Displaying publications 61 - 80 of 449 in total

Abstract:
Sort:
  1. Physicochemical characterization of cellulose nanocrystal and nanoporous self-assembled CNC membrane derived from Ceiba pentandra
    Mohamed MA, W Salleh WN, Jaafar J, Ismail AF, Abd Mutalib M, Mohamad AB, et al.
    Carbohydr Polym, 2017 Feb 10;157:1892-1902.
    PMID: 27987909 DOI: 10.1016/j.carbpol.2016.11.078
    This research involves the rare utilisation of the kapok fibre (Ceiba pentandra) as a raw material for the fabrication of cellulose nanocrystal (CNC) and self-assembled CNC membranes. The isolation of CNC from Ceiba pentandra began with the extraction of cellulose via the chemical alkali extraction by using 5wt% NaOH, followed by the typical acidified bleaching method and, finally, the CNC production through acid hydrolysis with 60wt% H2SO4 at the optimum time of 60min. The prepared CNC was then employed for the preparation of self-assembled membrane through the water suspension casting evaporation technique. The obtained CNC membrane was characterised in terms of its composition, crystallinity, thermal stability, as well as, structural and morphological features with the use of several techniques including FTIR, XRD, AFM, TEM, FESEM, and TGA. The FESEM and AFM analyses had illustrated the achievement of a self-assembled CNC membrane with a smooth surface and a well-distributed nano-porous structure, with the porosity of 52.82±7.79%. In addition, the findings proved that the self-assembled CNC membrane displayed good adsorption capability indicated by the recorded efficiency of 79% and 85% for 10mg/L and 5mg/L of methylene blue in an aqueous solution, respectively.
    Matched MeSH terms: Cellulose*
  2. Bio-waste corn-cob cellulose supported poly(hydroxamic acid) copper complex for Huisgen reaction: Waste to wealth approach
    Mandal BH, Rahman ML, Yusoff MM, Chong KF, Sarkar SM
    Carbohydr Polym, 2017 Jan 20;156:175-181.
    PMID: 27842811 DOI: 10.1016/j.carbpol.2016.09.021
    Corn-cob cellulose supported poly(hydroxamic acid) Cu(II) complex was prepared by the surface modification of waste corn-cob cellulose through graft copolymerization and subsequent hydroximation. The complex was characterized by IR, UV, FESEM, TEM, XPS, EDX and ICP-AES analyses. The complex has been found to be an efficient catalyst for 1,3-dipolar Huisgen cycloaddition (CuAAC) of aryl/alkyl azides with a variety of alkynes as well as one-pot three-components reaction in the presence of sodium ascorbate to give the corresponding cycloaddition products in up to 96% yield and high turn over number (TON 18,600) and turn over frequency (TOF 930h-1) were achieved. The complex was easy to recover from the reaction mixture and reused six times without significant loss of its catalytic activity.
    Matched MeSH terms: Cellulose/chemistry*
  3. Integrated pretreatment of poplar biomass employing p-toluenesulfonic acid catalyzed liquid hot water and short-time ball milling for complete conversion to xylooligosaccharides, glucose, and native-like lignin
    Madadi M, Liu D, Qin Y, Zhang Y, Karimi K, Tabatabaei M, et al.
    Bioresour Technol, 2023 Sep;384:129370.
    PMID: 37343805 DOI: 10.1016/j.biortech.2023.129370
    This work aimed to study an integrated pretreatment technology employing p-toluenesulfonic acid (TsOH)-catalyzed liquid hot water (LHW) and short-time ball milling for the complete conversion of poplar biomass to xylooligosaccharides (XOS), glucose, and native-like lignin. The optimized TsOH-catalyzed LHW pretreatment solubilized 98.5% of hemicellulose at 160 °C for 40 min, releasing 49.8% XOS. Moreover, subsequent ball milling (20 min) maximized the enzymatic hydrolysis of cellulose from 65.8% to 96.5%, owing to the reduced particle sizes and cellulose crystallinity index. The combined pretreatment reduced the crystallinity by 70.9% while enlarging the average pore size and pore volume of the substrate by 29.5% and 52.4%, respectively. The residual lignin after enzymatic hydrolysis was rich in β-O-4 linkages (55.7/100 Ar) with less condensed structures. This lignin exhibited excellent antioxidant activity (RSI of 66.22) and ultraviolet absorbance. Thus, this research suggested a sustainable waste-free biorefinery for the holistic valorization of biomass through two-step biomass fractionation.
