Landfill leachate is one of the major contamination sources. In this study, the ability of synthetic ion exchange resins which carry different mobile ion for removing color, chemical oxygen demand (COD), and ammonia nitrogen (NH(3)-N) from stabilized leachate was investigated. The synthetic resin INDION 225 Na as a cationic exchanger and INDION FFIP MB as an anionic exchanger were used in this study. INDION 225 Na was used in hydrogen form (H(+)) and in sodium form (Na(+)), while INDION FFIP MB resin was used in hydroxide form (OH(-)) and in calcium form (Cl(-)) form. The results indicated better removal of color, COD and NH(3)-N by using INDION 225 Na in H(+) as compared with Na(+) form, while no performance differences were observed by using INDION FFIP MB in OH(-) or Cl(-) form. Applying cationic resin followed by anionic resin achieved 97, 88 and 94, percent removal of color, COD and NH(3)-N. The residual amounts were 160 Pt-Co, 290 mg/L and 110 mg/L of color, COD and NH(3)-N respectively.
This study investigates the potential of using small amounts of ionic liquids (IL) to enhance ultrasound-assisted extraction of lipids content from green microalgae. Three imidazolium-based ILs (butyl, octyl and dodecyl), each of them with two anions (bromide and acetate) were tested as additives. Viscosity and surface tension of the ILs aqueous mixtures were analyzed to determine the influence of ILs' anions and alkyl chain length, whereas KI dosimetry experiments were used as an indicator of radicals formation. A key finding suggests that the small addition of ILs improves the ultrasonication either by enhancing the viscosity and reducing the water surface tension, leading to a more powerful acoustic cavitation process or by increasing HO° production likely to oxidize the microalgae cells membranes, and consequently disrupting them on a more efficient manner. KI dosimetry also revealed that long ILs alkyl chain is detrimental. This experimental observation is confirmed thus strengthened as the yield of extracted lipids from green microalgae has shown an incremental trend when the IL concentration also increased. These hypotheses are currently under investigation to spot detailed impact of ILs on cavitation process.
In the present study, pectinase was produced by local fungal isolate, Aspergillus niger LFP-1 grown on pomelo peels as a sole carbon source under solid-state fermentation (SSF). The purification process begins with the concentration of crude enzyme using ammonium sulfate precipitation and followed by purification using anion-exchange column chromatography (DEAE-Sephadex) and subsequently using gel filtration column chromatography (Sephadex G-100). On the other hand, the molecular weight of the purified enzyme was determined through SDS-PAGE. The findings revealed the crude enzyme was purified up to 75.89 folds with a specific activity of 61.54 U/mg and the final yield obtained was 0.01%. The molecular mass of the purified pectinase was 48 kDa. The optimum pH and temperature were 3.5 and 50°C, respectively. This enzyme was stable at a range of pH 3.5 to 4.5 and a relatively high temperature (40°C-50°C) for 100 min. The Km and Vmax were found to be 3.89 mg/mL and 1701 U/mg, respectively. Meanwhile, pectin from citrus fruit and the metal ion (Co2+) were the best substrate and inducer to enhance pectinase yield, respectively.
The values of the relative counterion (X) binding constant R(X)(Br) (=K(X)/K(Br), where K(X) and K(Br) represent cetyltrimethylammonium bromide, CTABr, micellar binding constants of X(v-) (in non-spherical micelles), v = 1,2, and Br(-) (in spherical micelles)) are 58, 68, 127, and 125 for X(v-) = 1(-), 1(2-), 2(-), and 2(2-), respectively. The values of 15 mM CTABr/[Na(v)X] nanoparticles-catalyzed apparent second-order rate constants for piperidinolysis of ionized phenyl salicylate at 35 °C are 0.417, 0.488, 0.926, and 0.891 M(-1) s(-1) for Na(v)X = Na1, Na2 1, Na2, and Na2 2, respectively. Almost entire catalytic effect of nanoparticles catalyst is due to the ability of nonreactive counterions, X(v-), to expel reactive counterions, 3(-), from nanoparticles to the bulk water phase.
