Thirteen solid waste samples labeled as scales were collected from a storage area of a crude oil production industry and were analysed for radionuclides concentrations. The radium-226 and radium- 228 concentrations were found to be unexpectedly low, i.e. less than 20 Bqkg. However, six samples were found to contain 7 to 2240 Bq/kg 60 Co. Thus, besides naturally occurring radionuclides, there is a possibility to find artificial radionuclides in solid wastes from crude oil production industry.
In this paper, optimum routing was developed based on the travel salesman method and integrated in ArcInfo GIS using linear programming. The results of the optimized travel distances and times for residential waste collection and routing to disposal site were used to calculate the number and type of required track collection, labour requirement, costing of waste collection and to determine the overall solid waste management efficiency through waste management operation research methods. The objective of the study was to optimize residential collection and hauling to disposal site through operation cost minimization for Petaling Jaya Municipality in the state of Selangor, Malaysia. The study determined that with optimized routes and recycling possibilities, the total cost of waste collections could be reduced from RM90,372 to RM20,967, with a reduction of 76.8%. It was also revealed that optimum routes might not necessarily be the shortest distance from point A to point B as travel time maybe high on short distances due to traffic congestion and the presence of many traffic lights. Techniques and methods developed using general GIS have proven effective in route optimization and allowed management of data to suit local conditions and limitations of waste management for the studied area. Thus, scenarios of travel distances, time and waste quantity value generated from the GIS enabled appropriate determination of the number of waste trucks and labour requirements for the operation and the overall calculation of costs of waste management based on the operation research methods used in the study.
In this study a GIS model was developed and spatial analytical techniques performed to identify and select a suitable location for a waste transfer station in the sprawling suburban town of Petaling Jaya. The lack of a transfer station in urban centres of Malaysia has caused many problems and affects the efficiency of waste collection and disposal. With diminishing space for landfills and the increasing cost of solid waste management, the need for urban solid-waste recycling has become very important. However, finding a place for waste to be efficiently sorted before unwanted waste can be carried to disposal landfills has social and physical constraints. This study applies GIS techniques and analysis for site selection and identifies an acceptable area. In the model, environmental, physical and social constraints were taken into account, resulting in the selection of a potential area that is acceptable to the residents of the area because it is out of range of causing public nuisance and within minimum travelling distance for collection vehicles. The results show that the potential location for the transfer station should be in proximity of the industrial area of Petaling Jaya, allowing for the possible sale of recyclable materials to local industries. The location is also sited near a major highway to allow quick transportation of the rest of the unwanted waste to the landfill.
Developing cities like Khulna, the third largest metropolitan city in Bangladesh, have now begun to confess the environmental and public health risks associated with uncontrolled dumping of solid wastes mainly due to the active participation of non-governmental organizations (NGOs) and community-based organizations (CBOs) in municipal solid waste (MSW) management.
Selecting a suitable Multi Criteria Decision Making (MCDM) method is a crucial stage to establish a Solid Waste Management (SWM) system. Main objective of the current study is to demonstrate and evaluate a proposed method using Multiple Criteria Decision Making methods (MCDM). An improved version of Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) applied to obtain the best municipal solid waste management method by comparing and ranking the scenarios. Applying this method in order to rank treatment methods is introduced as one contribution of the study. Besides, Viekriterijumsko Kompromisno Rangiranje (VIKOR) compromise solution method applied for sensitivity analyses. The proposed method can assist urban decision makers in prioritizing and selecting an optimized Municipal Solid Waste (MSW) treatment system. Besides, a logical and systematic scientific method was proposed to guide an appropriate decision-making. A modified TOPSIS methodology as a superior to existing methods for first time was applied for MSW problems. Applying this method in order to rank treatment methods is introduced as one contribution of the study. Next, 11 scenarios of MSW treatment methods are defined and compared environmentally and economically based on the waste management conditions. Results show that integrating a sanitary landfill (18.1%), RDF (3.1%), composting (2%), anaerobic digestion (40.4%), and recycling (36.4%) was an optimized model of integrated waste management. An applied decision-making structure provides the opportunity for optimum decision-making. Therefore, the mix of recycling and anaerobic digestion and a sanitary landfill with Electricity Production (EP) are the preferred options for MSW management.