    Matched MeSH terms: Cellulose/chemistry
  4. Fractionation and physicochemical characterization of dietary fiber of kenaf (Hibiscus cannabinus L.) seed
    Nevara GA, Muhammad SKS, Zawawi N, Mustapha NA, Karim R
    J Sci Food Agric, 2024 Apr;104(6):3216-3227.
    PMID: 38072678 DOI: 10.1002/jsfa.13208
    BACKGROUND: Kenaf seeds are underutilized kenaf plant by-products, containing essential nutrients including dietary fiber (DF), which can be potentially utilized as food ingredients. The present study aimed to evaluate the physicochemical characteristics of kenaf seed fiber fractions extracted from kenaf seed.

    RESULTS: Defatted kenaf seed powder yielded four DF fractions: alkali-soluble hemicellulose (146.4 g kg-1 ), calcium-bound pectin (10.3 g kg-1 ) and acid-soluble pectin (25.4 g kg-1 ) made up the soluble fibre fraction, whereas cellulose (202.2 g kg-1 ) comprised the insoluble fraction. All fractions were evaluated for their physicochemical properties. The DF fractions contained glucose, mannose, xylose and arabinose, and a small amount of uronic acid (1.2-2.7 g kg-1 ). The isolated pectin fractions had a low degree of esterification (14-30%). All the isolated DF fractions had high average molecular weights ranging from 0.3 to 4.3 × 106 g mol-1 . X-ray diffractogram analysis revealed that the fractions consisted mainly of an amorphous structure with a relative crystallinity ranging from 31.6% to 44.1%. The Fourier-transform infrared spectroscopy spectrum of kenaf seed and its DF fractions showed typical absorption of polysaccharides, with the presence of hydroxyl, carboxyl, acetyl and methyl groups. Scanning electron microscopy analysis demonstrated that the raw material with the rigid structure resulted in soluble and insoluble DF fractions with more fragile and fibrous appearances, respectively. The soluble DF demonstrated greater flowability and compressibility than the insoluble fractions.

    CONCLUSION: These findings provide novel information on the DF fractions of kenaf seeds, which could be used as a potential new DF for the food industry. © 2023 Society of Chemical Industry.

    Matched MeSH terms: Cellulose/analysis
  5. Fulltext Scalable mesoporous biochars from bagasse waste for Cu (II) removal: Process optimisation, kinetics and techno-economic analysis
    Bongosia JG, Al-Gailani A, Kolosz BW, Loy Chun Minh A, Lock SSM, Cheah KW, et al.
    J Environ Manage, 2024 Nov;370:122558.
    PMID: 39303585 DOI: 10.1016/j.jenvman.2024.122558
    As the world faces the brink of climatological disaster, it is crucial to utilize all available resources to facilitate environmental remediation, especially by accommodating waste streams. Lignocellulosic waste residues can be transformed into mesoporous biochar structures with substantial pore capacity. While biochars are considered a method of carbon dioxide removal (CDR), they are in fact an environmental double-edged sword that can be used to extract metal ions from water bodies. Biochars possess high chemical affinities through chemisorption pathways that are tuneable to specific pH conditions. This work demonstrates how biochars can be enhanced to maximise their surface area and porosity for the removal of Cu (II) in solution. It was found that bagasse derived mesoporous biochars operate preferentially at high pH (basic conditions), with the 1.18 mKOH/mSCB material reaching 97.85% Cu (II) removal in 5 min. This result is in stark contrast with the majority of biochar adsorbents that are only effective at low pH (acidic conditions). As a result, the biochars produced in this work can be directly applied to ancestral landfill sites and carbonate-rich mine waters which are highly basic by nature, preventing further metal infiltration and reverse sullied water supplies. Furthermore, to assess the value in the use of biochars produced and applied in this way, a techno-economic assessment was carried out to determine the true cost of biochar synthesis, with possible routes for revenue post-Cu being removed from the biochar.
