Displaying publications 61 - 80 of 121 in total

Abstract:
Sort:
  1. Optimization of degradation of Reactive Black 5 (RB5) and electricity generation in solar photocatalytic fuel cell system
    Khalik WF, Ho LN, Ong SA, Voon CH, Wong YS, Yusoff N, et al.
    Chemosphere, 2017 Oct;184:112-119.
    PMID: 28586651 DOI: 10.1016/j.chemosphere.2017.05.160
    The photocatalytic fuel cell (PFC) system was developed in order to study the effect of several operating parameters in degradation of Reactive Black 5 (RB5) and its electricity generation. Light irradiation, initial dye concentration, aeration, pH and cathode electrode are the operating parameters that might give contribution in the efficiency of PFC system. The degradation of RB5 depends on the presence of light irradiation and solar light gives better performance to degrade the azo dye. The azo dye with low initial concentration decolorizes faster compared to higher initial concentration and presence of aeration in PFC system would enhance its performance. Reactive Black 5 rapidly decreased at higher pH due to the higher amount of OH generated at higher pH and Pt-loaded carbon (Pt/C) was more suitable to be used as cathode in PFC system compared to Cu foil and Fe foil. The rapid decolorization of RB5 would increase their voltage output and in addition, it would also increase their Voc, Jsc and Pmax. The breakage of azo bond and aromatic rings was confirmed through UV-Vis spectrum and COD analysis.
    Matched MeSH terms: Sunlight
  2. Enhancement of simultaneous batik wastewater treatment and electricity generation in photocatalytic fuel cell
    Khalik WF, Ho LN, Ong SA, Voon CH, Wong YS, Yusuf SY, et al.
    Environ Sci Pollut Res Int, 2018 Dec;25(35):35164-35175.
    PMID: 30328543 DOI: 10.1007/s11356-018-3414-z
    The objective of this study was to investigate several operating parameters, such as open circuit, different external resistance, pH, supporting electrolyte, and presence of aeration that might enhance the degradation rate as well as electricity generation of batik wastewater in solar photocatalytic fuel cell (PFC). The optimum degradation of batik wastewater was at pH 9 with external resistor 250 Ω. It was observed that open circuit of PFC showed only 17.2 ± 7.5% of removal efficiency, meanwhile the degradation rate of batik wastewater was enhanced to 31.9 ± 15.0% for closed circuit with external resistor 250 Ω. The decolorization of batik wastewater in the absence of photocatalyst due to the absorption of light irradiation by dye molecules and this process was known as photolysis. The degradation of batik wastewater increased as the external resistor value decreased. In addition, the degradation rate of batik wastewater also increased at pH 9 which was 74.4 ± 34.9% and at pH 3, its degradation rate was reduced to 19.4 ± 8.7%. The presence of aeration and sodium chloride as supporting electrolyte in batik wastewater also affected its degradation and electricity generation. The maximum absorbance of wavelength (λmax) of batik wastewater at 535 nm and chemical oxygen demand gradually decreased as increased in irradiation time; however, batik wastewater required prolonged irradiation time to fully degrade and mineralize in PFC system.
    Matched MeSH terms: Sunlight
  3. Fulltext Photoprotective measures of selected sunscreens and their antioxidant adjuvantion effects in the Malaysian Climate
    Khamsiah, N., Lai, N.S., Nurfarhanim, M., Nor Aimi, A.R., Mohd Syazwan, C. S., Goon, J.A.
    Medicine & Health, 2012;7(2):84-96.
    MyJurnal
    The Malaysian skincare industry is growing rapidly with a vast number of new sunscreens being produced annually. Inadequate skincare regulations and lack of enforcement have resulted in the overrating of sunscreens’ quality. The objectives of this study were to evaluate the efficacy and safety of the local and international sunscreens and to determine the effects of adding concentrated antioxidants into them. Three local and three internationally manufactured sunscreens were tested for the in vitro Ultraviolet A protection factor (UVAPF), Sun Protection Factor (SPF) and photostability. The creams were spread onto roughened polymethylmethacrylate plates where the absorbance was measured using a spectrophotometer before and after two hours of sunlight irradiation. The procedure was repeated combining available concentrated vitamin C and E creams. International sunscreens were found to have more accurate SPF labels (p=0.009) while local sunscreens were found to be more photostable (p=0.003). However, both sunscreens had inadequate UVAPF (p=0.471). Vitamin C enhanced the SPF values (p= 0.04) of both groups of sunscreens while vitamin E enhanced their photostability (p=0.000). Interestingly, combining vitamins C and E rich creams with the sunscreens had no effect on the SPF and UVAPF values as compared to the use of a single vitamin. More importantly, the combination of vitamins decreased the photostability (p=0.002) of sunscreens as compared to the addition of vitamin E alone. In conclusion, photoprotection is best achieved when sunscreens are used together with creams containing either vitamin C or E alone.
