MyMedR

Displaying publications 161 - 180 of 428 in total

Abstract:

Sort:

Fulltext Experimental Investigation of the Effect of the Driving Voltage of an Electroadhesion Actuator

Koh KH, Sreekumar M, Ponnambalam SG

Materials (Basel), 2014 Jun 25;7(7):4963-4981.
PMID: 28788114 DOI: 10.3390/ma7074963

This paper investigates the effect of driving voltage on the attachment force of an electroadhesion actuator, as the existing literature on the saturation of the adhesive force at a higher electric field is incomplete. A new type of electroadhesion actuator using normally available materials, such as aluminum foil, PVC tape and a silicone rubber sheet used for keyboard protection, has been developed with a simple layered structure that is capable of developing adhesive force consistently. The developed actuator is subjected to the experiment for the evaluation of various test surfaces; aluminum, brick, ceramic, concrete and glass. The driving high voltage is varied in steps to determine the characteristics of the output holding force. Results show a quadratic relation between F (adhesion force) and V (driving voltage) within the 2 kV range. After this range, the F-V responses consistently show a saturation trend at high electric fields. Next, the concept of the leakage current that can occur in the dielectric material and the corona discharge through air has been introduced. Results show that the voltage level, which corresponds to the beginning of the supply current, matches well with the beginning of the force saturation. With the confirmation of this hypothesis, a working model for electroadhesion actuation is proposed. Based on the experimental results, it is proposed that such a kind of actuator can be driven within a range of optimum high voltage to remain electrically efficient. This practice is recommended for the future design, development and characterization of electroadhesion actuators for robotic applications.

Matched MeSH terms: Aluminum
The impact of electrolyte on the adsorption of the anionic surfactant methyl ester sulfonate at the air-solution interface: Surface multilayer formation

Xu H, Thomas RK, Penfold J, Li PX, Ma K, Welbourne RJL, et al.

J Colloid Interface Sci, 2018 Feb 15;512:231-238.
PMID: 29073464 DOI: 10.1016/j.jcis.2017.10.064

The methyl ester sulfonates represent a promising group of anionic surfactants which have the potential for improved performance and biocompatibility in a range of applications. Their solution properties, in particular their tolerance to hard water, suggests that surface ordering may occur in the presence of multi-valent counterion. Understanding their adsorption properties in a range of different circumstances is key to the exploitation of their potential. Neutron reflectivity and surface tension have been used to characterise the adsorption at the air-aqueous solution interface of the anionic surfactant sodium tetradecanoic 2-sulfo 1-methyl ester, C14MES, in the absence of electrolyte and in the presence of mono, di, and tri-valent counterions, Na+, Ca2+, and Al3+. In particular the emphasis has been on exploring the tendency to form layered structures at the interface. In the absence of electrolyte and in the presence of NaCl and CaCl2 and AlCl3 at low concentrations monolayer adsorption is observed, and the addition of electrolyte results in enhanced adsorption. In the presence of NaCl and CaCl2 only monolayer adsorption is observed. However at higher AlCl3 concentrations surface multilayer formation is observed, in which the number of bilayers at the surface depends upon the surfactant and AlCl3 concentrations.

Matched MeSH terms: Aluminum Compounds
Effect of Milling Time on the Microstructure, Physical and Mechanical Properties of Al-Al₂O₃ Nanocomposite Synthesized by Ball Milling and Powder Metallurgy

Toozandehjani M, Matori KA, Ostovan F, Abdul Aziz S, Mamat MS

Materials (Basel), 2017 Oct 26;10(11).
PMID: 29072632 DOI: 10.3390/ma10111232

The effect of milling time on the morphology, microstructure, physical and mechanical properties of pure Al-5 wt % Al₂O₃ (Al-5Al₂O₃) has been investigated. Al-5Al₂O₃ nanocomposites were fabricated using ball milling in a powder metallurgy route. The increase in the milling time resulted in the homogenous dispersion of 5 wt % Al₂O₃ nanoparticles, the reduction of particle clustering, and the reduction of distances between the composite particles. The significant grain refining during milling was revealed which showed as a reduction of particle size resulting from longer milling time. X-Ray diffraction (XRD) analysis of the nanocomposite powders also showed that designated ball milling contributes to the crystalline refining and accumulation of internal stress due to induced severe plastic deformation of the particles. It can be argued that these morphological and microstructural variations of nanocomposite powders induced by designated ball milling time was found to contribute to an improvement in the density, densification, micro-hardness (HV), nano-hardness (HN), and Young's modulus (E) of Al-5Al₂O₃ nanocomposites. HV, HN, and E values of nanocomposites were increased by ~48%, 46%, and 40%, after 12 h of milling, respectively.