    Matched MeSH terms: Cellulose/chemistry
  6. Isolation and characterization of microcrystalline cellulose from oil palm biomass residue
    Mohamad Haafiz MK, Eichhorn SJ, Hassan A, Jawaid M
    Carbohydr Polym, 2013 Apr 2;93(2):628-34.
    PMID: 23499105 DOI: 10.1016/j.carbpol.2013.01.035
    In this work, we successfully isolated microcrystalline cellulose (MCC) from oil palm empty fruit bunch (OPEFB) fiber-total chlorine free (TCF) pulp using acid hydrolysis method. TCF pulp bleaching carried out using an oxygen-ozone-hydrogen peroxide bleaching sequence. Fourier transform infrared (FT-IR) spectroscopy indicates that acid hydrolysis does not affect the chemical structure of the cellulosic fragments. The morphology of the hydrolyzed MCC was investigated using scanning electron microscopy (SEM), showing a compact structure and a rough surface. Furthermore, atomic force microscopy (AFM) image of the surface indicates the presence of spherical features. X-ray diffraction (XRD) shows that the MCC produced is a cellulose-I polymorph, with 87% crystallinity. The MCC obtained from OPEFB-pulp is shown to have a good thermal stability. The potential for a range of applications such as green nano biocomposites reinforced with this form of MCC and pharmaceutical tableting material is discussed.
    Matched MeSH terms: Cellulose/isolation & purification*; Cellulose/ultrastructure; Cellulose/chemistry*
  7. Production of an oligosaccharide-specific cellobiohydrolase from the thermophilic fungus Thielavia terrestris
    Woon JS, Mackeen MM, Sudin AH, Mahadi NM, Illias RM, Murad AM, et al.
    Biotechnol Lett, 2016 May;38(5):825-32.
    PMID: 26830095 DOI: 10.1007/s10529-016-2045-z
    To express and determine the hydrolytic activity of a cellobiohydrolase (TTCBH6B) from the thermophilic fungus Thielavia terrestris in Pichia pastoris.
    Matched MeSH terms: Cellulose 1,4-beta-Cellobiosidase
  8. Cellulose acetate from oil palm empty fruit bunch via a one step heterogeneous acetylation
    Wan Daud WR, Djuned FM
    Carbohydr Polym, 2015 Nov 5;132:252-60.
    PMID: 26256348 DOI: 10.1016/j.carbpol.2015.06.011
    Acetone soluble oil palm empty fruit bunch cellulose acetate (OPEFB-CA) of DS 2.52 has been successfully synthesized in a one-step heterogeneous acetylation of OPEFB cellulose without necessitating the hydrolysis stage. This has only been made possible by the mathematical modeling of the acetylation process by manipulating the variables of reaction time and acetic anhydride/cellulose ratio (RR). The obtained model was verified by experimental data with an error of less than 2.5%. NMR analysis showed that the distribution of the acetyl moiety among the three OH groups of cellulose indicates a preference at the C6 position, followed by C3 and C2. XRD revealed that OPEFB-CA is highly amorphous with a degree of crystallinity estimated to be ca. 6.41% as determined from DSC. The OPEFB-CA films exhibited good mechanical properties being their tensile strength and Young's modulus higher than those of the commercial CA.
    Matched MeSH terms: Cellulose/analogs & derivatives*; Cellulose/chemical synthesis; Cellulose/chemistry
  9. Characterization of microcrystalline cellulose extracted from olive fiber
    Kian LK, Saba N, Jawaid M, Fouad H
    Int J Biol Macromol, 2020 Aug 01;156:347-353.
