Displaying publications 101 - 120 of 288 in total

Abstract:
Sort:
  1. Enhancement of C-phycocyanin purity using negative chromatography with chitosan-modified nanofiber membrane
    Ng IS, Tang MSY, Show PL, Chiou ZM, Tsai JC, Chang YK
    Int J Biol Macromol, 2019 Jul 01;132:615-628.
    PMID: 30940588 DOI: 10.1016/j.ijbiomac.2019.03.235
    In this work, a chitosan-modified nanofiber membrane was fabricated and used to examine the permeation characteristics of C-phycocyanin (CPC) obtained from Spirulina platensis. The effects of NaCl concentration (0.1-1.0 M), chitosan coupling pH (6-8), chitosan coupling concentration (0.1-3.0%), algal solution pH (6-8), algal mass concentration (0.1-1.0% dw/v), and membrane flux (4.08 × 10-2-2.04 × 10-1 mL/min·cm2) on the penetration performance of the membrane for CPC were investigated. The results show that the order of binding selectivity of the membrane for these proteins is contaminating proteins (TP) > allophycocyanin (APC) > CPC. TP and APC molecules were more easily adsorbed by the chitosan-modified membrane, and the CPC molecules most easily penetrated the membrane without being adsorbed, enhancing CPC purity. The purification factor and total mass flux were 3.3 fold and 66%, respectively, in a single step.
    Matched MeSH terms: Sodium Chloride
  2. Fulltext Statistical Design of Experimental and Bootstrap Neural Network Modelling Approach for Thermoseparating Aqueous Two-Phase Extraction of Polyhydroxyalkanoates
    Leong YK, Chang CK, Arumugasamy SK, Lan JC, Loh HS, Muhammad D, et al.
    Polymers (Basel), 2018 Jan 30;10(2).
    PMID: 30966168 DOI: 10.3390/polym10020132
    At present, polyhydroxyalkanoates (PHAs) have been considered as a promising alternative to conventional plastics due to their diverse variability in structure and rapid biodegradation. To ensure cost competitiveness in the market, thermoseparating aqueous two-phase extraction (ATPE) with the advantages of being mild and environmental-friendly was suggested as the primary isolation and purification tool for PHAs. Utilizing two-level full factorial design, this work studied the influence and interaction between four independent variables on the partitioning behavior of PHAs. Based on the experimental results, feed forward neural network (FFNN) was used to develop an empirical model of PHAs based on the ATPE thermoseparating input-output parameter. In this case, bootstrap resampling technique was used to generate more data. At the conditions of 15 wt % phosphate salt, 18 wt % ethylene oxide⁻propylene oxide (EOPO), and pH 10 without the addition of NaCl, the purification and recovery of PHAs achieved a highest yield of 93.9%. Overall, the statistical analysis demonstrated that the phosphate concentration and thermoseparating polymer concentration were the most significant parameters due to their individual influence and synergistic interaction between them on all the response variables. The final results of the FFNN model showed the ability of the model to seamlessly generalize the relationship between the input⁻output of the process.
    Matched MeSH terms: Sodium Chloride
  3. Fulltext Synthesis, Characterization and the Solvent Effects on Interfacial Phenomena of Jatropha Curcas Oil Based Non-Isocyanate Polyurethane
    Haniffa MACM, Ching YC, Chuah CH, Kuan YC, Liu DS, Liou NS
    Polymers (Basel), 2017 May 01;9(5).