Matched MeSH terms: Aluminum Oxide
Fulltext Hydrogen Production by Steam Reforming of Ethanol over Nickel Catalysts Supported on Sol Gel Made Alumina: Influence of Calcination Temperature on Supports

Yaakob Z, Bshish A, Ebshish A, Tasirin SM, Alhasan FH

Materials (Basel), 2013 May 30;6(6):2229-2239.
PMID: 28809270 DOI: 10.3390/ma6062229

Selecting a proper support in the catalyst system plays an important role in hydrogen production via ethanol steam reforming. In this study, sol gel made alumina supports prepared for nickel (Ni) catalysts were calcined at different temperatures. A series of (Ni/AlS.G.) catalysts were synthesized by an impregnation procedure. The influence of varying the calcination temperature of the sol gel made supports on catalyst activity was tested in ethanol reforming reaction. The characteristics of the sol gel alumina supports and Ni catalysts were affected by the calcination temperature of the supports. The structure of the sol gel made alumina supports was transformed in the order of γ → (γ + θ) → θ-alumina as the calcination temperature of the supports increased from 600 °C to 1000 °C. Both hydrogen yield and ethanol conversion presented a volcano-shaped behavior with maximum values of 4.3 mol/mol ethanol fed and 99.5%, respectively. The optimum values were exhibited over Ni/AlS.G800 (Ni catalyst supported on sol gel made alumina calcined at 800 °C). The high performance of the Ni/AlS.G800 catalyst may be attributed to the strong interaction of Ni species and sol gel made alumina which lead to high nickel dispersion and small particle size.

Matched MeSH terms: Aluminum Oxide
Fulltext Hot Press as a Sustainable Direct Recycling Technique of Aluminium: Mechanical Properties and Surface Integrity

Yusuf NK, Lajis MA, Ahmad A

Materials (Basel), 2017 Aug 03;10(8).
PMID: 28771207 DOI: 10.3390/ma10080902

Meltless recycling technique has been utilized to overcome the lack of primary resources, focusing on reducing the usage of energy and materials. Hot press was proposed as a novel direct recycling technique which results in astoundingly low energy usage in contrast with conventional recycling. The aim of this study is to prove the technical feasibility of this approach by characterizing the recycled samples. For this purpose, AA6061 aluminium chips were recycled by utilizing hot press process under various operating temperature (Ts = 430, 480, and 530 °C) and holding times (ts = 60, 90, and 120 min). The maximum mechanical properties of recycled chip are Ultimate tensile strength (UTS) = 266.78 MPa, Elongation to failure (ETF) = 16.129%, while, for surface integrity of the chips, the calculated microhardness is 81.744 HV, exhibited at Ts = 530 °C and ts = 120 min. It is comparable to theoretical AA6061 T4-temper where maximum UTS and microhardness is increased up to 9.27% and 20.48%, respectively. As the desired mechanical properties of forgings can only be obtained by means of a final heat treatment, T5-temper, aging after forging process was employed. Heat treated recycled billet AA6061 (T5-temper) are considered comparable with as-received AA6061 T6, where the value of microhardness (98.649 HV) at 175 °C and 120 min of aging condition was revealed to be greater than 3.18%. Although it is quite early to put a base mainly on the observations in experimental settings, the potential for significant improvement offered by the direct recycling methods for production aluminium scrap can be clearly demonstrated. This overtures perspectives for industrial development of solid state recycling processes as environmentally benign alternatives of current melting based practices.

