Displaying publications 1 - 20 of 23 in total

Abstract:
Sort:
  1. Halim, N. R. A., Sarbon, N. M.
    MyJurnal
    The study aims to determine the optimized condition of eel protein hydrolysate (EPH)
    produced using alcalase. The proximate compositions of eel flesh were determined as well.
    Enzymatic hydrolysis conditions were optimized using response surface methodology (RSM)
    by applying four factors, 3-levels Central Composite Design (CCD) with six centre points. The
    model equation was proposed with regards to the time (60min, 120min, 180min), temperature
    (40°C, 50°C, 60°C), pH (7, 8, 9) and enzyme concentration (1%, 2%, 3%). The optimum of
    hydrolysis condition that be suggested to obtain the optimum yield, degree of hydrolysis (DH)
    and antioxidant activity were 84.02 min, 50.18°C, pH 7.89 and 2.26% [enzyme]. The predicted
    response values using quadratic model were 10.03% for yield, 83.23% for DH and 89.24%
    for antioxidant activity. The chemical composition determination showed that the protein
    content increased by more than 5-fold (16.88% to 98.53%) while the fat content was decreased
    by 96.48% after hydrolysis. Hydrolysis process had significantly increased the amount of
    both hydrophilic (serine and threonine) and hydrophobic amino acids (valine, isoleucine,
    phenylalanine, methionine) which contributed to the antioxidant activity of hydrolyzed eel
    protein. The enzymatic hydrolysis of eel protein had improved the protein content of EPH with
    potential as new natural antioxidant.
  2. Ismail, N. A., Ab. Karim, M. S., Othman, M., Abd. Halim, N.
    MyJurnal
    The central question to be examined in this study is associated with the value of the Malays traditional culinary practices of Malay chef in preparing the traditional food in Malaysian hotels. Present understanding highlighted that hotels are giving high priority on their superior services, such as luxury accommodations and intimate hospitalities. As such, promoting local foods in their dining establishment has taken a back seat. Research from past scholars indicated that hotel in Malaysia can be the one stop center for the local and international tourists to get the first hand information about local food specialities. On the hindsight, very limited efforts have been put into practice on the promotions of local food especially Malay cuisines in hotels. Main issue such as mass-produced Malay cuisines in the commercial kitchens, for example, should be highlighted to ensure that hotels are not jeopardizing the originality of traditional food preparations. Therefore, a qualitative reasearch focusing in in-depth interview with 10 Malay chefs was conducted in hotels around the Klang Valley. The results are so profound that majority of the Malay chefs under study shared similar understandings on technology advancements and modernizations that have taken place in their daily food preparations. Another finding revealed that one of the most challenging factors in preventing the Malay chefs to prepare the Malay food as it has been done traditionally is the attitude and awareness of the young generations to understand the values in traditional culinary practices. This study concludes with suggestion that aggressive knowledge sharing and information dissemination among the Malay chefs in hotels are needed to effectively market the traditional Malay food.
  3. Ali N, Halim NS, Jusoh A, Endut A
    Bioresour Technol, 2010 Mar;101(5):1459-65.
    PMID: 19786347 DOI: 10.1016/j.biortech.2009.08.070
    The focus of this research is to study the potential of nanofiltration membrane technology in removing ammonia-nitrogen from the aquaculture system. One of the major fabrication parameters that directly affect the separation performance is shear rate or casting rate during membrane fabrication. In this study, asymmetric polyethersulfone (PES) nanofiltration membranes were prepared at five different shear rates within the range of 67-400 s(-1). Membrane productivity and separation performance were assessed via pure water, salt and ammonia-nitrogen permeation experiments, and their structural properties were determined by employing the combination of the irreversible thermodynamic (IT) model, solution diffusion model, steric hindrance pore (SHP) model and Teorell-Meyers (TMS) model. The study reveals that the alteration of shear rate enormously affects the membrane morphology and structural parameters, hence subsequently significantly influencing the membrane performance. It was found that, membrane produced at the shear rate 200 s(-1) or equivalent to 10s of casting speed during membrane fabrications managed to remove about 68% of ammonia-nitrogen, in which its separation performance is the most favourable by means of highest flux and rejection ability towards unwanted solutes. Besides, from the research findings, nano-membrane technology is a potential candidate for the treatment of aquaculture wastewater.
  4. Halim NA, Plutzer J, Bakheit MA, Karanis P
    Vet Parasitol, 2008 Apr 15;152(3-4):325-9.
    PMID: 18289793 DOI: 10.1016/j.vetpar.2007.12.035
    Fifty faecal samples from diarrheic calves between 1 and 6 months old were collected per rectum from 5 farms around Petaling District in Selangor, Malaysia for Cryptosporidium species detection and genotyping investigation. Oocysts were purified using sedimentation and gradient centrifugation, then examined by immunofluorescence assay (IFAT). Genomic DNA was extracted from all samples and nested PCR was performed to amplify the SSU rRNA gene. Eighteen samples (36%) were positive for Cryptosporidium species by PCR. The sequence and phylogenetic analysis of 14 isolates indicated that Cryptosporidium parvum was most common (11 isolates) followed by Cryptosporidium deer-like genotype (3 isolates). The present work reports the first data on Cryptosporidium genotyping from cattle in Malaysia.
  5. Halim N, Kuntom A, Shinde R, Banerjee K
    J AOAC Int, 2020 Sep 01;103(5):1237-1242.
    PMID: 33241391 DOI: 10.1093/jaoacint/qsaa041
    BACKGROUND: Indaziflam (IND) is a herbicide that is used in palm oil plantations for broad spectrum management of weeds. Until now, no validated method has been available for residue estimation of this herbicide in palm oil products.

