The alkali-silica reaction (ASR) is an important consideration in ensuring the long-term durability of concrete materials, especially for those containing reactive aggregates. Although fly ash (FA) has proven to be useful in preventing ASR expansion, the filler effect and the effect of FA fineness on ASR expansion are not well defined in the present literature. Hence, this study aimed to examine the effects of the filler and fineness of FA on ASR mortar expansion. FAs with two different finenesses were used to substitute ordinary Portland cement (OPC) at 20% by weight of binder. River sand (RS) with the same fineness as the FA was also used to replace OPC at the same rate as FA. The replacement of OPC with RS (an inert material) was carried out to observe the filler effect of FA on ASR. The results showed that FA and RS provided lower ASR expansions compared with the control mortar. Fine and coarse fly ashes in this study had almost the same effectiveness in mitigating the ASR expansion of the mortars. For the filler effect, smaller particles of RS had more influence on the ASR reduction than RS with coarser particles. A significant mitigation of the ASR expansion was obtained by decreasing the OPC content in the mortar mixture through its partial substitution with FA and RS.
One of the most crucial attributes of synthetic organic chemistry is to design organic reactions under the facets of green chemistry for the sustainable production of chemicals. Thus, due to the intensified environmental and safety concern, the need for new technologies for conducting chemical transformation has grown. In this regard, there is enormous interest in the use of heterogeneous catalysts as they generally avoid the generation of waste, require fewer toxic reagents, as well as entail easier separation and recycling of the catalyst. α,β-Unsaturated acids have been widely used in various industrial applications and have been identified as one of the most promising chemicals obtained via the Knoevenagel condensation reaction. This review aims to discuss the most pertinent heterogeneous catalytic systems such as zeolites, mesoporous silica, ionic liquids, metal oxides, and graphitic carbon nitride-based catalysts in the Knoevenagel reaction. Ultimately, this review focuses not only on the catalyst but also provides an overall idea and guide for the preparation of new catalysts with outstanding properties by looking at the chemical and engineering aspects such as the reaction conditions and the mechanisms.
Previous studies on screening of lignin-degrading bacteria mainly focused on the ligninolytic ability of the isolated bacteria for the utilization of lignin monomers. In this study, we focused on the depolymerization of alkali lignin to prove the ability of the isolated thermophilic bacterial strains to utilize and depolymerize more than a monomer of alkali lignin within 7 days of incubation. Indigenous thermophilic bacterial isolates from the palm oil plantation were used to evaluate the depolymerization and utilization of alkali lignin. The confirmation of the bacterium-mediated depolymerization of oil palm empty fruit bunch was achieved through the removal of silica bodies, as observed with scanning electron microscopy. Stenotrophomonas sp. S2 and Bacillus subtilis S11Y were able to reduce approximately 50% and 20% of alkali lignin at 7 days of incubation without the requirement for additional carbon sources.
Catalytic esterification of glycerol with oleic acid (OA) was optimized over hydrophobic mesoporous zirconia-silica heterogeneous acid catalyst (ZrO2-SiO2-Me&Et-PhSO3H) and benchmarked with commercial catalysts (Aquivion and Amberlyst 15) in order to examine the effect of catalyst acidity on conversion, yield and product selectivity. The process optimisation results showed an 80% conversion with a 59.4% glycerol mono-oleate (GMO) and 34.6% glycerol dioleate (GDO) selectivities corresponding to a combined GMO and GDO selectivity of 94.8% at equimolar OA-to-glycerol ratio, 160°C reaction temperature, 5 wt% catalyst concentration with respect to the OA weight and 4 h reaction time. This work reveals that the hydrophobic and mild acidic ZrO2-SiO2-Me&Et-PhSO3H catalyst outperformed Amberlyst 15 and Aquivion with a yield of 82% and GMO selectivity of 60%. It is found that catalyst acidity is a key parameter for catalytic activity and conversion rate. Nevertheless, high acidity/acid strength reduced the product yield in the glycerol esterification of OA.
