Spaceflight represents a complex environmental condition. Space mutagenesis breeding has achieved marked results over the years. The objective of this study is to determine the chemical changes in medicinal mushroom Ganoderma lucidum cultivated after spaceflight in 1999. Fourier transform infrared (FTIR) and two-dimensional infrared (2DIR) correlation spectroscopy were used in analysis. The sample Sx and its control Cx showed the least dissimilarities in one-dimensional FTIR spectra, but absorbance of Sx is twice as high as Cx. Sx presented a clear peak at 1648 cm in 2nd derivative spectra, which could not be detected in the Cx. The 2DIR spectra showed the intensity of Sx in the range 1800-1400 cm-1 for protein is higher than the control. The sample Sx produced some carbohydrate peaks in the area of 889 cm-1 compared with the Cx. The spaceflight set up an extreme condition and caused changes of chemical properties in G. lucidum strain.
A portable infrared spectroscopy system has been designed and developed for assessment of quality of mango fruit. This paper describes the design and development of a fruit quality grading device using reflectance mode optical sensor. The experiment was conducted to obtain the best results from the system and the device was correlated according to the measured output. In the experiment, several samples of mango fruits have been monitored for six days to study the relation how fruit quality increases with time as fruit ripens. Between the unripe mango fruit and the ripest one, a range of 3.5 V to 4.2 V was measured by the developed system. The rate of quality increase was calculated as an average of 6.7 mV per day. These results were used to correlate the final hardware and software development of the device. The results demonstrate that, portable near infrared spectroscopy is feasible for evaluating mango quality non-destructively.
An ethanolic solution of caffeine was added to an aqueous solution of metal salts and followed by adding ethanolic solution of adenine and an aqueous solution of potassium thiocyanate to give complexes with general formula [M(CA)2(Ad)X2] where CA is caffeine, Ad is adenine, X is thiocyanate ion and M is Co(II), Ni(II), Cu(II), Zn(II) and Cd(II). The resulting products were characterized using UV-visible and infrared spectroscopies. Elemental analyses were performed using C, H, N analysis and atomic absorption techniques. The magnetic susceptibility and the conductivity were also measured. The results suggested that the complexes have octahedral geometry.
To investigate and compare the effect of three analytical methods, hydrogen bromide titrimetry (HBr titrimetry), infrared spectroscopy (IR spectroscopy), and first derivative UV-spectrophotometry (FDUV-spectrophotometry) in the determination of degree of deacetylation (DD) of chitosan.
Currently, the authentication of virgin coconut oil (VCO) has become very important due to the possible adulteration of VCO with cheaper plant oils such as corn (CO) and sunflower (SFO) oils. Methods involving Fourier transform mid infrared (FT-MIR) spectroscopy combined with chemometrics techniques (partial least square (PLS) and discriminant analysis (DA)) were developed for quantification and classification of CO and SFO in VCO. MIR spectra of oil samples were recorded at frequency regions of 4000-650cm-1 on horizontal attenuated total reflectance (HATR) attachment of FTIR. DA can successfully classify VCO and that adulterated with CO and SFO using 10 principal components. Furthermore, PLS model correlates the actual and FTIR estimated values of oil adulterants (CO and SFO) with coefficient of determination (R2) of 0.999.
This paper outlines the application of chemometrics and pattern recognition tools to classify palm oil using Fourier Transform Mid Infrared spectroscopy (FT-MIR). FT-MIR spectroscopy is used as an effective analytical tool in order to categorise the oil into the category of unused palm oil and used palm oil for frying. The samples used in this study consist of 28 types of pure palm oil, and 28 types of frying palm oils. FT-MIR spectral was obtained in absorbance mode at the spectral range from 650 cm -1 to 4000 cm -1 using FT-MIR-ATR sample handling. The aim of this work is to develop fast method in discriminating the palm oils by implementing Partial Least Square Discriminant Analysis (PLS-DA), Learning Vector Quantisation (LVQ) and Support Vector Machine (SVM). Raw FT-MIR spectra were subjected to Savitzky-Golay smoothing and standardized before developing the classification models. The classification model was validated through finding the value of percentage correctly classified by test set for every model in order to show which classifier provided the best classification. In order to improve the performance of the classification model, variable selection method known as t-statistic method was applied. The significant variable in developing classification model was selected through this method. The result revealed that PLSDA classifier of the standardized data with application of t-statistic showed the best performance with highest percentage correctly classified among the classifiers.
