MyMedR

Displaying publications 1 - 20 of 129 in total

Abstract:

Sort:

Fulltext Mechanical and Microstructural Evaluations of Lightweight Aggregate Geopolymer Concrete before and after Exposed to Elevated Temperatures

Abdulkareem OA, Abdullah MMAB, Hussin K, Ismail KN, Binhussain M

Materials (Basel), 2013 Oct 09;6(10):4450-4461.
PMID: 28788339 DOI: 10.3390/ma6104450

This paper presents the mechanical and microstructural characteristics of a lightweight aggregate geopolymer concrete (LWAGC) synthesized by the alkali-activation of a fly ash source (FA) before and after being exposed to elevated temperatures, ranging from 100 to 800 °C. The results show that the LWAGC unexposed to the elevated temperatures possesses a good strength-to-weight ratio compared with other LWAGCs available in the published literature. The unexposed LWAGC also shows an excellent strength development versus aging times, up to 365 days. For the exposed LWAGC to the elevated temperatures of 100 to 800 °C, the results illustrate that the concretes gain compressive strength after being exposed to elevated temperatures of 100, 200 and 300 °C. Afterward, the strength of the LWAGC started to deteriorate and decrease after being exposed to elevated temperatures of 400 °C, and up to 800 °C. Based on the mechanical strength results of the exposed LWAGCs to elevated temperatures of 100 °C to 800 °C, the relationship between the exposure temperature and the obtained residual compressive strength is statistically analyzed and achieved. In addition, the microstructure investigation of the unexposed LWAGC shows a good bonding between aggregate and mortar at the interface transition zone (ITZ). However, this bonding is subjected to deterioration as the LWAGC is exposed to elevated temperatures of 400, 600 and 800 °C by increasing the microcrack content and swelling of the unreacted silicates.

Matched MeSH terms: Coal Ash
Fulltext The Effects of Various Concentrations of NaOH on the Inter-Particle Gelation of a Fly Ash Geopolymer Aggregate

Abdullah A, Hussin K, Abdullah MMAB, Yahya Z, Sochacki W, Razak RA, et al.

Materials (Basel), 2021 Feb 27;14(5).
PMID: 33673522 DOI: 10.3390/ma14051111

Aggregates can be categorized into natural and artificial aggregates. Preserving natural resources is crucial to ensuring the constant supply of natural aggregates. In order to preserve these natural resources, the production of artificial aggregates is beginning to gain the attention of researchers worldwide. One of the methods involves using geopolymer technology. On this basis, this current research focuses on the inter-particle effect on the properties of fly ash geopolymer aggregates with different molarities of sodium hydroxide (NaOH). The effects of synthesis parameters (6, 8, 10, 12, and 14 M) on the mechanical and microstructural properties of the fly ash geopolymer aggregate were studied. The fly ash geopolymer aggregate was palletized manually by using a hand to form a sphere-shaped aggregate where the ratio of NaOH/Na2SiO3 used was constant at 2.5. The results indicated that the NaOH molarity has a significant effect on the impact strength of a fly ash geopolymer aggregate. The highest aggregate impact value (AIV) was obtained for samples with 6 M NaOH molarity (26.95%), indicating the lowest strength among other molarities studied and the lowest density of 2150 kg/m3. The low concentration of sodium hydroxide in the alkali activator solution resulted in the dissolution of fly ash being limited; thus, the inter-particle volume cannot be fully filled by the precipitated gels.

Matched MeSH terms: Coal Ash
Fulltext Fly ash porous material using geopolymerization process for high temperature exposure

Abdullah MM, Jamaludin L, Hussin K, Bnhussain M, Ghazali CM, Ahmad MI

Int J Mol Sci, 2012;13(4):4388-95.
PMID: 22605984 DOI: 10.3390/ijms13044388

This paper presents the results of a study on the effect of temperature on geopolymers manufactured using pozzolanic materials (fly ash). In this paper, we report on our investigation of the performance of porous geopolymers made with fly ash after exposure to temperatures from 600 °C up to 1000 °C. The research methodology consisted of pozzolanic materials (fly ash) synthesized with a mixture of sodium hydroxide and sodium silicate solution as an alkaline activator. Foaming agent solution was added to geopolymer paste. The geopolymer paste samples were cured at 60 °C for one day and the geopolymers samples were sintered from 600 °C to 1000 °C to evaluate strength loss due to thermal damage. We also studied their phase formation and microstructure. The heated geopolymers samples were tested by compressive strength after three days. The results showed that the porous geopolymers exhibited strength increases after temperature exposure.

