This study was conducted to investigate the potential application of oil palm empty fruit branches (OPEFB) as adsorbents to remove organic methylmercurry, MeHg(II), and inorganic Hg(II) from aqueous solution. The OPEFB was functionalized with amine containing ligand namely 3-ureidopropyltriethoxysilane (UPTES) aiming for better adsorption performance towards both mercury ions. The adsorption was found to be dependent on initial pH, initial concentraton, temperatures, and contact time. The maximum adsorption capacities (Qm.exp) of Hg(II) adsorption onto OPEFB and UPTES-OPEFB were 0.226 and 0.773 mmol/g, respectively. The Qm.exp of MeHg(II) onto OPEFB, however, was higher than UPTES-OPEFB. The adsorption kinetic data obeyed the Elovich model and the adsorption was controlled by the film-diffusion step. The calculated thermodynamic parameters indicate an endothermic adsorption process. Adsorption data analysis indicates that the adsorption mechanism may include ion-exchange, complexation, and physisorption interactions. The potential applications of adsorbents were demonstrated using oilfield produced water and natural gas condensate. The UPTES-OPEFB offered higher selectivity towards both mercury ions than OPEFB. The regenerability studies indicated that the adsorbent could be reused for multiple cycles.
In this study, the optimal conditions for the extraction of antioxidants from the Buah Mahkota Dewa fruit (Phaleria macrocarpa) was determined by using Response Surface Methodology (RSM). The optimisation was applied using a Central Composite Design (CCD) to investigate the effect of three independent variables, namely extraction temperature (°C), extraction time (minutes) and extraction solvent to-feed ratio (% v/v) on four responses: free radical scavenging activity (DPPH), ferric ion reducing power assay (FRAP), total phenolic content (TPC) and total flavonoid content (TFC). The optimal conditions for the antioxidants extraction were found to be 64 °C extraction temperature, 66 min extraction time and 75% v/v solvent to-feed ratio giving the highest percentage yields of DPPH, FRAP, TPC and TFC of 86.85%, 7.47%, 292.86 mg/g and 3.22 mg/g, respectively. Moreover, the data were subjected to Response Surface Methodology (RSM) and the results showed that the polynomial equations for all models were significant, did not show lack of fit, and presented adjusted determination coefficients (R²) above 99%, proving that the yield of phenolic, flavonoid and antioxidants activities obtained experimentally were close to the predicted values and the suitability of the model employed in RSM to optimise the extraction conditions. Hence, in this study, the fruit from P. macrocarpa could be considered to have strong antioxidant ability and can be used in various cosmeceutical or medicinal applications.
As a part of the study to explore the possible strategy for enhancing the shelf life of mango fruits, we investigated the changes in biochemical parameters and activities of ripening associated enzymes of Ashwina hybrid mangoes at 4-day regular intervals during storage at -10°C, 4°C, and 30 ± 1°C. Titratable acidity, vitamin C, starch content, and reducing sugar were higher at unripe state and gradually decreased with the increasing of storage time at all storage temperatures while phenol content, total soluble solid, total sugar, and nonreducing sugar contents gradually increased. The activities of amylase, α-mannosidase, α-glucosidase, and invertase increased sharply within first few days and decreased significantly in the later stage of ripening at 30 ± 1°C. Meanwhile polyphenol oxidase, β-galactosidase, and β-hexosaminidase predominantly increased significantly with the increasing days of storage till later stage of ripening. At -10°C and 4°C, the enzymes as well as carbohydrate contents of storage mango changed slightly up to 4 days and thereafter the enzyme became fully dormant. The results indicated that increase in storage temperature and time correlated with changes in biochemical parameters and activities of glycosidases suggested the suppression of β-galactosidase and β-hexosaminidase might enhance the shelf life of mango fruits.
