Displaying publications 1 - 20 of 37 in total

Abstract:
Sort:
  1. Development, characterization and commercial application of palm based dihydroxystearic acid and its derivatives: an overview
    Koay GF, Chuah TG, Zainal-Abidin S, Ahmad S, Choong TS
    J Oleo Sci, 2011;60(5):237-65.
    PMID: 21502724
    Hydroxyl fatty acids and their derivatives are of high value due to their wide range of industrial application, including cosmetic, food, personal care and pharmaceutical products. Realizing the importance of hydroxyl fatty acids, and yet due to the absence of the conventional starting raw materials, Malaysia has developed 9,10-dihydroxystearic acid (9,10-DHSA) and its derivatives from locally abundant palm based oils. The aim of this article is to provide a general description of the works that have thus far being done on palm based 9,10-DHSA: starting from its conception and production from commercial grade palm based crude oleic acid via epoxidation and hydrolysis, purification through solvent crystallization and characterization through wet and analytical chemistry, moving on to developmental works done on producing its derivatives through blending, esterification, amidation and polymerization, and completing with applications of 9,10-DHSA and its derivatives, e.g. DHSA-stearates and DHSA-estolides, in commercial products such as soaps, deodorant sticks and shampoos. This article incorporates some of the patent filed technological knowhow on 9,10-DHSA and its derivatives, and will also point out some of the shortcomings in previously published documents and provide some recommendations for future research works in mitigating these shortcomings.
    Matched MeSH terms: Stearic Acids/chemical synthesis*; Stearic Acids/isolation & purification; Stearic Acids/chemistry*
  2. Fulltext Physicochemical properties of margarines enriched with medium- and long-chain triacylglycerol
    Arifin, N., Cheong, L.Z., Koh, S.P., Long, K., Tan, C.P., Yusoff, M.S.A., et al.
    ASM Science Journal, 2010;4(2):113-122.
    MyJurnal
    Several binary and ternary medium- and long-chain triacylglycerol (MLCT)-enriched margarine formulations were examined for their solid fat content, heating profile, polymorphism and textural properties. MLCT feedstock was produced through enzymatic esterification of capric and stearic acids with glycerol. The binary formulations were produced by mixing MLCT feedstock blend (40%–90%) and palm olein (10%–60%) with 10% increments (w/w). Solid fat profiles of commercial margarines were used as a reference to determine the suitability of the formulations for margarine production. The solid fat content of the binary formulations of MO 82 and MO 91 (M, MLCT, O, palm olein) were similar to the commercial margarines at 25°C which met the basic requirement for efficient dough consistency. Ternary formulations using reduced MLCT feedstock blend proportion (from 80%–90% to 60%–70%) were also developed. The reduction of MLCT feedstock blend was
    done as it had the highest production cost (3USD/kg) in comparison to palm olein (0.77USD/kg) and palm stearin (0.7USD/kg). The proportions of 5%–15% of palm stearin were substituted with palm olein in MO 64 and MO 73 (M, MLCT; O, palm olein) formulations with 5% increment (w/w). As a result, MOS 702010 and MOS 603010 (M, MLCT; O, palm olein; S, palm stearin) margarine formulations showed similar SFC % to the commercial margarines at 25ºC. These formulations were subsequently chosen to produce margarines. The onset melting and complete melting points of MLCT-enriched margarine formulations were high (51.04ºC –57.93ºC) due to the presence of a high amount of long chain saturated fatty acids. Most of the formulations showed β΄- crystals. MOS 702010 was selected as the best formulation due to values for textural parameters comparable (P
    Matched MeSH terms: Stearic Acids
  3. Fulltext Preparation and characterization of polyhydroxybutyrate/polycaprolactone nanocomposites
    Liau CP, Bin Ahmad M, Shameli K, Yunus WM, Ibrahim NA, Zainuddin N, et al.
    ScientificWorldJournal, 2014;2014:572726.