Chlorination is a common disinfection method in water treatment. This method can be converted into an advanced oxidation process by incorporating UV irradiation during water treatment. This study investigated the degradation of hydrochlorothiazide (HCTZ) by chlorination and UV/chlorination in water. HCTZ is a diuretic medication that has been frequently detected in wastewater. For chlorination, the second-order rate constant for the reaction between HCTZ with free available chlorine was found to increase with increasing pH from 5 to 8 due to the increase of the anionic HCTZ fraction. UV/chlorination was found to be more efficient in removing HCTZ as compared with chlorination due to the presence of reactive radical species such as hydroxyl radicals. For transformation by-products, chlorination was found to produce two by-products via chlorination and hydroxylation reactions that occurred at the aromatic ring of HCTZ. For UV/chlorination, an additional by-product formed through a radical reaction at the heterocyclic moiety of HCTZ was detected. Based on the Escherichia coli inhibition study, chlorination and UV/chlorination were found to increase the toxicity of the HCTZ solution. This result indicated that even UV/chlorination showed higher effectiveness in removing HCTZ; however, it also has the potential to generate toxic by-products and effluent.
This paper describes the preparation of and experimentation undertaken by heterogeneous chitosan membrane as ion selective electrode for glutamate ion. The linearity response was obtained in the range of 1.0x10(-5) to 1.0x10(-1)M with a detection limit of 1.0x10(-6)M. The performance of the electrode was found in the pH range of 4.0-8.0 at temperature 25+/-3 degrees C. The response time was at 5-35s and was useful for a period of more than 4 months. The selectivity values towards some anions indicates good selectivity over a number of interfering anions. No significant improvement of membrane performance over additional of plasticizers such as 2-NPOE, BEHA and DOPP. The electrodes gave sufficient Nernstian responses with the exception of membrane with 2-NPOE.
A new lead(II) electrode has been constructed with poly(hydroxamic acid) (PHXA) as the active material and silicone rubber as the supporting material. The electrode gave near Nerstian response over the concentration range 4 x 10(-5)-1 x 10(-2)M lead(II). The detection limit of the electrode is approximately 4 x 10(-6)M and the electrode works well in the pH range 4.5-6.0. The response time was 50-120 sec over the whole concentration range and the electrode has a working life of at least 4 weeks. Iron(III) severely poisoned the electrode membrane. Nickel(II) and mercury(II) gave very strong interference compared to copper(II), silver(I), cobalt(II), sodium(I), potassium(I), zinc(II) and cadmium(II) which gave some or little interference. Values determined with atomic absorption (AAS) and a commercial lead(II) electrode were in good agreement with those measured with the lead(II) electrode reported here.
(1)H NMR evidence for direct coordination between the Ln(III) ion and the oxygen atoms of the pentaethylene glycol (EO5) ligand and the picrate anion (Pic) in [Ln(Pic)(2)(EO5)][Pic] {Ln=Ce and Nd} complexes are confirmed by single X-ray diffraction. No dissociation of Ln-O bonds in dimethyl sulfoxide-d solution was observed in NMR studies conducted at different temperatures ranging 25-100 degrees C. The Ln(III) ion was chelated to nine oxygen atoms from the EO5 ligand in a hexadentate manner and the two Pic anions in each bidentate and monodentate modes. Both compounds are isostructural and crystallized in monoclinic with space group P2(1)/c. Coordination environment around the Ce1 and Nd1 atoms can be described as tricapped trigonal prismatic and monocapped square antiprismatic geometries, respectively. The crystal packing of the complexes have stabilized by one dimensional (1D) chains along the [001] direction to form intermolecular O-Hcdots, three dots, centeredO and C-Hcdots, three dots, centeredO hydrogen bonding. The molar conductance of the complexes in DMSO solution indicated that both compounds are ionic. The complexes had a good thermal stability. Under the UV-excitation, these complexes exhibited the red-shift emission.