    PMID: 32278601 DOI: 10.1016/j.ijbiomac.2020.04.015
    Olive fiber is a renewable natural fiber which has potential as an alternative biomass for extraction of microcrystalline cellulose (MCC). MCC has been widely applied in various industries owing to its small dimensional size for ease of reactive fabrication process. At present study, a serial treatments of bleaching, alkaline and acid hydrolysis was employed to extract OL-BLF, OL-PUF, and OL-MCC respectively from olive stem fiber. In morphology examination, a feature of short micro-crystallite particles was obtained for OL-MCC. The particle size was found gradually reducing from OL-PUF (305.31 μm) to OL-MCC (156.06 μm) due to the disintegration of cellulose fibrils. From physicochemical analysis, most lignin and hemicellulose components had been removed from OL-BLF to form OL-PUF with individually fibril structure. The elemental analysis revealed that highly pure cellulose component was obtained for OL-MCC. Also, the rigidity had been improved from OL-BLF to OL-PUF, while with the highest for OL-MCC with 74.2% crystallinity, endowing it as a reliable load-bearing agent. As for thermal analysis, OL-MCC had the most stable heat resistance in among the chemically-treated fibers. Therefore, olive MCC could act as a promising reinforcing agent to withstand harsh conditions for variety fields of composite applications.
    Matched MeSH terms: Cellulose/isolation & purification; Cellulose/ultrastructure; Cellulose/chemistry*
  10. Fulltext Enhancement of Versatile Extracellular Cellulolytic and Hemicellulolytic Enzyme Productions by Lactobacillus plantarum RI 11 Isolated from Malaysian Food Using Renewable Natural Polymers
    Mohamad Zabidi NA, Foo HL, Loh TC, Mohamad R, Abdul Rahim R
    Molecules, 2020 Jun 03;25(11).
    PMID: 32503356 DOI: 10.3390/molecules25112607
    Lactobacillus plantarum RI 11 was reported recently to be a potential lignocellulosic biomass degrader since it has the capability of producing versatile extracellular cellulolytic and hemicellulolytic enzymes. Thus, this study was conducted to evaluate further the effects of various renewable natural polymers on the growth and production of extracellular cellulolytic and hemicellulolytic enzymes by this novel isolate. Basal medium supplemented with molasses and yeast extract produced the highest cell biomass (log 10.51 CFU/mL) and extracellular endoglucanase (11.70 µg/min/mg), exoglucanase (9.99 µg/min/mg), β-glucosidase (10.43 nmol/min/mg), and mannanase (8.03 µg/min/mg), respectively. Subsequently, a statistical optimization approach was employed for the enhancement of cell biomass, and cellulolytic and hemicellulolytic enzyme productions. Basal medium that supplemented with glucose, molasses and soybean pulp (F5 medium) or with rice straw, yeast extract and soybean pulp (F6 medium) produced the highest cell population of log 11.76 CFU/mL, respectively. However, formulated F12 medium supplemented with glucose, molasses and palm kernel cake enhanced extracellular endoglucanase (4 folds), exoglucanase (2.6 folds) and mannanase (2.6 folds) specific activities significantly, indicating that the F12 medium could induce the highest production of extracellular cellulolytic and hemicellulolytic enzymes concomitantly. In conclusion, L. plantarum RI 11 is a promising and versatile bio-transformation agent for lignocellulolytic biomass.
    Matched MeSH terms: Cellulose/metabolism*; Cellulose 1,4-beta-Cellobiosidase/metabolism*
  11. Fulltext A Precise Prediction Method for the Properties of API-Containing Tablets Based on Data from Placebo Tablets
    Hayashi Y, Shirotori K, Kosugi A, Kumada S, Leong KH, Okada K, et al.
    Pharmaceutics, 2020 Jun 28;12(7).
    PMID: 32605318 DOI: 10.3390/pharmaceutics12070601
    We previously reported a novel method for the precise prediction of tablet properties (e.g., tensile strength (TS)) using a small number of experimental data. The key technique of this method is to compensate for the lack of experimental data by using data of placebo tablets collected in a database. This study provides further technical knowledge to discuss the usefulness of this prediction method. Placebo tablets consisting of microcrystalline cellulose, lactose, and cornstarch were prepared using the design of an experimental method, and their TS and disintegration time (DT) were measured. The response surfaces representing the relationship between the formulation and the tablet properties were then created. This study investigated tablets containing four different active pharmaceutical ingredients (APIs) with a drug load ranging from 20-60%. Overall, the TS of API-containing tablets could be precisely predicted by this method, while the prediction accuracy of the DT was much lower than that of the TS. These results suggested that the mode of action of APIs on the DT was more complicated than that on the TS. Our prediction method could be valuable for the development of tablet formulations.
