Being biodegradable and biocompatible are crucial characteristics for biomaterial used for medical and biomedical applications. Vegetable oil-based polyols are known to contribute both the biodegradability and biocompatibility of polyurethanes; however, petrochemical-based polyols were often incorporated to improve the thermal and mechanical properties of polyurethane. In this work, palm oil-based polyester polyol (PPP) derived from epoxidized palm olein and glutaric acid was reacted with isophorone diisocyanate to produce an aliphatic polyurethane, without the incorporation of any commercial petrochemical-based polyol. The effects of water content and isocyanate index were investigated. The polyurethanes produced consisted of > 90% porosity with interconnected micropores and macropores (37-1700 µm) and PU 1.0 possessed tensile strength and compression stress of 111 kPa and 64 kPa. The polyurethanes with comparable thermal stability, yet susceptible to enzymatic degradation with 7-59% of mass loss after 4 weeks of treatment. The polyurethanes demonstrated superior water uptake (up to 450%) and did not induce significant changes in pH of the medium. The chemical changes of the polyurethanes after enzymatic degradation were evaluated by FTIR and TGA analyses. The polyurethanes showed cell viability of 53.43% and 80.37% after 1 and 10 day(s) of cytotoxicity test; and cell adhesion and proliferation in cell adhesion test. The polyurethanes produced demonstrated its potential as biomaterial for soft tissue engineering applications.
Asymmetric polyphenylsulfone (PPSU) membranes were fabricated by a non-solvent induced phase inversion method. Glycerin and silica nanoparticles were added into the polymer solution to investigate their effects on the material properties and gas separation performance of prepared membranes. The morphology and structure of PPSU membranes were analyzed by scanning electron microscopy (SEM), the surface roughness of the selective layer was analyzed by atomic force microscopy (AFM), and the surface free energy was calculated based on the contact angle measurements by using various solvents. The gas separation performance of PPSU membranes was estimated by measuring the permeability of CO2 and CH4. The addition of glycerin as a nonsolvent into the polymer solution changed the cross-section structure from finger-like structure into sponge-like structure due to the delayed liquid-liquid demixing process, which was confirmed by SEM analysis. The incorporation of silica nanoparticles into PPSU membranes slightly increased the hydrophilicity, which was confirmed by water contact angle results. PPSU membrane fabricated from the polymer solution containing 10 wt.% glycerin showed the best CO2/CH4 selectivity of 3.86 and the CO2 permeability of 1044.01 Barrer. Mixed matrix PPSU membrane containing 0.1 wt.% silica nanoparticles showed the CO2/CH4 selectivity of 3.16 and the CO2 permeability of 1202.77 Barrer.
Preparation of medicinal plants for experimental purposes is an initial step and key in achieving quality research outcome. It involves extraction and determination of quality and quantity of bioactive constituents before proceeding with the intended biological testing. The primary objective of this study was to evaluate various methods used in the preparation and screening of medicinal plants in our daily research. Although the extracts, bioactive fractions, or compounds obtained from medicinal plants are used for different purposes, the techniques involved in producing them are generally the same irrespective of the intended biological testing. The major stages included in acquiring quality bioactive molecule are the selection of an appropriate solvent, extraction methods, phytochemical screening procedures, fractionation methods, and identification techniques. The nitty-gritty of these methods and the exact road map followed solely depends on the research design. Solvents commonly used in extraction of medicinal plants are polar solvent (e.g., water, alcohols), intermediate polar (e.g., acetone, dichloromethane), and nonpolar (e.g., n-hexane, ether, chloroform). In general, extraction procedures include maceration, digestion, decoction, infusion, percolation, Soxhlet extraction, superficial extraction, ultrasound-assisted, and microwave-assisted extractions. Fractionation and purification of phytochemical substances are achieved through application of various chromatographic techniques such as paper chromatography, thin-layer chromatography, gas chromatography, and high-performance liquid chromatography. Finally, compounds obtained are characterized using diverse identification techniques such as mass spectroscopy, infrared spectroscopy, ultraviolet spectroscopy, and nuclear magnetic resonance spectroscopy. Subsequently, different methods described above can be grouped and discussed according to the intended biological testing to guide young researchers and make them more focused.