    Matched MeSH terms: Sunlight
  4. Fulltext Gliding lizards use the position of the sun to enhance social display
    Klomp DA, Stuart-Fox D, Das I, Ord TJ
    Biol Lett, 2017 Feb;13(2).
    PMID: 28179410 DOI: 10.1098/rsbl.2016.0979
    Effective communication requires animal signals to be readily detected by receivers in the environments in which they are typically given. Certain light conditions enhance the visibility of colour signals and these conditions can vary depending on the orientation of the sun and the position of the signaller. We tested whether Draco sumatranus gliding lizards modified their position relative to the sun to enhance the conspicuousness of their throat-fan (dewlap) during social display to conspecifics. The dewlap was translucent, and we found that lizards were significantly more likely to orient themselves perpendicular to the sun when displaying. This increases the dewlap's radiance, and likely, its conspicuousness, by increasing the amount of light transmitted through the ornament. This is a rare example of a behavioural adaptation for enhancing the visibility of an ornament to distant receivers.
    Matched MeSH terms: Sunlight*
  5. Heterojunction photocatalysts for artificial nitrogen fixation: fundamentals, latest advances and future perspectives
    Lee J, Tan LL, Chai SP
    Nanoscale, 2021 Apr 21;13(15):7011-7033.
    PMID: 33889914 DOI: 10.1039/d1nr00783a
    As an indispensable energy source, ammonia plays an essential role in agriculture and various industries. Given that the current ammonia production is still dominated by the energy-intensive and high carbon footprint Haber-Bosch process, photocatalytic nitrogen fixation represents a low-energy consuming and sustainable approach to generate ammonia. Heterostructured photocatalysts are hybrid materials composed of semiconductor materials containing interfaces that make full use of the unique superiorities of the constituents and synergistic effects between them. These promising photocatalysts have superior performances and substantial potential in photocatalytic reduction of nitrogen. In this review, a wide spectrum of recently developed heterostructured photocatalysts for nitrogen fixation to ammonia are evaluated. The fundamentals of solar-to-ammonia conversion, basic principles of various heterojunction photocatalysts and modification strategies are systematically reviewed. Finally, a brief summary and perspectives on the ongoing challenges and directions for future development of nitrogen photofixation catalysts are also provided.
    Matched MeSH terms: Sunlight
  6. Exploring the relationship between molecular structure of dyes and light sources for photodegradation and electricity generation in photocatalytic fuel cell
    Lee SL, Ho LN, Ong SA, Wong YS, Voon CH, Khalik WF, et al.
    Chemosphere, 2018 Oct;209:935-943.
    PMID: 30114743 DOI: 10.1016/j.chemosphere.2018.06.157
    Reactive green 19, acid orange 7 and methylene blue are employed as the organic pollutants in this work. A photocatalytic fuel cell is constructed based on the idea of immobilizing zinc oxide onto zinc photoanode and platinum loaded carbon cathode, both evaluated under sunlight and ultraviolet irradiation, respectively. Influence of light and dye structures on the performance of photocatalytic fuel cell are examined. With reactive green 19, 93% and 86% of color removal are achieved after 8 h of photocatalytic fuel cell treatment under sunlight and ultraviolet irradiation, respectively. The decolorization rate of diazo reactive green 19 is higher than acid orange 7 (monoazo dye) when both dyes are treated by photocatalytic fuel cell under sunlight and ultraviolet irradiation, as the electron releasing groups (-NH-triazine) allow reactive green 19 easier to be oxidized. Comparatively, acid orange 7 is less favorable to be oxidized. The degradation of methylene blue is enhanced under sunlight irradiation due to the occurrence of self-sensitized photodegradation. When methylene blue is employed in the photocatalytic fuel cell under sunlight irradiation, the short circuit current (0.0129 mA cm-2) and maximum power density (0.0032 mW cm-2) of photocatalytic fuel cell greatly improved.