Matched MeSH terms: Coal Ash/chemistry*
High pressure CO2 adsorption onto Malaysian Mukah-Balingian coals: Adsorption isotherms, thermodynamic and kinetic investigations

Abunowara M, Bustam MA, Sufian S, Babar M, Eldemerdash U, Mukhtar A, et al.

Environ Res, 2023 Feb 01;218:114905.
PMID: 36442522 DOI: 10.1016/j.envres.2022.114905

CO2 sequestration into coalbed seams is one of the practical routes for mitigating CO2 emissions. The adsorption mechanisms of CO2 onto Malaysian coals, however, are not yet investigated. In this research CO2 adsorption isotherms were first performed on dry and wet Mukah-Balingian coal samples at temperatures ranging from 300 to 348 K and pressures up to 6 MPa using volumetric technique. The dry S1 coal showed the highest CO2 adsorption capacity of 1.3 mmol g-1, at 300 K and 6 MPa among the other coal samples. The experimental results of CO2 adsorption were investigated using adsorption isotherms, thermodynamics, and kinetic models. Nonlinear analysis has been employed to investigate the data of CO2 adsorption onto coal samples via three parameter isotherm equilibrium models, namely Redlich Peterson, Koble Corrigan, Toth, Sips, and Hill, and four parameter equilibrium model, namely Jensen Seaton. The results of adsorption isotherm suggested that the Jensen Seaton model described the experimental data well. Gibb's free energy change values are negative, suggesting that CO2 adsorption onto the coal occurred randomly. Enthalpy change values in the negative range established that CO2 adsorption onto coal is an exothermic mechanism. Webber's pore-diffusion model, in particular, demonstrated that pore-diffusion was the main controlling stage in CO2 adsorption onto coal matrix. The activation energy of the coals was calculated to be below -13 kJ mol-1, indicating that adsorption of CO2 onto coals occurred through physisorption. The results demonstrate that CO2 adsorption onto coal matrix is favorable, spontaneous, and the adsorbed CO2 molecules accumulate more onto coal matrix. The observations of this investigation have significant implications for a more accurate measurement of CO2 injection into Malaysian coalbed seams.

Matched MeSH terms: Coal*
Fulltext Bioavailability of zinc oxide nano particle with fly ash soil for the remediation of metals by Parthenium hysterophorus

Ahmad A, Ghufran R, Al-Hosni TK

J Environ Health Sci Eng, 2019 Dec;17(2):1195-1203.
PMID: 32030185 DOI: 10.1007/s40201-019-00434-2

To investigate the interaction of zinc oxide nanoparticles (ZnO NPs) with fly ash soil (FAS) for the reduction of metals from FAS by Parthenium hysterophorus were studied. The average accumulation of metals by P. hysterophorus stem were Fe 79.6%; Zn 88.5%; Cu 67.5%; Pb 93.6%; Ni 43.5% and Hg 39.4% at 5.5 g ZnO NP. The concentration of ZnO NP at 1.5 g did not affect the metals accumulation, however at 5.5 g ZnO NP showed highest metal reduction was 96.7% and at 10.5-15.5 g ZnO NP of 19.8%. The metal reduction rate was R
max
for Fe 16.4; Zn 21.1; Pb 41.9; Hg 19.1 was higher than Ni 6.4 and Cu 11.3 from the FAS at 5.5 g ZnO NP whereas, the reduction rate of Pb showed highest. With doses of 5.5 g ZnO NP the biomass increased upto 78%; the metal reduced upto 98.7% with the share of 100% ZnO NP from FAS. Further investigation with phytotoxicity the plant reactive oxygen species (ROS) production were affected due was mainly due to the recovery of metals from FAS (R2 = 0.99).