Dengue fever and its fatal complications have made a comeback since its control in the 1990’s. The Flavivirus has evolved into 4 serotypes DEN 1,2,3,4 which can be passed on by the mosquitoes for 7 generations for each serotype. This communicable disease is predominantly confined to urban areas. Quick control of the spread of the disease will prevent it from becoming an epidemic. The two species mosquitoes involved have different behaviours. The Aedes aegypti is an indoor vector which breeds in clean, clear and calm freshwater. The Aedes albopictus is an outdoor breeding mosquito which breeds in stagnant waters. Surveillance of the areas prone to outbreaks is vital. One of the roles of the entomologist is to monitor the vector for resistance to the insecticides. Localities that have been subjected to recurrent outbreaks will have vector which develop resistance to the insecticides used.
Rhodococci are renowned for their great metabolic repertoire partly because of their numerous putative pathways for large number of specialized metabolites such as biosurfactant. Screening and genome-based assessment for the capacity to produce surface-active molecules was conducted on Rhodococcus sp. ADL36, a diesel-degrading Antarctic bacterium. The strain showed a positive bacterial adhesion to hydrocarbon (BATH) assay, drop collapse test, oil displacement activity, microplate assay, maximal emulsification index at 45% and ability to reduce water surface tension to < 30 mN/m. The evaluation of the cell-free supernatant demonstrated its high stability across the temperature, pH and salinity gradient although no correlation was found between the surface and emulsification activity. Based on the positive relationship between the assessment of macromolecules content and infrared analysis, the extracted biosurfactant synthesized was classified as a lipopeptide. Prediction of the secondary metabolites in the non-ribosomal peptide synthetase (NRPS) clusters suggested the likelihood of the surface-active lipopeptide production in the strain's genomic data. This is the third report of surface-active lipopeptide producers from this phylotype and the first from the polar region. The lipopeptide synthesized by ADL36 has the prospect to be an Antarctic remediation tool while furnishing a distinctive natural product for biotechnological application and research.
Manufacturing an array of high-quality metallic pattern layers on a dielectric substrate remains a major challenge in the development of flexible and 3-D frequency selective surfaces (FSS). This paper proposes an improved fabrication solution for the 3-D FSS based on water transfer printing (WTP) technology. The main advantages of the proposed solution are its ability to transform complicated 2-D planar FSS patterns into 3-D structures while improving both manufacturing quality and production costs. WTP technology makes use of water surface tension to keep the thin metallic patterns of the proposed FSS floating flat with the absence of a solid planar substrate. This feature enables these metallic FSS patterns to be transferred onto 3-D structures through a dipping process. To test the effectiveness of the proposed technique, the FSS was designed using computer simulation software Microwave Studio to obtain the numerical performance of the FSS structure. The WTP technology was then used to fabricate the proposed FSS prototype before its performance was tested experimentally. The measurement results agreed well with the numerical results, indicating the proposed manufacturing solution would support the development of complicated 3-D electronics devices, such as conformal antenna arrays and metamaterials.
Malaysia is one of the top ten countries in the world that produce freshwater ornamental fishes. This industry can offer better livelihood opportunities to many poor households. However, most of the produced ornamental fishes are alien to Malaysia. In this study, we explore the contribution of alien freshwater fishes to the income of ornamental fish store owners and their attitude towards alien freshwater fishes within Klang Valley, Malaysia. Using a structured questionnaire, we surveyed 70 pet stores out of which 54 (81.42%) store owners responded. Most of the pet store owners were male (72%), Chinese (83%), and the highest educational level was at the secondary level (79%). Most of the pet store owners reported a monthly income of RM 2001-RM 5000 (78%) and were married (73%). Using Chi-square (χ2) test, significant relationships (p < 0.05) existed between the attitude of store owners towards alien ornamental fish species versus educational level (χ2 = 16.424, p = 0.007) and contribution of alien ornamental fishes to the pet store owners' income (χ2 = 27.266, p = 0.003). Fish sales as the main income source also related significantly with the impact of fish selling business on income level (χ2 = 10.448, p = 0.007). This study showed that the ornamental fish sales contributed over half of the income (51-100%) from the businesses of store owners. Almost half of the respondents (42%) reported that alien ornamental fish was the highest contributor to their income from the ornamental fish sale. While the mismanagement of alien ornamental fishes could give various negative ecological impacts, the socio-economic benefits of these fishes cannot be denied.