Synthesis of carboxymethylcellulose (CMC) from natural cellulose is an important industrial process. The effect of process parameters on the synthesis process is important information for the efficiency improvement of production process. Most of the previous studies on the effect of process parameters
on the synthesis of CMC are based on the One-Factor-At-Time (OFAT); therefore, in this work, the response surface methodology (RSM) was used. Here, the cellulose was converted to CMC through
carboxymethylation process using a technique of William etherification in heterogeneous system. The process parameters studied include the solvent ratio, reaction temperature and reactant ratio (molar ratio of NaOH to SMCA). Meanwhile, the analysis and optimization of the responses of the process, degree of substitution (DS) and yield were also performed using the response surface methodology. The validity of the synthesis process was identified by the determination of CMC spectrum using the fast Fourier infrared spectrometer (FTIR). The analysis of the results shows that carboxymethylation is strongly affected by combination of process parameters studied. The results obtained also show that the optimum responses, degree of substitution (DS) is 0.87 and yield is 1.80, whereas the optimum process parameters, solvent ratio is 0.70v/v, reaction temperature at 56.03oC, and molar ratio of NaOH to SMCA at 1.00mol/mol. These findings conclude that the DS and yield of carboxymethylation of cellulose are strongly affected by the combination of the process parameters.
Baeckea frutescens or locally known as Cucur atap is used as antibacterial, antidysentery, antipyretic and diuretic agent. In Malaysia and Indonesia, they are used as an ingredient of the traditional medicine given to mothers during confinement. A three-steps infra-red (IR) macro-fingerprinting method combining conventional IR spectra, and the secondary derivative spectra with two dimensional infrared correlation spectroscopy (2D-IR) have been proved to be effective methods to examine a complicated mixture such as herbal medicines. This study investigated the feasibility of employing multi-steps IR spectroscopy in order to study the main constituents of B. frutescens and its different extracts (extracted by chloroform, ethyl acetate, methanol and aqueous in turn). The findings indicated that FT-IR and 2D-IR can provide many holistic variation rules of chemical constituents. The structural information of the samples indicated that B. frutescens and its extracts contain a large amount of flavonoids, since some characteristic absorption peaks of flavonoids, such as ∼1600cm(-1), ∼1500cm(-1), ∼1450cm(-1), and ∼1270cm(-1) can be observed. The macroscopical fingerprint characters of FT-IR and 2D-IR spectra can not only provide the information of main chemical constituents in medicinal materials and their different extracts, but also compare the components differences among the similar samples. In conclusion, the multi-steps IR macro-fingerprint method is rapid, effective, visual and accurate for pharmaceutical research.
The anticorrosion ability of a synthesized coumarin, namely 2-(coumarin-4-yloxy)acetohydrazide (EFCI), for mild steel (MS) in 1 M hydrochloric acid solution has been studied using a weight loss method. The effect of temperature on the corrosion rate was investigated, and some thermodynamic parameters were calculated. The results indicated that inhibition efficiencies were enhanced with an increase in concentration of inhibitor and decreased with a rise in temperature. The IE value reaches 94.7% at the highest used concentration of the new eco-friendly inhibitor. The adsorption of inhibitor on MS surface was found to obey a Langmuir adsorption isotherm. Scanning electron microscopy (SEM) was performed on inhibited and uninhibited mild steel samples to characterize the surface. The Density Function theory (DFT) was employed for quantum-chemical calculations such as EHOMO (highest occupied molecular orbital energy), ELUMO (lowest unoccupied molecular orbital energy) and μ (dipole moment), and the obtained results were found to be consistent with the experimental findings. The synthesized inhibitor was characterized by Fourier transform infrared (FTIR) and nuclear magnetic resonance (NMR) spectroscopic studies.