Globally, around 1.3 billion tonnes of waste are generated annually, and solid waste management has thus become a major concern worldwide. There are projections of a 70% increase in waste generation from 2016 to 2050 owing to urbanization and the rapid growth of the global population. Estimates indicate that around 38,200 tonnes of waste are generated per day in Malaysia, and this volume of waste is significantly shortening the planned life spans of operating sanitary landfills in the country. Batu Pahat is a district in the state of Johor, Malaysia, with a relatively large population of 495,000 and with no record of an operational sanitary landfill. This study was conducted to identify and classify the most suitable sites for sanitary landfill developments in southern Peninsular Malaysia by means of the Analytical Hierarchy Process (AHP), which is recognized as a competent technique for multicriteria decision-making. The resulting landfill site suitability index map established 33.88 km2 of area coverage as very highly suitable for landfill development, while 353.86 km2 of area coverage was classified as unsuitable. Sites 1-6 were identified as the most suitable for landfill activities. Sites 1-5 are situated in agricultural land areas, while site 6 is in a forested land area; this implies public participation and the adoption of compensatory measures in the event of landfill development in these areas, given their socioeconomic importance. The six suitable sites are all at least 2000 m from rivers: 2000-3000 m for sites 1, 3, and 5 and > 3000 m for sites 2, 4, and 6. The six sites are all > 3000 m from fault zones and > 1000 m from flood-prone areas, meaning that occurrences such as fault movements and flooding will have minimal impact on the operational activities of landfills at these sites. The selection of sites 1-6 as very suitable for landfill development was associated with an overall accuracy rating of 93.33% and kappa coefficient score of 0.92 based on accuracy assessment analysis of all sites. This study will guide the actions of policymakers, city planners, and local authorities toward sustainable and environment-friendly landfill development and operation in Batu Pahat and other districts in the state of Johor.
Construction and demolition waste continues to sharply increase in step with the economic growth of less developed countries. Though the construction industry is large, it is composed of small firms with individual waste management practices, often leading to the deleterious environmental outcomes. Quantifying construction and demolition waste generation allows policy makers and stakeholders to understand the true internal and external costs of construction, providing a necessary foundation for waste management planning that may overcome deleterious environmental outcomes and may be both economically and environmentally optimal. This study offers a theoretical method for estimating the construction and demolition project waste generation rate by utilising available data, including waste disposal truck size and number, and waste volume and composition. This method is proposed as a less burdensome and more broadly applicable alternative, in contrast to waste estimation by on-site hand sorting and weighing. The developed method is applied to 11 projects across Malaysia as the case study. This study quantifies waste generation rate and illustrates the construction method in influencing the waste generation rate, estimating that the conventional construction method has a waste generation rate of 9.88 t 100 m(-2), the mixed-construction method has a waste generation rate of 3.29 t 100 m(-2), and demolition projects have a waste generation rate of 104.28 t 100 m(-2).
Matched MeSH terms: Solid Waste/analysis; Solid Waste/statistics & numerical data
Proper implementation of landfill siting with the right regulations and constraints can prevent undesirable long-term effects. Different countries have respective guidelines on criteria for new landfill sites. In this article, we perform a comparative study of municipal solid waste landfill siting criteria stated in the policies and guidelines of eight different constitutional bodies from Malaysia, Australia, India, U.S.A., Europe, China and the Middle East, and the World Bank. Subsequently, a geographic information system (GIS) multi-criteria evaluation model was applied to determine new suitable landfill sites using different criterion parameters using a constraint mapping technique and weighted linear combination. Application of Macro Modeler provided in the GIS-IDRISI Andes software helps in building and executing multi-step models. In addition, the analytic hierarchy process technique was included to determine the criterion weight of the decision maker's preferences as part of the weighted linear combination procedure. The differences in spatial results of suitable sites obtained signifies that dissimilarity in guideline specifications and requirements will have an effect on the decision-making process.
Matched MeSH terms: Solid Waste/analysis; Solid Waste/statistics & numerical data
Most of the developing countries have solid waste management problems. Solid waste strategic planning requires accurate prediction of the quality and quantity of the generated waste. In developing countries, such as Malaysia, the solid waste generation rate is increasing rapidly, due to population growth and new consumption trends that characterize society. This paper proposes an artificial neural network (ANN) approach using feedforward nonlinear autoregressive network with exogenous inputs (NARX) to predict annual solid waste generation in relation to demographic and economic variables like population number, gross domestic product, electricity demand per capita and employment and unemployment numbers. In addition, variable selection procedures are also developed to select a significant explanatory variable. The model evaluation was performed using coefficient of determination (R(2)) and mean square error (MSE). The optimum model that produced the lowest testing MSE (2.46) and the highest R(2) (0.97) had three inputs (gross domestic product, population and employment), eight neurons and one lag in the hidden layer, and used Fletcher-Powell's conjugate gradient as the training algorithm.