    OBJECTIVE: In this study, we report a rapid method for the residue analysis of IND and its metabolites, viz., IND-carboxylic acid, diaminotriazine, and triazine indanone in a wide range of palm oil matrices using liquid chromatography-tandem mass spectrometry (LC-MS/MS).

    METHOD: The optimized sample preparation workflows included two options: (1) acetonitrile extraction (QuEChERS workflow), followed by freezing at -80°C and (2) acetonitrile extraction, followed by cleanup through a C18 solid phase extraction (SPE) cartridge. The optimized LC runtime was 7 min. All these analytes were estimated by LC-MS/MS multiple reaction monitoring.

    RESULTS: Both sample preparation methods provided similar method performance and acceptable results. The limit of quantification (LOQ) of IND, IND-carboxylic acid, and triazine indanone was 0.001 mg/kg. For diaminotriazine, the LOQ was 0.005 mg/kg. The method accuracy and precision complied with the SANTE/12682/2019 guidelines of analytical quality control.

    CONCLUSIONS: The potentiality of the method lies in a high throughput analysis of IND and its metabolites in a single chromatographic run with high selectivity and sensitivity. Considering its fit-for-purpose performance, the method can be implemented in regulatory testing of IND residues in a wide range of palm oil matrices that are consumed and traded worldwide.

    HIGHLIGHTS: This work has provided a validated method for simultaneous residue analysis of indaziflam and its metabolites in crude palm oil and its derived matrices with high sensitivity, selectivity, and throughput.

  6. Shinde R, Halim N, Banerjee AK
    J AOAC Int, 2020 Nov 01;103(6):1528-1533.
    PMID: 33247748 DOI: 10.1093/jaoacint/qsaa066
    BACKGROUND: Glyphosate and glufosinate are broad-spectrum herbicides which are frequently used in palm oil plantations for weed control. Metabolites of these herbicides are known to have environmental and food safety implications. As there is no validated method for multiresidue testing of these herbicides and their metabolites in palm oil products, a new method was needed for the purpose of regulatory analysis.

    OBJECTIVE: In this study, we endeavored to develop a rapid method for multiresidue analysis of glyphosate (+aminomethylphosphonic acid) and glufosinate (+3-methylphosphinicopropionic acid and N-acetyl-glufosinate) in refined and crude palm oil matrices using liquid chromatography (LC) tandem mass spectrometry (MS/MS).

    METHOD: The optimized sample preparation workflow included extraction of refined or crude palm oil (10 g) with acidified water (0.1 M HCl), cleanup by phase separation with dichloromethane, and analysis by LC-MS/MS with multiple reaction monitoring.

    RESULTS: The use of a Torus-DEA LC column ensured simultaneous analysis of these compounds within a runtime of 10 min. The LOQ of these analytes was 0.01 mg/kg, except that of aminomethylphosphonic acid which was 0.02 mg/kg. The method sensitivity complied with the national maximum residue limits of Malaysia and the European Union. Also, the method selectivity, sensitivity, accuracy, and precision were aligned with the SANTE/12682/2019 guidelines of analytical quality control.