    PMID: 24600329 DOI: 10.1155/2014/572726
    Polyhydroxybutyrate (PHB)/polycaprolactone (PCL)/stearate Mg-Al layered double hydroxide (LDH) nanocomposites were prepared via solution casting intercalation method. Coprecipitation method was used to prepare the anionic clay Mg-Al LDH from nitrate salt solution. Modification of nitrate anions by stearate anions between the LDH layers via ion exchange reaction. FTIR spectra showed the presence of carboxylic acid (COOH) group which indicates that stearate anions were successfully intercalated into the Mg-Al LDH. The formation of nanocomposites only involves physical interaction as there are no new functional groups or new bonding formed. X-ray diffraction (XRD) and transmission electron microscopy (TEM) indicated that the mixtures of nanocomposites are intercalated and exfoliated types. XRD results showed increasing of basal spacing from 8.66 to 32.97 Å in modified stearate Mg-Al LDH, and TEM results revealed that the stearate Mg-Al LDH layers are homogeneously distributed in the PHB/PCL polymer blends matrix. Enhancement in 300% elongation at break and 66% tensile strength in the presence of 1.0 wt % of the stearate Mg-Al LDH as compare with PHB/PCL blends. Scanning electron microscopy (SEM) proved that clay improves compatibility between polymer matrix and the best ratio 80PHB/20PCL/1stearate Mg-Al LDH surface is well dispersed and stretched before it breaks.
    Matched MeSH terms: Stearic Acids/chemistry
  4. Moldability characteristics of 3 mol% Yttria stabilized Zirconia feedstock for micro-powder injection molding process
    Hafizawati Zakaria, Norhamidi Muhamad, Abu Bakar Sulong, Mord Halim Irwan Ibrahim, Farhana Foudzi
    Sains Malaysiana, 2014;43:129-136.
    Micro powder injection molding (vim) is a promising process that may satisfy the demand on miniaturization parts to micro domain in mass production with low manufacturing cost. Three mol% yttria stabilized zirconia (Ysz) with nano-sized powder and binder system consists of polyethylene glycol (PEG), polymethyl methacrylate (PMMA) and stearic acid (sA) were used. Nano-size powders with higher surface area generally require more binder to form a feedstock. As such, determination of the optimum powder loading of the feedstock for 1UPIM process is important. The rheological characteristics of different YSZ feedstocks with powder loading of 52 53 and 54 vol.% were investigated in terms of flow behavior as a function of viscosity and shear rate. Fairly low values of flow behavior exponent ranging from 025 to 0.39 (n<1) resulted in pseudoplastic flow behavior of the examined Yszfeedstock. The 52 vol.% feedstock exhibited the lowest viscosity resulting in highest activation energy and lowest moldability index of 1.862x10-6, while the 54 vol.% feedstock regardless to its high viscosity, yielded a low activation energy of 4.14 kJImol and high moldability index of 4.59x10-6. Based on rheological properties obtained, a powder loading of 54 vol.% has desirable feedstock characteristics for iumm process and exhibited molding ability for micro detail filling. The relationship between the optimum rheological properties obtained and the actual injection process was also determined. The results showed that the green parts were able to be injected without defects such as short shot or flashing.
    Matched MeSH terms: Stearic Acids
  5. Capillary electrophoresis with capacitively coupled contactless conductivity detection for the determination of cis/trans isomers of octadec-9-enoic acid and other long chain fatty acids
    Wong YF, Saad B, Makahleh A
    J Chromatogr A, 2013 May 17;1290:82-90.