Matched MeSH terms: Coal Ash
Geochemical fractionation of hazardous elements in fresh and drilled weathered South African coal fly ashes

Akinyemi SA, Gitari WM, Thobakgale R, Petrik LF, Nyakuma BB, Hower JC, et al.

Environ Geochem Health, 2020 Sep;42(9):2771-2788.
PMID: 31900823 DOI: 10.1007/s10653-019-00511-3

The chemical reactions of dry-disposed ash dump, ingressed oxygen, carbon dioxide, and infiltrating rainwater affect mineralogical transformation, redistribution, and migration of chemical species. Composite samples of weathered coal fly ash taken at various depths and fresh coal fly ash were examined using organic petrographic, X-ray diffraction, X-ray fluorescence techniques, and successive extraction procedures. Results obtained show relative enrichment of glass, Al-Fe-oxides, calcite, and tridymite in the weathered CFA, but the fresh CFA is enriched in mullite, inertinite, maghemite, and ettringite. The enrichment of the weathered CFA in amorphous glass suggests higher reactivity when compared to fresh CFA. The evident depletion of soluble oxides in the weathered CFA is attributed to flushing of the soluble salts by percolating rainwater. Comparative enrichment of examined elements in water-soluble, exchangeable, reducible, and residual fractions of the weathered CFA is partly due to the slow release of adsorbed chemical species from the alumina-silicate matrix and diffusion from the deeper sections of the particles of coal fly ash. Sodium and potassium show enrichment in the oxidisable fraction of fresh CFA. The estimated mobility factor indicates mobility for Ca, Mg, Na, Se, Mo, and Sb and K, Sr, V, Cu, Cr, Se, and B in fresh and weathered CFAs, respectively.

Matched MeSH terms: Coal; Coal Ash
Environmental evaluation and nano-mineralogical study of fresh and unsaturated weathered coal fly ashes

Akinyemi SA, Gitari WM, Petrik LF, Nyakuma BB, Hower JC, Ward CR, et al.

Sci Total Environ, 2019 May 01;663:177-188.
PMID: 30711584 DOI: 10.1016/j.scitotenv.2019.01.308

Coal combustion and the disposal of combustion wastes emit enormous quantities of nano-sized particles that pose significant health concerns on exposure, particularly in unindustrialized countries. Samples of fresh and weathered class F fly ash were analysed through various techniques including X-ray fluorescence (XRF), X-ray diffraction (XRD), focused ion beam scanning electron microscopy (FIB-SEM), field-emission gun scanning electron microscopy (FE-SEM), high-resolution transmission electron microscopy (HR-TEM) coupled with energy dispersive x-ray spectroscopy (EDS), and Raman Spectroscopy. The imaging techniques showed that the fresh and weathered coal fly ash nanoparticles (CFA-NPs) are mostly spherical shaped. The crystalline phases detected were quartz, mullite, ettringite, calcite, maghemite, hematite, gypsum, magnetite, clay residues, and sulphides. The most abundant crystalline phases were quartz mixed with Al-Fe-Si-K-Ti-O-amorphous phases whereas mullite was detected in several amorphous phases of Al, Fe, Ca, Si, O, K, Mg, Mn, and P. The analyses revealed that CFA-NPs are 5-500 nm in diameter and encapsulate several potentially hazardous elements (PHEs). The carbon species were detected as 5-50 nm carbon nanoballs of graphitic layers and massive fullerenes. Lastly, the aspects of health risks related to exposure to some detected ambient nanoparticles are also discussed.

Matched MeSH terms: Coal; Coal Ash
Fulltext Engineering Properties of Waste Sawdust-Based Lightweight Alkali-Activated Concrete: Experimental Assessment and Numerical Prediction