A detailed chemical study on the stem bark of Garcinia nitida has led to the isolation of five xanthones. They are 1,6-dihydroxy-5-methoxy-6,6-dimethylpyrano[2',3':2,3]-xanthone (1), inophyllin B (2), osajaxanthone (3), 3-isomangostin (4) and rubraxanthone (5). The structures of these compounds were established using mainly 1-D and 2-D NMR spectroscopy ((1)H, (13)C, DEPT, COSY, HMBC and HMQC) while molecular masses were determined via MS techniques; 1 is a new compound.
A new abietene diterpene, kaempfolienol (5S,6S,7S,9S,10S,11R,13S-abiet-8(14)-enepenta-6,7,9,11,13-ol, 1), was isolated from a rhizome extract of Kaempferia angustifolia Rosc. along with the known compounds crotepoxide, boesenboxide, zeylenol, 2'-hydroxy-4,4',6'-trimethoxychalcone, (24S)-24-methyl-5α-lanosta-9(11),25-dien-3β-ol, β-sitosterol and β-sitosterol-3-O-β-D-glucopyranoside. The structures of all compounds were elucidated on the basis of mass spectroscopic and NMR data. Zeylenol (2), the major constituent of the plant, was derivatized into diacetate, triacetate and epoxide derivatives through standard organic reactions. The cytotoxic activity of compounds 1, 2 and the zeylenol derivatives was evaluated against the HL-60, MCF-7, HT-29 and HeLa cell lines.
Some novel 2,3-dioxo-5-(substituted)-arylpyrroles have been synthesized. Among these, pyrrolidine compound 1b was converted to 2,3-dioxo-5-aryl pyrrolidine 2b. Finally a set of hydrazone derivatives was obtained from the reaction of 2b with various hydrazine salts. The structures of all the new synthesized compounds were confirmed by elemental analyses, IR and 1H-NMR spectra.
A new tetraoxygenated xanthone, daphnifolin (1,3,5-trihydroxy-4-methoxyxanthone), along with three other xanthones, were isolated from the stem bark extracts of Mesua daphnifolia. Their structures were characterized on the basis of 1D and 2D NMR spectral data.
The stem of Stephanotis floribunda afforded a new cyclic pentapeptide stephanotic acid (1), possessing a novel 6-(leucin-3'-yl) tryptophan skeleton. The structure of 1 was assigned on the basis of extensive NMR experiments and a chemical reaction and shown to be closely related to the bicyclic octapeptide moroidin (3), a toxin from Laportea moroides.
The primary motivation of developing ceramic materials using geopolymer method is to minimize the reliance on high sintering temperatures. The ultra-high molecular weight polyethylene (UHMWPE) was added as binder and reinforces the nepheline ceramics based geopolymer. The samples were sintered at 900 °C, 1000 °C, 1100 °C, and 1200 °C to elucidate the influence of sintering on the physical and microstructural properties. The results indicated that a maximum flexural strength of 92 MPa is attainable once the samples are used to be sintered at 1200 °C. It was also determined that the density, porosity, volumetric shrinkage, and water absorption of the samples also affected by the sintering due to the change of microstructure and crystallinity. The IR spectra reveal that the band at around 1400 cm-1 becomes weak, indicating that sodium carbonate decomposed and began to react with the silica and alumina released from gels to form nepheline phases. The sintering process influence in the development of the final microstructure thus improving the properties of the ceramic materials.