    PMID: 30970841 DOI: 10.3390/polym9050162
    Non-isocyanate polyurethane (NIPU) was prepared from Jatropha curcas oil (JCO) and its alkyd resin via curing with different diamines. The isocyanate-free approach is a green chemistry route, wherein carbon dioxide conversion plays a major role in NIPU preparation. Catalytic carbon dioxide fixation can be achieved through carbonation of epoxidized derivatives of JCO. In this study, 1,3-diaminopropane (DM) and isophorone diamine (IPDA) were used as curing agents separately. Cyclic carbonate conversion was catalyzed by tetrabutylammonium bromide. After epoxy conversion, carbonated JCO (CJCO) and carbonated alkyd resin (CC-AR) with carbonate contents of 24.9 and 20.2 wt %, respectively, were obtained. The molecular weight of CJCO and CC-AR were determined by gel permeation chromatography. JCO carbonates were cured with different amine contents. CJCO was blended with different weight ratios of CC-AR to improve its characteristics. The cured NIPU film was characterized by spectroscopic techniques, differential scanning calorimetry, and a universal testing machine. Field emission scanning electron microscopy was used to analyze the morphology of the NIPU film before and after solvent treatment. The solvent effects on the NIPU film interfacial surface were investigated with water, 30% ethanol, methyl ethyl ketone, 10% HCl, 10% NaCl, and 5% NaOH. NIPU based on CCJO and CC-AR (ratio of 1:3) with IPDA crosslink exhibits high glass transition temperature (44 °C), better solvent and chemical resistance, and Young's modulus (680 MPa) compared with the blend crosslinked with DM. Thus, this study showed that the presence of CC-AR in CJCO-based NIPU can improve the thermomechanical and chemical resistance performance of the NIPU film via a green technology approach.
    Matched MeSH terms: Sodium Chloride
  4. Fulltext Novel Functionalized Polythiophene-Coated Fe₃O₄ Nanoparticles for Magnetic Solid-Phase Extraction of Phthalates
    Baharin SNA, Muhamad Sarih N, Mohamad S
    Polymers (Basel), 2016 Apr 28;8(5).
    PMID: 30979266 DOI: 10.3390/polym8050117
    Poly(phenyl-(4-(6-thiophen-3-yl-hexyloxy)-benzylidene)-amine) (P3TArH) was successfully synthesized and coated on the surface of Fe₃O₄ magnetic nanoparticles (MNPs). The nanocomposites were characterized by Fourier transform infra-red (FTIR), X-ray diffractometry (XRD), Brunauer-Emmett-Teller (BET) surface area analysis, analyzer transmission electron microscopy (TEM) and vibrating sample magnetometry (VSM). P3TArH-coated MNPs (MNP@P3TArH) showed higher capabilities for the extraction of commonly-used phthalates and were optimized for the magnetic-solid phase extraction (MSPE) of environmental samples. Separation and determination of the extracted phthalates, namely dimethyl phthalate (DMP), diethyl phthalate (DEP), dipropyl phthalate (DPP), dibutyl phthalate (DBP), butyl benzyl phthalate (BBP), dicyclohexyl phthalate (DCP), di-ethylhexyl phthalate (DEHP) and di-n-octyl phthalate (DNOP), were conducted by a gas chromatography-flame ionization detector (GC-FID). The best working conditions were as follows; sample at pH 7, 30 min extraction time, ethyl acetate as the elution solvent, 500-µL elution solvent volumes, 10 min desorption time, 10-mg adsorbent dosage, 20-mL sample loading volume and 15 g·L-1 concentration of NaCl. Under the optimized conditions, the analytical performances were determined with a linear range of 0.1⁻50 µg·L-1 and a limit of detection at 0.08⁻0.468 µg·L-1 for all of the analytes studied. The intra-day (n = 7) and inter-day (n = 3) relative standard deviations (RSD%) of three replicates were each demonstrated in the range of 3.7⁻4.9 and 3.0⁻5.0, respectively. The steadiness and reusability studies suggested that the MNP@P3TArH could be used up to five cycles. The proposed method was executed for the analysis of real water samples, namely commercial bottled mineral water and bottled fresh milk, whereby recoveries in the range of 68%⁻101% and RSD% lower than 7.7 were attained.
    Matched MeSH terms: Sodium Chloride
  5. Fulltext Combination effect of argan oil and low frequency electromagnetic field on open wound in mice
    Siti F. Masre, Muzamir, M.K, Sabarina, I., Jehan, N., Yanti Rosli
    Jurnal Sains Kesihatan Malaysia, 2018;16(101):41-45.