Local heterogeneity in lipid self-assembly is important for executing the cellular membrane functions. In this work, we chemically modified 2-(2'-hydroxyphenyl)benzoxazole (HBO) and attached a C8 alkyl chain in two different locations to probe the microscopic environment of four lipidic phases of dodecyl β-maltoside. The fluorescence change in HBO and the new probes (HBO-1 and HBO-2) shows that in all phases (micellar, hexagonal, cubic and lamellar) three HBO tautomeric species (solvated syn-enol, anionic, and closed syn-keto) are stable. The formation of multi tautomers reflects the heterogeneity of the lipidic phases. The results indicate that HBO and HBO-1 reside in a similar location within the head group region, whereas HBO-2 is slightly pushed away from the sugar-dominated area. The stability of the solvated syn-enol tautomer is due to the formation of a hydrogen bond between the OH group of the HBO moiety and an adjacent oxygen atom of a sugar unit. The detected HBO anions was proposed to be a consequence of this solvation effect where a hydrogen ion abstraction by the sugar units is enhanced. Our results point to a degree of local heterogeneity and ionization ability in the head group region as a consequence of the sugar amphoterism.
Anion passivation effect on metal-oxide nano-architecture offers a highly controllable platform for improving charge selectivity and extraction, with direct relevance to their implementation in hybrid solar cells. In current work, we demonstrated the incorporation of fluorine (F) as an anion dopant to address the defect-rich nature of ZnO nanorods (ZNR) and improve the feasibility of its role as electron acceptor. The detailed morphology evolution and defect engineering on ZNR were studied as a function of F-doping concentration (x). Specifically, the rod-shaped arrays of ZnO were transformed into taper-shaped arrays at high x. A hypsochromic shift was observed in optical energy band gap due to the Burstein-Moss effect. A substantial suppression on intrinsic defects in ZnO lattice directly epitomized the novel role of fluorine as an oxygen defect quencher. The results show that 10-FZNR/P3HT device exhibited two-fold higher power conversion efficiency than the pristine ZNR/P3HT device, primarily due to the reduced Schottky defects and charge transfer barrier. Essentially, the reported findings yielded insights on the functions of fluorine on (i) surface -OH passivation, (ii) oxygen vacancies (Vo) occupation and (iii) lattice oxygen substitution, thereby enhancing the photo-physical processes, carrier mobility and concentration of FZNR based device.
Solid polymer electrolytes electrolytes based Poly
(ethylene oxide) (PEO) complexed with sodium
trifluoromethanesulfonate (NaCF3SO3
) salt were prepared by
using solution cast technique. Ion-polymer ionic conductivity
and interaction studies have been reported by Electrical
Impedance spectroscopy (EIS) and Fourier transform infrared
spectroscopy (FTIR). FTIR studies suggested that there are
stronger interaction between Na+
ions and the polymer than
interaction of anions cations of the salt. The temperature
dependance electrical conductivity of polymer electrolytes films
follow Arrhenius relation and the low activation energy 0.2993
eV was observed for PEO-18 wt. % NaCF3SO3 below 323 K.
In this study, a symmetric supercapacitor has been fabricated by adopting the nanostructured iron oxide (Fe304)-activated carbon (Ac) composite as the core electrode materials. The composite electrodes were prepared via a facile mechanical mixing process and PTFE polymeric solution has been used as the electrode material binder. Structural analysis of the nanocomposite electrodes were characterized by scanning electron microscopy ( sEm) and Brunauer-Emmett-Teller (BET) analysis. The electrochemical performances of the prepared supercapacitor were studied using cyclic voltammetry (cv) and electrochemical impedance spectroscopy (Eis) in 1.0 M Na2S03 and 1.0 M Na2SO4 aqueous solutions, respectively. The experimental results showed that the highest specific capacitance of 43 FIg is achieved with a fairly low Fe304 nanomaterials loading (4 wt. %) in 1 M Na2S03. It is clear that the low concentration of nanostructured Fe304 has improved the capacitive performance of the composite via pseudocapacitance charge storage mechanism as well as the enhancement on the specific surface areas of the electrode. However, further increasing of the Fe304 content in the electrode is found to distort the capacitive performance and deteriorate the specific surface area of the electrode, mainly due to the aggregation of the Fe304 particles within the composite. Additionally, the cv results showed that the Fe3041Ac nanocomposite electrode in Na2S03 electrolyte exhibits a better charge storage performance if compared with Na2SO4 solution. It is believed that Fe304 nanoparticles can provide favourable surface adsorption sites for sulphite (S032-) anions which act as catalysts for subsequent redox and intercalation reactions.