    PMID: 23578483 DOI: 10.1016/j.chroma.2013.03.014
    A capillary electrophoresis (CE)-capacitively coupled contactless conductivity detection (C(4)D) method for the simultaneous separation of eleven underivatized fatty acids (FAs), namely, lauric, myristic, tridecanoic (internal standard), pentadecanoic, palmitic, stearic, oleic, elaidic, linoleic, linolenic and arachidic acids is described. The separation was carried out in normal polarity mode at 20 °C, 30 kV and using hydrodynamic injection (50 mbar for 1 s). The separation was achieved in a bare fused-silica capillary (70 cm × 75 μm i.d.) using a background electrolyte of methyl-β-cyclodextrin (~6 mM) and heptakis-(2,3,6-tri-O-methyl)-β-cyclodextrin (~8 mM) dissolved in a mixture of Na2HPO4/KH2PO4 (5 mM, pH 7.4):ACN:MeOH:n-octanol (3:4:2.5:0.5, v/v/v/v). C(4)D parameters were set at fixed amplitude of 100 V and frequency of 1000 kHz. The developed method was validated. Calibration curves of the ten FAs were well correlated (r(2)>0.99) within the range of 5-250 μg mL(-1) for lauric acid, and 3-250 μg mL(-1) for the other FAs. The method was simple and sensitive with detection limits (S/N=3) of 0.9-1.9 μg mL(-1) and good relative standard deviations of intra- and inter-day for migration times and peak areas (≤9.7%) were achieved. The method was applied to the determination of FAs in margarine samples. The proposed method offers distinct advantages over the GC and HPLC methods, especially in terms of simplicity (without derivatization) and sensitivity.
    Matched MeSH terms: Stearic Acids/analysis*; Stearic Acids/chemistry*
  6. Phytochemical analysis and antioxidant activity of the seed of Telfairia occidentalis Hook (Cucurbitaceae)
    Eseyin OA, Daniel A, Paul TS, Attih E, Emmanuel E, Ekarika J, et al.
    Nat Prod Res, 2018 Feb;32(4):444-447.
    PMID: 28361553 DOI: 10.1080/14786419.2017.1308366
    The 2,2-diphenyl-1-picryl hydrazyl (DPPH) radical, nitric oxide, reducing power, hydrogen peroxide scavenging, and total antioxidant activities of the methanol extract, n-hexane, dichloromethane, ethyl acetate, butanol and aqueous fractions of the seed of Telfairia occidentalis were evaluated. Total phenolic content was determined using the Folin-Ciocalteu method. The dichloromethane fraction exhibited the highest DPPH radical scavenging, reducing power and total antioxidant activities. Two pure compounds which were identified by FTIR, H-and 2D NMR and Mass spectroscopy as 9-octadecenoic acid (TOS B) and 10-hydroxyoctadecanoic acid (TOS C) and four oily isolates, TOS A, TOS D, TOS E and TOS F were obtained from the dichloromethane fraction. TOS E had the highest DPPH radical scavening activity comparable to that of ascorbic acid. GC-MS analysis revealed the major compounds in TOS E as 4-(2,2-Dimethyl-6-methylene cyclohexylidene)-2-butanol; 3-(3-hydroxybutyl)-2,4,4-trimethyl-2-cyclohexene-1-one and 1,2-Benzenedicarboxylic acid disooctyl ester. Thus, the seed of T. occidentalis can be consumed for its antioxidant property.
    Matched MeSH terms: Stearic Acids/analysis; Stearic Acids/chemistry
  7. Fulltext Recovery and Utilization of Palm Oil Mill Effluent Source as Value-Added Food Products
    Teh SS, Hock Ong AS, Mah SH
    J Oleo Sci, 2017;66(11):1183-1191.
    PMID: 29093377 DOI: 10.5650/jos.ess17078
    The environmental impacts of palm oil mill effluent (POME) have been a concern due to the water pollution and greenhouse gases emissions. Thus, this study was conducted to recover the value-added products from POME source before being discharged. The samples, before (X) and after (Y) the pre-recovery system in the clarification tank were sampled and analysed and proximate analysis indicated that both samples are energy rich source of food due to high contents of fats and carbohydrates. GCMS analysis showed that the oil extracts contain predominantly palmitic, oleic, linoleic and stearic acids. Regiospecific analysis of oil extracts by quantitative 13C-NMR spectroscopy demonstrated that both oil extracts contain similar degree of saturation of fatty acids at sn-2 and sn-1,3 positions. The samples are rich in various phytonutrients, pro-vitamin A, vitamin E, squalene and phytosterols, thus contributing to exceptionally high total flavonoid contents and moderate antioxidant activities. Overall, samples X and Y are good alternative food sources, besides reducing the environmental impact of POME.