Alabduljabbar H, Huseien GF, Sam ARM, Alyouef R, Algaifi HA, Alaskar A

Materials (Basel), 2020 Dec 02;13(23).
PMID: 33276508 DOI: 10.3390/ma13235490

Alkali activated concretes have emerged as a prospective alternative to conventional concrete wherein diverse waste materials have been converted as valuable spin-offs. This paper presents a wide experimental study on the sustainability of employing waste sawdust as a fine/coarse aggregate replacement incorporating fly ash (FA) and granulated blast furnace slag (GBFS) to make high-performance cement-free lightweight concretes. Waste sawdust was replaced with aggregate at 0, 25, 50, 75, and 100 vol% incorporating alkali binder, including 70% FA and 30% GBFS. The blend was activated using a low sodium hydroxide concentration (2 M). The acoustic, thermal, and predicted engineering properties of concretes were evaluated, and the life cycle of various mixtures were calculated to investigate the sustainability of concrete. Besides this, by using the available experimental test database, an optimized Artificial Neural Network (ANN) was developed to estimate the mechanical properties of the designed alkali-activated mortar mixes depending on each sawdust volume percentage. Based on the findings, it was found that the sound absorption and reduction in thermal conductivity were enhanced with increasing sawdust contents. The compressive strengths of the specimens were found to be influenced by the sawdust content and the strength dropped from 65 to 48 MPa with the corresponding increase in the sawdust levels from 0% up to 100%. The results also showed that the emissions of carbon dioxide, energy utilization, and outlay tended to drop with an increase in the amount of sawdust and show more the lightweight concrete to be more sustainable for construction applications.

Matched MeSH terms: Coal Ash
Fulltext Prediction of mining-induced subsidence at Barapukuria longwall coal mine, Bangladesh

Alam AKMB, Fujii Y, Eidee SJ, Boeut S, Rahim AB

Sci Rep, 2022 08 30;12(1):14800.
PMID: 36042276 DOI: 10.1038/s41598-022-19160-1

It is essential to predict the mining-induced subsidence for sustainable mine management. The maximum observed subsidence having a noticeable areal extent due to Northern Upper Panels (NUP) and Southern Lower Panels (SLP) at the Barapukuria longwall coal mine is 5.8 m and 4.2 m, respectively, after the extraction of a 10 m thick coal seam. The mining-induced subsidence was simulated by the Displacement Discontinuity Method. The numerical model considered the effects of the ground surface, mining panels, faults, and the dyke. The predicted and the observed subsidence due to the mining of NUP and SLP were compared by varying Young's modulus, and the 0.10 GPa Young's modulus was found to be the best match in the geo-environmental condition. The effects of the faults and the dyke in the calculation were negligible. Future subsidence was predicted by considering 30 m extraction of the thick coal seam as 15.7-17.5 m in NUP and 8.7-10.5 m in SLP. The vulnerable areas demarcated considering the tilt angle and extensile strain might extend up to the coal mine office area and some villages.

Matched MeSH terms: Coal
Fulltext Natural radionuclide of Po²¹⁰ in the edible seafood affected by coal-fired power plant industry in Kapar coastal area of Malaysia

Alam L, Mohamed CA

Environ Health, 2011 May 20;10:43.
PMID: 21595985 DOI: 10.1186/1476-069X-10-43

BACKGROUND: Po²¹⁰ can be accumulated in various environmental materials, including marine organisms, and contributes to the dose of natural radiation in seafood. The concentration of this radionuclide in the marine environment can be influenced by the operation of a coal burning power plant but existing studies regarding this issue are not well documented. Therefore, the aim of this study was to estimate the Po²¹⁰ concentration level in marine organisms from the coastal area of Kapar, Malaysia which is very near to a coal burning power plant station and to assess its impact on seafood consumers.
METHODS: Concentration of Po²¹⁰ was determined in the edible muscle of seafood and water from the coastal area of Kapar, Malaysia using radiochemical separation and the Alpha Spectrometry technique.
RESULTS: The activities of Po²¹⁰ in the dissolved phase of water samples ranged between 0.51 ± 0.21 and 0.71 ± 0.24 mBql⁻¹ whereas the particulate phase registered a range of 50.34 ± 11.40 to 72.07 ± 21.20 Bqkg⁻¹. The ranges of Po²¹⁰ activities in the organism samples were 4.4 ± 0.12 to 6.4 ± 0.95 Bqkg⁻¹ dry wt in fish (Arius maculatus), 45.7 ± 0.86 to 54.4 ± 1.58 Bqkg⁻¹ dry wt in shrimp (Penaeus merguiensis) and 104.3 ± 3.44 to 293.8 ± 10.04 Bqkg⁻¹ dry wt in cockle (Anadara granosa). The variation of Po²¹⁰ in organisms is dependent on the mode of their life style, ambient water concentration and seasonal changes. The concentration factors calculated for fish and molluscs were higher than the recommended values by the IAEA. An assessment of daily intake and received dose due to the consumption of seafood was also carried out and found to be 2083.85 mBqday⁻¹person⁻¹ and 249.30 μSvyr⁻¹ respectively. These values are comparatively higher than reported values in other countries. Moreover, the transformation of Po²¹⁰ in the human body was calculated and revealed that a considerable amount of Po²¹⁰ can be absorbed in the internal organs. The calculated values of life time mortality and morbidity cancer risks were 24.8 × 10⁻⁴ and 34 × 10⁻⁴ respectively which also exceeded the recommended limits set by the ICRP.
CONCLUSIONS: The findings of this present study can be used to evaluate the safety dose uptake level of seafood as well as to monitor environmental health. However, as the calculated dose and cancer risks were found to cross the limit of safety, finding a realistic way to moderate the risk is imperative.