Kajian ini dijalankan bagi mengenalpasti kepelbagaian nisbah 234U/238U yang wujud di dalam jumlah pepejal terampai (TSS) pada lapan stesen yang berbeza di Kuala Selangor, Selangor. Prosedur kajian ini melibatkan proses persampelan, pemendakan, resin penukaran anion, pemendakan elektrik dan teknik pengiraaan spektrometer alfa. Nisbah 234U/238U adalah paling tinggi di Stesen 8 (234U/238U = 2.98) dan Stesen 2 (234U/238U = 3.34) pada persampelan pertama. Manakala pada persampelan kedua julat nisbah 234U/238U adalah lebih luas iaitu antara 1.29 (Stesen 4) hingga 11.57 (Stesen 6). Ini disebabkan oleh berlakunya pergerakan 234U bersama-sama mikroorganisme di dalam fasa terampai dan berlaku proses penurunan U(VI) kepada U(IV) yang akan memendakkan uranium daripada air ke dalam sedimen.
Organotin compounds especially the dialkyltin derivatives are reported to possess anti-tumour properties. The diorganotin(IV) complexes of the type Me2SnL1, Me2SnL2, Bu2SnL1, Bu2SnL2 and Ph2SnL1 (L1 and L2 is the anion of the thiosemicarbazone ligand formed by the condensation reaction of 2,3-dihydroxybenzaldehyde with thiosemicarbazide or its N(4)-methyl substituent) were synthesized using 1:1 metal-to-ligand reactant ratios. The newly synthesized complexes were characterized using elemental analysis, infrared and nuclear magnetic resonance (1H, 13C, 119Sn) spectroscopic techniques. Complex formation between the organotin(IV) moiety and the anions of 2,3-dihydroxybenzaldehyde thiosemicarbazone and 2,3-dihydroxybenzaldehyde 4-methylthiosemicarbazone occurred with chelation at the o-dihydroxy positions. The complexes are proposed to have tetrahedral geometry.
Catanionic system using anionic sodium bis-(2ethylhexyl)sulfosuccinate (Am) and cationic cetyltrimethylammonium bromide (cTAB) is studied. The system is prepared by addition of CTAB solution to a prepared AOT solution until slight anionic-rich catanionic phase is produced. Catanionic system consists of the mixture of different types of surfactants and counterion due to electrostatic interaction between the oppositely charged surfactant. Both of these products affect the in surface activity of the surfactant. Hydrodynamic diameters decrease and clearer solution were seen with the increase of CTAB concentration in solution mixture. As a result, mixed surfactant with larger hydrophobic region and the presence of counterion will induce smaller vesicle to form in catanionic system.
Surfactants in the atmosphere may act as cloud condensation nuclei, with a potentially negative impact on the global climate. Therefore, accurate determination of surfactants is crucial in order to investigate the possible effects of surfactants on the atmosphere. The aim of this study was to identify the optimum sampling method for measuring the maximum quantity of surfactants present in ambient air. Air samples were collected using a range of air sampling pumps that were made to vary in terms of flow rate, storage period, type of absorbing solution and the characteristics of the impinger tube. Samples obtained were analysed by colourimetry for anionic and cationic surfactants as methylene blue-active substances (MBAS) and disulphine blue-active substances (DBAS), respectively. Absorbance was measured at 650 nm for MBAS and 628 nm for DBAS using UV-visible spectrophotometer. We found that the optimum sampling method consisted of an absorbent solution (deionised water, buffer solution and methylene blue/disulphine blue solution) with the flow rate of 1.0 L/min. The concentration of surfactants in all sampling methods remained constant regardless of the storage period (1 day and 4 days), indicating that surfactants in the absorbing solution are quite stable. Covering the impinger tube was shown to influence the amount of both anionic and cationic surfactants detected.