Biocalcification through the use of ureolytic bacteria and biochemical activities has evolved in recent decades into a fervent resourceful effective technology suitable for soil stabilization, crack repair and bioremediation. Extensive studies have been carried out on numerous ureolytic bacterial species isolated from soils and sewage samples. However, very limited attention has been given to limestone caves with natural calcite formations as a possible source for isolation of ureolytic bacteria. In this study, bacterial isolates were recovered from limestone cave samples to determine their suitability for biocalcification. Twenty-seven morphologically distinct bacterial isolates were identified by partial 16S rRNA gene sequencing and their various genetic diversity was characterized according to their phylogenetic affiliations. Based on the molecular identification, Sporosarcina was the most abundant genus among all the ureolytic isolates, while the rest belonged to Pseudogracilibacillus and Bacillus genera. Analytical analysis on urease measurement showed that urease activities for the isolates ranged from 1·130 to 21·513 mol urea hydrolysed per minute, with isolate NB33 achieving the highest value and TSB4 achieving the lowest value. The estimated CaCO3 precipitates for the isolates ranged from 4·04 to 17·26 mg ml-1 , with isolate NB30 achieving the highest value and TSB20 achieving the lowest value. The findings in this study demonstrated that the ureolytic bacteria from limestone caves are promising bio-calcifying agents. SIGNIFICANCE AND IMPACT OF THE STUDY: Ureolytic bacteria continues to play an important role as microbial tools used in geotechnical engineering for soil biocalcification. Microbial strains with the ability to produce urease enzyme and induce calcium carbonate mineral are often isolated from soil, water and sludge samples. However, screening for these essential microbes from extreme regions such as caves are rarely investigated. In this study, native bacteria which were isolated from limestone cave samples are identified and characterized. The findings suggested that these ureolytic bacterial isolates have the potential to serve as suitable alternative microbial agents for soil strengthening and stabilization.
Supercritical carbon dioxide (SC-CO2 ) is a non-thermal technique implemented by food, pharmaceutical, and similar industries with the aim of inhibiting the microorganisms and apply effective sterilisation. Presently, limited number of studies has reported the application of SC-CO2 on fresh chicken meat. The present work therefore aimed to reveal the microbial and physicochemical quality of the SC-CO2 -treated fresh chicken meat. The fresh chicken meat was subjected to the SC-CO2 at 14 MPa and 45°C for 40 min and was stored at 4°C for 0, 3, and 7 days. The obtained results indicated that the treatment with SC-CO2 significantly decreased the total plate count and, yeast and mould count from log10 5.90 to 2.00 CFU/g and from log10 5.02 to 2.00 CFU/g at day 7 of storage, respectively. The values of pH, cooking loss, and water holding capacity were not affected by the treatment. The results revealed that the SC-CO2 -treated samples displayed harder texture, higher lightness and yellowness, and lower redness. In addition, lipid peroxidation of SC-CO2 and control samples resulted in values of 1.9 and 0.5 MDA/mg of meat at day 7 of storage time and did not significantly change in the rest of the evaluation days. In summary, the application of SC-CO2 was capable of enhancing the microbial quality and certain physicochemical attributes. However, alteration of certain parameters of SC-CO2 might enhance the overall meat quality.
This review article highlights the thermal behaviors of selected starches that were studied using differential scanning calorimetery (DSC) with data shown in various research publications. The starches of sago, potato, sweet potato, cassava, yam, and corn are included in this overview. Our examinations indicate that thermal properties are highly affected by the type of starch, its amylose/amylopectin content, and the presence of other food ingredients such as sugar, sodium chloride, water, milk, hydrocolloids, and meat. When the heating temperatures of the starches were increased, the DSC measurements also showed an increase in the temperatures of the gelatinization (onset [To ], peak [Tp ], and conclusion [Tc ]). This may be attributed to the differences in the degree of crystallinity of the starch, which provides structural stability and makes the granule more resistant to gelatinization.
Global concerns have been observed due to the outbreak and lockdown causal-based COVID-19, and hence, a global pandemic was announced by the World Health Organization (WHO) in January 2020. The Movement Control Order (MCO) in Malaysia acts to moderate the spread of COVID-19 through the enacted measures. Furthermore, massive industrial, agricultural activities and human encroachment were significantly reduced following the MCO guidelines. In this study, first, a reconnaissance survey was carried out on the effects of MCO on the health conditions of two urban rivers (i.e., Rivers of Klang and Penang) in Malaysia. Secondly, the effect of MCO lockdown on the water quality index (WQI) of a lake (Putrajaya Lake) in Malaysia is considered in this study. Finally, four machine learning algorithms have been investigated to predict WQI and the class in Putrajaya Lake. The main observations based on the analysis showed that noticeable enhancements of varying degrees in the WQI had occurred in the two investigated rivers. With regard to Putrajaya Lake, there is a significant increase in the WQI Class I, from 24% in February 2020 to 94% during the MCO month of March 2020. For WQI prediction, Multi-layer Perceptron (MLP) outperformed other models in predicting the changes in the index with a high level of accuracy. For sensitivity analysis results, it is shown that NH3-N and COD play vital rule and contributing significantly to predicting the class of WQI, followed by BOD, while the remaining three parameters (i.e. pH, DO, and TSS) exhibit a low level of importance.