Matched MeSH terms: Coal
Fulltext Saving primary energy consumption through exergy analysis of combine distillation and power plant

Alhassan Salami Tijani, Nazri Mohammed, Werner Witt

Scientific Research Journal, 2012;9(2):0-0.
MyJurnal

Industrial heat pumps are heat-recovery systems that allow the temperature of waste-heat stream to be increased to a higher, more efficient temperature. Consequently, heat pumps can improve energy efficiency in industrial processes as well as energy savings when conventional passive-heat recovery is not possible. In this paper, possible ways of saving energy in the chemical industry are considered, the objective is to reduce the primary energy (such as coal) consumption of power plant. Particularly the thermodynamic analyses of integrating backpressure turbine of a power plant with distillation units have been considered. Some practical examples such as conventional distillation unit and heat pump are used as a means of reducing primary energy consumption with tangible indications of energy savings. The heat pump distillation is operated via electrical power from the power plant. The exergy efficiency of the primary fuel is calculated for different operating range of the heat pump distillation. This is then compared with a conventional distillation unit that depends on saturated steam from a power plant as the source of energy. The results obtained show that heat pump distillation is an economic way to save energy if the temperature difference between the overhead and the bottom is small. Based on the result, the energy saved by the application of a heat pump distillation is improved compared to conventional distillation unit.

Matched MeSH terms: Coal
Radionuclide emissions from a coal-fired power plant

Amin YM, Khandaker MU, Shyen AK, Mahat RH, Nor RM, Bradley DA

Appl Radiat Isot, 2013 Oct;80:109-16.
PMID: 23891979 DOI: 10.1016/j.apradiso.2013.06.014

Current study concerns measurement of radioactivity levels in areas surrounding a 2420 MW thermal power plant fueled predominantly by bituminous coal. The concentrations of (226)Ra, (232)Th and (40)K in onsite bottom-ash were found to be 139 Bq/kg, 108 Bq/kg and 291 Bq/kg, respectively, the levels for these radiolnuclides in soil decreasing with distance from the power plant. At the plant perimeter the respective radionuclide concentrations were 87 Bq/kg, 74 Bq/kg and 297 Bq/kg. In a nearby town, the corresponding concentrations were 104 Bq/kg, 52 Bq/kg and 358 Bq/kg, suggestive of use of TENORM affected soils. The mean radium equivalent activities (Raeq) in soil and ash sample in the town were 205 Bq/kg and 316 Bq/kg, respectively. The Kapar plant ash/slag appears to contain a higher level of TENORM than the world average. The degree of contamination is much higher inside the town where slag has been mixed with topsoil as landfill or as simple domestic waste. For the prevailing levels of exposure and a worst case senario, the predicted committed effective dose due to ingestion and inhalation for intake durations of 1- and 30 years would be 4.2 μSv and 220 μSv, respectively.