Biobased polymers are useful materials in substituting conventional petroleum-derived polymers because of their good properties, ready availability, and abundance in nature. This study reports a new jatropha oil-based gel polymer electrolyte (GPE) for use in dye-sensitized solar cells (DSSCs). The GPE was prepared by mixing jatropha oil-based polyurethane acrylate (PUA) with different concentrations of lithium iodide (LiI). The GPE was characterized by infrared spectroscopy, thermal analysis, lithium nuclear magnetic resonance analysis, electrochemical analysis, and photocurrent conversion efficiency. The highest room-temperature ionic conductivity of 1.88 × 10-4 S cm-1 was obtained at 20 wt % of LiI salt. Additionally, the temperature-dependent ionic conductivity of the GPE exhibited Arrhenius behavior with an activation energy of 0.42 eV and a pre-exponential factor of 1.56 × 103 S cm-1. The electrochemical stability study showed that the PUA GPE was stable up to 2.35 V. The thermal stability of the gel electrolyte showed an improvement after the addition of the salt, suggesting a strong intermolecular interaction between PUA and Li, which leads to polymer-salt complexation, as proven by Fourier transform infrared spectroscopy analysis. A DSSC has been assembled using the optimum ionic conductivity gel electrolyte which indicated 1.2% efficiency under 1 sun condition. Thus, the jatropha oil-based GPE demonstrated favorable properties that make it a promising alternative to petroleum-derived polymer electrolytes in DSSCs.
Microencapsulated paraffin wax/polyaniline was prepared using a simple in situ polymerization technique, and its performance characteristics were investigated. Weight losses of samples were determined by Thermal Gravimetry Analysis (TGA). The microencapsulated samples with 23% and 49% paraffin showed less decomposition after 330 °C than with higher percentage of paraffin. These samples were then subjected to a thermal cycling test. Thermal properties of microencapsulated paraffin wax were evaluated by Differential Scanning Calorimeter (DSC). Structure stability and compatibility of core and coating materials were also tested by Fourier transform infrared spectrophotometer (FTIR), and the surface morphology of the samples are shown by Field Emission Scanning Electron Microscopy (FESEM). It has been found that the microencapsulated paraffin waxes show little change in the latent heat of fusion and melting temperature after one thousand thermal recycles. Besides, the chemical characteristics and structural profile remained constant after one thousand thermal cycling tests. Therefore, microencapsulated paraffin wax/polyaniline is a stable material that can be used for thermal energy storage systems.
Iron and its alloy have been proposed as biodegradable metals for temporary medical implants. However, the formation of iron oxide and iron phosphate on their surface slows down their degradation kinetics in both in vitro and in vivo scenarios. This work presents new approach to tailor degradation behavior of iron by incorporating biodegradable polymers into the metal. Porous pure iron (PPI) was vacuum infiltrated by poly(lactic-co-glycolic acid) (PLGA) to form fully dense PLGA-infiltrated porous iron (PIPI) and dip coated into the PLGA to form partially dense PLGA-coated porous iron (PCPI). Results showed that compressive strength and toughness of the PIPI and PCPI were higher compared to PPI. A strong interfacial interaction was developed between the PLGA layer and the iron surface. Degradation rate of PIPI and PCPI was higher than that of PPI due to the effect of PLGA hydrolysis. The fast degradation of PIPI did not affect the viability of human fibroblast cells. Finally, this work discusses a degradation mechanism for PIPI and the effect of PLGA incorporation in accelerating the degradation of iron.
The incorporation of magnesium ions into the calcium phosphate structure is of great interest for the development of artificial bone implants. This paper investigates the preparation of magnesium-doped biphasic calcium phosphate (Mg-BCP) via sol gel method at various concentrations of added Mg. The effect of calcinations temperature (ranging from 500 degrees C to 900 degrees C) and concentrations of Mg incorporated into BCP has been studied by the aid of XRD, TGA and infrared spectroscopy (IR) in transmittance mode analysis. The study indicated that the powder was pure BCP and Mg-BCP with 100% purity and high crystallinity. The results also indicated that beta-tricalcium phosphate (beta-TCP) phase can be observed when the powder was calcined at 800 degrees C and above.