Malaysia is one of the developing countries that are facing an increase population
with an increasing and significant generation of waste. Environmental problems may
arise when the solid waste management is improper. The rate of generation is
increasing and the composition is also changing as the nation becomes more
urbanized and industrialized. The objective of this study is to present the data of
municipal solid waste (MSW) generated in Taman Universiti, Skudai, Johor Bahru,
Malaysia. The composition of MSW was studied by segregating it into different
components such as food waste, paper, glass, plastics, metal and tin aluminums. It
was observed that Taman Universiti area produced around 40% plastics waste which
was the highest component compared to other waste, followed by food waste and
papers with 38.2% and 21% respectively. Meanwhile, food waste was recorded the
highest moisture content with 38.2% while glass had the lowest moisture content
with 0.4%. The reliable estimate of MSW generated is important for proper waste
management planning. These data could enhance in implementation of waste
management system in that area.
The use of environmental planning tools for optimum solid waste landfill siting taking into account all environmental implications was carried out by applying Life Cycle Analysis (LCA) to enhance the research information obtained from initial analysis using Geographical Information Systems (GIS). The objective of this study is to identify the most eco-friendly landfill site by conducting a LCA analysis upon 5 potential GIS generated sites which incorporated eleven important criteria related to the social, environmental, and economical factors. The LCA analysis utilized the daily distance covered by collection trucks among the 5 selected landfill sites to generate inventory data on total energy usage for each landfill sites. The planning and selection of the potential sites were facilitated after conducting environmental impact analysis upon the inventory data which showed the least environmental impact.
In Malaysia, the greenhouse gases (GHGs) emissions reduction via composting of source-separated organic waste (SOW) in municipal solid waste (MSW) has not been assessed. Assessment of GHG emissions reduction via composting of SOW is important as environmental impacts from waste management are waste-specific and local-specific. The study presents the case study for potential carbon reduction via composting of SOW in University of Malaya (UM). In this study, a series of calculations were used to evaluate the GHG emission of different SOW management scenarios. The calculations based on IPCC calculation methods (AM0025) include GHGs emissions from landfilling, fuel consumption in transportation and SOW composting activity. The methods were applied to assess the GHG emissions from five alternative SOW management scenarios in UM. From the baseline scenario (S0), a total of 1,636.18 tCO2e was generated. In conjunction with target of 22% recycling rate, as shown in S1, 14% reduction in potential GHG emission can be achieved. The carbon reduction can be further enhanced by increasing the SOW composting capacity. The net GHG emission for S1, S2, S3 and S4 were 1,399.52, 1,161.29, 857.70 and 1,060.48 tCO2e, respectively. In general, waste diversion for composting proved a significant net GHG emission reduction as shown in S3 (47%), S4 (35%) and S2 (29%). Despite the emission due to direct on-site activity, the significant reduction in methane generation at landfill has reduced the net GHG emission. The emission source of each scenario was studied and analysed.
The benefits of using structural lightweight concrete in construction industry, particularly in high rise buildings, over normal weight concrete are numerous. The main method of producing structural lightweight concrete is the use of lightweight aggregates instead of ordinary aggregates in concrete. Due to the limited resources for natural and artificial lightweight aggregates, the alternative sources for lightweight aggregates should be discovered from industrial wastes. Oil palm shell (OPS) and oil-palm-boiler clinker (OPBC) are two solid wastes from palm oil industry and are available in abundance in tropical regimes. The use of just OPS as coarse lightweight aggregate in concrete mixture has some drawbacks for concrete. The aim of this study was to investigate engineering properties of a lightweight concrete containing both of these aggregates. For this purpose, in this study, 50% (by volume) of OPS was replaced with OPBC in an OPS lightweight concrete. The test results showed that when OPS was substituted with OPBC, significant improvement was observed in the compressive, splitting tensile and flexural strengths. In addition, initial and final water absorption as well as drying shrinkage strain of blended coarse lightweight aggregate concrete were significantly less than OPS concrete.