    Matched MeSH terms: Sunlight
  7. Amalgamation of N-graphene quantum dots with nanocubic like TiO2: an insight study of sunlight sensitive photocatalysis
    Lim PF, Leong KH, Sim LC, Abd Aziz A, Saravanan P
    Environ Sci Pollut Res Int, 2019 Feb;26(4):3455-3464.
    PMID: 30515688 DOI: 10.1007/s11356-018-3821-1
    In this work, a sunlight-sensitive photocatalyst of nanocubic-like titanium dioxide (TiO2) and N-doped graphene quantum dots (N-GQDs) is developed through a simple hydrothermal and physical mixing method. The successful amalgamation composite photocatalyst characteristics were comprehensively scrutinized through various physical and chemical analyses. A complete removal of bisphenol A (BPA) is attained by a synthesized composite after 30 min of sunlight irradiation as compared to pure TiO2. This clearly proved the unique contribution of N-GQDs that enhanced the ability of light harvesting especially under visible light and near-infrared region. This superior characteristic enables it to maximize the absorbance in the entire solar spectrum. However, the increase of N-GQDs weight percentage has created massive oxygen vacancies that suppress the generation of active radicals. This resulted in a longer duration for a complete removal of BPA as compared to lower weight percentage of N-GQDs. Hence, this finding can offer a new insight in developing effective sunlight-sensitive photocatalysts for various complex organic pollutants degradation.
    Matched MeSH terms: Sunlight
  8. Fulltext Boosting Photovoltaic Performance of Dye-Sensitized Solar Cells Using Silver Nanoparticle-Decorated N,S-Co-Doped-TiO2 Photoanode
    Lim SP, Pandikumar A, Lim HN, Ramaraj R, Huang NM
    Sci Rep, 2015;5:11922.
    PMID: 26146362 DOI: 10.1038/srep11922
    A silver nanoparticle-decorated N,S-co-doped TiO2 nanocomposite was successfully prepared and used as an efficient photoanode in high-performance dye-sensitized solar cells (DSSCs) with N719 dye. The DSSCs assembled with the N,S-TiO2@Ag-modified photoanode demonstrated an enhanced solar-to-electrical energy conversion efficiency of 8.22%, which was better than that of a DSSC photoanode composed of unmodified TiO2 (2.57%) under full sunlight illumination (100 mWcm(-2), AM 1.5 G). This enhanced efficiency was mainly attributed to the reduced band gap energy, improved interfacial charge transfer, and retarded charge recombination process. The influence of the Ag content on the overall efficiency was also investigated, and the optimum Ag content with N,S-TiO2 was found to be 20 wt%. Because of the enhanced solar energy conversion efficiency of the N,S-TiO2@Ag nanocomposite, it should be considered as a potential photoanode for high-performance DSSCs.
    Matched MeSH terms: Sunlight
  9. Fulltext Enhancing Photocurrent Performance Based on Photoanode Thickness and Surface Plasmon Resonance Using Ag-TiO2 Nanocomposites in Dye-Sensitized Solar Cells
    Lokman MQ, Shafie S, Shaban S, Ahmad F, Jaafar H, Mohd Rosnan R, et al.
    Materials (Basel), 2019 Jun 30;12(13).
    PMID: 31262020 DOI: 10.3390/ma12132111
    This study investigated the different thicknesses of TiO2 photoanode films and the effect of surface plasmon resonance (SPR) of Ag-TiO2 nanocomposites on the current-voltage (I-V) performance of dye-sensitized solar cells (DSSC). The TiO2 layer was deposited using the doctor blade technique and the thickness of the TiO2 films was controlled by using a different number of Scotch tape layers. The silver nanoparticles (AgNP) were synthesised using a chemical reduction method and the concentration of sodium citrate as a reducing agent was varied from 4 to 12 mM to study the effect of citrate ion on the size of the nanoparticles. Ag-TiO2 nanopowder was prepared by adding pure anatase TiO2 powder into AgNP colloidal solution. The mixture was left to dry for 24 h to obtain Ag-TiO2 powder for paste preparation. The three-layer Scotch tape, with thickness of 14.38 µm, achieved a high efficiency of 4.14%. This results showed that three layers was the optimal thickness to improve dye loading and to reduce the charge recombination rate. As for the Ag-TiO2 nanocomposites, 10 mM of AgNP, with a mean diameter of 65.23 nm and high efficiency of 6.92%, proved that SPR can enhance the absorption capability of dye and improve the photon-to-electron generation.