Matched MeSH terms: Aluminum
Fulltext The influence of visual art therapy on paediatric dental patient: a pilot study

Manan, N.M., Zainal Abidin, H.A., Mohd Zahari, N., Abdul Ghafar@Abdul Rapor, A.

Ann Dent, 2015;22(2):9-14.
MyJurnal

Objective: This study examined the influence of visual art therapy techniques in reducing anxiety level
among 4 to 6 years old paediatric dental patients.
Methods: Eleven subjects were selected among 4 to 6 years old paediatric dental patients. The initial
reaction towards dental procedure/treatment was evaluated using Frankl Behavior Rating Scale. The
anxiety level was assessed by using Malay-Modified Child Dental Anxiety Scale (MCDASf
) to measure
a child situational anxiety of pre- and post-treatment. Visual art making activities included free drawing,
clay moulding and collage technique. The participant reaction to dental treatment was assessed by using
Frankl Behavioural Rating Scale for two subsequent independent visits in two weeks interval. Median
and Ordinal Test ranked the variables score of behavioural reaction towards dental treatment and anxiety
level.
Results: Play-doh (PD) subjects could accept dental procedures more if compared to free drawing (FD)
and storytelling by collage (ST) subjects, which has lower post treatment-median scores in Visit 1 and
Visit 2, FD and ST subjects need more time to show positive attitude towards dental treatment.
Conclusion: These findings suggest dental anxiety level of children aged 4 to 6 years old reduced after
the art therapy and play-doh(clay-moulding technique) is the art making activity of choice among 4 to 6
years old paediatric dental patients.

Matched MeSH terms: Aluminum Silicates
Fulltext Effect of Luting Cements On the Bond Strength to Turkom-Cera All-Ceramic Material

Al-Makramani BMA, Razak AAA, Abu-Hassan MI, Al-Sanabani FA, Albakri FM

Open Access Maced J Med Sci, 2018 Mar 15;6(3):548-553.
PMID: 29610618 DOI: 10.3889/oamjms.2018.111

BACKGROUND: The selection of the appropriate luting cement is a key factor for achieving a strong bond between prepared teeth and dental restorations.
AIM: To evaluate the shear bond strength of Zinc phosphate cement Elite, glass ionomer cement Fuji I, resin-modified glass ionomer cement Fuji Plus and resin luting cement Panavia-F to Turkom-Cera all-ceramic material.
MATERIALS AND METHODS: Turkom-Cera was used to form discs 10mm in diameter and 3 mm in thickness (n = 40). The ceramic discs were wet ground, air - particle abraded with 50 - μm aluminium oxide particles and randomly divided into four groups (n = 10). The luting cement was bonded to Turkom-Cera discs as per manufacturer instructions. The shear bond strengths were determined using the universal testing machine at a crosshead speed of 0.5 mm/min. The data were analysed using the tests One Way ANOVA, the nonparametric Kruskal - Wallis test and Mann - Whitney Post hoc test.
RESULTS: The shear bond strength of the Elite, Fuji I, Fuji Plus and Panavia F groups were: 0.92 ± 0.42, 2.04 ± 0.78, 4.37 ± 1.18, and 16.42 ± 3.38 MPa, respectively. There was the statistically significant difference between the four luting cement tested (p < 0.05).
CONCLUSION: the phosphate-containing resin cement Panavia-F exhibited shear bond strength value significantly higher than all materials tested.

Matched MeSH terms: Aluminum Oxide
Fulltext Removal of metal ions and humic acids through polyetherimide membrane with grafted bentonite clay