    MyJurnal
    This study was conducted to evaluate the effect of argan oil with the exposure of low frequency electromagnetic field (EMF) on open wound healing in mice. Eighteen male mice (20-40 g) were divided into three groups: phosphate buffer saline (PBS) as negative control, solcoseryl gel as positive control, and argan oil with the exposure of low frequency EMF, 1.2 mT (treatment group). Full thickness wounds (4 mm diameter) were induced on the shaved dorsal of the mouse. All mice were sacrificed on day 12 after the final treatment. Macroscopic observation, wound contraction rate, histopathology analysis and total protein content were examined in this study. Results showed that wounds treated with argan oil and exposed to low frequency EMF has a significant increase in wound contraction rate (p < 0.05) and total protein content (p < 0.05). Moreover, histopathological analysis on the wound tissues displayed complete re-epithelization with thick and dense collagen fibers in the argan oil with low frequency EMF exposure treated group. In conclusion, topical treatment of argan oil with low frequency EMF exposure yield a better healing progress and showed the ability to accelerate wound healing
    Matched MeSH terms: Sodium Chloride
  6. Fulltext Microfluidics Chip for Directional Solvent Extraction Desalination of Seawater
    Abdulbari HA, Basheer EAM
    Sci Rep, 2019 08 29;9(1):12576.
    PMID: 31467344 DOI: 10.1038/s41598-019-49071-7
    Directional solvent extraction is one of the promising membrane-less seawater desalination method. This technique was not extensively investigated due the poor mixing and separation performances of its bench-scale system. It is believed that, overcoming these drawbacks is possible now with the rapid development of microfluidics technology that enabled high-precession micro mixing and separation. This work presents microfluidics chip for extracting and separating salt from seawater. The chip was designed with two sections for extraction and separation. In both sections, the liquids were separated using capillary channels perpendicular to the main stream. The main channels were designed to be 400 µm in width and 100 µm in height. Two streams inlets were introduced through a Y-junction containing octanoic acid as the organic phase and saltwater as the aqueous phase. The desalination performance was investigated at four different temperatures and five different solvent flow rates. Water product salinity was recorded to be as low as 0.056% (w/w) at 60 °C and 40 mL/h. A maximum water yield of 5.2% was achieved at 65 °C and 40 mL/h with a very low solvent residual (70 ppm). The chip mass transfer efficiency was recorded to be as high as 68% under similar conditions. The fabricated microfluidic desalination system showed a significant improvement in terms of water yield and separation efficiency over the conventional macroscale. The high performance of this microsystem resulted from its ability to achieve a high mixing efficiency and separate phases selectively and that will provide a good platform in the near future to develop small desalination kits for personal use.
    Matched MeSH terms: Sodium Chloride
  7. Voltammetric determination of iodide in iodized table salt using cetyltrimethylammonium bromide as ion-pairing
    Jamilan MA, Abdullah J, Alang Ahmad SA, Md Noh MF
    J Food Sci Technol, 2019 Aug;56(8):3846-3853.
    PMID: 31413410 DOI: 10.1007/s13197-019-03855-x
    In this work, voltammetric study based on cetyltrimethylammonium bromide (CTAB) as an ion-pairing agent for the determination of iodine level in iodized table salt has been explored. CTAB was used as an intermediate compound between iodide (I-) and the electrode due to its ability to dissociate to produce cetyltrimethylammonium ions ([CTA]+). The [CTA]+ with a long hydrophobic alkyl chain can be directly adsorbed onto the surface of the working electrode, and this in turns coated the electrode with cationic charge and enhance the electrode ability to bind to iodide (I-) and other molecular iodine ions. A mixture of iodide and CTAB ([CTA]+I-) was prepared and potential of 1.0 V for 60.0 s was applied to pre-concentrate the solution on the working electrode causing the [CTA]+I- to oxidize to iodine (I2). The produced I2 immediately react with chloride ion (Cl-) from the electrolyte of hydrochloric acid (HCl) to produce I2Cl- and form ion-pair with CTA+ as [CTA]+I2Cl-. The linear calibration curve of the developed method towards iodide was in the concentration range of 0.5-4.0 mg/L with sensitivity of - 1.383 µA mg/L-1 cm-2 (R2 = 0.9950), limit of detection (LOD) of 0.3 mg/L and limit of quantification (LOQ) of 1.0 mg/L, respectively. The proposed method indicates good agreement with the standard method for iodine determination with recovery range from 95.0 to 104.3%. The developed method provided potential application as a portable on-site iodine detector.