    Matched MeSH terms: Sunlight
  10. Developing correlation equations for converting among coliforms, E. coli and HPC for rainwater disinfection by sunlight
    M.T. Amin, M.Y. Han, Tschung-il Kim, A.A. Alazba, M.N. Amin
    Sains Malaysiana, 2013;42:1273-1281.
    The application of solar disinfection for treating stored rainwater was investigated by the authors using indicator organisms. The multiple tube fermentation technique and pour plate method were used for the detection of microbial quality indicators like total and fecal coliforms, E. coli and heterotrophic plate count. These techniques have disadvantages mainly that these are laborious and time consuming. The correlation of total coliform with that of exposure time is proposed under different factors of weather, pH and turbidity. Statistical tools like root mean square error and coefficient of determination were used to validate these proposed equations. The correlation equations of fecal coliform, E. coli and heterotrophic plate count with total coliform are suggested by using four regression analysis including Reciprocal Quadratic, Polynomial Regression (2 degree), Gaussian Model and Linear Regression in order to reduce the tedious experimental work in similar types of experiments and treatment systems.
    Matched MeSH terms: Sunlight
  11. Energy, exergy and efficiency analysis of a flat plate solar collector used as air heater
    Maazullah Khan, Abdurab, Muhammad Hanif, Mansoor Khan Khattak, Muhammad Ramzan
    Sains Malaysiana, 2018;47:1061-1067.
    Air heating by solar collectors is renewable technology providing hot air for different purposes. The present research
    emphasizes on analysis of energy, exergy and efficiency of a flat plate solar air heater. The analysis model was tested
    on five different air mass flow rates of 0.5 (Natural), 1.31, 2.11, 2.72 and 3.03 kgs-1 under three different tilt angles of
    25, 35 (Recommended) and 50o
    . The data was replicated three times making a total of 45 treatments. A two factorial
    completely randomized design was used to find if there is any significant difference among the treatments. The results
    showed that the solar collector gave better performance at air mass flow of 3.03 kgs-1 under tilt of 35o
    . At maximum
    air mass flow rate of 3.03 kgs-1and optimum tilt angle of 35o
    the maximum energetic efficiency of 51%, while minimum
    exergetic efficiency of 24% and maximum overall efficiency of 71% were recorded. It was concluded that to get maximum
    thermal efficiencies of 71% from flat plate solar collector used as an air heater must be operated at high air mass flow
    rates of 3.03 kgs-1under 35o
    tilt angle at Peshawar, Pakistan.
    Matched MeSH terms: Sunlight
  12. Fulltext Solar tree
    Madya Mastika binti Ahmad, Amirah binti Mohd Arif
    Journal of Engineering and Science Research, 2018;2(4):34-38.
    MyJurnal
    In this day and age, with the ever-growing population and energy demand, we should take the renewable option route in our energy source. We should also keep in mind that said energy should not cause any lasting environmental damage, one of the perfect example being solar energy. A country that is hot and sunny all year long is the perfect contributor to solar energy, case in point, Malaysia. With that in mind Solar Tree is designed and developed to facilitate consumers who need electric power at any place, anytime, anywhere. The objective of this study is to assess a mini project in the likes of Solar Tree that can generate electricity without harming the environment, despite the weather. Intended specifically to be a mini project, it is understandable that electricity generated is limited, with only up to 500W in total. As a trial, two electronic devices were tested, specifically a mobile phone and a laptop, as both devices are used almost every day. The data collected is then tabulated and analysed. It was concluded the solar tree developed proved efficient in charging both devices and will continue to do so given enough sunlight.
    Matched MeSH terms: Sunlight
  13. Influence of rain and malathion on the oviposition and development of blowflies (Diptera: Calliphoridae) infesting rabbit carcasses in Kelantan, Malaysia
    Mahat NA, Zafarina Z, Jayaprakash PT
    Forensic Sci Int, 2009 Nov 20;192(1-3):19-28.