Matched MeSH terms: Coal; Coal Ash
The influence of hazard control and prevention toward safety behaviors and safety outcomes in coal-fired power plants using PLS-SEM

Arifin K, Ali MXM, Abas A, Ahmad MA, Ahamad MA, Sahimi AS

J Safety Res, 2023 Sep;86:376-389.
PMID: 37718065 DOI: 10.1016/j.jsr.2023.07.017

INTRODUCTION: The electrical utility industry, which plays a vital role in sustaining other sectors, contributes to high occupational accident rates in the utility industries. The high accident rate shows that there has been insufficient effort made to control unsafe actions and conditions in the workplace. This study aims to examine the influence of hazard control and prevention as leading indicators of safety behaviors and outcomes in coal-fired power plants in Malaysia.
METHODS: This quantitative research was conducted by distributing survey questionnaires randomly to five coal-fired power plants in Peninsular Malaysia. A total of 340 respondents were involved in this research. Partial least squares structural equation modeling (PLS-SEM) analysis was performed using SmartPLS to validate and examine the relationship of the proposed model.
RESULTS: The results validate the construct of hazard control and prevention consisting of planning, action, managing, and verifying, while the safety outcomes construct consists of occupational accidents, fatal accidents, near misses, and lost time injuries. The results indicate that hazard control and prevention significantly relate to safety compliance, safety participation, safety motivation, and safety knowledge. Moreover, safety outcomes were influenced negatively by hazard control and prevention through safety compliance.
CONCLUSION: The model provides a better understanding of the influence of hazard control and prevention on safety behavior and outcomes.
PRACTICAL APPLICATIONS: The model can be used as guidance for practitioners and researchers in planning and implementing hazard control and prevention to improve health and safety in the workplace.

Matched MeSH terms: Coal
Fulltext Assessment of Natural Radioactivity Levels and Potential Radiological Risks of Common Building Materials Used in Bangladeshi Dwellings

Asaduzzaman K, Mannan F, Khandaker MU, Farook MS, Elkezza A, Amin YB, et al.

PLoS One, 2015;10(10):e0140667.
PMID: 26473957 DOI: 10.1371/journal.pone.0140667

The concentrations of primordial radionuclides (226Ra, 232Th and 40K) in commonly used building materials (brick, cement and sand), the raw materials of cement and the by-products of coal-fired power plants (fly ash) collected from various manufacturers and suppliers in Bangladesh were determined via gamma-ray spectrometry using an HPGe detector. The results showed that the mean concentrations of 226Ra, 232Th and 40K in all studied samples slightly exceeded the typical world average values of 50 Bq kg(-1), 50 Bq kg(-1) and 500 Bq kg(-1), respectively. The activity concentrations (especially 226Ra) of fly-ash-containing cement in this study were found to be higher than those of fly-ash-free cement. To evaluate the potential radiological risk to individuals associated with these building materials, various radiological hazard indicators were calculated. The radium equivalent activity values for all samples were found to be lower than the recommended limit for building materials of 370 Bq kg(-1), with the exception of the fly ash. For most samples, the values of the alpha index and the radiological hazard (external and internal) indices were found to be within the safe limit of 1. The mean indoor absorbed dose rate was observed to be higher than the population-weighted world average of 84 nGy h(-1), and the corresponding annual effective dose for most samples fell below the recommended upper dose limit of 1 mSv y(-1). For all investigated materials, the values of the gamma index were found to be greater than 0.5 but less than 1, indicating that the gamma dose contribution from the studied building materials exceeds the exemption dose criterion of 0.3 mSv y(-1) but complies with the upper dose principle of 1 mSv y(-1).

Matched MeSH terms: Coal Ash/analysis
Fulltext Radioactivity of 210Po in the environmental samples from Kapar, Malaysia

Asnor Azrin Sabuti, Che Abd Rahim Mohamed, Zaharudin Ahmad

Journal of Nuclear and Related Technologies, 2010;2010(1):29-39.
MyJurnal

Various environmental samples (seawater, TSS, sediment, rainwater and fly ash) from eight different stations near Kapar coastal area were analyzed. The 210 Po activity concentrations in liquid samples (seawater and rainwater) varied between 0.34 ± 0.03 mBq L-1 to 22.44 ± 0.53 mBq L-1 . Whereas the concentrations in particulate samples (TSS, sediment and fly ash) varied between 43.79 ± 2.31 Bqkg-1 to 364.48 ± 5.43 Bqkg-1 . Results also showed the radioactivity in Kapar coastal is higher than most of Malaysian coast, reaching a factor of seven. This condition is mainly due to the operation of a coal-fired power plant nearby. This study also clarify the variability of 210 Po in environment was strongly influenced from rainfall events especially during wet seasons.