    Matched MeSH terms: Stearic Acids/analysis; Stearic Acids/isolation & purification
  8. Fulltext Elucidation of in-vitro anti-inflammatory bioactive compounds isolated from Jatropha curcas L. plant root
    Othman AR, Abdullah N, Ahmad S, Ismail IS, Zakaria MP
    BMC Complement Altern Med, 2015;15:11.
    PMID: 25652309 DOI: 10.1186/s12906-015-0528-4
    BACKGROUND: The Jatropha curcas plant or locally known as "Pokok Jarak" has been widely used in traditional medical applications. This plant is used to treat various conditions such as arthritis, gout, jaundice, wound and inflammation. However, the nature of compounds involved has not been well documented. Hence, this study was conducted to investigate the anti-inflammatory activity of different parts of J. curcas plant and to identify the active compounds involved.
    METHODS: In this study, methanol (80%) extraction of four different parts (leaves, fruits, stem and root) of J. curcas plant was carried out. Phenolic content of each part was determined by using Folin-Ciocalteau reagent. Gallic acid was used as the phenol standard. Each plant part was screened for anti-inflammatory activity using cultured macrophage RAW 264.7 cells. The active plant part was then partitioned with hexane, chloroform, ethyl acetate and water. Each partition was again screened for anti-inflammatory activity. The active partition was then fractionated using an open column chromatography system. Single spots isolated from column chromatography were assayed for anti-inflammatory and cytotoxicity activities. Spots that showed activity were subjected to gas chromatography mass spectrophotometry (GC-MS) analysis for identification of active metabolites.
    RESULTS: The hexane partition from root extract showed the highest anti-inflammatory activity. However, it also showed high cytotoxicity towards RAW 264.7 cells at 1 mg/mL. Fractionation process using column chromatography showed five spots. Two spots labeled as H-4 and H-5 possessed anti-inflammatory activity, without cytotoxicity activity. Analysis of both spots by GC-MS showed the presence of hexadecanoic acid methyl ester, octadecanoic acid methyl ester and octadecanoic acid.
    CONCLUSION: This finding suggests that hexadecanoic acid methyl ester, octadecanoic acid methyl ester and octadecanoic acid could be responsible for the anti-inflammatory activity of the J. curcas root extract.
    Matched MeSH terms: Stearic Acids/analysis; Stearic Acids/pharmacology*; Stearic Acids/therapeutic use
  9. Lipid based biocompatible ionic liquids: synthesis, characterization and biocompatibility evaluation
    Uddin S, Chowdhury MR, Wakabayashi R, Kamiya N, Moniruzzaman M, Goto M
    Chem Commun (Camb), 2020 Oct 19.
    PMID: 33073787 DOI: 10.1039/d0cc04491a
    We report a new series of lipid-based biocompatible ionic liquids (LBILs) consisting of the long-chain phosphonium compound 1,2-dimyristoyl-sn-glycero-3-ethyl-phosphatidylcholine as the cation and the long-chain fatty acids stearic acid, oleic acid, or linoleic acid as anions. These materials were found to be completely miscible with many polar and nonpolar organic solvents as well as dispersible in water. These LBILs also exhibited excellent biocompatibility with an artificial three-dimensional human epidermis model.
    Matched MeSH terms: Stearic Acids
  10. Effect of mixing process parameters and suitability of backbone polymer for aluminum powder injection molding feedstock
    Abdullahi A, Choudhury I, Azuddin M, Nahar N
    Sains Malaysiana, 2017;46:477-483.