A urea precursor was used for the first time to prepare mesoporous carbon nitride (MCN) by a thermal polymerization process with silica nanospheres as a hard template. Although the prepared MCN samples have similar structures and optical properties, it was revealed that the specific surface area, pore-size distribution, and morphology of the MCN samples depend on the initial mass ratio of urea to silica. Compared to the bulk carbon nitride (BCN) that only gave 20% phenol removal (6 h of irradiation), the activities can be enhanced up to 74% on MCN samples for photocatalytic removal of phenol under visible-light irradiation. The highest conversion was obtained on MCN with an initial mass ratio of urea to silica of 5, which has high surface area of 191 m(2) g(-1) and a nanoporous structure with uniform pore-size distribution of 7 nm. In addition to the high activity, the MCN sample also showed high photocatalytic stability.
Herein, a rapid and sensitive current-volt measurement was developed for identifying the IS6110 DNA sequence to diagnose Mycobacterium tuberculosis (TB). An aminated capture probe was immobilized on a 1,1'-carbonyldiimidazole-functionalized interdigitated electrode (IDE) silica substrate, and the target sequence was detected by complementation. It was found that all tested concentrations displayed a higher response in current changes than the control, and the limit of detection was 10 fM. The sensitivity ranged from 1 to 10 fM. The control sequences with single-, triple-mismatch and noncomplementary sequences showed great discrimination. This rapid and easy DNA detection method helps to identify M. tuberculosis for early-stage diagnosis of TB.
Introduction: Rice husk has portrayed great potential in becoming a sustainable biomass source in producing silica, cellulose and carbon materials, which garnered widespread interest among researchers. The objective of the current study is to determine the morphological and compositional changes in rice husk due to the synergistic effects of ther- mochemical treatment. Methods: Washed and dried rice husk was blended into a fine powder and then subjected to step-wise heat treatment and acid digestion to produce white ash. The intermittent products, as well as the original rice husk and the final ash product, were characterised using analytical instruments to document the morphologi- cal and chemical composition changes. Results: This report highlights the production of pure rice husk ash using a step-wise treatment using a combination of thermochemical treatment and carbonisation. The results showed that a partial breakdown of the lignocellulose components was achieved using directed thermal treatment at low tem- perature. The ionic impurities were leached out in subsequent heated acid treatment. Thereafter, the carbonaceous organic matter was completely converted to carbon during the carbonisation of the sample and the remaining carbon residue was removed during calcination. High purity ash contained agglomerated and nanostructured silica in the dimensions of 20 to 50 nm in the amorphous form. Conclusion: The step-wise treatment allowed systematic removal of each compound while maintaining the amorphous mineral phase of silica and avoiding carbon fixation. Under- standing the effect of each treatment offers insight to produce purer silica from rice husk.
Grog is an additive material that plays important roles in ceramic making. It improves the fabrication process of green bodies as well as the physical properties of fired bodies. Few low-cost materials and wastes have found their application as grog in recent years, thus encouraging the replacement of commercial grogs with cost-saving materials. Coal fly ash, a combustion waste produced by coal-fired power plant, has the potential to be converted into grog owing to its small particle sizes and high content of silica and alumina. In this study, grog was derived from coal fly ash and mixed with kaolin clay to produce ceramics. Effects of the grog addition on the resultant ceramics were investigated. It was found that, to a certain extent, the grog addition reduced the firing shrinkage and increased the total porosity of the ceramics. The dimensional stability of the ceramics at a firing temperature of 1200 °C was also not noticeably affected by the grog. However, the grog addition in general had negative effects on the biaxial flexural strength and refractoriness of the ceramics.