    CONCLUSIONS: The potentiality of the optimized method lies in a high throughput direct analysis of glyphosate and glufosinate with their metabolites in a single chromatographic run. The method is fit for purpose for regulatory testing of these residues in a broad range of palm oil matrices.

    HIGHLIGHTS: The study reports for the first time a validated method for simultaneous analysis of glyphosate, glufosinate, and their metabolites in a range of palm oil products. The method did not require a derivatization step and provided a high throughput analysis of these compounds with satisfactory selectivity, sensitivity, accuracy, and precision.

  7. Ab Halim N, Esa R, Chew HP
    BMC Oral Health, 2018 01 12;18(1):11.
    PMID: 29329566 DOI: 10.1186/s12903-017-0451-9
    BACKGROUND: The objective of this study was to determine the prevalence and severity of general tooth wear (GTW), i.e. tooth wear irrespective of etiology and erosive tooth wear (ETW), i.e. tooth wear predominantly due to erosion; and also to investigate the relationship between ETW and dental caries experience in 16-year-old adolescents in Kuantan, Malaysia.

    METHODS: A multi-staged cluster sampling method was employed. A total of 598 16-year-old adolescents participated in this study. Participants' demographic profile was assessed through a self-administered questionnaire. Clinical examinations were carried out under standardized conditions by a single examiner. The level of GTW was recorded using the modified Smith and Knight's Tooth Wear Index (TWI) whilst ETW were recorded using the Basic Erosive Wear Examination (BEWE) index. This index was developed to record clinical findings and assist in the decision-making process for the management of erosive tooth wear. Dental caries was recorded using the D3MFT index whereby D3 denotes obvious dental decay into dentine detected visually.

    RESULTS: The prevalence of GTW, ETW and dental caries, i.e. percentage of individuals found to have at least one lesion, was 99.8%, 45.0% and 27.8% respectively. Two thirds of affected teeth with GTW were observed to have a TWI score of 1 whereas almost all of the affected teeth with ETW had a BEWE score of 2. The mean D3MFT was 0.62 (95% CI 0.50, 0.73) with Decayed (D) teeth being the largest component, mean D3T was 0.36 (95% CI 0.30, 0.43). There was no significant association between socio-demographic factors and prevalence of ETW. Logistic regression analysis also showed no significant relationship between the prevalence of ETW and D3MFT (p > 0.05).

    CONCLUSIONS: Almost all adolescents examined had GTW but they were mainly early lesions. However, nearly half were found to have ETW of moderate severity (BEWE score 2). No significant relationship between the occurrence of erosive tooth wear and caries was observed in this population.

  8. Samsudin NA, Halim NRA, Sarbon NM
    J Food Sci Technol, 2018 Nov;55(11):4608-4614.
    PMID: 30333657 DOI: 10.1007/s13197-018-3399-0
    The aim of this study is to investigate the effect of pH levels on functional properties of various molecular weights of eel (Monopterus sp.) protein hydrolysate (EPH). The eel was enzymatically hydrolyzed and fractionated through membranes filter (10 kDa, 5 kDa and 3 kDa). The foaming capacity and stability, emulsifying capacity and stability index, water holding capacity and fat binding capacity between pH 2 and 10 were determined. The 5 kDa EPH was found to have the highest foaming capacity at pH 2, pH 4 and pH 6, and foaming stability and emulsifying activity index at all pH levels, except pH 8 and fat binding capacity at pH 2, as compared to 10 kDa and 3 kDa EPH fractions. The 10 kDa EPH had the highest emulsifying stability index and water holding capacity at all pH levels. This study shows that the EPH fractions at low pH level had high foaming and oil binding capacity, while at neutral pH, the fractions had high foaming stability and water holding capacity. These properties are important in making whipped cream, mousse and meringue. In contrast, EPH fractions demonstrated strong emulsifying properties at high pH levels and show potential as an emulsifier for breads, biscuits and frozen desserts.
  9. Uda MNA, Gopinath SCB, Hashim U, Halim NH, Parmin NA, Uda MNA, et al.
    3 Biotech, 2021 May;11(5):205.
    PMID: 33868892 DOI: 10.1007/s13205-021-02740-9
    This paper describes the synthesis of graphene-based activated carbon from carbonaceous rice straw fly ash in an electrical furnace and the subsequent potassium hydroxide extraction. The produced graphene has a proper morphological structure; flakes and a rough surface can be observed. The average size of the graphene was defined as up to 2000 nm and clarification was provided by high-resolution microscopes (FESEM and FETEM). Crystallinity was confirmed by surface area electron diffraction. The chemical bonding from the graphene was clearly observed, with -C=C- and O-H stretching at peaks of 1644 cm-1 and 3435 cm-1, respectively. Impurities in the graphene were found using X-ray photoelectron spectroscopy and energy dispersive X-ray spectroscopy. The measured size, according to zeta-potential analysis, was 8722.2 ± 25 nm, and the average polydispersity index was 0.576. The stability of the mass reduction was analyzed by a thermogravimetric at 100 °C, with a final reduction of ~ 11%.
  10. Halim NSS, Ch'ng ES, Kardia E, Ali SA, Radzi R, Yahaya BH
    Stem Cell Rev Rep, 2019 02;15(1):112-125.
    PMID: 30178289 DOI: 10.1007/s12015-018-9844-7
    BACKGROUND: The aim of this study was to investigate the effects of MSCs and MSC-expressing ANGPT1 (MSC-pANGPT1) treatment via aerosolisation in alleviating the asthma-related airway inflammation in the rabbit model.