    Matched MeSH terms: Sodium Chloride, Dietary
  8. In Vitro Evaluation of Potential Probiotic Strain Lactococcus lactis Gh1 and Its Bacteriocin-Like Inhibitory Substances for Potential Use in the Food Industry
    Jawan R, Abbasiliasi S, Mustafa S, Kapri MR, Halim M, Ariff AB
    Probiotics Antimicrob Proteins, 2021 04;13(2):422-440.
    PMID: 32728855 DOI: 10.1007/s12602-020-09690-3
    Determination of a microbial strain for the joining into sustenance items requires both in vitro and in vivo assessment. A newly isolated bacteriocin-like inhibitory substance (BLIS) producing lactic acid bacterium, Lactococcus lactis Gh1, was isolated from a traditional flavour enhancer and evaluated in vitro for its potential applications in the food industry. Results from this study showed that L. lactis was tolerant to NaCl (≤ 4.0%, w/v), phenol (≤ 0.4%, w/v), 0.3% (w/v) bile salt, and pH 3. BLIS from L. lactis showed antimicrobial activity against Listeria monocytogenes ATCC 15313 and was susceptible to 10 types of antibiotics. The absence of haemolytic activity and the presence of acid phosphatase and naphthol-AS-BI-phosphohydrolase were observed in L. lactis. L. lactis could coagulate milk and showed a negative response to amylolytic and proteolytic activities and did not secrete β-galactosidase. The antimicrobial activity of BLIS was completely abolished at 121 °C. The BLIS was conserved at 4 °C in BHI and MRS medium up to 6-4 months, respectively. BLIS activity was more stable in BHI as compared to MRS after four freeze-thaw cycles and was not affected by a wide range of pH (pH 4-8). BLIS was sensitive to proteinase k and resistant to catalase and trypsin. The antimicrobial activity was slightly reduced by acetone, ethanol, methanol, and acetonitrile at 10% (v/v) and also towards Tween-80, urea, and NaCl 1% (v/v). Results from this study have demonstrated that L. lactis has a vast potential to be applied in the food industry, such as for the preparation of starter culture, functional foods, and probiotic products.
    Matched MeSH terms: Sodium Chloride
  9. Fulltext CD89/CD35 Expression Ratio in Salivary Neutrophil as an Early Detection Marker for Severe Early Childhood Caries
    Luthfi M, Oki AS, Indrawati R, Rifai M, Dachlan YP, Razak FA
    Eur J Dent, 2020 Jul;14(3):386-392.
    PMID: 32645730 DOI: 10.1055/s-0040-1713704
    OBJECTIVES:  To analyze CD35/CD89 expression ratio on the surface of neutrophils as an early detection marker for S-ECC.

    MATERIALS AND METHODS:  Saliva was collected from 4- to 6-year-old kindergarten students. Salivary neutrophils were obtained by instructing the subjects to rinse their mouth with 1 mL of sterile 1.5% NaCl for 30 seconds before expectorating it into a sterile glass. The expression of CFSE+CD35+ and CFSE+CD89+was measured and analyzed using flow cytometry.

    RESULTS: The expression of CFSE+CD89+ in the caries-free group (2.46 ± 0.39) was significantly lower than that in the S-ECC group (3.41 ± 1.11), with a p-value of 0.0001, while the expression of CFSE+CD35+ in the caries-free group was (2.35 ± 0.56) compared with (1.54 ± 0.35) (p = 0.0001) in the S-ECC group.

    CONCLUSIONS:  The expression ratio of CFSE+CD89+ and CFSE+CD35+constitutes a marker for S-ECC.

    Matched MeSH terms: Sodium Chloride
  10. Fulltext Reaction Mechanism of Wollastonite In Situ Mineral Carbonation for CO2 Sequestration: Effects of Saline Conditions, Temperature, and Pressure
    Kashim MZ, Tsegab H, Rahmani O, Abu Bakar ZA, Aminpour SM
    ACS Omega, 2020 Nov 17;5(45):28942-28954.