Matched MeSH terms: Coal; Coal Ash
Fulltext Strength Development and Elemental Distribution of Dolomite/Fly Ash Geopolymer Composite under Elevated Temperature

Azimi EA, Abdullah MMAB, Vizureanu P, Salleh MAAM, Sandu AV, Chaiprapa J, et al.

Materials (Basel), 2020 Feb 24;13(4).
PMID: 32102345 DOI: 10.3390/ma13041015

A geopolymer has been reckoned as a rising technology with huge potential for application across the globe. Dolomite refers to a material that can be used raw in producing geopolymers. Nevertheless, dolomite has slow strength development due to its low reactivity as a geopolymer. In this study, dolomite/fly ash (DFA) geopolymer composites were produced with dolomite, fly ash, sodium hydroxide, and liquid sodium silicate. A compression test was carried out on DFA geopolymers to determine the strength of the composite, while a synchrotron Micro-Xray Fluorescence (Micro-XRF) test was performed to assess the elemental distribution in the geopolymer composite. The temperature applied in this study generated promising properties of DFA geopolymers, especially in strength, which displayed increments up to 74.48 MPa as the optimum value. Heat seemed to enhance the strength development of DFA geopolymer composites. The elemental distribution analysis revealed exceptional outcomes for the composites, particularly exposure up to 400 °C, which signified the homogeneity of the DFA composites. Temperatures exceeding 400 °C accelerated the strength development, thus increasing the strength of the DFA composites. This appears to be unique because the strength of ordinary Portland Cement (OPC) and other geopolymers composed of other raw materials is typically either maintained or decreases due to increased heat.

Matched MeSH terms: Coal Ash
Elucidating the effect of process parameters on the production of hydrogen-rich syngas by biomass and coal Co-gasification techniques: A multi-criteria modeling approach

Bahadar A, Kanthasamy R, Sait HH, Zwawi M, Algarni M, Ayodele BV, et al.

Chemosphere, 2022 Jan;287(Pt 1):132052.
PMID: 34478965 DOI: 10.1016/j.chemosphere.2021.132052

The thermochemical processes such as gasification and co-gasification of biomass and coal are promising route for producing hydrogen-rich syngas. However, the process is characterized with complex reactions that pose a tremendous challenge in terms of controlling the process variables. This challenge can be overcome using appropriate machine learning algorithm to model the nonlinear complex relationship between the predictors and the targeted response. Hence, this study aimed to employ various machine learning algorithms such as regression models, support vector machine regression (SVM), gaussian processing regression (GPR), and artificial neural networks (ANN) for modeling hydrogen-rich syngas production by gasification and co-gasification of biomass and coal. A total of 12 machine learning algorithms which comprises the regression models, SVM, GPR, and ANN were configured, trained using 124 datasets. The performances of the algorithms were evaluated using the coefficient of determination (R2), root mean square error (RMSE), mean square error (MSE), and mean absolute error (MAE). In all cases, the ANN algorithms offer superior performances and displayed robust predictions of the hydrogen-rich syngas from the co-gasification processes. The R2 of both the Levenberg-Marquardt- and Bayesian Regularization-trained ANN obtained from the prediction of the hydrogen-rich syngas was found to be within 0.857-0.998 with low prediction errors. The sensitivity analysis to determine the effect of the process parameters on the model output revealed that all the parameters showed a varying level of influence. In most of the processes, the gasification temperature was found to have the most significant influence on the model output.

Matched MeSH terms: Coal*
Fulltext Long-term succession in a coal seam microbiome during in situ biostimulation of coalbed-methane generation

Beckmann S, Luk AWS, Gutierrez-Zamora ML, Chong NHH, Thomas T, Lee M, et al.