    METHODS: Rabbits were sensitised and challenged with both intraperitoneal injection and inhalation of ovalbumin (Ova). MSCs and MSC-pANGPT1 cells were aerosolised into rabbit lungs using the MicroSprayer® Aerosolizer Model IA-1B 48 h after injury. The post mortem was performed 3 days following cell delivery. Histopathological assessments of the lung tissues and inflammatory response were quantitatively scored following treatments.

    RESULT(S): Administration of aerosolised MSCs and MSC-pANGPT1 were significantly reduced inflammation of the airways (p 

  11. Sukor NF, Jusoh R, Kamarudin NS, Abdul Halim NA, Sulaiman AZ, Abdullah SB
    Ultrason Sonochem, 2020 Apr;62:104876.
    PMID: 31796331 DOI: 10.1016/j.ultsonch.2019.104876
    Phenolic acids of oak gall were extracted using ultrasonic-probe assisted extraction (UPAE) method in the presence of ionic liquid. It was compared with classical ultrasonic-bath assisted extraction (CUBAE) and conventional aqueous extraction (CAE) method, with and without the presence of ionic liquid. Remarkably, the UPAE method yielded two-fold higher extraction yield with the presence of ionic liquid, resulting 481.04 mg/g for gallic acids (GA) and 2287.90 mg/g for tannic acids (TA), while a decreased value of 130.36 mg/g for GA and 1556.26 mg/g for TA were resulted with the absence of ionic liquid. Intensification process resulted the highest yield of 497.34 mg/g and 2430.48 mg/g for GA and TA, respectively, extracted at temperature 50 °C with sonication intensity of 8.66 W/cm2 and 10% duty cycle, diluted in ionic liquid, 1-Butyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide, [Bmim][Tf2N] at concentration of 0.10 M with sample-to-solvent ratio 1:10 for 8 h. Peleg's model successfully predicted the UPAE process confirming that extraction capacity is the controlling factor in extracting phenolic acids. Hence, it can be concluded that UPAE method and ionic liquid have synergistic effect as it effectively enhanced the extraction efficiency to increase the bioactive constituents yield.
  12. Li A, Abrahim A, Islam M, Mejías E, Hafizati Abdul Halim N, Frew R, et al.
    Food Chem, 2024 Feb 15;434:137451.
    PMID: 37748289 DOI: 10.1016/j.foodchem.2023.137451
    One of the most common types of adulteration of honey involves the addition of invert sugar syrups. A new method was developed to measure the stable isotope ratios of carbon and carbon-bound non-exchangeable (CBNE) hydrogen from specific molecular positions in fructose and glucose in honey. This was achieved through periodate oxidation of the sugars to produce formaldehyde, followed by reaction with ammonia to form hexamethylenetetramine (HMT). The preparation was simplified, optimized, and validated by isotopic analysis of replicate syntheses of HMT from fructose, glucose, sugar syrup and a representative authentic honey sample. The optimized method had a repeatability standard deviation from 1.5‰ to 3.0‰ and from 0.1‰ to 0.4‰ for δ2H and δ13C, respectively. This methodology has advantages over alternative isotopic methods, for measuring CBNE hydrogen isotope ratios in sugars, in terms of time, sensitivity and operability and offers a complementary method to differentiate authentic honey from invert sugar syrups.
  13. Nurazzi NM, Abdullah N, Demon SZN, Halim NA, Mohamad IS
    Polymers (Basel), 2021 Jun 09;13(12).
    PMID: 34207577 DOI: 10.3390/polym13121916