Soda lime silica (SLS) waste as the source of silica (SiO2) and ark clamshell (ACS) as the foaming agent has been utilized to fabricate the low-cost and lightweight foam glass-ceramics. A series of 1 and 6 wt% foam glass-ceramics were successfully prepared by the conventional solid-state sintering method at various sintering temperatures for 60 min. The bulk density of the samples has achieved minimum density (1.014 g/cm3) with maximum expansion (62.31%) at 6 wt% of the ACS content sintered at 800 °C for 60 min. The bulk density increases while the linear shrinkage and total porosity decrease with the progression of ACS contents and sintering temperature, where the results correspond with the FESEM micrograph. The result of XRD and FTIR transmittance spectra have shown that the formation of wollastonite crystal has occurred starting at 6 wt% of the ACS content sintered at 800 °C for 30 min. The highest mechanical performance (3.90 MPa) with an average total porosity (8.04%) is observed for the sample containing 1 wt% of ACS. It can be concluded that the composition of foam glass-ceramics (1 and 6 wt%) and sintering temperatures give significant results to the structural, physical, and mechanical properties of the fabricated foam glass-ceramics.
Powdered-photocatalysis of organic wastewater is widely investigated, unfortunately not industrially implemented due to its high energy requirement. Interestingly, such issue may be alleviated via the elimination of mechanical stirring required. Core-shell ZnO-based photocatalysts were developed herein, subsequently demonstrated efficient photocatalytic activities in the absence of mechanical stirring. Results show that the developed SiO2-cored ZnO photocatalyst are highly crystalline, while significantly smaller than coreless, pure ZnO due to the multi-point crystallization prompted. Additionally, it is also inherited with considerable buoyancy ability from SiO2-core in the absence of mechanical stirring, concurrently rendered with UV-active properties due to its ZnO-shell. Experimentally, 55% of particles of ZnO_0.0025 (0.0025 mol of ZnO-deposition) were found stably suspended for 60 min in liquid substrate, as opposed to the instant-settling of pure ZnO particles. In term of photocatalytic activity, ZnO_0.01 manifested the best methylene blue (MB) degradation with 150 mL/min of O2-bubbling. 67.63% of MB was degraded with photocatalyst loading of 0.2 g/L after 120 min UV-irradiation, simultaneously recorded the highest pseudo-first order reaction constant of 9.636 × 10-3 min-1. As summary, the auto-suspending photocatalysis conceptualized in current study offers a high possibility in reducing energy requirement for photo-treatment of wastewater, hence advocating its industrialization potential in near future.
In this work, fibrous silica-titania (FST) was successfully prepared by the microemulsion method prior to the addition of three types of carbonaceous materials: graphitic-carbon nitride, g-C3N4 (CN), graphene nanoplatelets (GN), and multi-wall carbon nanotubes, MWCNT (CNT), via a solid-state microwave irradiation technique. The catalysts were characterized using XRD, FESEM, TEM, FTIR, UV-Vis DRS, N2 adsorption-desorption, XPS and ESR, while their photoactivity was examined on the degradation of toxic 2-chlorophenol (2-CP). The result demonstrated that the initial reaction rate was in the following order: CNFST (5.1 × 10-3 mM min-1) > GNFST (2.5 × 10-3 mM min-1) > CNTFST (2.3 × 10-3 mM min-1). The best performance was due to the polymeric structure of g-C3N4 with a good dispersion of C and N on the surface FST. This dispersion contributed towards an appropriate quantity of defect sites, as a consequence of the greater interaction between g-C3N4 and the FST support, that led to narrowed of band gap energy (2.98 eV to 2.10 eV). The effect of scavenger and ESR studies confirmed that the photodegradation over CNFST occurred via a Z-scheme mechanism. It is noteworthy that the addition of green carbonaceous materials on the FST markedly enhanced the photodegradation of toxic 2-CP.