Fruit pods contain various beneficial compounds that have biological activities and can be used as a source of pharmaceutical and nutraceutical products. Although pods or pericarps are usually discarded when consuming the edible parts of fruits, they contain some compounds that exhibit biological activities after extraction. Most fruit pods included in this review contain polyphenolic components that can promote antioxidant effects on human health. Additionally, anti-inflammatory, antibacterial, antifungal and chemopreventive effects are associated with these fruit pod extracts. Besides polyphenolics, other compounds such as xanthones, carotenoids and saponins also exhibit health effects and can be potential sources of nutraceutical and pharmaceutical components. In this review, information on fruit pods or pericarp of Garcinia mangostana, Ceratonia siliqua, Moringa oleifera, Acacia nilotica, Sapindus rarak and Prosopis cineraria is presented and discussed with regard to their biological activity of the major compounds existing in them. The fruit pods of other ethno- botanical plants have also been reviewed. It can be concluded that although fruit pods are considered as being of no practical use and are often being thrown away, they nevertheless contain compounds that might be useful sources of nutraceutical and other pharmaceutical components.
The purpose of this study was to evaluate the effectiveness of using RNA interference in down regulating the expression of 1-aminocyclopropane-1-carboxylic acid oxidase gene in Eksotika papaya. One-month old embryogenic calli were separately transformed with Agrobacterium strain LBA 4404 harbouring the three different RNAi pOpOff2 constructs bearing the 1-aminocyclopropane-1-carboxylic acid oxidase gene. A total of 176 putative transformed lines were produced from 15,000 calli transformed, selected, then regenerated on medium supplemented with kanamycin. Integration and expression of the targeted gene in putatively transformed lines were verified by PCR and real-time RT-PCR. Confined field evaluation of a total of 31 putative transgenic lines planted showed a knockdown expression of the targeted ACO1 and ACO2 genes in 13 lines, which required more than 8 days to achieve the full yellow colour (Index 6). Fruits harvested from lines pRNAiACO2 L2-9 and pRNAiACO1 L2 exhibited about 20 and 14 days extended post-harvest shelf life to reach Index 6, respectively. The total soluble solids contents of the fruits ranged from 11 to 14° Brix, a range similar to fruits from non-transformed, wild type seed-derived plants.
Among palm oil millers, the ripeness of oil palm Fresh Fruit Bunch (FFB) is determined through visual inspection. To increase the productivity of the millers, many researchers have proposed with a new detection method to replace the conventional one. The sensitivity of such a sensor plays a crucial role in determining the effectiveness of the method. In our preliminary study a novel oil palm fruit sensor to detect the maturity of oil palm fruit bunches is proposed. The design of the proposed air coil sensor based on an inductive sensor is further investigated to improve its sensitivity. This paper investigates the results pertaining to the effects of the air coil structure of an oil palm fruit sensor, taking consideration of the used copper wire diameter ranging from 0.10 mm to 0.18 mm with 60 turns. The flat-type shape of air coil was used on twenty samples of fruitlets from two categories, namely ripe and unripe. Samples are tested with frequencies ranging from 20 Hz to 120 MHz. The sensitivity of the sensor between air to fruitlet samples increases as the coil diameter increases. As for the sensitivity differences between ripe and unripe samples, the 5 mm air coil length with the 0.12 mm coil diameter provides the highest percentage difference between samples and it is amongst the highest deviation value between samples. The result from this study is important to improve the sensitivity of the inductive oil palm fruit sensor mainly with regards to the design of the air coil structure. The efficiency of the sensor to determine the maturity of the oil palm FFB and the ripening process of the fruitlet could further be enhanced.
The present study was conducted to examine the effects of sonication treatments (time intervals of 0, 15, 30, 45 and 60 min.) on phenolics and other antioxidant compounds in starfruits extracted in methanol and water. Overall, methanolic extracts exhibited significantly higher extractability, percentage inhibition of DPPH radicals, ferric reducing antioxidant property (FRAP) value, antioxidant capacity, flavonoids, total phenolics and tannins (p
Developmental biochemical information is a vital base for the elucidation of seed physiology and metabolism. However, no data regarding the biochemical profile of oil palm (Elaeis guineensis Jacq.) seed development has been reported thus far. In this study, the biochemical changes in the developing oil palm seed were investigated to study their developmental pattern. The biochemical composition found in the seed differed significantly among the developmental stages. During early seed development, the water, hexose (glucose and fructose), calcium and manganese contents were present in significantly high levels compared to the late developmental stage. Remarkable changes in the biochemical composition were observed at 10 weeks after anthesis (WAA): the dry weight and sucrose content increased significantly, whereas the water content and hexose content declined. The switch from a high to low hexose/sucrose ratio could be used to identify the onset of the maturation phase. At the late stage, dramatic water loss occurred, whereas the content of storage reserves increased progressively. Lauric acid was the most abundant fatty acid found in oil palm seed starting from 10 WAA.