    Non-covalent functionalisation of the carbon nanotube (CNT) sidewall through polymer wrapping is the key strategy for improving well-dispersed CNTs without persistent alteration of their electronic properties. In this work, the effect of reaction time on regioregular poly (3-hexylthiophene-2,5-diyl) (P3HT)-wrapped hydroxylated multi-walled CNT (MWCNT-OH) nanocomposites was investigated. Five different reaction times (24, 48, 72, 96, and 120 h) were conducted at room temperature in order to clearly determine the factors that influenced the quality of wrapped MWCNT-OH. Morphological analysis using Field Emission Scanning Electron Microscopic (FESEM) and High-Resolution Transmission Electron Microscope (HRTEM) analysis showed that P3HT successfully wrapped the MWCNT-OH sidewall, evidenced by the changes in the mean diameter size of the nanocomposites. Results obtained from Raman spectroscopy, X-ray Photoelectron Spectroscopy (XPS) as well as Thermogravimetric Analysis (TGA) showed a significant effect of the wrapped polymer on the CNT sidewall as the reaction time increased. Overall, the method used during the preparation of P3HT-wrapped MWCNT-OH and the presented results significantly provided a bottom-up approach to determine the effect of different reaction times on polymer wrapping to further expand this material for novel applications, especially chemical sensors.
  14. Abdul Halim N, Md Yassin M, Mohamad Ali ND, Miptah HN
    Am J Case Rep, 2024 Sep 11;25:e944399.
    PMID: 39256984 DOI: 10.12659/AJCR.944399
    BACKGROUND Eagle syndrome is an uncommon medical illness that can manifest as neck pain in primary care. It results from an abnormally unilateral or bilateral long styloid process that may compress and affect adjacent structures, which leads to the symptoms. Classical Eagle syndrome has been commonly reported, but this case highlights the uncommon involvement of autonomic nerve dysfunction. CASE REPORT This case report details a 43-year-old woman with chronic neck pain for 5 years who saw numerous medical professionals and underwent 8 physiotherapy sessions. Marginal improvement of her neck pain and recent development of imbalance and a floating sensation prompted escalation of radiological imaging that eventually led to the diagnosis of Eagle syndrome. She was subsequently subjected to tonsillectomy and styloidectomy to address the sources of her neck pain. CONCLUSIONS Neck pain is a common complaint in primary care, but Eagle syndrome is often overlooked due to its complex symptoms, which mimic other conditions resulting in missed diagnoses and prolonged diagnostic evaluations. To improve patient care and outcomes, primary care physicians should consider Eagle syndrome when evaluating neck pain. This involves taking a detailed clinical history, conducting a thorough physical examination, using appropriate imaging techniques, and knowing the treatment options. By considering this potential diagnosis, primary care physicians, other healthcare professionals, and physical therapists play an important role in referring these patients to an otorhinolaryngologist or a maxillofacial surgeon for a comprehensive evaluation and management.
  15. Md-Muziman-Syah MM, Muzir NS, Abdul Mutalib H, Ab Halim N
    BMC Ophthalmol, 2021 Oct 25;21(1):378.
    PMID: 34696755 DOI: 10.1186/s12886-021-02145-5
    BACKGROUND: The Quality of Life Impact Refractive Correction (QIRC) questionnaire is a Rasch-validated instrument to assess the quality of life of ametropes with refractive correction. The original QIRC was validated in the United Kingdom. This study aimed to validate the Malay version of the QIRC among refractive correction wearers in Malaysia using Rasch analysis.

    METHODS: The original 20-item QIRC was forward-backward translated into Malay in preparation for the Pilot Malay QIRC. The pilot version was pre-tested on 105 spectacle/contact lens-corrected myopes, and the results were reviewed and cross-culturally adapted to produce the Final Malay QIRC. The final version was self-administered to a new sample of 304 participants. A Rasch analysis was conducted to evaluate the items and response categories of the Pilot and the Final Malay QIRC. Test-retest reliability was also analysed on the Final Malay QIRC.