    PMID: 33225124 DOI: 10.1021/acsomega.0c02358
    The research presented here investigates the reaction mechanism of wollastonite in situ mineral carbonation for carbon dioxide (CO2) sequestration. Because wollastonite contains high calcium (Ca) content, it was considered as a suitable feedstock in the mineral carbonation process. To evaluate the reaction mechanism of wollastonite for geological CO2 sequestration (GCS), a series of carbonation experiments were performed at a range of temperatures from 35 to 90 °C, pressures from 1500 to 4000 psi, and salinities from 0 to 90,000 mg/L NaCl. The kinetics batch modeling results were validated with carbonation experiments at the specific pressure and temperature of 1500 psi and 65 °C, respectively. The results showed that the dissolution of calcium increases with increment in pressure and salinity from 1500 to 4000 psi and 0 to 90000 mg/L NaCl, respectively. However, the calcium concentration decreases by 49%, as the reaction temperature increases from 35 to 90 °C. Besides, it is clear from the findings that the carbonation efficiency only shows a small difference (i.e., ±2%) for changing the pressure and salinity, whereas the carbonation efficiency was shown to be enhanced by 62% with increment in the reaction temperature. These findings can provide information about CO2 mineralization of calcium silicate at the GCS condition, which may enable us to predict the fate of the injected CO2, and its subsurface geochemical evolution during the CO2-fluid-rock interaction.
    Matched MeSH terms: Sodium Chloride
  11. Fulltext Recovery of a Bacteriocin-Like Inhibitory Substance from Lactobacillus bulgaricus FTDC 1211 Using Polyethylene-Glycol Impregnated Amberlite XAD-4 Resins System
    Abdul Aziz NFH, Abbasiliasi S, Ng ZJ, Abu Zarin M, Oslan SN, Tan JS, et al.
    Molecules, 2020 Nov 16;25(22).
    PMID: 33207534 DOI: 10.3390/molecules25225332
    Lactobacillus bulgaricus is a LAB strain which is capable of producing bacteriocin substances to inhibit Staphylococcus aureus. The aim of this study was to purify a bacteriocin-like inhibitory substance (BLIS) produced by L. bulgaricus FTDC 1211 using an aqueous impregnated resins system consisting of polyethylene-glycol (PEG) impregnated on Amberlite XAD4. Important parameters influencing on purification of BLIS, such as the molecular weight and concentration of PEG, the concentration and pH of sodium citrate and the concentration of sodium chloride, were optimized using a response surface methodology. Under optimum conditions of 11% (w/w) of PEG 4000 impregnated Amberlite XAD4 resins and 2% (w/w) of sodium citrate at pH 6, the maximum purification factor (3.26) and recovery yield (82.69% ± 0.06) were obtained. These results demonstrate that AIRS could be used as an alternate purification system in the primary recovery step.
    Matched MeSH terms: Sodium Chloride
  12. α-Sulfo alkyl ester surfactants: Impact of changing the alkyl chain length on the adsorption, mixing properties and response to electrolytes of the tetradecanoate
    Wang Z, Li P, Ma K, Chen Y, Yan Z, Penfold J, et al.
    J Colloid Interface Sci, 2021 Mar 15;586:876-890.
    PMID: 33309145 DOI: 10.1016/j.jcis.2020.10.122
    HYPOTHESIS: The α-sulfo alkyl ester, AES, surfactants are a class of anionic surfactants which have potential for improved sustainable performance in a range of applications, and an important feature is their enhanced tolerance to precipitation in the presence of multivalent counterions. It is proposed that their adsorption properties can be adjusted substantially by changing the length of the shorter alkyl chain, that of the alkanol group in the ester.

    EXPERIMENTS: Surface tension and neutron reflectivity have been used to investigate the variation in the adsorption properties with the shorter alkyl chain length (methyl, ethyl and propyl), the impact of NaCl on the adsorption, the tendency to form surface multilayer structures in the presence of AlCl3, and the effects of mixing the methyl ester sulfonate with the ethyl and propyl ester sulfonates on the adsorption.

    FINDINGS: The variations in the critical micelle concentration, CMC, the adsorption isotherms, the saturation adsorption values, and the impact of NaCl illustrate the subtle influence of varying the shorter alkyl chain length of the surfactant. The non-ideal mixing of pairs of AES surfactants with different alkanol group lengths of the ester show that the extent of the non-ideality changes as the difference in the alkanol length increases. The surface multilayer formation observed in the presence of AlCl3 varies in a complex manner with the length of the short chain and for mixtures of surfactants with different chains lengths.