    A suitable and cost-effective microfabrication technique for processing aluminum micropart is required, as the choice
    of aluminum microparts for aerospace, electronics and automobile components is preferred over other metals due to its
    excellent properties. Meanwhile, powder injection molding (PIM) is identified as an economical manufacturing technique
    for processing ceramic and micro-metal powders into microparts and or components. Therefore, this study investigates
    formulation and processing of aluminum PIM feedstock using a custom-made machine. The investigation is focused on
    the effect of mixing process parameters (powder loading, rotor speed and mixing temperature) and the suitability of
    the backbone polymer. The formulated PIM feedstock constituents are paraffin wax (PW), stearic acid (SA), high-density
    polyethylene (HDPE)/ medium-density polyethylene (MDPE) alternatively and aluminum micro-metal powder. Taguchi
    method is used for the design of experiments (DOEs) and analysis. In addition, response surface methodology (RSM) is
    employed to develop empirical viscosity models. The optimum powder-binder mixing ratio of 58:42 vol. % with rotor
    speed of 43 rpm were determined for preparing aluminum PIM feedstock using mini-lab mixer developed. The empirical
    model developed for aluminum PIM feedstock viscosity shows a good fit with R2
    values of 0.84 using HDPE and 0.96 for
    MDPE binder system. This investigation demonstrates preparation and suitability of aluminum PIM feedstock using waxbased
    binder system.
    Matched MeSH terms: Stearic Acids
  11. Fulltext Effects of lubrication in warm powder compaction process
    Rahman, M.M., Nor, S.S.M., Rahman, H.Y.
    ASM Science Journal, 2011;5(1):11-18.
    MyJurnal
    Warm compaction is an advanced manufacturing technique which consists of two consecutive steps, i.e. powder compaction at above ambient temperature and sintering in a controlled environment. Due to the relative movement between the powder mass and die wall as well as sliding among powder particles, frictional force is generated during the compaction stage. Admixed lubricant is used during the compaction step in order to minimize friction and hence improve the uniformity of the density of distribution inside the component. However, during the sintering process, trapped lubricant is often found to be burnt out hence leaving pores or voids which result in the lower strength of the final products. Warm compaction was initiated in the nineties, however not much information has been published about the effects of lubrication on the quality of the components produced through this route. Therefore, this paper presents the outcome of an experimental investigation about the effects of lubrication on manufacturing near-net shape components through the warm compaction route. Iron powder ASC 100.29 was mixed mechanically with zinc stearate to prepare the feedstock. Mixing time, weight percentage of lubricant content and compaction temperature were varied during green compact generation while sintering temperature, heating rate and holding time were manipulated during sintering. The relative densities and strengths of the final products were investigated at every compaction as well as sintering parameter. The results revealed that lubrication could provide significant effects at the compaction temperature of 180ºC while no significant effect of lubrication was observed during sintering. The suitable lubricant content was found to be 0.4 wt% and mixing time was around 30 min and the sintering temperature was around 990ºC.
    Matched MeSH terms: Stearic Acids
  12. Fulltext Palm kernel oil blends as suppository bases in the delivery of aspirin
    Noordin, M.I., Chung, L.Y.
    JUMMEC, 2007;10(2):43-50.
    MyJurnal
    Rectal delivery of drugs has been proven to be effective in terms of drug absorption and distribution comparable with other routes such as oral, buccal, sublingual or even nasal. In this study, two new suppository bases were developed using combinations of locally sourced hydrogenated palm kernel oil, hydrogenated palm kernel stearin and hydrogenated palm kernel olein with mixtures of stearic acid and glyceryl monostearate. When formulated with aspirin, these bases produced suppositories with acceptable characteristics. These aspirin suppositories were tested on twelve healthy subjects after an approval from the Medical Ethics Committee, University of Malaya had been procured. We quantified aspirin from the urine samples of the subjects to determine the relative availability of the different suppository preparations relative to an oral dose. The excretion of salicylic acid, one of the metabolite of aspirin in human urine taking aspirin was quantified. The F value was found to range from 1.16 to 1.38. Hence, the excretion results showed that these palm kernel oil blends are suitable suppository bases.
    Matched MeSH terms: Stearic Acids
  13. Optimization of injection molding and solvent debinding parameters of stainless steel powder (SS316L) based feedstock for metal injection molding
    MUHAMMAD ILMAN HAKIMI CHUA, ABU BAKAR SULONG, MOHD FAZURI ABDULLAH, NORHAMIDI MUHAMAD
    Sains Malaysiana, 2013;42:1743-1750.