    RESULTS: Based on the pre-test findings, Rasch analysis revealed a multidimensional scale (functional scale [Items 1 to 13] and emotional scale [Items 14 to 20], which were separated in subsequent analysis), unordered response categories for the functional scale (Category 3 was collapsed into Category 2), one misfit item (Item 3 was removed) and six items required modification (Items 4, 6 to 9, and 12 were reworded and cross-culturally adapted). In the Final Malay QIRC, both the functional and emotional scales had ordered response categories, good person reliability (functional, 0.80; emotional, 0.81) and separation index (functional, 2.01; emotional, 2.06), well-targeted items (targeting precision: functional, 0.28 logits; emotional, 0.08 logits), and satisfactory fit statistics (infit and outfit mean square were less than 1.50 for all items). A noticeable differential item functioning (DIF) between genders was found in Item 18 (DIF contrast, 0.40 logits; p = 0.04). Test-retest reliability analysis demonstrated a high intraclass correlation coefficient (0.94) and Cronbach's alpha (0.97) with a coefficient of repeatability of ±8.14 units.

    CONCLUSIONS: The Malay-translated version of the QIRC has good psychometric characteristics for assessing the quality of life of refractive correction wearers in Malaysia. This translated and cross-culturally adapted Malay QIRC is a valid and reliable instrument that can be used in routine clinical practice.