    Matched MeSH terms: Sodium Chloride
  13. Fulltext Effects of different processing methods of human amniotic membrane on the quality of extracted RNA
    Rusidah Mat Yatim, Kannan, Thirumulu Ponnuraj, Suzina Sheikh Ab Hamid, Shazana Hilda Shamsudin
    Archives of Orofacial Sciences, 2013;8(2):47-53.
    MyJurnal
    The aim of this study was to determine the efficiency of different human amniotic membrane (HAM) processing methods on the concentration, purity and integrity of RNA. Two different techniques (Technique1 andTechnique2) were employed for the processing of HAM, which differed in terms of washing solution, sample storage conditions and processing time. Based on preservation of HAM, three groups were formed under each technique. In Technique 1, the groups were fresh frozen 1 (F1), glycerol preserved (GP) and gamma irradiated glycerol preserved (IGP); where else in Technique 2, the groups were fresh frozen 2 (F2), 50%glycerol/Dulbecco’s modified Eagle medium (DMEM) cryopre served HAM diluted with phosphate buffered saline(GB) and 50% glycerol/DMEM cryop reserved HAM diluted with diethyl procarbonate water (GD). Total RNA was extracted from the samples and their concentration, purity and integrity were examined. The F2 sample of which there was no pre-washing step and involved direct sample storage at-80oC, shorter processing time and chilled processing conditions had yielded better quality of RNA compared to the others.
    Matched MeSH terms: Sodium Chloride
  14. Fulltext Method optimization on the process of Iontophoresis with laser doppler fluximetry in the assessment of microvascular endothelial function
    Belqes Abdullah, A. T., Yvonne, T. G. B., Ahmad, S. H., Abdul Aziz, A. S. I., Aida, H. G. R.
    Malaysian Journal of Medicine and Health Sciences, 2011;7(1):35-40.
    MyJurnal
    Introduction: Iontophoresis of vasoactive substances such as acetylcholine (ACh) and sodium nitroprusside (SNP) combined with Laser Doppler fluximetry (LDF) is a non-invasive tool used to determine microvascular endothelial function. This study aims to test the effect of sodium chloride on
    non-specific vasodilatation when used as a vehicle in the process of iontophoresis. This study also aims to define the number of current pulses needed to get the maximum effect during iontophoresis with ACh and SNP using low current strength. Methods: The experiment was conducted in five healthy females. Baseline skin perfusion was taken before administration of seven current pulses. Current strength of 0.007 mA and current density of 0.01 mA/cm2 were used. Acetylcholine was used to assess endothelial dependent vasodilatation, while SNP was used to assess endothelial independent vasodilatation. The mean skin perfusion (AU) responses to the iontophoresis of ACh at the anodal and SNP at the cathode leads were recorded. Sodium chloride (0.9%) was used as a vehicle to obtain concentration of 1% for both ACh and SNP. Iontophoresis of pure vehicle (NaCl) was conducted on a separate day to observe the effect of vehicle only on the iontophoresis process at both anode and cathode. Results: Iontophoresis of NaCl showed no significant increase in perfusion compared to baseline at both anode and cathode. Significant increases in skin perfusion were observed with SNP and ACh; a plateau of ACh was reached from the 3rd pulse onwards; while the plateau of SNP was reached from the 4th pulse onwards. Conclusion: NaCl could be used as a vehicle for Ach and SNP during iontophoresis as it did not cause non-specific vasodilatation. Using five current pulses are adequate for iontophoresis of ACh and SNP to assess microvascular endothelial function.
    Matched MeSH terms: Sodium Chloride
  15. Fulltext Inadequate iodine intake among school children in Terengganu-findings from the national iodine deficiency disorder survey 2008
    Lim, Kuang Kuay, Chan, Ying Ying, Ahmad Ali Zainuddin, Teh, Chien Huey, Rusidah Selamat, Kee, Chee Cheong, et al.
    Int J Public Health Res, 2013;3(1):198-203.
