The paper looks into the possibility of using standard addition method to analyse uranium and thorium in tin slag. Tin slag samples obtained from Butterworth was grind to 180 ȝm and injected with different concentrations of uranium and thorium. Linear calibration graphs were obtained for both these samples with R 2 values for uranium and thorium as 0.9989 and 0.9915 respectively. Based on this graphs, the initial uranium and thorium in the tin slag sample was established as 60 ppm for uranium and 160 ppm for thorium.
The long term objective of this research is to look into the possibility of replacing soil strength parameters such as cohesion and angle of friction with electrical resistivity value for the purpose of computing among others, factor of safety in slopes or bearing capacity of soil. This paper however is limited to the investigation of correlation between electrical resistivity with some selected soil parameters. Electrical resistivity tests, using a basic multi meter, steel moulds and other related equipment, were conducted in the laboratory on soil samples with variations in soil type, compaction energy and moisture content. The samples consisted of predominantly clay, silt and sandy size particles and were compacted in a 100 x 100 mm square mould, while the corresponding electrical resistivity tests were carried out using the disc electrode method in accordance to BS 1377. The values of the electrical parameters such as voltage, current and resistance, with the corresponding value of soil parameters such as cohesion, angle of friction and moisture content, were measured and recorded. The results of the tests produced some initial crude relationships between electrical resistivity and the selected soil parameters. The strongest correlation between electrical resistivity and angle of internal friction, φ, was obtained from the clay size samples with R2 of 0.824, while the maximum correlation between electrical resistivity and moisture content again was obtained through the clay samples with R2 of 0.818. From the other results and graphs analyzed, some consistencies and specific trends of behaviour observed gave some early indications that a more detail and precise correlation between electrical resistivity and soil strength parameters could be very well possible in future.
This paper describes a study on the design, fabrication and testing of a prototype digging device for sweet potato tubers in bris soil. The soil texture was sandy soil (fine sand 94.53%), with mean moisture content of 9.16% and mean bulk density of 1.44 g-cm-3. The soil was prepared in a soil bin. Three types of soil digging tools were designed and fabricated to determine the optimum draft force. These were Flat or plane, V-shaped and Hoe type blades. Plane and V-shaped blades were 30 cm long, and 13 cm wide, while the Hoe type had three rods, 25 mm in diameter, 30 cm long and 6.5 cm wide with sharp cutting edge. The digging tools were tested in a soil bin filled with bris soil to determine the optimum draft force and area of soil disturbance. The results were analysed using statistical analysis of variance (ANOVA). Comparison between all blade types and blade depths to measured draft force and the area of soil disturbed showed that the highest draft of 0.54 kN-m-2 was caused by a flat or plane blade at the optimum depth of 20 cm when the area of soil disturbed was 0.180 m2 . The V-shaped blade had the mean draft of 0.51 kN-m-2, with area of soil disturbance of 0.185 m2 . Thebest choice was V-shaped blade with a rake angle of 30o at 20 cm. depth. The selected blade was fixed onto the sweet potato harvester and tested on bris soil planted with sweet potato of Telong and VitAto varieties. The harvesting efficiency of the machine in bris soil was 93.64% and 90.49% for Telong (Plot A) and VitAto (Plot B) varieties, respectively. The average ground speed and turning time during operation for plots A and B was 0.56 km-hr-1 and 102.7 s and 0.99 km-hr-1 and 81.22 s, respectively. The harvesting efficiencies for both plots showed no significant difference. The total productive time (harvesting time) and unproductive time (turning time) in plot A, at a tractor speed of 0.56 km.hr-1, was 14.8 hours for harvesting a hectare of sweet potato ( 0.068 ha.hr-1). In plot B, the total time for harvesting a hectare of sweet potato was 8.35 hours (0.12 ha.hr-1) at a tractor speed of 0.99 km.hr-1. The average harvesting time for both plots was 11.47 hr.ha-1. The average field work rate was 0.087 ha.hr-1 or 34 man-hr.ha-1 compared to manual harvesting of 150 man-hrs.ha-1.
The aim of this study is to investigate the effects of Palm Oil Clinker (POC) added as a stabilizer for improving the strength of peat. Cement and POC are added into peat up to 50% of the maximum dry unit weight. Treated peat achieved higher dry unit weight, almost 2.5 times as compared to untreated peat. Unconfined compressive strength (UCS) of treated peat is also investigated for soaked and unsoaked conditions. The results show that curing time improved the unconfined compressive strength of treated sample and increased by a factor of 20 and 11 for unsoaked and soaked conditions after 28 days of curing, respectively. The treated samples added with POC can be related to an increase in unconfined compressive strength for long time curing.