Hebbar RS, Isloor AM, Prabhu B, Inamuddin, Asiri AM, Ismail AF

Sci Rep, 2018 03 16;8(1):4665.
PMID: 29549259 DOI: 10.1038/s41598-018-22837-1

Functional surfaces and polymers with branched structures have a major impact on physicochemical properties and performance of membrane materials. With the aim of greener approach for enhancement of permeation, fouling resistance and detrimental heavy metal ion rejection capacity of polyetherimide membrane, novel grafting of poly (4-styrenesulfonate) brushes on low cost, natural bentonite was carried out via distillation-precipitation polymerisation method and employed as a performance modifier. It has been demonstrated that, modified bentonite clay exhibited significant improvement in the hydrophilicity, porosity, and water uptake capacity with 3 wt. % of additive dosage. SEM and AFM analysis showed the increase in macrovoides and surface roughness with increased additive concentration. Moreover, the inclusion of modified bentonite displayed an increase in permeation rate and high anti-irreversible fouling properties with reversible fouling ratio of 75.6%. The humic acid rejection study revealed that, PEM-3 membrane having rejection efficiency up to 87.6% and foulants can be easily removed by simple hydraulic cleaning. Further, nanocomposite membranes can be significantly employed for the removal of hazardous heavy metal ions with a rejection rate of 80% and its tentative mechanism was discussed. Conspicuously, bentonite clay-bearing poly (4-styrenesulfonate) brushes are having a synergistic effect on physicochemical properties of nanocomposite membrane to enhance the performance in real field applications.

Matched MeSH terms: Aluminum Silicates
Catalytic fast pyrolysis of durian rind using silica-alumina catalyst: Effects of pyrolysis parameters

Tan YL, Abdullah AZ, Hameed BH

Bioresour Technol, 2018 Sep;264:198-205.
PMID: 29803811 DOI: 10.1016/j.biortech.2018.05.058

Silica-alumina catalyst was prepared and used in the catalytic fast pyrolysis of durian rind in a drop-type two-stage reactor. The effects of catalytic temperature (400 °C-600 °C) and catalyst-to-durian rind ratio (1:30-3:30) were evaluated. Bio-oil yield was increased with increased catalytic temperature due to considerable dehydration process, but it was reduced with high catalyst loading due to the overcracking of organics into light gases. Silica-alumina catalyst possessed good selectivity and the products changed according to the temperature. The major components in bio-oil were hydrocarbons, furan derivatives, and aromatic compounds at 400 °C, 500 °C, and 600 °C, respectively. The hydrogen and carbon contents of bio-oil were reduced with high catalyst loading due to the overcracking of organics, and the deoxygenation process became unfavorable. The silica-alumina catalyst worked well in catalytic fast pyrolysis of durian rind, and the condition may be adjusted based on the desired products.

Matched MeSH terms: Aluminum Oxide
Fulltext Sensitivity study of Graphene Nanoribbon with NH3 at room temperature

Guan Ling Sim, Mohd Nizar Hamidon, Kamilu Iman Usman

Pertanika Journal of Science & Technology, 2017;25(102):259-266.
MyJurnal

This study presents the sensitivity of graphene nanoribbon (GNR) when exposed to ammonia gas at room temperature. Alumina were used as a substrate and coated with GNR as sensing film for ammonia gas detection. Four different concentration of GNR in the category of maximum, high, low, and minimum were prepared. Each category of GNR will be dispersed on alumina substrate with area of 1cm2 and 4cm2. 30nm of gold contacts are sputtered on both ends of the sensing film. The ammonia gas can be detected by measuring the changes in resistance. The GNR as ammonia sensor shows good responses at room temperature. In repeatability test, maximum GNR shows least variation when exposed to ammonia with the value of 1.01% (4cm2) and 2.12% (1cm2). In a sensitivity test, 0.25% to 1.00% of ammonia gas was used and tested on maximum GNR. Maximum GNR on 4cm2 substrate shows higher sensitivity as compared to 1cm2. Reaction time of GNR on ammonia gas decreased as the concentration of ammonia increased. Larger surface area of sensing element required lesser reaction time.

Matched MeSH terms: Aluminum Oxide
Fulltext Environmental and occupational health impact of bauxite mining in Malaysia: a review

Lee, K.Y., Ho, L.Y., Tan, K.H., Tham, Y.Y., Ling, S.P., Qureshi, A.M., et al.