    PMID: 19671490 DOI: 10.1016/j.forsciint.2009.07.008
    The influence of rain and malathion on the initial oviposition as well as development of blowfly species infesting rabbit carcasses decomposing in sunlit and shaded habitats were studied over a period of 1 year in Kelantan, Malaysia. Chrysomya megacephala (Fabricius) was the most dominant species that infested the carcasses, followed by Chrysomya rufifacies (Macquart). In general, rain, depending on its intensity, delayed initial oviposition by 1-2 days and prolonged the pupation period by 1-3 days. The presence of malathion in the carcasses delayed initial oviposition by 1-3 days and prolonged the pupation period by 2-3 days. These findings deserve consideration while estimating postmortem interval since rain is a commonplace occurrence in Malaysia and malathion is one of the common poisons as an agent for choice to commit suicide.
    Matched MeSH terms: Sunlight
  14. Fulltext Transparent Blend of Poly(Methylmethacrylate)/Cellulose Acetate Butyrate for the Protection from Ultraviolet
    Mahmood Raouf R, Abdul Wahab Z, Azowa Ibrahim N, Abidin Talib Z, Chieng BW
    Polymers (Basel), 2016 Apr 14;8(4).
    PMID: 30979233 DOI: 10.3390/polym8040128
    The use of transparent polymers as an alternative to glass has become widespread. However, the direct exposure of these materials to climatic conditions of sunlight and heat decrease the lifetime cost of these products. The aim of this study was to minimize the harm caused by ultraviolet (UV) radiation exposure to transparent poly(methylmethacrylate) (PMMA), which usually leads to changes in the physical and chemical properties of these materials and reduced performance. This was achieved using environmentally friendly cellulose acetate butyrate (CAB). The optical, morphological, and thermal properties of CAB blended with transparent PMMA was studied using UV-VIS spectrophotometry, scanning electron microscopy, X-ray diffraction, dynamic mechanical analysis, and thermal gravimetric analysis. The results show that CAB was able to reduce the effects of UV radiation by making PMMA more transparent to UV light, thereby preventing the negative effects of trapped radiation within the compositional structure, while maintaining the amorphous structure of the blend. The results also show that CAB blended with PMMA led to some properties commensurate with the requirements of research in terms of a slight increase in the value of the modulus and the glass transition temperature for the PMMA/CAB blend.
    Matched MeSH terms: Sunlight
  15. Fulltext Thermal tolerance and climate warming sensitivity in tropical snails
    Marshall DJ, Rezende EL, Baharuddin N, Choi F, Helmuth B
    Ecol Evol, 2015 12;5(24):5905-19.
    PMID: 26811764 DOI: 10.1002/ece3.1785
    Tropical ectotherms are predicted to be especially vulnerable to climate change because their thermal tolerance limits generally lie close to current maximum air temperatures. This prediction derives primarily from studies on insects and lizards and remains untested for other taxa with contrasting ecologies. We studied the HCT (heat coma temperatures) and ULT (upper lethal temperatures) of 40 species of tropical eulittoral snails (Littorinidae and Neritidae) inhabiting exposed rocky shores and shaded mangrove forests in Oceania, Africa, Asia and North America. We also estimated extremes in animal body temperature at each site using a simple heat budget model and historical (20 years) air temperature and solar radiation data. Phylogenetic analyses suggest that HCT and ULT exhibit limited adaptive variation across habitats (mangroves vs. rocky shores) or geographic locations despite their contrasting thermal regimes. Instead, the elevated heat tolerance of these species (HCT = 44.5 ± 1.8°C and ULT = 52.1 ± 2.2°C) seems to reflect the extreme temperature variability of intertidal systems. Sensitivity to climate warming, which was quantified as the difference between HCT or ULT and maximum body temperature, differed greatly between snails from sunny (rocky shore; Thermal Safety Margin, TSM = -14.8 ± 3.3°C and -6.2 ± 4.4°C for HCT and ULT, respectively) and shaded (mangrove) habitats (TSM = 5.1 ± 3.6°C and 12.5 ± 3.6°C). Negative TSMs in rocky shore animals suggest that mortality is likely ameliorated during extreme climatic events by behavioral thermoregulation. Given the low variability in heat tolerance across species, habitat and geographic location account for most of the variation in TSM and may adequately predict the vulnerability to climate change. These findings caution against generalizations on the impact of global warming across ectothermic taxa and highlight how the consideration of nonmodel animals, ecological transitions, and behavioral responses may alter predictions of studies that ignore these biological details.