    Matched MeSH terms: Cellulose
  12. Sustainable and cost-effective approach for the synthesis of lignin-containing cellulose nanocrystals from oil palm empty fruit bunch
    Teh KC, Foo ML, Ooi CW, Leng Chew IM
    Chemosphere, 2021 Mar;267:129277.
    PMID: 33385850 DOI: 10.1016/j.chemosphere.2020.129277
    Cellulose nanocrystals (CNC) have received great research attention since the last few decades due to their extraordinary properties and wide range of applications. In this study, a sustainable and cost-effective method for the synthesis of lignin-containing cellulose nanocrystals (LCNC) from oil palm empty fruit bunch (EFB) is presented. This method is able to retain the lignin in EFB and manifest the properties of lignin. The proposed synthesis process is simpler than the conventional method of producing lignin-coated CNC by first removing the lignin to synthesize CNC followed by the re-coating of lignin on the structure. The samples of LCNC were characterized by transmission electron microscopy, X-ray diffraction, Fourier-transform infrared spectroscopy and water contact angle analysis. In addition, by altering the acid concentration during acid hydrolysis process (53% - 60% H2SO4), both surface hydrophobicity (66.0° - 75.1°) and length of LCNC (467 nm-177 nm) can be altered wherein a higher concentration of acid resulted in a greater contact angle and a shorter length of LCNC. Cost and energy analysis deduced that the proposed synthesis method saved about 62% of the total material cost and 80% less energy as compared to the synthesis of lignin-coated CNC.
    Matched MeSH terms: Cellulose
  13. Simultaneous production of cellulase and reducing sugar through modification of compositional and structural characteristic of sugarcane bagasse
    Yoon LW, Ngoh GC, Chua AS
    Enzyme Microb Technol, 2013 Sep 10;53(4):250-6.
    PMID: 23931690 DOI: 10.1016/j.enzmictec.2013.05.005
    This study examined the potential of untreated and alkali-pretreated sugarcane bagasse (SCB) in cellulase, reducing sugar (RS) and fungal biomass production via solid state fermentation (SSF) using Pycnoporus sanguineus. The impact of the composition, structure and cellulase adsorption ability of SCB on the production of cellulase, RS and fungal biomass was investigated. From the morphological and compositional analyses, untreated SCB has relatively more structural changes with a higher percentage of depolymerisation on the cellulose, hemicellulose and lignin content compared to alkali-pretreated SCB. Thus, untreated SCB favoured the production of cellulase and fungal biomass whereas alkali-pretreated SCB yielded a higher amount of RS. The composition and morphology of untreated SCB did not encourage RS production and this suggested that RS produced during SSF might be consumed in a faster rate by the more abundantly grown fungus. Besides that, alkali-pretreated SCB with higher cellulase adsorption ability could have adsorbed the cellulase produced and resulted in a lower cellulase titre. In short, the production of specific bioproducts via SSF is dependent on the structure and composition of the substrate applied.
    Matched MeSH terms: Cellulose/metabolism*; Cellulose/ultrastructure; Cellulose/chemistry
  14. Stability evaluation and formula optimization of cellulose-based scaffold for the air-liquid interface cultivation of Navicula incerta
    Yap JX, Leo CP, Mohd Yasin NH, Show PL, Derek CJC
    Environ Res, 2021 08;199:111298.
    PMID: 33971133 DOI: 10.1016/j.envres.2021.111298
    Culture scaffolds allow microalgae cultivation with minimum water requirement using the air-liquid interface approach. However, the stability of cellulose-based scaffolds in microalgae cultivation remains questionable. In this study, the stability of regenerated cellulose culture scaffolds was enhanced by adjusting TiO2 loading and casting gap. The membrane scaffolds were synthesized using cellulose dissolved in NaOH/urea aqueous solution with various loading of TiO2 nanoparticles. The TiO2 nanoparticles were embedded into the porous membrane scaffolds as proven by Fourier transform infrared spectra, scanning electron microscopic images, and energy-dispersive X-ray spectra. Although surface hydrophilicity and porosity were enhanced by increasing TiO2 and casting gap, the scaffold pore size was reduced. Cellulose membrane scaffold with 0.05 wt% of TiO2 concentration and thickness of 100 μm attained the highest percentage of Navicula incerta growth rate, up to 37.4%. The membrane scaffolds remained stable in terms of weight, porosity and pore size even they were immersed in acidic solution, hydrogen peroxide or autoclaved at 121 °C for 15 min. The optimal cellulose membrane scaffold is with TiO2 loading of 0.5 wt% and thickness of 100 μm, resulting in supporting the highest N. incerta growth rate and and exhibits good membrane stability.