Oil palm is one of the most productive oil producing crops and can store up to 90% oil in its fruit mesocarp. However, the biosynthetic regulation and drivers of palm mesocarp development are still not well understood. Multiplatform metabolomics technology was used to profile palm metabolites during six critical stages of fruit development in order to better understand lipid biosynthesis. Significantly higher amino acid levels were observed in palm mesocarp preceding lipid biosynthesis. Nucleosides were found to be in high concentration during lipid biosynthesis, whereas levels of metabolites involved in the tricarboxylic acid cycle were more concentrated during early fruit development. Apart from insights into the regulation of metabolites during fruit development in oil palm, these results provide potentially useful metabolite yield markers and genes of interest for use in breeding programs.
Postharvest treatments of fruits using techniques such as ultraviolet-C have been linked with maintenance of the fruit quality as well as shelf-life extension. However, the effects of this treatment on the quality of fruits on a proteomic level remain unclear. This study was conducted in order to understand the response of mango fruit to postharvest UV-C irradiation.
Volvariella volvacea (Family: Plutaceae), also more commonly known as paddy straw mushroom, is an edible mushroom with high nutritional content. It is usually cultivated using lignocellulosic-based materials for enhanced production. However, V. volvacea is highly perishable and easily deteriorates in terms of quality and appearance after harvest. The present paper thus aimed to provide a critical review on aspects related to the production of V. volvacea using palm oil empty fruit bunch as cultivation substrate. The different stages of V. volvacea development are also highlighted. The present review also provides some information on the preservation techniques and appropriate postharvest management in extending V. volvacea shelf life to further boost the paddy straw mushroom industry
The drying of fruits and vegetables is a complex operation that demands much energy and time. In practice, the drying of fruits and vegetables increases product shelf-life and reduces the bulk and weight of the product, thus simplifying transport. Occasionally, drying may lead to a great decrease in the volume of the product, leading to a decrease in storage space requirements. Studies have shown that dependence purely on experimental drying practices, without mathematical considerations of the drying kinetics, can significantly affect the efficiency of dryers, increase the cost of production, and reduce the quality of the dried product. Thus, the use of mathematical models in estimating the drying kinetics, the behavior, and the energy needed in the drying of agricultural and food products becomes indispensable. This paper presents a comprehensive review of modeling thin-layer drying of fruits and vegetables with particular focus on thin-layer theories, models, and applications since the year 2005. The thin-layer drying behavior of fruits and vegetables is also highlighted. The most frequently used of the newly developed mathematical models for thin-layer drying of fruits and vegetables in the last 10 years are shown. Subsequently, the equations and various conditions used in the estimation of the effective moisture diffusivity, shrinkage effects, and minimum energy requirement are displayed. The authors hope that this review will be of use for future research in terms of modeling, analysis, design, and the optimization of the drying process of fruits and vegetables.