We formulated a pH-sensitive chlorhexidine-loaded mesoporous silica nanoparticles (MSN) modified with poly-(lactic-co-glycolic acid) (CHX-loaded/MSN-PLGA) and incorporated into experimental resin-based dentin adhesives at 5 and 10 wt%. Nanocarriers were characterized in terms of morphology, physicochemical features, spectral analyses, drug-release kinetics at varying pH and its effect on dentin-bound proteases was investigated. The modified dentin adhesives were characterized for cytotoxicity, antimicrobial activity, degree of conversion (DC) along with CHX release, micro-tensile bond strength (μTBS) and nano-leakage expression were studied at different pH values and storage time. CHX-loaded/MSN-PLGA nanocarriers exhibited a significant pH-dependent drug release behavior than CHX-loaded/MSN nanocarriers without PLGA modification. The highest percentage of CHX release was seen with 10 wt% CHX-loaded/MSN-PLGA doped adhesive at a pH of 5.0. CHX-loaded/MSN-PLGA modified adhesives exhibited more profound antibiofilm characteristics against S. mutans and more sustained CHX-release which was pH dependent. After 6 months in artificial saliva at varying pH, the 5 wt% CHX-loaded/MSN-PLGA doped adhesive showed excellent bonding under SEM/TEM, higher μTBS, and least nano-leakage expression. The pH-sensitive CHX-loaded/MSN-PLGA could be of crucial advantage for resin-dentin bonding applications especially in reduced pH microenvironment resulting from biofilm formation; and the activation of dentin-bound proteases as a consequence of acid etching and acidic content of bonding resin monomers.
This paper aimed to describe the effects of sand mining on the Kelantan River with respect to physical and chemical parameter analyses. Three replicates of water samples were collected from five stations along the Kelantan River (November 2010 until February 2011). The physical parameters included water temperature, water conductivity, dissolved oxygen (DO), pH, total dissolved solids (TDS), total suspended solids (TSS) and turbidity, whereas the chemical parameters included the concentration of nitrogen nutrients such as ammonia, nitrate and nitrite. The Kelantan River case study revealed that TSS, turbidity and nitrate contents exceed the Malaysian Interim National Water Quality Standard (INWQS) range and are significantly different between Station 1 (KK) and Station 3 (TM). Station 1 has the largest variation of TDS, TSS, turbidity and nitrogen nutrients because of sand mining and upstream logging activities. The extremely high content of TSS and the turbidity have caused poor and stressful conditions for the aquatic life in the Kelantan River.
Kaempferia parviflora is an ethnomedicinally important plant. Conventional propagation of K. parviflora is hindered by slow growth rate, long dormancy periods and dual use of rhizomes for seeds as well as marketable produce. In our study, we developed a promising dual-phase micropropagation protocol to increase number of plantlets, survivability, biomass and quality plantlets for mass production. Multiple shoot regeneration was found most successful on Murashige and Skoog (MS) media supplemented with 35.52 μM N6-benzyladenine (BA) in terms of highest number of shoots (22.4 ± 1.84), leaves (29.27 ± 1.30), and roots (17.8 ± 1.72) per explant. High survivability was observed with an acclimatisation percentage of 100% in sterile perlite medium. This method was shown to be preferable compared to conventional propagation in terms of propagation time and number of plantlets. Regenerated in vitro plantlets were then successfully induced to form microrhizomes in MS media with an optimal concentration of 6% (w/v) sucrose. Increase in microrhizome biomass (35.7 ± 2.59 g per flask), number of microrhizomes (5.2 ± 0.78), shoots (8.5 ± 1.58) and roots (8.5 ± 1.58) were observed for this treatment. This investigation successfully highlights the manipulation of single factors in short time frame to produce a simple and efficient alternative propagation method for K. parviflora.
A study was carried out to investigate correlation between presence of specific microalgal species and Leptoconops biting midge larvae in its breeding habitats. Sand samples containing microalgae were collected from the beach where the midges were most commonly biting and from sand beaches which are potential as breeding habitats of Leptoconops. The survey covered sand beaches from 12 seperate islands. At all sites, the Bacillariophyta constituted the largest representatives of the microalgae community with the majority from the Naviculaceae family. A total of 24 microalgal species were identified from the sand samples collected from the study sites. Sand samples from Kentot Kecil Island had the highest number of algal species (11.0) and the highest algae species diversity ( Shanon-Weiner Diversity Index, H' = 0.884). Besar Island (Johor) had the lowest number of algal species (2.0) whereas Tengol A Island had the lowest algae species diversity (H'=0.234). Highest similarity index was recorded between sand samples collected from Tengol A Island and Tengol B Island (75.0%) followed by Besar Island (Melaka) and Tengol B Island (62.0 %). The variation between other islands were relatively high. Virtually many kinds of algae were found where Leptoconops were breeding but Fragilaria intermedia, Mastigloia minuta and Navicula advena were particularly common.