    MyJurnal
    Iodine deficiency is still prevalent worldwide and it is the main cause of goiter, thyroid dysfunction and mental retardation. The aim of the study was to determine the iodine status and goiter prevalence among the school children in Terengganu. The representative sample consists of 1163 primary school children aged 8-10 years old randomly selected from urban and rural schools in Terengganu using stratified systematic random sampling technique. Urinary iodine levels in spot urine were determined by in house modified micro-method while goiter assessment was carried out by palpation of thyroid gland. The status of iodine deficiency was determined by the median urinary iodine concentrations (UIC) and total goiter prevalence (TGP) in accordance with the WHO criteria. The result showed the median [inter-quartile range (IQR)] urinary iodine concentrations was 78.7µg/L (50.1µg/L -120.0µg/L) indicating the iodine intake was slightly lower than recommended range of 100 µg/L. The rural school children had a significantly lower Iodine levels (median UIC=72.4µg/L, IQR=46.7µg/L -113.0µg/L) than the urban school children (median UIC=87.7µg/L, IQR=54.5 µg/L - 127.5µg/L). The total goiter prevalence (TGP) was 5.7%. The prevalence of goiter was significantly higher in rural (TGP=6.9%) compared to urban areas (TGP=3.6%). The study revealed that school children in Terengganu showed mild iodine deficiency and the condition is more pronounced in children from rural areas. The findings emphasize the importance of intervention implementation, universal salt iodization to ensure sufficient intake of iodine among the Terengganu school children.
    Matched MeSH terms: Sodium Chloride, Dietary
  16. Fulltext Physicochemical characteristics of gummy added with sutchi catfish (Pangasius hypophthalmus) gelatin
    Normah, I.
    International Food Research Journal, 2015;22(3):1059-1066.
    MyJurnal
    Gelatin from sutchi catfish (Pangasius hypophthalmus) skin was extracted and applied in the preparation of gummy in order to determine the suitability of sutchi catfish gelatin in gummy production. The skin was subjected to pre-treatment in the following sequence; 0.8M NaCl, 0.19 N NaOH followed by 0.12 N acetic acid prior to 12 hours extraction in distilled water at 50oC. The physicochemical characteristics of sutchi catfish gelatin was analysed and compared with the commercial bovine gelatin. Gummy added with sutchi catfish gelatin was also compared with gummy added with commercial gelatin. Analysis comprises of yield, gel strength, setting point and setting time, amino acid composition, texture profile analysis and sensory evaluation. The extraction resulted in 14.47% yield of gelatin. Sutchi catfish gelatin showed higher gel strength value (360.86 g) compared to the commercial gelatin (217.37 g) which is in accordance with proline content. Texture profile analysis showed that gummies prepared using sutchi catfish gelatin had significantly higher (p
    Matched MeSH terms: Sodium Chloride
  17. Fulltext Detection of tetrodotoxin and saxitoxin in dried salted yellow puffer fish (Xenopterus naritus) eggs from Satok Market, Kuching, Sarawak
    Mohd Nor Azman, A., Wan Norhana, M.N.
    International Food Research Journal, 2013;20(5):2963-2966.
    MyJurnal
    The detection of tetrodotoxin (TTX) and saxitoxin (STX) in dried salted yellow puffer fish (Xenopterus naritus) eggs bought from Satok Market, Kuching, Sarawak was carried out by mouse bioassay method. The amount of TTX and STX detected in the samples ranged from 95.6-195.5 Mouse Unit (MU)/g and 1.72-3.58 MU/g respectively. The results indicate that the dried salted eggs samples were found to contain TTX 9-20 times above the regulatory limit for human consumption (10 MU/g). Although detected, the amount of STX in salted eggs extract was slightly below the accepted threshold limit (4 MU/g). The local public in Sarawak should be educated on the potential danger of consuming dried salted puffer fish eggs in addition to the current warnings on puffer fish.
    Matched MeSH terms: Sodium Chloride
  18. Influence of sodium chloride treatment and polysaccharides as debittering agent on the physicochemical properties, antioxidant capacity and sensory characteristics of bitter gourd (Momordica charantia) juice
    Siti Rashima R, Maizura M, Kang WM, Fazilah A, Tan LX
    J Food Sci Technol, 2017 Jan;54(1):228-235.