Conocarpus fiber is an abundantly available and sustainable cellulosic biomass. With its richness in cellulose content, it is potentially used for manufacturing microcrystalline cellulose (MCC), a cellulose derivative product with versatile industrial applications. In this work, different samples of bleached fiber (CPBLH), alkali-treated fiber (CPAKL), and acid-treated fiber (CPMCC) were produced from Conocarpus through integrated chemical process of bleaching, alkaline cooking, and acid hydrolysis, respectively. Characterizations of samples were carried out with Scanning Electron Microscope (SEM), Energy Dispersive X-ray (EDX), Fourier Transform Infrared-Ray (FTIR), X-ray Diffraction (XRD), Thermogravimetric (TGA), and Differential Scanning Calorimetry (DSC). From morphology study, the bundle fiber feature of CPBLH disintegrated into micro-size fibrils of CPMCC, showing the amorphous compounds were substantially removed through chemical depolymerization. Meanwhile, the elemental analysis also proved that the traces of impurities such as cations and anions were successfully eliminated from CPMCC. The CPMCC also gave a considerably high yield of 27%, which endowed it with great sustainability in acting as alternative biomass for MCC production. Physicochemical analysis revealed the existence of crystalline cellulose domain in CPMCC had contributed it 75.7% crystallinity. In thermal analysis, CPMCC had stable decomposition behavior comparing to CPBLH and CPAKL fibers. Therefore, Conocarpus fiber could be a promising candidate for extracting MCC with excellent properties in the future.
Carboxymethylcellulose (CMC) is a water-soluble polymer, which is widely used in various
fields such as food additives, textiles, pharmaceuticals and cosmetics. In this study, hydrogel
was prepared from CMC by using calcium chloride as a crosslinking agent. Optimization
of the reaction was done through investigation of four different parameters which had
different percentage of CMC (w/v), percentage of calcium chloride (w/v), reaction time and
temperature. The gel content and swelling properties of the CMC hydrogel were studied.
The highest gel content was 85.33% at 7% of CMC (w/v) with 2% of calcium chloride (w/v)
in 24 hours reaction time at room temperature. The gel content increased with the increasing
concentration of CMC and CaCl2. This was due to the higher number of functional groups
of COO- that were available in more concentrated CMC which could crosslink with CaCl2
to give higher gel content. Increasing the percentage of CaCl2 will increase the electrostatic
attraction between anionic charges of polymer chains and multivalent cation (Ca2+) that
leads to increase in ionic crosslinking of CMC. The swelling properties of CMC hydrogel
showed that the optimum degree of swelling was 45.33 (g/g). The swelling capacity of the
hydrogel in water decreased with the increase of the gel content of CMC hydrogel. This
could be due to the increase in the degree of crosslinking of the CMC hydrogel.
Ibuprofen (Ibf) is a biologically active drug (BADs) and an emerging contaminant of concern (CECs) in aqueous streams. Due to its adverse effects upon aquatic organisms and humans, the removal and recovery of Ibf are essential. Usually, conventional solvents are employed for the separation and recovery of ibuprofen. Due to environmental limitations, alternative green extracting agents need to be explored. Ionic liquids (ILs), emerging and greener alternatives, can also serve this purpose. It is essential to explore ILs that are effective for recovering ibuprofen, among millions of ILs. The conductor-like screening model for real solvents (COSMO-RS) is an efficient tool that can be used to screen ILs specifically for ibuprofen extraction. The main objective of this work was to identify the best IL for the extraction of ibuprofen. A total of 152 different cation-anion combinations consisting of eight aromatic and non-aromatic cations and nineteen anions were screened. The evaluation was based upon activity coefficients, capacity, and selectivity values. Furthermore, the effect of alkyl chain length was studied. The results suggest that quaternary ammonium (cation) and sulfate (anion) have better extraction ability for ibuprofen than the other combinations tested. An ionic liquid-based green emulsion liquid membrane (ILGELM) was developed using the selected ionic liquid as the extractant, sunflower oil as the diluent, Span 80 as the surfactant, and NaOH as the stripping agent. Experimental verification was carried out using the ILGELM. The experimental results indicated that the predicted COSMO-RS and the experimental results were in good agreement. The proposed IL-based GELM is highly effective for the removal and recovery of ibuprofen.