The spatial dissemination of three prevalent taxa of sooty blotch and flyspeck (SBFS) fungi under several levels of precipitation was compared during 2015 and 2016 in an Iowa apple orchard. Overhead irrigation was used to supplement ambient precipitation in order to insure SBFS spore dissemination and colony development. There were five irrigation levels, involving 1-min-long periods of irrigation that were imposed either once or twice per hour at intervals of 3, 6, or 12 h, as well as a nonirrigated control. Preselected apple fruit were inoculated with one of the three SBFS taxa to serve as sources of inoculum. Dissemination from these inoculated apple fruit was assessed at harvest by counting SBFS colonies on water-sprayed and nontreated fruit. As a further control, additional fruit were enclosed in fruit bags throughout the fruit development period. In both 2015 and 2016, the number of colonies of the SBFS fungus Peltaster gemmifer per apple increased sharply as the duration of irrigation increased, whereas the number of colonies of Microcyclosporella mali increased to a lesser extent and Stomiopeltis sp. RS1 showed no increase. In 2015, the linear relationship between the duration of irrigation-imposed precipitation levels and the number of colonies on the water-sprayed apple fruit was similar for P. gemmifer (slope = 0.09), Stomiopeltis sp. RS1 (slope = 0.07), and Microcyclosporella mali (slope = 0.13); whereas, in 2016, the slope was higher for P. gemmifer (0.28) than for Stomiopeltis sp. RS1 (-0.09) or M. mali (0.06). The results indicated that dissemination of P. gemmifer increased sharply in response to increased irrigation-imposed precipitation, and that dissemination patterns differed considerably among the three SBFS taxa. The apparent advantage of P. gemmifer in precipitation-triggered dissemination may stem from its ability to produce spores rapidly by budding. To our knowledge, this is the first article to assess splash dispersal by SBFS fungi in the field and the first to document taxon-specific patterns of dissemination in this pathogen complex.
Oil palm is one of the key industries highly observed in Malaysia, due to its high demand both whether locally or internationally. The oil extraction rate (OER) in palm oil production is used as an element to identify the performance of the mills, estates and producers. In view of this, there are specific instrument or sensor needs to be implemented at the mills especially during the reception of fresh fruit bunches (FFB) transported from the field for oil content processing. This paper aims to study and propose the use of a fruit battery-based oil palm maturity sensor to analyse the effect of the sensor to various parameters. The study utilizes a charging method with different parameters, including a moisture content test on the palm oil samples. Three types of parameters are tested along with the different grades of oil palm fruit from different bunches, such as the load resistance, charging voltage and charging time. The repeatability data of the samples are obtained with the used list of values in each parameter. The results show that the parameters tested for the unripe, under ripe and ripe samples can affect the sensor sensitivity.
Cellulose nanocrystals (CNC) have received great research attention since the last few decades due to their extraordinary properties and wide range of applications. In this study, a sustainable and cost-effective method for the synthesis of lignin-containing cellulose nanocrystals (LCNC) from oil palm empty fruit bunch (EFB) is presented. This method is able to retain the lignin in EFB and manifest the properties of lignin. The proposed synthesis process is simpler than the conventional method of producing lignin-coated CNC by first removing the lignin to synthesize CNC followed by the re-coating of lignin on the structure. The samples of LCNC were characterized by transmission electron microscopy, X-ray diffraction, Fourier-transform infrared spectroscopy and water contact angle analysis. In addition, by altering the acid concentration during acid hydrolysis process (53% - 60% H2SO4), both surface hydrophobicity (66.0° - 75.1°) and length of LCNC (467 nm-177 nm) can be altered wherein a higher concentration of acid resulted in a greater contact angle and a shorter length of LCNC. Cost and energy analysis deduced that the proposed synthesis method saved about 62% of the total material cost and 80% less energy as compared to the synthesis of lignin-coated CNC.
Changes in physicochemical properties of moisture, ash, and fat contents, and color, due to freeze and oven post-drying treatments on flavedo, albedo, and lamella pomelo fruit peels were investigated. Physicochemical properties influence consumer acceptability and only a few studies are known. Pomelo peels were subjected to freeze drying and conventional drying at 60°C. Fresh pomelo peel was used as a control. Post-drying treatment changes in moisture, ash, and fat contents were observed, compared to controls. Minimal color changes were observed for freeze drying, compared with oven drying for flavedo, albedo, and lamella. Useful information for evaluation of drying treatments that can be used on pomelo peels is provided.