This paper reports an alternative method for making glass-ceramic from disposal waste water
sludge and soda lime silica (SLS) glass. The glass ceramic samples were prepared from a mixture
of wastewater sludge and SLS glasses, melted at 1375°C for 3 hours and quenched by pouring into
water to obtain a coarse frit. The frit glass was then crushed and sieved to 106μm before it was
pressed to a pellet. The sintering process was performed at various temperatures between 700-
1000°C for 2 hours and morphologically characterized with XRD, SEM, and EDX. Overall results
showed the crystalline phase of diopside sodian-critobalite glass-ceramic is depending on thermal
treatment process and making them attractive to industrial uses such as in construction, tiling, and
glass-ceramic applications.
A 'green tyre' concept has the advantage of low rolling resistance, improved wet grip and enhanced handling. It has been reported that 3% decrease in rolling resistance is equivalent to 1% fuel saving, thus giving the 'green tyre' economic benefits and customer satisfaction. In this study, epoxidised natural rubber (ENR) compounds containing various loading of silica filler were prepared. The processibility and viscoelastic properties were investigated using the rubber processing analyser and Mooney viscometer. Results showed that the properties were adversely affected by the poor dispersion of silica as supported by the bound rubber measurement. In addition, a reversion in the cure behaviour was also observed as the curing temperature was increased to 170ºC.
Since its invention, polyimide (PI) has been widely used in micro-electro-mechanical system (MEMS) devices. For fabrication, the PI membrane, PI-2723 HD-Microsystems was used as the membrane material due to its Young's modulus of 2.7 GPa and its film thickness could easily be controlled by changing the speed of the spin coater system. The application PI as membrane structure on silicon wafers therefore gave a much better mechanical performance then conventional membranes made of silicon dioxide (SiO2) or silicon nitride (Si3N4) layers. The fabrication of PI membrane was the same as for SiO2 and Si3N4 membranes; the basic step was to etch a side of the silicon wafer using wet anisotropic etching. This paper proposes an effective process for fabrication of PI membrane with f ast and little supervision. In this process, a dual step process was wet anisotropic etching of single crystal silicon using pottasium hydroxyl (KOH) with different concentrations and temperature processes. For the first process, 45% KOH under boiling temperature was used to etch at least 90%–95% of the silicon. In the second process, the silicon was submerged in 45% KOH with temperature at 70ºC–80ºC to etch away the residual silicon until a clean and transparent PI membrane was achieved. Using this method, the fabrication of PI membrane could be generated fast.
Fly ash (PFA) is a complex material produced after combustion in coal-fired power plants. About half of this fly ash is disposed as solid wastes. A possible alternative to disposal of the fly ash is the synthesis of zeolite. Zeolite Boggsite (Na37Ca74Al185Si775O192 7H2O) was synthesized from fly ash by hydrothermal treatment with NaOH solutions as identified by x-ray diffraction. The zeolite type and degree of crystallization were found to be dependent on the reaction conditions and mineralogy of the raw material, particularly in terms of the relative concentrations of SiO2 and Al2O3.
The amount of sugarcane bagasse and rice straw in the state of Perlis (Malaysia) is abundant while its utilization is still limited. One of the alternatives for the bagasse and straw utilization is as pulp raw material. This paper reviews on pulp from sugarcane bagasse and rice straw and its suitability for paper production. In this study, the pulp was extracted by the Soxhlet extraction method. The objective of this study was to investigate the cellulose, lignin and silica content of the pulp from sugarcane bagasse and rice straw. For rice straw, the presence of large amount of pentosanes in the pulp and black liquors, which also contain silica were decreased the using of straw in the paper industry. Therefore, formic acid pulping and NaOH treatment are studied to reduce or prevent silica. The isolated pulp samples were further characterized by Scanning Electron Microscope (SEM) to investigate their fiber dimensions.