    In this study, injection molding parameters, including green strength, surface quality and green part density, were optimized using the L18 Taguchi orthogonal array. The L25 Taguchi method was used to optimize the green density of solvent debinding parameters. The feedstock consisted of stainless steel powder (SS316L), with powder loading fractions of 63, 63.5 and 64 v/o. The binder compositions used in the study were polyethelene glycol (PEG-73 wt. %), polymethyl methacrilate (PMMA-25 wt. %) and stearic acid (2 wt. %). The Taguchi method was used to optimize the injection parameters. The obtained optimum parameters were as follows: mold temperature of 65oC, injection temperature of 145oC, injection pressure of 650 bar, injection flow rate of 20 m3/s, holding time of 5 s and powder loading of 64% v/o. Analysis of variance results showed that mold temperature has the greatest influence in the production of good green part surface quality and that powder loading gave the best green part strength. Immersion time and temperature were used to optimize for solvent debinding parameters. By optimizing the solvent debinding parameters, an immersion temperature of 61oC and immersion time of 5 h produced the highest density which is the optimum value gain in this study.
    Matched MeSH terms: Stearic Acids
  14. Fulltext Improvement in the mechanical strength of compacted urea fertilizer tablets through die wall lubrication
    Intan Soraya Shamsudin, Mohd Shamsul Anuar, Ahmad Husni Mohd. Hanif, Yus Aniza Yusof, Suraya Mohd Tahir
    Pertanika Journal of Science & Technology, 2019;27(1):193-203.
    MyJurnal
    This research was conducted to investigate the compaction performance and mechanical
    strength of compacted urea fertilizer in unlubricated and lubricated die systems. The
    ground urea 46% N fertilizer was compacted in a 13 mm flat-face cylindrical die set in
    both unlubricated and lubricated die systems with vegetable fatty acids and magnesium
    stearate as lubricants at various compaction stresses to produce urea fertilizer tablets. In
    conclusion, a lubricated die system reduces the frictional effects during the production of
    urea fertilizer tablets and also produces a mechanically stronger urea fertilizer tablet than
    those produced in an unlubricated die system. In addition, the vegetable fatty acids and
    magnesium stearate lubricants are found to improve the compaction performance of urea
    fertilizer tablet as well as its mechanical strength.
    Matched MeSH terms: Stearic Acids
  15. Fulltext Development of a controlled release of salicylic acid loaded stearic acid-oleic acid nanoparticles in cream for topical delivery
    Woo JO, Misran M, Lee PF, Tan LP
    ScientificWorldJournal, 2014;2014:205703.
    PMID: 24578624 DOI: 10.1155/2014/205703
    Lipid nanoparticles are colloidal carrier systems that have extensively been investigated for controlled drug delivery, cosmetic and pharmaceutical applications. In this work, a cost effective stearic acid-oleic acid nanoparticles (SONs) with high loading of salicylic acid, was prepared by melt emulsification method combined with ultrasonication technique. The physicochemical properties, thermal analysis and encapsulation efficiency of SONs were studied. TEM micrographs revealed that incorporation of oleic acid induces the formation of elongated spherical particles. This observation is in agreement with particle size analysis which also showed that the mean particle size of SONs varied with the amount of OA in the mixture but with no effect on their zeta potential values. Differential scanning calorimetry analysis showed that the SONs prepared in this method have lower crystallinity as compared to pure stearic acid. Different amount of oleic acid incorporated gave different degree of perturbation to the crystalline matrix of SONs and hence resulted in lower degrees of crystallinity, thereby improving their encapsulation efficiencies. The optimized SON was further incorporated in cream and its in vitro release study showed a gradual release for 24 hours, denoting the incorporation of salicylic acid in solid matrix of SON and prolonging the in vitro release.
    Matched MeSH terms: Stearic Acids/chemistry*
  16. Lipase-catalyzed esterification of palm-based 9,10-dihydroxystearic acid and 1-octanol in hexane--a kinetic study
    Awang R, Basri M, Ahmad S, Salleh AB
    Biotechnol Lett, 2004 Jan;26(1):11-4.