The draft genome here presents the sequence of Bacillus subtilis UMX-103. The bacterial strain was isolated from hydrocarbon-contaminated soil from Terengganu, Malaysia. The whole genome of the bacterium was sequenced using Illumina HiSeq 2000 sequencing platform. The genome was assembled using de novo approach. The genome size of UMX-103 is 4,234,627 bp with 4399 genes comprising 4301 protein-coding genes and 98 RNA genes. The analysis of assembled genes revealed the presence of 25 genes involved in biosurfactant production, where 14 of the genes are related to biosynthesis and 11 of the genes are in the regulation of biosurfactant productions. This draft genome will provide insights into the genetic bases of its biosurfactant-producing capabilities.
The current work aimed to study the physical, chemical and biological properties of food wastes generated from small and medium industries by using Takakura composting methods. Composting method was referred as indigenous compost (IC) and commercial compost (CC) reactors. The reactors were operated at 44 °C, pH (6 to 8.5) and 40 to 55 % of moisture for 22 weeks in closed environment using a carpet around the basket to avoid external disturbance. The results revealed that the total Kjeldahl nitrogen (TKN), total phosphorus (TP) and potassium (K) in the IC reactors were 6300, 10.57 and 726.07 ppm, respectively, while 8400, 15.45 and 727.81 ppm, respectively, in the CC reactors. Moreover, both IC and CC has Cd2+, Cr2+, Cu2+, Pb2+, Ni2+ and Zn2+ concentrations within the compost legislation standard (CLS). The findings of this study indicated that the composting method could be used as an alternative food waste management in small and medium industry and the Takakura composting method is suitable for food waste composting.
Population increase and the demand for infrastructure development such as construction of highways and road widening are intangible, leading up to mass land clearing. As flat terrains become scarce, infrastructure expansions have moved on to hilly terrains, cutting through slopes and forests. Unvegetated or bare slopes are prone to erosion due to the lack of or insufficient surface cover. The combination of exposed slope, uncontrolled slope management practices, poor slope planning and high rainfall as in Malaysia could steer towards slope failures which then results in landslides under acute situation. Moreover, due to the tropical weather, the soils undergo intense chemical weathering and leaching that elevates soil erosion and surface runoff. Mitigation measures are vital to address slope failures as they lead to economic loss and loss of lives. Since there is minimal or limited information and investigations on slope stabilization methods in Malaysia, this review deciphers into the current slope management practices such as geotextiles, brush layering, live poles, rock buttress and concrete structures. However, these methods have their drawbacks. Thus, as a way forward, we highlight the potential application of soil bioengineering methods especially on the use of whole plants. Here, we discuss the general attributions of a plant in slope stabilization including its mechanical, hydrological and hydraulic effects. Subsequently, we focus on species selection, and engineering properties of vegetation especially rooting structures and architecture. Finally, the review will dissect and assess the ecological principles for vegetation establishment with an emphasis on adopting the mix-culture approach as a slope failure mitigation measure. Nevertheless, the use of soil bioengineering is limited to low to moderate risk slopes only, while in high-risk slopes, the use of traditional engineering measure is deemed more appropriate and remain to be the solution for slope stabilization.
A large amount of ammonia volatilization from the agricultural system causes environmental problems and increases production costs. Conservation agriculture has emerged as an alternate and sustainable crop production system. Therefore, in the present study, ammonia losses from different agricultural practices were evaluated for the wheat crop under different tillage practices. The results of the present study showed that the cumulative emission of ammonia flux from the wheat field varied from 6.23 to 24.00 kg ha-1 (P ≤ 0.05) in conservation tillage (CA) and 7.03 to 26.58 kg ha-1 (P ≤ 0.05) in conventional tillage (CT) among different treatments. Application of basal 80% nitrogen resulted in the highest ammonia flux in conventional and conservation tillage practices. The ammonia volatilization followed the following trend: urea super granules with band placement > neem-coated urea with band placement > neem-coated urea with broadcast before irrigation > neem-coated urea with broadcast after irrigation > slow-release N fertilizer (urea stabilized with DCD and N(n-butyl)thiophosphoric triamide) with band placement. The conservation agricultural practices involving conservation tillage appear to be a sustainable approach for minimizing ammonia volatilization and improving wheat productivity.