    Matched MeSH terms: Sunlight
  16. Fulltext Photochemical Synthesis of Nanosheet Tin Di/Sulfide with Sunlight Response on Water Pollutant Degradation
    Matmin J, Jalani MA, Osman H, Omar Q, Ab'lah N, Elong K, et al.
    Nanomaterials (Basel), 2019 Feb 14;9(2).
    PMID: 30769911 DOI: 10.3390/nano9020264
    The photochemical synthesis of two-dimensional (2D) nanostructured from semiconductor materials is unique and challenging. We report, for the first time, the photochemical synthesis of 2D tin di/sulfide (PS-SnS₂-x, x = 0 or 1) from thioacetamide (TAA) and tin (IV) chloride in an aqueous system. The synthesized PS-SnS₂-x were characterized by X-ray diffraction (XRD), energy dispersive X-ray spectroscopy (EDX), field emission scanning electron microscopy (FESEM), transmission electron microscopy (TEM), a particle size distribution analyzer, X-ray photoelectron spectroscopy (XPS), Fourier-transform infrared spectroscopy (FTIR), thermal analysis, UV⁻Vis diffuse reflectance spectroscopy (DR UV⁻Vis), and photoluminescence (PL) spectroscopy. In this study, the PS-SnS₂-x showed hexagonally closed-packed crystals having nanosheets morphology with the average size of 870 nm. Furthermore, the nanosheets PS-SnS₂-x demonstrated reusable photo-degradation of methylene blue (MB) dye as a water pollutant, owing to the stable electronic conducting properties with estimated bandgap (Eg) at ~2.5 eV. Importantly, the study provides a green protocol by using photochemical synthesis to produce 2D nanosheets of semiconductor materials showing photo-degradation activity under sunlight response.
    Matched MeSH terms: Sunlight
  17. Comparison of UVA vs UVB Photoaging Rat Models in Short-term Exposure
    Mayangsari E, Mustika A, Nurdiana N, Samad NA
    Med Arch, 2024;78(2):88-91.
    PMID: 38566862 DOI: 10.5455/medarh.2024.78.88-91
    BACKGROUND: Prolonged exposure to sunlight is known to induce photoaging of the skin, leading to various skin changes and disorders, such as dryness, wrinkles, irregular pigmentation, and even cancer. Ultraviolet A (UVA) and ultraviolet B (UVB) radiation are particularly responsible for causing photoaging.

    OBJECTIVE: This study aims to identify and compare photoaging rat models exposed to UVA and UVB.

    METHODS: This research method compared macroscopic (scoring degree of wrinkling) and microscopic (histology) signs and symptoms on skin samples of rat exposed to UVA and UVB for 4 weeks at a radiation dose of 840mJ/cm2.

    RESULTS: The results of this study indicated that the degree of wrinkling was highest in rat skin exposed to UVB rays by 51% (p<0.05). UVB histological results showed that the epidermis layer (40 µm, p<0.05) was thickened and the dermis layer (283 µm, p<0.05) was thinned in the skin of mice exposed to UVB light. The UVB group, showed the density of collagen in the dermis with a mean value of 55% (p<0.05).

    CONCLUSION: Our results suggest that short-term exposure to UVB radiation (in the acute, subacute or subchronic phase) induces more rapid and pronounced damage to rat skin when compared to UVA radiation exposure.

    Matched MeSH terms: Sunlight
  18. Comparative studies of RSM Box-Behnken and ANN-Anfis fuzzy statistical analysis for seawater biodegradability using TiO2 photocatalyst
    Mohammed N, Palaniandy P, Shaik F, Mewada H, Balakrishnan D
    Chemosphere, 2023 Feb;314:137665.
    PMID: 36581118 DOI: 10.1016/j.chemosphere.2022.137665
    In this approach, a batch reactor was employed to study the degradation of pollutants under natural sunlight using TiO2 as a photocatalyst. The effects of photocatalyst dosage, reaction time and pH were investigated by evaluating the percentage removal efficiencies of total organic carbon (TOC), chemical oxygen demand (COD), biological oxygen demand (BOD) and biodegradability (BOD/COD). Design Expert-Response Surface Methodology Box Behnken Design (BBD) and MATLAB Artificial Neural Network - Adaptive Neuro Fuzzy Inference system (ANN-ANFIS) methods were employed to perform the statistical modelling. The experimental values of maximum percentage removal efficiencies were found to be TOC = 82.4, COD = 85.9, BOD = 30.9% and biodegradability was 0.070. According to RSM-BBD and ANFIS analysis, the maximum percentage removal efficiencies were found to be TOC = 90.3, 82.4; COD = 85.4, 85.9; BOD = 28.9, 30.9% and the biodegradability = 0.074, 0.080 respectively at the pH 7.5, reaction time 300 min and photocatalyst dosage of 4 g L-1. The study reveals both models found to be well predicted as compared with experimental values. The values of R2 for RSM-BBD (0.920) and for ANFIS (0.990) models were almost close to 1. The ANFIS model was found to be marginally better than that of RSM-BBD.