    PMID: 15005144
    The esterification of palm-based 9,10-dihydroxystearic acid (DHSA) and 1-octanol in hexane as catalyzed by lipase from Rhizomucor meihei (Lipozyme IM) followed Michaelis-Menten kinetics. The esterification reaction follows a Ping-Pong, Bi-Bi mechanism. The maximum rate was estimated to be 1 micromol min(-1) mg(-1) catalyst in hexane at 50 degrees C, and the Michaelis-Menten constants for DHSA and 1-octanol were 1.3 M and 0.7 M, respectively.
    Matched MeSH terms: Stearic Acids/chemistry*
  17. Transgenic oil palm: production and projection
    Parveez GK, Masri MM, Zainal A, Majid NA, Yunus AM, Fadilah HH, et al.
    Biochem Soc Trans, 2000 Dec;28(6):969-72.
    PMID: 11171275
    Oil palm is an important economic crop for Malaysia. Genetic engineering could be applied to produce transgenic oil palms with high value-added fatty acids and novel products to ensure the sustainability of the palm oil industry. Establishment of a reliable transformation and regeneration system is essential for genetic engineering. Biolistic was initially chosen as the method for oil palm transformation as it has been the most successful method for monocotyledons to date. Optimization of physical and biological parameters, including testing of promoters and selective agents, was carried out as a prerequisite for stable transformation. This has resulted in the successful transfer of reporter genes into oil palm and the regeneration of transgenic oil palm, thus making it possible to improve the oil palm through genetic engineering. Besides application of the Biolistics method, studies on transformation mediated by Agrobacterium and utilization of the green fluorescent protein gene as a selectable marker gene have been initiated. Upon the development of a reliable transformation system, a number of useful targets are being projected for oil palm improvement. Among these targets are high-oleate and high-stearate oils, and the production of industrial feedstock such as biodegradable plastics. The efforts in oil palm genetic engineering are thus not targeted as commodity palm oil. Due to the long life cycle of the palm and the time taken to regenerate plants in tissue culture, it is envisaged that commercial planting of transgenic palms will not occur any earlier than the year 2020.
    Matched MeSH terms: Stearic Acids/analysis*
  18. Stability evaluation of quality parameters for palm oil products at low temperature storage
    Ramli NAS, Mohd Noor MA, Musa H, Ghazali R
    J Sci Food Agric, 2018 Jul;98(9):3351-3362.
    PMID: 29250790 DOI: 10.1002/jsfa.8839
    BACKGROUND: Palm oil is one of the major oils and fats produced and traded worldwide. The value of palm oil products is mainly influenced by their quality. According to ISO 17025:2005, accredited laboratories require a quality control procedure with respect to monitoring the validity of tests for determination of quality parameters. This includes the regular use of internal quality control using secondary reference materials. Unfortunately, palm oil reference materials are not currently available. To establish internal quality control samples, the stability of quality parameters needs to be evaluated.

    RESULTS: In the present study, the stability of quality parameters for palm oil products was examined over 10 months at low temperature storage (6 ± 2 °C). The palm oil products tested included crude palm oil (CPO); refined, bleached and deodorized (RBD) palm oil (RBDPO); RBD palm olein (RBDPOo); and RBD palm stearin (RBDPS). The quality parameters of the oils [i.e. moisture content, free fatty acid content (FFA), iodine value (IV), fatty acids composition (FAC) and slip melting point (SMP)] were determined prior to and throughout the storage period. The moisture, FFA, IV, FAC and SMP for palm oil products changed significantly (P stearic acid composition for CPO and linolenic acid composition for CPO, RBDPO, RBDPOo and RBDPS did not (P > 0.05). The stability study indicated that the quality of the palm oil products was stable within the specified limits throughout the storage period at low temperature.

    CONCLUSION: The storage conditions preserved the quality of palm oil products throughout the storage period. These findings qualify the use of the palm oil products CPO, RBDPO, RBDPOo and RBDPS as control samples in the validation of test results. © 2017 Society of Chemical Industry.

    Matched MeSH terms: Stearic Acids/analysis
  19. Fulltext Improvement of physicochemical characteristics of monoepoxide linoleic acid ring opening for biolubricant base oil
    Salimon J, Salih N, Abdullah BM
    J Biomed Biotechnol, 2011;2011:196565.