    Matched MeSH terms: Cellulose
  15. A review on the emerging applications of cellulose, cellulose derivatives and nanocellulose in carbon capture
    Ho NAD, Leo CP
    Environ Res, 2021 06;197:111100.
    PMID: 33812871 DOI: 10.1016/j.envres.2021.111100
    Carbon capture can be implemented at a large scale only if the CO2 selective materials are abundantly available at low cost. Since the sustainable requirement also elevated, the low-cost and biodegradable cellulosic materials are developed into CO2 selective adsorbent and membranes recently. The applications of cellulose, cellulosic derivatives and nanocellulose as CO2 selective adsorbents and membranes are reviewed here. The fabrication and modification strategies are discussed besides comparing their CO2 separation performance. Cellulose nanofibrils (CNFs) and cellulose nanocrystals (CNCs) isolated from cellulose possess a big surface area for mechanical enhancement and a great number of hydroxyl groups for modification. Nanocellulose aerogels with the large surface area were chemically modified to improve their selectivity towards CO2. Even with the reduction of surface area, amino-functionalized nanocellulose aerogels exhibited the satisfactory chemisorption of CO2 with a capacity of more than 2 mmol/g was recorded. Inorganic fillers such as silica, zeolite and MOFs were further incorporated into nanocellulose aerogels to enhance the physisorption of CO2 by increasing the surface area. Although CO2 adsorbents developed from cellulose and cellulose derivatives were less reported, their applications as the building blocks of CO2 separation membranes had been long studied. Cellulose acetate membranes were commercialized for CO2 separation, but their separation performance could be further improved with silane or inorganic filler. CNCs and CNFs enhanced the CO2 selectivity and permeance through polyvinyl alcohol coating on membranes, but only CNF membranes incorporated with MOFs were explored so far. Although some of these membranes surpassed the upper-bound of Robeson plot, their stability should be further investigated.
    Matched MeSH terms: Cellulose
  16. Physicochemical of microcrystalline cellulose from oil palm fronds as potential methylene blue adsorbents
    Hussin MH, Pohan NA, Garba ZN, Kassim MJ, Rahim AA, Brosse N, et al.
    Int J Biol Macromol, 2016 Jun 30;92:11-19.
    PMID: 27373428 DOI: 10.1016/j.ijbiomac.2016.06.094
    The present study sheds light on the physical and chemical characteristics of microcrystalline cellulose (MCC) isolated from oil palm fronds (OPF) pulps. It was found that the OPF MCC was identified as cellulose II polymorph, with higher crystallinity index than OPF α-cellulose (CrIOPFMCC: 71%>CrIOPFα-cellulose: 47%). This indicates that the acid hydrolysis allows the production of cellulose that is highly crystalline. BET surface area of OPF MCC was found to be higher than OPF α-cellulose (SBETOPFMCC: 5.64m(2)g(-1)>SBETOPFα-cellulose:Qa(0) 2.04m(2)g(-1)), which corroborates their potential as an adsorbent. In batch adsorption studies, it was observed that the experimental data fit well with Langmuir adsorption isotherm in comparison to Freundlich isotherm. The monolayer adsorption capacity (Qa(0)) of OPF MCC was found to be around 51.811mgg(-1) and the experimental data fitted well to pseudo-second-order kinetic model.
    Matched MeSH terms: Cellulose
  17. Electrical resistivity and flexural strength of plastic composites reinforced with pineapple leaf particles
    Shahril Anuar Bahari, Mohd Khairi Yahya, Masitah Abu Kassim, Khairul Safuan Muhammad, Rahimi Baharom
    Scientific Research Journal, 2011;8(2):1-11.