    PMID: 28242920 DOI: 10.1007/s13197-016-2454-y
    The effects of sodium chloride (NaCl) (3.5%) solution and polysaccharides, such as carboxymethyl cellulose (CMC) (0.1, 0.3 and 0.5%) and gum arabic (5, 10 and 15%), on the physicochemical properties, antioxidant capacity and sensory characteristics of bitter gourd juice were investigated. An increase in the concentration of CMC and gum arabic significantly was observed to increase the lightness (L value) and the viscosity (mPas) of bitter gourd juice at all levels. Increased concentrations of gum arabic significantly increased the total soluble solids. The bitter gourd fruit treated with NaCl solution produced the highest lightness (L value) and scavenging activity of free radical 2,2-diphenyl-1-picrylhydrazyl of bitter gourd juice. Increased concentration of gum arabic up to 15% significantly increased the total phenolic content. The addition of 5% gum arabic effectively reduced the bitterness of the bitter gourd juice. Viscosity of the juice resulted in negative correlation for bitterness.
    Matched MeSH terms: Sodium Chloride
  19. Fulltext Comparison of Pressure-Retarded Osmosis Performance between Pilot-Scale Cellulose Triacetate Hollow-fiber and Polyamide Spiral-Wound Membrane Modules
    Kakihana Y, Jullok N, Shibuya M, Ikebe Y, Higa M
    Membranes (Basel), 2021 Feb 28;11(3).
    PMID: 33671075 DOI: 10.3390/membranes11030177
    Pressure-retarded osmosis (PRO) has recently received attention because of its ability to generate power via an osmotic pressure gradient between two solutions with different salinities: high- and low-salinity water sources. In this study, PRO performance, using the two pilot-scale PRO membrane modules with different configurations-five-inch cellulose triacetate hollow-fiber membrane module (CTA-HF) and eight-inch polyamide spiral-wound membrane modules (PA-SW)-was evaluated by changing the draw solution (DS) concentration, applied hydrostatic pressure difference, and the flow rates of DS and feed solution (FS), to obtain the optimum operating conditions in PRO configuration. The maximum power density per unit membrane area of PA-SW at 0.6 M NaCl was 1.40 W/m2 and 2.03-fold higher than that of CTA-HF, due to the higher water permeability coefficient of PA-SW. In contrast, the maximum power density per unit volume of CTA-SW at 0.6 M NaCl was 4.67 kW/m3 and 6.87-fold higher than that of PA-SW. The value of CTA-HF increased to 13.61 kW/m3 at 1.2 M NaCl and was 12.0-fold higher than that of PA-SW because of the higher packing density of CTA-HF.
    Matched MeSH terms: Sodium Chloride
  20. Fulltext Evaluation of the Estimation Capability of Response Surface Methodology and Artificial Neural Network for the Optimization of Bacteriocin-Like Inhibitory Substances Production by Lactococcus lactis Gh1
    Jawan R, Abbasiliasi S, Tan JS, Kapri MR, Mustafa S, Halim M, et al.
    Microorganisms, 2021 Mar 12;9(3).
    PMID: 33809201 DOI: 10.3390/microorganisms9030579
    Bacteriocin-like inhibitory substances (BLIS) produced by Lactococcus lactis Gh1 had shown antimicrobial activity against Listeria monocytogenes ATCC 15313. Brain Heart Infusion (BHI) broth is used for the cultivation and enumeration of lactic acid bacteria, but there is a need to improve the current medium composition for enhancement of BLIS production, and one of the approaches is to model the optimization process and identify the most appropriate medium formulation. Response surface methodology (RSM) and artificial neural network (ANN) models were employed in this study. In medium optimization, ANN (R2 = 0.98) methodology provided better estimation point and data fitting as compared to RSM (R2 = 0.79). In ANN, the optimal medium consisted of 35.38 g/L soytone, 16 g/L fructose, 3.25 g/L sodium chloride (NaCl) and 5.40 g/L disodium phosphate (Na2HPO4). BLIS production in optimal medium (717.13 ± 0.76 AU/mL) was about 1.40-fold higher than that obtained in nonoptimised (520.56 ± 3.37 AU/mL) medium. BLIS production was further improved by about 1.18 times higher in 2 L stirred tank bioreactor (787.40 ± 1.30 AU/mL) as compared to that obtained in 250 mL shake flask (665.28 ± 14.22 AU/mL) using the optimised medium.
    Matched MeSH terms: Sodium Chloride
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links