International Medical Journal Malaysia, 2017;16(2):137-150.
MyJurnal

In the perspective of recent bauxite mining in Malaysia, this review aims to identify the potential
environmental and health impacts on miners and surrounding communities. The environmental issues of
bauxite mining include, air, water and soil pollution due to bauxite dust; leaching of bauxite into water
sources resulting in reduced soil fertility as well as affecting agricultural food products and aquatic life.
Bauxite occupational exposure affects the health of miners, and has negative consequences on the health of
surrounding communities, such as increased respiratory symptoms, contamination of drinking water, other
potential health risks from ingestion of bauxite and heavy metals, including noise-induced hearing loss and
mental stress. This review discusses the processes of bauxite mining, its constituents and residual trace
elements, and their impact on the environment and health of exposed workers and communities. It also
explores the Malaysian legal requirements and standards of occupational exposure to bauxite.

Matched MeSH terms: Aluminum Oxide
Fulltext X-ray diffraction and TGA kinetic analyses for chemical looping combustion applications

Tijani MM, Aqsha A, Mahinpey N

Data Brief, 2018 Apr;17:200-209.
PMID: 29876387 DOI: 10.1016/j.dib.2017.12.044

Synthesis and characterization of supported metal-based oxygen carriers were carried out to provide information related to the use of oxygen carriers for chemical looping combustion processes. The Cu, Co, Fe, Ni metals supported with Al2O3, CeO2, TiO2, ZrO2 were prepared using the wetness impregnation technique. Then, the X-ray Diffraction (XRD) characterization of oxidized and reduced samples was obtained and presented. The kinetic analysis using Thermogravimetric analyzer (TGA) of the synthesized samples was conducted. The kinetics of reduction reaction of all samples were estimated and explained.

Matched MeSH terms: Aluminum Oxide
Fulltext MHD convective heat transfer in a discretely heated square cavity with conductive inner block using two-phase nanofluid model

Alsabery AI, Sheremet MA, Chamkha AJ, Hashim I

Sci Rep, 2018 May 09;8(1):7410.
PMID: 29743641 DOI: 10.1038/s41598-018-25749-2

The problem of steady, laminar natural convection in a discretely heated and cooled square cavity filled by an alumina/water nanofluid with a centered heat-conducting solid block under the effects of inclined uniform magnetic field, Brownian diffusion and thermophoresis is studied numerically by using the finite difference method. Isothermal heaters and coolers are placed along the vertical walls and the bottom horizontal wall, while the upper horizontal wall is kept adiabatic. Water-based nanofluids with alumina nanoparticles are chosen for investigation. The governing parameters of this study are the Rayleigh number (103 ≤ Ra ≤ 106), the Hartmann number (0 ≤ Ha ≤ 50), thermal conductivity ratio (0.28 ≤ k w ≤ 16), centered solid block size (0.1 ≤ D ≤ 0.7) and the nanoparticles volume fraction (0 ≤ ϕ ≤ 0.04). The developed computational code is validated comprehensively using the grid independency test and numerical and experimental data of other authors. The obtained results reveal that the effects of the thermal conductivity ratio, centered solid block size and the nanoparticles volume fraction are non-linear for the heat transfer rate. Therefore, it is possible to find optimal parameters for the heat transfer enhancement in dependence on the considered system. Moreover, high values of the Rayleigh number and nanoparticles volume fraction characterize homogeneous distributions of nanoparticles inside the cavity. High concentration of nanoparticles can be found near the centered solid block where thermal plumes from the local heaters interact.

Matched MeSH terms: Aluminum Oxide
Fulltext Municipal solid waste characteristics in Taman Universiti, Skudai, Johore, Malaysia

Edward Hingha Foday Jr, Nurul As'shikin Ramli, Hairu Nabilah Ismail, Nulhazwany Abdul Malik, Hazlami Fikri Basri, Fatihah Syahirah Abdul Aziz, et al.

Journal of Advanced Research Design, 2017;38(1):13-20.
MyJurnal

Malaysia is one of the developing countries that are facing an increase population
with an increasing and significant generation of waste. Environmental problems may
arise when the solid waste management is improper. The rate of generation is
increasing and the composition is also changing as the nation becomes more
urbanized and industrialized. The objective of this study is to present the data of
municipal solid waste (MSW) generated in Taman Universiti, Skudai, Johor Bahru,
Malaysia. The composition of MSW was studied by segregating it into different
components such as food waste, paper, glass, plastics, metal and tin aluminums. It
was observed that Taman Universiti area produced around 40% plastics waste which
was the highest component compared to other waste, followed by food waste and
papers with 38.2% and 21% respectively. Meanwhile, food waste was recorded the
highest moisture content with 38.2% while glass had the lowest moisture content
with 0.4%. The reliable estimate of MSW generated is important for proper waste
management planning. These data could enhance in implementation of waste
management system in that area.