    Matched MeSH terms: Sunlight
  19. Fulltext Sun exposure, dietary vitamin d and vitamin d status in adult atopic dermatitis: a case control study
    Mohan Arumugam1, Adawiyah Jamil1, Norazirah Md Nor, Mazlin Baseri, Norlaila Mustafa, Suganthi Thevarajah
    Malaysian Journal of Medicine and Health Sciences, 2020;16(1):66-69.
    MyJurnal
    Introduction: Atopic dermatitis (AD) and its severity has been inconsistently associated with lower vitamin D levels as multiple other factors that influence vitamin D status were not always assessed. Methods: A case control study involving AD patients and controls 18 years old was performed. Exclusion criteria were systemic immunosuppres- sion  4 weeks prior to recruitment, renal or hepatic impairment, parathyroid diseases and vitamin D or calcium supplementation. Healthy controls were matched for age, gender, ethnicity, Fitzpatrick skin type and body mass index (BMI). Sun exposure, a 3-day, 24-hour dietary recall and serum 25-hydroxyvitamin D were measured. Re- sults: 38 AD patients and 38 controls participated. Majority had Fitzpatrick skin type IV. Vitamin D was lower in AD [15.9(9.9-24.0)ng/ml] than controls [17.3(14.4-27.2)ng/ml], p= 0.028. It was sufficient in 16(42.1%) AD and 15(39.5%) controls, insufficient in 7(18.4%) AD and 22(57.9%) controls and deficient in 15(39.5%) AD compared to 1(2.6%) control. Sun exposure was similar in both groups. AD had significantly higher dietary vitamin D intake [1.5(0.6-3.1) vs 0.6 (0.3-1.0)µg]. AD was an independant risk for vitamin D deficiency with OR 17.52; 95%CI:1.4-
    212.7 and vitamin D insufficiency OR 0.26;95%CI:0.07-0.95. Vitamin D levels did not correlate with AD severity. Conclusion: AD is a risk for vitamin D deficiency despite higher dietary intake and similar skin type, BMI and sun exposure as controls.
    Matched MeSH terms: Sunlight
  20. Vitamin D status and its associated factors of free living Malay adults in a tropical country, Malaysia
    Moy FM
    J. Photochem. Photobiol. B, Biol., 2011 Sep 02;104(3):444-8.
    PMID: 21636288 DOI: 10.1016/j.jphotobiol.2011.05.002
    Vitamin D status is influenced by sun exposure, geographic latitude, daily outdoor activities, body surface exposed to sunlight and dietary intakes. Malaysia, is sunny all year round. However, the vitamin D status of this population especially among the healthy and free living adults is not known. Therefore a study of vitamin D status and associated factors was initiated among an existing Malay cohort in Kuala Lumpur. A total of 380 subjects were sampled to have their vitamin D status assessed using 25-hydroxyvitamin D (25(OH)D). A short questionnaire enquiring socio-demographic characteristics, exposure to sunlight and clothing style was administered. Their mean age was 48.5±5.2years and the mean 25(OH)D for males and females were 56.2±18.9nmol/L and 36.2±13.4nmol/L respectively. There were significant positive correlation for sun exposure score (r=0.27, p<0.001) and negative correlation for sun protection score (r=-0.41, p<0.001) with 25(OH)D levels. In the logistic regression model, females (OR=2.93; 95% CI: 1.17, 7.31), BMI (1.1; 1.03, 1.20) and sun exposure score (0.998; 0.996, 0.999) were significantly associated with vitamin D status as represented by 25(OH)D levels. Our findings show that obesity, lifestyle behaviours and clothing style are directly associated with our participants especially females' low vitamin D status.
    Matched MeSH terms: Sunlight
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links