Chinese bayberry fruit were treated with hot air (HA) at 48 ℃ for 3 h and then stored at 4 ℃ for 15 d. Changes in fungal communities were analyzed by high-throughput sequencing (HTS), and decay and fruit quality were monitored during storage. The results showed that HA treatment effectively maintains fruit quality and the richness and diversity of fungal communities. Heat treatment inhibited decay development and reduced the growth of fungi in the genera Botryotinia spp., Davidiella spp., Hanseniaspora spp., and Candida spp. Canonical correspondence analysis further revealed that Botryotinia spp. and Davidiella spp. were positively correlated with fruit decay and weight loss. FUNGuild analysis demonstrated that HA-treated bayberries had a lower relative abundance within the plant pathogen guild, but higher relative abundance within the endophyte guild. The results suggest that HA treatment reduces pathogens by favoring the increase of endophytes, providing new insight into the decay development and quality changes during the storage of postharvest Chinese bayberries.
The fruit and leaf of God's crown (Phaleria macrocarpa) have been traditionally used to treat a wide variety of diseases. However, the proteins of this tropical plant are still heavily understudied. Three protein extraction methods; phenol (Phe), trichloroacetic acid (TCA)-acetone-phenol (TCA-A-Phe), and ultrasonic (Ult) were compared on the fruit and leaf of P. macrocarpa. The Phe extraction method showed the highest percentage of recovered protein after the resolubilization process for both leaf (12.24%) and fruit (30.41%) based on protein yields of the leaf (6.15 mg/g) and fruit (36.98 mg/g). Phe and TCA-A-Phe extraction methods gave well-resolved bands over a wide range of molecular weights through sodium dodecyl sulfate-polyacrylamide gel electrophoresis. Following liquid chromatography-tandem mass spectrometry analysis, proteins identified through the Phe extraction method were 30%-35% enzymatic proteins, including oxidoreductases, transferases, hydrolases, lyases, isomerases, and ligases that possess various biological functions. PRACTICAL APPLICATIONS: Every part of God's crown plant is traditionally consumed to treat various illnesses. While plant's benefits are well known and have led to a plethora of health products, the proteome remains mostly unknown. This study compares three protein extraction methods for the leaf and fruit of P. macrocarpa and identifies their proteins thru LC-MS/MS coupled with PEAKS. These method comparisons can be a guide for works on other plants as well. In addition, the proteomics data from this study may shed light on the functional properties of these plant parts and their products.
The antioxidant properties of skin, flesh and kernel of Canarium odontophyllum fruit were determined. The methanolic extracts of the fruit were screened for their total phenolic content and antioxidant properties. The averaged antioxidant properties (mM TE/g FM) in skin, flesh, and kernel of Canarium odontophyllum were 16.46 ± 0.24, 20.54 ± 0.35, and 8.89 ± 0.29, respectively by DPPH assay; 151.24 ± 9.75, 70.58 ± 2.98, and 5.65 ± 0.02, respectively by FRAP assay; and 47.9 ± 0.00, 11.61 ± 1.14, and 3.00 ± 0.00, respectively by β-Carotene bleaching method. The averaged OH scavenging activity (mg DMSOE/mg FM) in skin, flesh, and kernel of Canarium odontophyllum were 43.33 ± 13.85, 7.81 ± 1.42, and 3.31 ± 0.80, respectively. While averaged total phenolic content (mg GAE/100g FM) were 387.5 ± 33.23, 267.0 ± 4.24, and 51.0 ± 0.00 for skin, flesh, and kernel respectively. Antioxidant activities were positively correlated with the total phenolic content (0.71 ≤ r ≤ 0.84).
Non-destructive and real time method becomes a well-liked method to researchers in the oil palm
industry since 2000. This method has the ability to detect oil content in order to increase the
production of oil palm for better profit. Hence, this research investigates the potential of neutron
source to estimate oil content in palm oil fruit since oil palm contains hydrogen with chemical
formula C55H96O6. For this paper, oil palm loose fruit was being used and divided into three
groups. These three groups are ripe, under-ripe and bruised fruit. A total of 21 loose fruit for each
group were collected from a private plantation in Malaysia. Each sample was scanned using
neutron backscattered technique. The higher neutron count, the more hydrogen content, and the
more oil content in palm oil fruit. The best correlation result came from the ripe fruits with r2=0.98.
This research proves that neutron backscattered technique can be used as a non-destructive and
real time grading system for palm oil.