of the shellfish aquaculture industry to effectively support global food security are elaborated. This review envisages that future studies should focus on the biorefinery concept to extract more useful compounds (e.g., carotenoid, chitin) from shellfish wastes for promoting environmental-friendly aquaculture.
Rhodamine B (RhB) dye used in the textile industries is associated with carcinogenic and neurotoxic effects with a high potential to cause a variety of human diseases. Semiconductor photocatalysts synthesised through agriculture waste extracts exhibited high efficiency for RhB removal. The current review aimed to explore the efficiency and mechanism of RhB degradation using different photocatalysts that have been used in recent years, as well as the effect of various factors on the removal process. Zinc oxide nanoparticles (ZnO NPs) synthesised from plant extract is the most effective for the RhB degradation with the efficiency reaching 100% after 210 min. The photocatalysis process depends on the pH because pH changes the balance of water dissociation, which impacts the formation of hydroxyl radicals and the surface load of the catalyst. Analysis using Jupyter Notebook revealed a strong correlation between the concentration of ZnO NPs and the photocatalysis efficiency (R = 0.72). These findings reveal that man-sized photocatalysts have a high potential for removing RhB from the wastewater.