ISME J, 2019 03;13(3):632-650.
PMID: 30323265 DOI: 10.1038/s41396-018-0296-5

Despite the significance of biogenic methane generation in coal beds, there has never been a systematic long-term evaluation of the ecological response to biostimulation for enhanced methanogenesis in situ. Biostimulation tests in a gas-free coal seam were analysed over 1.5 years encompassing methane production, cell abundance, planktonic and surface associated community composition and chemical parameters of the coal formation water. Evidence is presented that sulfate reducing bacteria are energy limited whilst methanogenic archaea are nutrient limited. Methane production was highest in a nutrient amended well after an oxic preincubation phase to enhance coal biofragmentation (calcium peroxide amendment). Compound-specific isotope analyses indicated the predominance of acetoclastic methanogenesis. Acetoclastic methanogenic archaea of the Methanosaeta and Methanosarcina genera increased with methane concentration. Acetate was the main precursor for methanogenesis, however more acetate was consumed than methane produced in an acetate amended well. DNA stable isotope probing showed incorporation of 13C-labelled acetate into methanogenic archaea, Geobacter species and sulfate reducing bacteria. Community characterisation of coal surfaces confirmed that methanogenic archaea make up a substantial proportion of coal associated biofilm communities. Ultimately, methane production from a gas-free subbituminous coal seam was stimulated despite high concentrations of sulfate and sulfate-reducing bacteria in the coal formation water. These findings provide a new conceptual framework for understanding the coal reservoir biosphere.

Matched MeSH terms: Coal/microbiology
Fulltext Dataset on leaching properties of coal ashes from Malaysian coal power plant

Beddu S, Abd Manan TSB, Zainoodin MM, Khan T, Wan Mohtar WHM, Nurika O, et al.

Data Brief, 2020 Aug;31:105843.
PMID: 32596432 DOI: 10.1016/j.dib.2020.105843

Coal combustion by-products (CCPs) (i.e. fly (FA) and bottom (BA) ashes) generated by power plants contain heavy metals. This research presents leaching properties of coal ashes (FA and BA) collected from Jimah coal-fired power station, Port Dickson, Negeri Sembilan using USEPA standard methods namely toxicity characteristic leaching procedure (TCLP), and synthetic precipitation leaching procedure (SPLP). Heavy metals like lead (Pb), zinc (Zn), copper (Cu) and arsenic (As) were quantified using atomic absorption spectrometer (AAS). The leached of heavy metals fluxes were Cu < Zn < Pb < As. As leached the most whilst indicating of possible contamination from As. Overall, the ranges of leached concentration were adhered to permissible limits of hazardous waste criteria for metal (Pb and As) and industrial effluent (Zn and Cu). The presented data has potential reuse as reference for the coal ash concrete mixed design application in construction industries.

Matched MeSH terms: Coal; Coal Ash
Interfuel substitution, hydroelectricity consumption and CO2 emissions mitigation in Malaysia: evidence from a transcendental logarithm (trans-log) cost function framework

Bello MO, Solarin SA, Yen YY

Environ Sci Pollut Res Int, 2020 May;27(14):17162-17174.
PMID: 32146676 DOI: 10.1007/s11356-020-08251-z

The main objective of this paper is to estimate the interfuel substitution elasticities between hydropower and the fossil fuels of coal and natural gas used in the generation of electricity for Malaysia. Due to the violation of the assumption behind the ordinary least squares (OLS) method on account of the correlated error terms in the system of equations, the econometrics techniques of seemingly unrelated regression (SUR) was adopted to obtain the parameter estimates using dataset that covers the period 1988 to 2016. The main finding is that there exists substantial substitution possibility between hydropower and fossil fuels in the generation of electricity for Malaysia. CO2 emissions mitigation scenarios were also conducted to explore the possible effects of substituting fossil fuels for hydropower to generate electricity. The results show that switching from high carbon-emitting fuels to renewable energy such as hydropower will substantially reduce CO2 emission and assist the country towards achieving the carbon emissions reduction targets. Policy recommendations are offered in the body of the manuscript.

Matched MeSH terms: Coal

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links