This study aimed at determining the effects of propagation medium and cutting types on the early growth performance of fig (Ficus carica L.) root and shoot. The experiment was conducted at the Glasshouse and Nursery Complex (GNC), International Islamic University Malaysia (IIUM). The split-plot design was employed with the main plot (propagation medium) and sub-plot (types of cutting). The propagation medium were sand:topsoil (1:3) (M1), topsoil:peat:sawdust (1:1:1) (M2) and peat:perlite (1:1) (M3). Two types of cutting were semi-hardwood (C1) and hardwood (C2). As a result, there were a significant effect of propagation medium on measured parameters. This study revealed that the most effective propagation medium and cutting types for the propagation of fig were a combination of peat and perlite at 1:1 ratio (M3) and hardwood cutting (C2), respectively as evidenced by significantly higher root and shoot growth quality as compared to other treatments.
Contaminated groundwater is a priority issue on the environmental agendas of developed countries. Therefore, there is an obvious need to develop instruments and decision-making mechanisms that allow the estimation of the risk to human health due to the presence of contaminants in soils and groundwater, in a fast and reliable manner. Thus, this study aims to assess whether the spilling of hydraulic fracturing fluids prior to injection has a potential risk to groundwater quality in the Kern County Sub-basin, California, by identifying the hydrological factors and solute transport characteristics that control these risks while taking into consideration the temperature rises due to climate change. The approach uses the concept of the groundwater pollution risk based on comparing the concentration of pollutants within the water table by using a predetermined permissible level. The current average annual temperature and that by the end of the 21st century was used to estimate the diffusion of benzene through three types of soil by using HYDRUS-1D software. The software was used to predict the contaminant concentration profile of benzene in the water table with special reference to the impact of surface temperatures. The results showed that an expected rise of the surface temperature by 4.3 °C led to an increase in the concentration of benzene by 2.3 μg/l in sandy loam soil, 6.8 μg/l in silt loam soil, and finally, 2.6 μg/l in loam soil. The results show that climate change can substantially affect soil properties and their chemical constituents, which then play a major role in absorbing pollutants.
Deforestation leads to the deterioration of soil fertility which occurs rapidly under tropical climates. Forest rehabilitation is one of the approaches to restore soil fertility and increase the productivity of degraded areas. The objective of this study was to evaluate and compare soil biological properties under enrichment planting and secondary forests at Tapah Hill Forest Reserve, Perak after 42 years of planting. Both areas were excessively logged in the 1950s and left idle without any appropriate forest management until 1968 when rehabilitation program was initiated. Six subplots (20 m × 20 m) were established within each enrichment planting (F1) and secondary forest (F2) plots, after which soil was sampled at depths of 0-15 cm (topsoil) and 15-30 cm (subsoil). Results showed that total mean microbial enzymatic activity, as well as biomass C and N content, was significantly higher in F1 compared to F2. The results, despite sample variability, suggest that the rehabilitation program improves the soil biological activities where high rate of soil organic matter, organic C, N, suitable soil acidity range, and abundance of forest litter is believed to be the predisposing factor promoting higher population of microbial in F1 as compared to F2. In conclusion total microbial enzymatic activity, biomass C and biomass N evaluation were higher in enrichment planting plot compared to secondary forest. After 42 years of planting, rehabilitation or enrichment planting helps to restore the productivity of planted forest in terms of biological parameters.
This paper aims to provide a review of the analytical extraction techniques for polycyclic aromatic hydrocarbons (PAHs) in soils. The extraction technologies described here include Soxhlet extraction, ultrasonic and mechanical agitation, accelerated solvent extraction, supercritical and subcritical fluid extraction, microwave-assisted extraction, solid phase extraction and microextraction, thermal desorption and flash pyrolysis, as well as fluidised-bed extraction. The influencing factors in the extraction of PAHs from soil such as temperature, type of solvent, soil moisture, and other soil characteristics are also discussed. The paper concludes with a review of the models used to describe the kinetics of PAH desorption from soils during solvent extraction.