Matched MeSH terms: Aluminum
Radioluminescence sensing of radiology exposures using P-doped silica optical fibres

Bradley DA, Zubair HT, Oresegun A, Louay GT, Ariffin A, Khandaker MU, et al.

Appl Radiat Isot, 2018 Nov;141:176-181.
PMID: 29673719 DOI: 10.1016/j.apradiso.2018.02.025

In previous work we investigated the real-time radioluminescence (RL) yield of Ge-doped silica fibres and Al2O3 nanodot media, sensing electron- and x-ray energies and intensities at values familiarly obtained in external beam radiotherapy. The observation of an appreciable low-dose sensitivity has given rise to the realisation that there is strong potential for use of RL dosimetry in diagnostic radiology. Herein use has been made of P-doped silica optical fibre, 2 mm diameter, also including a 271 µm cylindrical doped core. With developing needs for versatile x-ray imaging dosimetry, preliminary investigations have been made covering the range of diagnostic x-ray tube potentials 30 kVp to 120 kVp, demonstrating linearity of RL with kVp as well as in terms of the current-time (mAs) product. RL yields also accord with the inverse-square law. Given typical radiographic-examination exposure durations from tens- to a few hundred milliseconds, particular value is found in the ability to record the influence of x-ray generator performance on the growth and decay of beam intensity, from initiation to termination.

Matched MeSH terms: Aluminum Oxide
Fulltext Preliminary study of cosmetic coloured contact lenses chemical elements analysis using energy dispersive X-ray spectroscopy

Syazwan Hafiz Mohd, Wan Elhami Wan Omar, Ai-Hong Chen

Pertanika Journal of Science & Technology, 2017;25(103):73-82.
MyJurnal

This paper examines the chemical elements used as colour additives in cosmetic coloured contact lenses (Cos-CCL) using Field Emission Scanning Electron Microscope equipped with Energy Dispersive X-ray Spectroscopy (FESEM-EDX) analysis. The samples comprised two different Cos-CCL brands and colours (sample A1-black iris colour & B1-gray iris colour) with their respective clear contact lens counterparts as controls (sample A2 & B2). The parameters of Cos-CCL were observed carefully so that they resembled their respective controls. All the samples were analysed for chemical element characterisation by using EDX spectroscopy surface mapping analysis on both front and back surfaces. EDX spectroscopy point analysis was done on cross-section surface of Cos-CCL when colour additive pattern could not be detected by FESEM on either surface. FESEM-EDX spectroscopy analysis has revealed iron element in the colour additives of the A1 sample and aluminium elements in the B2 sample. These two elements were not present in the respective control samples. It can be concluded that iron and aluminium elements are exclusively attributed to the colour additive in Cos-CCL samples. It is important for manufacturers of Cos-CCL to disclose information of their products and create greater awareness on the risks facing users.

Matched MeSH terms: Aluminum
Fulltext Mechanical behaviour and microstructure Aluminium Foam Tube Produce (AFTP) using infiltration method with vacuum-gas

Ismail Lias, Muhammad Hussain Ismail, Iskandar Dzulkernain Md Raffee, Mohd Aman Ihsan Mamat

Pertanika Journal of Science & Technology, 2017;25(103):223-232.
MyJurnal

Aluminium foam tube is a metal that consists of porous medium with special characteristics such as good energy absorption, good heat transfer and high thermal conductivity. These make it suitable to be used in a wide range of applications such as in heat exchangers. The aim of this project is to identify and analyse mechanical behaviour and microstructure aluminium foam tube produced and fabricated with infiltration method with vacuum-gas. The density of aluminium foam tube was also determined and an average aluminium foam tube with porosity 50% - 80% with the average NaCl particle size 2mm, 3mm and 4mm was produced. Foams with porosity 60%-75% NaCl has higher energy absorption. These was based on foam structure, density and maximum compressive load test result.