Solid waste collection has been a major challenge for local council Municipal workers in urban areas where the population is growing rapidly and the need for local councils to ensure they provide service to clear solid waste in a timely manner without disrupting the existing system. This case study is a review of awareness of health and safety among municipal workers on solid waste collection. The study is an examination of such awareness in Malaysia which involves the Petaling Jaya City Council in the state of Selangor. We review the operating system of the Petaling Jaya City Council and the risks which are being exposed to the municipal workers in their daily operations. Health and Safety of municipal workers in the areas of public health, safety, and industrial hygiene has been a concern for a long time. In most cases the majority of municipal workers exposed are from the contractual aspect of outsourced labour. It is important to understand how large the area of a solid waste is and to identify, evaluate, and eliminate or control risks and hazards across the operation zone of the municipal workers which involves environmental and occupational demands. The data we find provides the latest perspectives on topics of widespread concern such contractors management, ergonomic safety, confined space, motor vehicle safety, machinery safety, fall hazard safety, electrical safety and emergency response. Management of legal requirements is also discovered to be important to ensure any organization conducting business is not in violation of any law, and if there is a change of process how is this being addressed. Finally, we look at the control measures needed to support a operation on a large scale where it will not endanger the health and safety of municipal workers when they are involved in solid waste management. The recommendation we have based on the review are to ensure there is a holistic approach and systems in place to address all the concerns that will be faced by the local municipal council in their daily operations and responsibilities at every level of the organization. Conclusion: Research material and data related to this area is limited and we hope future holistic research can be conducted to future enhance the study of health and safety effecting the municipal workers. Health and Safety management system and procedures are the key elements in ensuring a successful organization.
Although pharmaceuticals treat illnesses and prevent diseases in humans and animals, ironically, they are now among the emerging pollutants in the environment. As individuals continue to consume medicines, households can become a primary source of pharmaceutical pollutants. This paper explains relevant Malaysian law and policy on the issue. Using a questionnaire survey, it also assesses public perception concerning the environmental impact of pharmaceutical waste and the current methods of disposal that are practiced in Selangor. The survey used a convenience sampling and the data collected were analysed using statistical descriptive analysis. Most of the participants were aware that pharmaceutical waste can have an adverse impact on the environment and public health. Half of the participants disposed of their pharmaceutical waste in trash bins. About 2.9% of the respondents poured their household pharmaceutical waste (HPW) directly down the drain, while 8.8% poured them down the sink in the kitchen or toilet. The study also discovered that while 73.8% of the respondents felt that HPW should be separated from other household solid waste, only 25.2% returned their medicinal waste through the medicine return-back programme. The majority of the respondents (82.5%) agreed that information concerning the proper disposal of HPW is insufficient. The study concludes that while the respondents were aware of the adverse impact of HPW, their practices to ensure proper disposal is discouraging. There is a need for effective unwanted medicines return-back programme as a more prudent disposal method of HPW to avoid any risk to the environment or human health.
Iron and steel industries are among the contributors of CO2 emission in large volume into the atmosphere, causing detrimental effects to the environment and the ecosystem at large scale. These industries also generate solid wastes in the form of electric arc furnace (EAF) slag during operations which result in about 10-15% slag wastes per ton of steel produced. In this study, the EAF slags from an iron and steel-making factory in Klang, Malaysia was utilized for CO2 sequestration through direct aqueous mineral carbonation. According to the surface area analysis, the fresh EAF slag has a mesoporous structure, its elemental composition shows the presence of 20.91 wt.% of CaO that was used for the sequestration of CO2 through carbonation. The sequestration capacity was found to be 58.36 g CO2/kg of slag at ambient temperature in 3 h, with the liquid/solid (L/S) ratio of 5:1 and using <63μm particle size. Moreover, the shrinking core model (SCM) was used to analyze the solid-fluid reaction in a heterogeneous phase and the CO2 sequestration shows to be controlled by the product layer phase. The EAF slag is demonstrated to have the potential of CO2 sequestration at ambient temperature.