Soil serves as a major reservoir for contaminants as it posseses an ability to bind various chemicals together. To safeguard the members of the public from an unwanted exposure, studies were conducted on the sediments and soil from water bodies that form the major sources of domestic water supply in northern peninsular Malaysia for their trace element concentration levels. Neutron Activation Analysis, using Nigeria Research Reactor-1 (NIRR-1) located at the Centre for Energy Research and Training, Zaria, Nigeria was employed as the analytical tool. The elements identified in major quantities include Na, K, and Fe while As, Br, Cr, U, Th, Eu, Cs, Co, La, Sm, Yb, Sc, Zn, Rb, Ba, Lu, Hf, Ta, and Sb were also identified in trace quantities. Gamma spectroscopy was also employed to analyze some soil samples from the same area. The results indicated safe levels in terms of the radium equivalent activity, external hazard index as well as the mean external exposure dose rates from the soil. The overall screening of the domestic water sources with relatively high heavy metals concentration values in sediments and high activity concentration values in soil is strongly recommended as their accumulation overtime as a consequence of leaching into the water may be of health concern to the members of the public.
We reviewed the epidemiology of STH in Malaysia from the 1970s to 2009. High prevalence rates persist among the rural Aborigines, estate workers and in urban slums and squatter areas. Trichuris trichiura is the most prevalent helminth in Malaysia ranging from 2.1% to 98.2%. Ascaris lumbricoides follows closely with a prevalence rate of 4.6-86.7%, while hookworm is the least prevalent (0-37.0%). A countrywide control program with special emphasis on school-based intervention is highly recommended among aboriginal people.
Experiments were carried out in the laboratory and greenhouse to determine the growth inhibitory effects of Grassohopper's cyperus (Cyperus iria L.) on the seedlings of 5 Malaysian rice varieties namely MR211, MRQ74, MR220, MR84 and MR232. Three concentrations of the aqueous extract of the weed (12.5, 25.0 and 50.0 g/l) and weed debris (5, 10 and 20 g dry debris/1000 g soil) were used to test the allelopathic effect of C. iria on the growth of the rice plants. The weed leaf, stem and root extracts reduced the growth of the rice seedlings and showed selective activity in the varieties. The C. iria leaf and stem extracts showed comparatively higher growth inhibitory effects than those from the root. The weed extract caused more reduction in the root length of the rice plant compared to the shoot length. Among the rice varieties tested, MR232 was found to be more susceptible to the weed inhibitory effect. The leaf extract of C. iria at full strength caused root and shoot reduction of MR232 by 88.1% and 73.1% respectively (compared to the control). In most cases the fresh weight of the rice seedlings were more affected than the plant height. Weed debris caused significant reduction of leaf chlorophyll content in all the rice varieties tested with the exception of MR211. The chlorophyll content of MR232 was greatly affected by the weed debris which caused reduction of 36.4% compared to the control. The inhibitory effects of weed extracts and debris on rice growth parameters were found to be concentration dependent.
Acid sulfate soil characterized by pyrite (FeS2) which produces high acidity (soil pH < 3.5) and release high amount of Al3+ and Fe2+. Application of 4 t ha-1 Ground Magnesium Limestone (GML), is a common rate used for acid sulfate soil by the rice farmers in Malaysia. Therefore, this study was conducted to evaluate the integral effect of ground magnesium limestone (GML) and calcium silicate and to determine the optimal combination on acid sulfate soils in Malaysia. The acid sulfate soils were incubated under the submerged condition for 120 days with GML (0, 2, 4, 6 t ha-1) in combination with calcium silicate (0, 1, 2, 3 t ha-1) arranged in a Completely Randomized Design (CRD). The soil was sampled after 30, 60, 90 and 120 days of incubation and analyzed for soil pH, exchangeable Al, Ca, Mg, K and available Si. A total of 2 out of 16 combinations met the desired soil requirement for rice cultivation. The desired chemical soil characteristics for rice cultivation are soil pH > 4, exchangeable Al < 2 cmolc Kg-1, exchangeable Ca > 2 cmolc kg-1, exchangeable Mg > 1 cmolc kg-1 and Si content > 43 mg kg-1. The combinations are i) 2 t ha-1 calcium silicate + 2 t ha-1 GML, and ii) 3 t ha-1 calcium silicate + 2 t ha-1 GML, respectively. These combination rates met the desired requirement of soil chemical characteristics for rice cultivation. Soil acidity was reduced by a gradual release of Ca2+ and SiO32- from calcium silicate continuously filling the exchange sites and reducing the potential of extra (free) H+ availability in the soil system. Combination of calcium silicate and GML, shows the ameliorative effect with; i) release of Ca, ii) binding of Al3+ making it inert Al-hydroxides and, iii) bind H+ to produce water molecules.