Matched MeSH terms: Aluminum
Fulltext Development of adjustable foot corrective device for clubfoot treatment

Shahrol Mohamaddan, Chai Siew Fu, Ahmad Hata Rasit, Siti Zawiah Md Dawal, Keith Case

Pertanika Journal of Science & Technology, 2017;25(105):251-258.
MyJurnal

Congenital talipes equinovarus (CTEV) or clubfoot is a complex deformity of the foot that is characterised by four main deformities; forefoot cavus and adductus, hindfoot varus and ankle equinus. Currently, the Ponseti method is the most general and recognized treatment with a high success rate of over 90%. The treatment involves gentle manipulation and serial casting. However, the casting method could create complications for the patients such as soft-tissue damage and inconvenience in following the treatment schedule especially for those living far away from hospital. The aim of this research is to develop an adjustable corrective device for clubfoot treatment based on the techniques in the Ponseti method and at the same time attempt to eliminate the side-effects. The prototype consists of six adjustable movements from six different mechanisms to correct the four deformities. The prototype was developed using 3D printing method and the main material used is polylactic acid (PLA), rubber, aluminium and cotton fabric with sponge. The total weight of the prototype is around 300 g.

Matched MeSH terms: Aluminum
Fulltext Preparation of NiAl2O4-Based Flexible Substrates for Metamaterials with Negative Dielectric Properties

Rahman MA, Ahamed E, Faruque MRI, Islam MT

Sci Rep, 2018 Oct 08;8(1):14948.
PMID: 30297730 DOI: 10.1038/s41598-018-33295-0

Various techniques are commonly used to produce nano-crystalline NiAl2O4 materials; however, their practical applications in the microwave region remain very limited. In this work, flexible substrates for metamaterials containing two different concentrations of NiAl2O4 (labelled Ni36 and Ni42) have been synthesised using a sol-gel method. The formation of spinel structures in the synthesised materials is confirmed, and their crystalline sizes are determined using scanning electron microscopy, X-ray diffraction, and energy dispersive X-ray techniques. The dielectric properties, conductivities, loss tangents, and other parameters of the NiAl2O4-based substrates are analysed to evaluate their applicability as dielectric materials for the microwave frequency range. The obtained results show that the fabricated Ni36 and Ni42 nickel aluminates possess dielectric constants of 4.94 and 4.97 and loss tangents of 0.01 and 0.007, respectively; in addition, they exhibit high flexibility and light weight, which make them suitable for applications as metamaterial substrates. The synthesised structures are also validated experimentally using a commercially available electromagnetic simulator; as a result, double negative behaviour of the flexible metamaterials has been observed. Furthermore, it is found that the prepared NiAl2O4 substrates can be used in the S-, C-, and X-bands of the microwave frequency region.

Matched MeSH terms: Aluminum Oxide
Fulltext Influence of alkylphosphonium modified montmorillonite to the tensile properties of PMMA composites

Abdullah, M.A.A., Mamat, M., Rusli, S.A., Kassim, A.A.

ASM Science Journal, 2018;11(101):96-104.
MyJurnal

Considering its excellent thermal stability, alkyl phosphonium surfactant: triisobutyl(methyl)phosphonium
(TIBMP) was used in this research as an intercalant for surface
modification of Na+-MMT via ion exchange process forming organomontmorillonite
(OMMT). The OMMT was then used as filler in poly(methyl methacrylate) (PMMA) via
melt intercalation technique. OMMT decomposed at a higher temperature than commercial
alkyammonium modified MMT. Exfoliated and intercalated types of nanocomposites
are obtained from PMMA/OMMTs at low and high content of OMMT loading, depending
on the space of those clay platelets had to disperse in PMMA. The ability of OMMT to
carry a certain load applied in PMMA matrix enhances the tensile strength in all composites.
TIBMP are compatible with PMMA matrix, and significantly improves the tensile
properties of PMMA composites.

Matched MeSH terms: Aluminum Silicates

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links