    MyJurnal
    The electrical resistivity and flexural strength of plastic composites reinforced with pineapple leaf particles (PCPLP) is presented. PCPLP were produced using different plastic materials; Polyethylene (PE) and Polypropylene (PP), and different plastic pineapple leaf particle ratios; 50:50 and 70:30. The PCPLP were tested and evaluated with respect to electrical resistivity and flexural strength according to ASTM D257 and D790, respectively. The results indicate that PCPLP made from PP exhibits better electrical resistance than PE, which may be attributed to the better frequency insulation behaviour ofPP. PCPLP using the higher ratio of 70:30 also exhibited better electrical resistance than the lower 50:50 ratio. Cellulose materials inherently influence the electrical resistance of plastic composites, due to their natural propensity to absorb moisture. The PCPLP produced using a ratio of 50:50 for both PP and PE composites exhibited better MOE results than the 70:30 composites, however the converse is true with respect to the MOR. MOE of PCPLP was increased with increasing pineapple leaf particles content due to the greater matrix stiffness of this natural particle with respect to plastic matrix. However, high percentage offiller particles in the matrix (70:30 ratio) has reduced the toughness in the composite structure due to the lost ofphysical contact between high accumulated particles.
    Matched MeSH terms: Cellulose
  18. Fulltext Structural examination and elemental composition analysis of rattan waste fibers for binderless board application
    Zuraida, A., Maisarah, T., Zahurin, H., Muhammad Luqman, A., Roszaliya, A., Wan Shazlin Maisarah, W.M.Y., et al.
    Malaysian Journal of Microscopy, 2015;11(1):39-44.
    MyJurnal
    The chemical composition and anatomical characteristics on lignin distribution of rattan waste were analyzed to determine its suitability to be used in binderless board fabrication. The chemical composition was analyzed by using TAPPI methods. Observation and determination of lignin distribution and board structure were executed by using optical microscopy (OM) and scanning electron microscope (SEM). High amount of hemicellulose, cellulose and lignin content found in rattan waste chemical composition is seen to help in binderless board fabrication. The micrographs revealed that the rattan has fine structural construction that helps in producing good qualities of binderless boards with particular manufacturing parameters.
    Matched MeSH terms: Cellulose
  19. Fulltext Potential of coir fibres as soil reinforcement
    Pvivi Anggraini
    The Pertanika Journal of Scholarly Research Reviews, 2016;2(1):95-106.
    MyJurnal
    This paper presents an evaluation of the alternative use of natural cellulose coir fibres for
    soil reinforcement. Soil reinforcement is defined as a technique to improve the engineering properties
    of soil. Inserting natural fibres into the soil has been proposed as a reinforcement method. Randomly
    distributed coir fibre reinforced soils have recently attracted increasing attention in geotechnical
    engineering due to their strength. Furthermore, there is a need to develop an innovative and
    sustainable pre-treatment method to improve the effectiveness and performance of coir fibre as soil
    reinforcement. The primary purpose of this paper is, therefore, to review the characteristics, benefits,
    applications and weaknesses of coir fibre as soil reinforcement.
    Matched MeSH terms: Cellulose
  20. Recent progress in cellulose nanocrystals: sources and production
    Trache D, Hussin MH, Haafiz MK, Thakur VK
    Nanoscale, 2017 Feb 02;9(5):1763-1786.
    PMID: 28116390 DOI: 10.1039/c6nr09494e
    Cellulose nanocrystals, a class of fascinating bio-based nanoscale materials, have received a tremendous amount of interest both in industry and academia owing to its unique structural features and impressive physicochemical properties such as biocompatibility, biodegradability, renewability, low density, adaptable surface chemistry, optical transparency, and improved mechanical properties. This nanomaterial is a promising candidate for applications in fields such as biomedical, pharmaceuticals, electronics, barrier films, nanocomposites, membranes, supercapacitors, etc. New resources, new extraction procedures, and new treatments are currently under development to satisfy the increasing demand of manufacturing new types of cellulose nanocrystals-based materials on an industrial scale. Therefore, this review addresses the recent progress in the production methodologies of cellulose nanocrystals, covering principal cellulose resources and the main processes used for its isolation. A critical and analytical examination of the shortcomings of various approaches employed so far is made. Additionally, structural organization of cellulose and nomenclature of cellulose nanomaterials have also been discussed for beginners in this field.
    Matched MeSH terms: Cellulose
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links