  16. Uda MNA, Gopinath SCB, Hashim U, Halim NH, Parmin NA, Afnan Uda MN, et al.
    Prep Biochem Biotechnol, 2021;51(1):86-95.
    PMID: 32713293 DOI: 10.1080/10826068.2020.1793174
    A chemical method to synthesize amorphous silica nanoparticles from the incinerated paddy straw has been introduced. The synthesis was conducted through the hydrolysis by alkaline-acidic treatments. As a result, silica particles produced with the sizes were ranging at 60-90 nm, determined by high-resolution microscopy. The crystallinity was confirmed by surface area electron diffraction. Apart from that, chemical and diffraction analyses for both rice straw ash and synthesized silica nanoparticles were conducted by X-ray diffraction and Fourier-transform infrared spectroscopy. The percentage of silica from the incinerated straw was calculated to be 28.3. The prominent surface chemical bonding on the generated silica nanoparticles was with Si-O-Si, stretch of Si-O and symmetric Si-O bonds at peaks of 1090, 471, and 780 cm-1, respectively. To confirm the impurities of the elements in the produced silica, were analyzed using X-ray photoelectron spectroscopy and energy dispersive X-ray spectroscopy. The stability of silica nanoparticles was investigated using thermogravimetric analysis and zeta potential. The measured size from zeta potential analysis was 411.3-493 nm and the stability of mass reduction was located at 200 °C with final amount of mass reduced ∼88% and an average polydispersity Index was 0.195-0.224.
  17. Uda MNA, Gopinath SCB, Hashim U, Halim NH, Parmin NA, Uda MNA, et al.
    Sci Rep, 2021 Jul 19;11(1):14688.
    PMID: 34282233 DOI: 10.1038/s41598-021-94145-0
    Arsenic is a major global threat to the ecosystem. Here we describe a highly accurate sensing platform using silica nanoparticles/graphene at the surface of aluminum interdigitated electrodes (Al IDE), able to detect trace amounts of arsenic(III) in rice grain samples. The morphology and electrical properties of fabricated Al IDEs were characterized and standardized using AFM, and SEM with EDX analyses. Micrometer scale Al IDEs were fabricated with silicon, aluminum, and oxygen as primary elements. Validation of the bare Al IDE with electrolyte fouling was performed at different pH levels. The sensing surface was stable with no electrolyte fouling at pH 7. Each chemical modification step was monitored with current-volt measurement. The surface chemical bonds were characterized by fourier transform infrared spectroscopy (FTIR) and revealed different peaks when interacting with arsenic (1600-1000 cm-1). Both silica nanoparticles and graphene presented a sensitive limit of detection as measured by slope calibration curves at 0.0000001 pg/ml, respectively. Further, linear regression was established using ΔI (A) = 3.86 E-09 log (Arsenic concentration) [g/ml] + 8.67 E-08 [A] for silica nanoparticles, whereas for graphene Y = 3.73 E-09 (Arsenic concentration) [g/ml] + 8.52 E-08 on the linear range of 0.0000001 pg/ml to 0.01 pg/ml. The R2 for silica (0.96) and that of graphene (0.94) was close to the maximum (1). Modification with silica nanoparticles was highly stable. The potential use of silica nanoparticles in the detection of arsenic in rice grain extract can be attributed to their size and stability.
  18. Al-Japairai K, Hamed Almurisi S, Almonem Doolaanea A, Mahmood S, Alheibshy F, Alobaida A, et al.
    Int J Pharm, 2023 Feb 05;632:122571.
    PMID: 36587776 DOI: 10.1016/j.ijpharm.2022.122571
    Taste refers to those sensations perceived through taste buds on the tongue and oral cavity. The unpleasant taste of drugs leads to the refusal of taking the medicine in the paediatric population. It is widely known that a pharmaceutical product's general acceptability is the result of numerous contributing components such as swallowability, palatability (taste, flavour, texture, and mouthfeel), appearance, ease of administration, and patient characteristics. Multiparticulate as a dosage form is a platform technology for overcoming paediatrics' incapacity to swallow monolithic dosage forms, masking many medications' inherent nasty taste, and overcoming the obstacles of manufacturing a commercially taste masked dosage form. This review will discuss the considerations that must be taken into account to prepare taste masked multiparticulate dosage forms in the best way for paediatric use.
  19. Alhabshi SM, Rahmat K, Abdul Halim N, Aziz S, Radhika S, Gan GC, et al.
    Ultrasound Med Biol, 2013 Apr;39(4):568-78.
    PMID: 23384468 DOI: 10.1016/j.ultrasmedbio.2012.10.016
    The purpose of this study was to evaluate the diagnostic value of qualitative and semi-quantitative assessment of ultrasound elastography in differentiating between benign and malignant breast lesions. This prospective study was conducted in two tertiary medical centers. Consecutive B-mode ultrasound and real-time elastographic images were obtained for 67 malignant and 101 benign breast lesions in 168 women. Four experienced radiologists analyzed B-mode ultrasound alone and B-mode ultrasound combined with elastography independently. Conventional ultrasound findings were classified according to the American College of Radiology Breast Imaging Reporting and Data System classification. The elastographic assessment was based on qualitative and semi-quantitative parameters (i.e., strain pattern, width ratio, strain ratio). The sensitivity and specificity of combined elastography and conventional ultrasound were significantly higher than that of conventional ultrasound alone. The sensitivity, specificity, positive predictive value and negative predictive value was 97%, 61.4%, 62.5% and 96.8%, respectively, for conventional ultrasound and 100%, 93%, 99% and 90%, respectively, for combined technique. The semi-quantitative assessment with strain ratio and width ratio in elastography were the most useful parameters in differentiating between benign and malignant breast lesions. Cut-off point values for width ratio of more than 1.1 and strain ratio of more than 5.6 showed a high predictive value of malignancy with specificities of 84% and 76%, respectively (p 
  20. Che Sulaiman IS, Chieng BW, Osman MJ, Ong KK, Rashid JIA, Wan Yunus WMZ, et al.
    Mikrochim Acta, 2020 01 15;187(2):131.
    PMID: 31940088 DOI: 10.1007/s00604-019-3893-8
    This review (with 99 refs.) summarizes the progress that has been made in colorimetric (i.e. spectrophotometric) determination of organophosphate pesticides (OPPs) using gold and silver nanoparticles (NPs). Following an introduction into the field, a first large section covers the types and functions of organophosphate pesticides. Methods for colorimetric (spectrophotometric) measurements including RGB techniques are discussed next. A further section covers the characteristic features of gold and silver-based NPs. Syntheses and modifications of metal NPs are covered in section 5. This is followed by overviews on enzyme inhibition-based assays, aptamer-based assays and chemical (non-enzymatic) assays, and a discussion of specific features of colorimetric assays. Several Tables are presented that give an overview on the wealth of methods and materials. A concluding section addresses current challenges and discusses potential future trends and opportunities. Graphical abstractSchematic representation of organophosphate pesticide determinations based on aggregation of nanoparticles (particular silver or gold nanoparticles). This leads to a color change which can be determined visually and monitored by a red shift in the absorption spectrum.
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links