    PMID: 22131799 DOI: 10.1155/2011/196565
    For environmental reasons, a new class of environmentally acceptable and renewable biolubricant based on vegetable oils is available. In this study, oxirane ring opening reaction of monoepoxide linoleic acid (MEOA) was done by nucleophilic addition of oleic acid (OA) with using p-toluene sulfonic acid (PTSA) as a catalyst for synthesis of 9(12)-hydroxy-10(13)-oleoxy-12(9)-octadecanoic acid (HYOOA) and the physicochemical properties of the resulted HYOOA are reported to be used as biolubricant base oils. Optimum conditions of the experiment using D-optimal design to obtain high yield% of HYOOA and lowest OOC% were predicted at OA/MEOA ratio of 0.30 : 1 (w/w), PTSA/MEOA ratio of 0.50 : 1 (w/w), reaction temperature at 110°C, and reaction time at 4.5 h. The results showed that an increase in the chain length of the midchain ester resulted in the decrease of pour point (PP) -51°C, increase of viscosity index (VI) up to 153, and improvement in oxidative stability (OT) to 180.94°C.
    Matched MeSH terms: Stearic Acids/chemical synthesis*
  20. Preparation and characterization of dutasteride-loaded nanostructured lipid carriers coated with stearic acid-chitosan oligomer for topical delivery
    Noor NM, Sheikh K, Somavarapu S, Taylor KMG
    Eur J Pharm Biopharm, 2017 Aug;117:372-384.
    PMID: 28412472 DOI: 10.1016/j.ejpb.2017.04.012
    Dutasteride, used for treating benign prostate hyperplasia (BPH), promotes hair growth. To enhance delivery to the hair follicles and reduce systemic effects, in this study dutasteride has been formulated for topical application, in a nanostructured lipid carrier (NLC) coated with chitosan oligomer-stearic acid (CSO-SA). CSO-SA has been successfully synthesized, as confirmed using1H NMR and FTIR. Formulation of dutasteride-loaded nanostructured lipid carriers (DST-NLCs) was optimized using a 23full factorial design. This formulation was coated with different concentrations of stearic acid-chitosan solution. Coating DST-NLCs with 5% SA-CSO increased mean size from 187.6±7.0nm to 220.1±11.9nm, and modified surface charge, with zeta potentials being -18.3±0.9mV and +25.8±1.1mV for uncoated and coated DST-NLCs respectively. Transmission electron microscopy showed all formulations comprised approximately spherical particles. DST-NLCs, coated and uncoated with CSO-SA, exhibited particle size stability over 60days, when stored at 4-8°C. However, NLCs coated with CSO (without conjugation) showed aggregation when stored at 4-8°C after 30days. The measured particle size for all formulations stored at 25°C suggested aggregation, which was greatest for DST-NLCs coated with 10% CSO-SA and 5% CSO. All nanoparticle formulations exhibited rapid release in an in vitro release study, with uncoated NLCs exhibiting the fastest release rate. Using a Franz diffusion cell, no dutasteride permeated through pig ear skin after 48h, such that it was not detected in the receptor chamber for all samples. The amount of dutasteride in the skin was significantly different (p<0.05) for DST-NLCs (6.09±1.09μg/cm2) without coating and those coated with 5% CSO-SA (2.82±0.40μg/cm2), 10% CSO-SA (2.70±0.35μg/cm2) and CSO (2.11±0.64μg/cm2). There was a significant difference (p<0.05) in the cytotoxicity (IC50) between dutasteride alone and in the nanoparticles. DST-NLCs coated and uncoated with CSO-SA increased the maximum non-toxic concentration by 20-fold compared to dutasteride alone. These studies indicate that a stearic acid-chitosan conjugate was successfully prepared, and modified the surface charge of DST-NLCs from negative to positive. These stable, less cytotoxic, positively-charged dutasteride-loaded nanostructured lipid carriers, with stearic acid-chitosan oligomer conjugate, are appropriate for topical delivery and have potential for promotion of hair growth.
    Matched MeSH terms: Stearic Acids/administration & dosage; Stearic Acids/chemistry*
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links