Food security and sustainable development of agriculture has been a key challenge for decades. To support this, nanotechnology in the agricultural sectors increases productivity and food security, while leaving complex environmental negative impacts including pollution of the human food chains by nanoparticles. Here we model the effects of silver nanoparticles (Ag-NPs) in a food chain consisting of soil-grown lettuce Lactuca sativa and snail Achatina fulica. Soil-grown lettuce were exposed to sulfurized Ag-NPs via root or metallic Ag-NPs via leaves before fed to snails. We discover an important biomagnification of silver in snails sourced from plant root uptake, with trophic transfer factors of 2.0-5.9 in soft tissues. NPs shifts from original size (55-68 nm) toward much smaller size (17-26 nm) in snails. Trophic transfer of Ag-NPs reprograms the global metabolic profile by down-regulating or up-regulating metabolites for up to 0.25- or 4.20- fold, respectively, relative to the control. These metabolites control osmoregulation, phospholipid, energy, and amino acid metabolism in snails, reflecting molecular pathways of biomagnification and pontential adverse biological effects on lower trophic levels. Consumption of these Ag-NP contaminated snails causes non-carcinogenic effects on human health. Global public health risks decrease by 72% under foliar Ag-NP application in agriculture or through a reduction in the consumption of snails sourced from root application. The latter strategy is at the expense of domestic economic losses in food security of $177.3 and $58.3 million annually for countries such as Nigeria and Cameroon. Foliar Ag-NP application in nano-agriculture has lower hazard quotient risks on public health than root application to ensure global food safety, as brought forward by the United Nations Sustainable Development Goals.
Phytoremediation is a biological remediation technique known for low-cost technology and environmentally friendly approach, which employs plants to extract, stabilise, and transform various compounds, such as potentially toxic elements (PTEs), in the soil or water. Recent developments in utilising chelating agents soil remediation have led to a renewed interest in chelate-induced phytoremediation. This review article summarises the roles of various chelating agents and the mechanisms of chelate-induced phytoremediation. This paper also discusses the recent findings on the impacts of chelating agents on PTEs uptake and plant growth and development in phytoremediation. It was found that the chelating agents have increased the rate of metal absorption and translocation up to 45% from roots to the aboveground plant parts during PTEs phytoremediation. Besides, it was also explored that the plants may experience some phytotoxicity after adding chelating agents to the soil. However, due to the leaching potential of synthetic chelating agents, the use of organic chelants have been explored to be used in PTEs phytoremediation. Finally, this paper also presents comprehensive insights on the significance of using chelating agents through SWOT analysis to discuss the advantages and limitations of chelate-induced phytoremediation.
Salinity stress adversely affects agricultural productivity by disrupting water uptake, causing nutrient imbalances, and leading to ion toxicity. Excessive salts in the soil hinder crops root growth and damage cellular functions, reducing photosynthetic capacity and inducing oxidative stress. Stomatal closure further limits carbon dioxide uptake that negatively impact plant growth. To ensure sustainable agriculture in salt-affected regions, it is essential to implement strategies like using biofertilizers (e.g. arbuscular mycorrhizae fungi = AMF) and activated carbon biochar. Both amendments can potentially mitigate the salinity stress by regulating antioxidants, gas exchange attributes and chlorophyll contents. The current study aims to explore the effect of EDTA-chelated biochar (ECB) with and without AMF on maize growth under salinity stress. Five levels of ECB (0, 0.2, 0.4, 0.6 and 0.8%) were applied, with and without AMF. Results showed that 0.8ECB + AMF caused significant enhancement in shoot length (~ 22%), shoot fresh weight (~ 15%), shoot dry weight (~ 51%), root length (~ 46%), root fresh weight (~ 26%), root dry weight (~ 27%) over the control (NoAMF + 0ECB). A significant enhancement in chlorophyll a, chlorophyll b and total chlorophyll content, photosynthetic rate, transpiration rate and stomatal conductance was also observed in the condition 0.8ECB + AMF relative to control (NoAMF + 0ECB), further supporting the efficacy of such a combined treatment. Our results suggest that adding 0.8% ECB in soil with AMF inoculation on maize seeds can enhance maize production in saline soils, possibly via improvement in antioxidant activity, chlorophyll contents, gas exchange and morphological attributes.