It is well known that Asia generates and receives large quantities of plastic waste. Through a detailed study of plastic waste generation and trade, the management and treatment of plastic waste in Asia were analyzed from the regional perspective. The amounts of plastic waste in municipal solid waste and in industrial solid waste were estimated to be 79 Mt and 42 Mt, respectively, in Asia. The overall treatment and recycling status in Asia are unsatisfactory. Asia imported 74% of the plastic waste in the world in 2016, and China (mainland) imported the most plastic waste until 2017, with 5.8 to 8.3 Mt. In 2017, about half the plastic waste imported by Asia came from other regions, and after subtracting the exported quantity, 98% of the plastic waste was left in Asia for treatment and disposal. The plastic waste imported by Asia declined about 72% in monetary value in 2018. There is still a large gap between the plastic waste quantity imported to Asia and that exported from Asia. China's ban of plastic waste imports caused import quantities to drop to 52 kt in 2018, simultaneously, exports from the largest exporting countries or regions such as Hong Kong (China), the USA, Japan, and Germany decreased. While Vietnam, Malaysia and some other Asian countries and regions saw significant increases in plastic waste imports from 2016 to 2018. Considering this situation, countries in Asia are starting to strictly limit plastic waste imports from other countries.
Biogas is an economical and environmentally friendly renewable energy which can be produced by anaerobic digestion (AD). This biochemical method converts organic compounds (mainly from wastes) into a sustainable source of energy. Anaerobic co-digestion (AcoD) is a method combining more than one substrate to resolve the difficulties faced in a single substrate AD system. Solid wastes increases as the population increase so do the urbanization and industrial industries. Food waste and sewage sludge are examples of one of the solid wastes. Co-digesting of both substrates may improve process stabilization to increase biogas production and overcome the nutrients imbalance. Thus, anaerobic co-digestion has been recognized as a technology that could provide a clean renewable energy source and helps reduce the landfill problem. The objective of this paper is to investigate the recent achievements and perspectives on the interaction of co-digestion between food waste and sewage sludge to improve biogas production. This may provide valuable information on the optimization of combinations of substrates: food waste and sewage sludge and prediction of bioreactor performance.
Increasing population, urbanization and industrial activities have increased the amount of solid waste worldwide. Food waste (FW) and sewage sludge (SS) are some of the solid wastes. Co-digesting of both substrates may improve process stabilization to increase biogas production and overcome the nutrients imbalance. Thus, anaerobic co-digestion has been recognized as a technology that could provide a clean renewable energy source and help reducing the landfill problem. In this study, the interaction between FW and SS as co-substrates in anaerobic digestion was studied under mesophilic temperature 36C (± 0.5). The experiments were conducted using five batch reactors with different ratios of substrates. There are four different analyses used to identify the characteristics of FW and SS, which are pH, reducing sugar (RS), total solid (TS), and total carbohydrate (TC). Water displacement method was used to record biogas yield. The experimental results showed that the highest biogas yield was from the composition of 50:50 (FW: SS) with a biogas volume of 1150.14 mL, while the least was the composition of 0:100 (FW: SS) with 170.47 mL biogas produced. The results for substrate degradation showed that the composition of 100:0 (FW: SS) has the highest percentage degradation for reducing sugar with the percentage of 56%, while the minimum was 0:100 (FW: SS) with a percentage of 35%. Besides, for TC, the highest percentage of degradation was the composition 50:50 (FW: SS) with 84%, and the least was 0:100 (FW: SS) with 44%. This study proves that using FW and SS enhanced biogas production as well as reducing the current issues of waste disposal.
Environmental hazards, industrial, and municipal wastes geochemical and geophysical assessments were carried out at an industrial waste disposal (IWD) site at Bukit Kepong, Kuala Lumpur, Malaysia. RES2-D geophysical method was applied, capable of identification and quantification of the industrial wastes; buried hazardous materials (BHM) and their effects on the subsurface stratum, from the moderately saturated zones, to fully saturated zones housing the aquifer units underneath the water table. Six RES2-D survey profiles were respectively acquired along E-W, and N-S directions. The perpendicular arrangement of the RES2-D survey lines, was tenaciously designed to make possible, the industrial waste materials (IWM)and municipal solid waste (MSW) quantification, with sufficient length of survey lines set at 200 m, and electrode spacing of 5 m, to cover as much details segments of the IWM and MSW as possible. The six RES2-D inversion results, helped in the subsurface stratum classification into three layers, namely; soft layers, which encompasses the waste materials, with varied resistivity values i.e., 0-100 Ω-m, at 10-15 m depths. The consolidated layers produced varied resistivity values i.e., 101-400 Ω-m, at 15-20 m depths. The bedrock has the highest resistivity values i.e., 401-2000 Ω-m, at depths > 20 m. The estimated volume of the waste materials was 312,000 m 3, using 3-D Oasis Montaj modeling via rectangular prism model generated from the inverted RES2-D. Results from the geochemical analysis helped in the validation of the site as a potential contaminated zone with severe health effects.