Carbon nanoparticles have been widely used in various applications. However, they are commonly known to have low dispersibility and chemical inertness which limit their practical ability in medical or biological area. Some studies have been performed to modify carbon nanoparticles such as carbon nanotubes using ultraviolet (UV)-Ozone system. However, little is known on the effects of such system towards other types of carbon nanoparticles such as mesoporous hollow carbon nanoparticles (MHCNs). Thus, in this study, improvement of MHCNs physiochemical properties have been studied using UV-Ozone treatment for the first time. The treatment was conducted in water as dispersant agent at ozone flowrate of 1.0 L/min and exposure time of 45 min. SEM images observed that MHCNs morphology and surface structure remain intact after the treatment. Observations on the dispersibility of MHCNs in phosphate buffered saline (PBS) solution shows that the dispersibility was improved compared to the untreated ones. This was supported by the low Z-average and PDI values of treated MHCNs obtained at ~400 nm and 0.2, respectively when compared to the untreated MHCNs which was obtained at 970 nm and 0.417, respectively. Thermogravimetric analysis (TGA) showed an increased in weight loss of treated MHCNs at the lower temperature compared to untreated MHCNs. Results from Fourier Transform Infrared (FTIR) showed an increase number of new functional groups that includes carboxylic acid group presence at the surface of treated MHCNs which contributes to the improvement of their dispersibility, thermal properties and chemical functionality. These findings opened a new possibility of using UV-Ozone treatment to improve physicochemical properties of MHCNs for medical area such as in drug delivery application in addition to their excellent storage and carrier system.
Microalgae can use either ammonium or nitrate for its growth and vitality. However, at a certain level of concentration, ammonium nitrogen exhibits toxicity which consequently can inhibit microalgae productivity. Therefore, this study is aimed to investigate the tolerance of Tetraselmis tetrathele to high ammonium nitrogen concentrations and its effects on growth rate, photosynthetic efficiency (F v /F m ), pigment contents (chlorophyll a, lutein, neoxanthin, and β-carotene), and fatty acids production. Experiments were performed at different ammonium nitrogen concentrations (0.31-0.87 gL-1) for 6 days under a light source with an intensity of 300 μmol photons m-2 s-1 and nitrate-nitrogen source as the experimental control. The findings indicated no apparent enhancement of photosynthetic efficiency (Fv/Fm) at high levels of ammonium nitrogen (
NH
4
+
-N) for T. tetrathele within 24 h. However, after 24 h, the photosynthetic efficiency of T. tetrathele increased significantly (p < 0.05) in high concentration of
NH
4
+
-N. Chlorophyll a content in T. tetrathele grown in all of the different
NH
4
+
-N levels increased significantly compared to nitrate-nitrogen (NO3-N) treatment (p < 0.05); which supported that this microalgal could grow even in high level of
NH
4
+
-N concentrations. The findings also indicated that T. tetrathele is highly resistant to high ammonium nitrogen which suggests T. tetrathele to be used in the aquaculture industry for bioremediation purpose to remove ammonium nitrogen, thus reducing the production cost while improving the water quality.
Global childhood obesity increased more than 8-fold over 40 years, inducing a very large personal, societal, and economic burden. Effects of available treatments are less than satisfactory; therefore, effective prevention is of high priority. In this narrative review, we explore preventive opportunities. The available evidence indicates large benefits of improving nutrition and lifestyle during early life, such as promoting breast-feeding and improving the quality of infant and early childhood feeding. Promoting healthy eating patterns and limiting sugar-containing beverage consumption from early childhood onwards are of great benefit. Regular physical activity and limited sedentary lifestyle and screen time alone have limited effects but are valuable elements in effective multicomponent strategies. The home environment is important, particularly for young children, and can be improved by educating and empowering families. School- and community-based interventions can be effective, such as installing water fountains, improving cafeteria menus, and facilitating regular physical activity. Reducing obesogenic risk factors through societal standards is essential for effective prevention and limiting socioeconomic disparity; these may comprise food, drink, and physical activity standards for day cares and schools, general food quality standards, front-of-pack food labeling, taxation of unhealthy foods, restriction of food advertisements to children, and others. Effective prevention of childhood obesity is not achieved by single interventions but by integrated multicomponent approaches involving multiple stakeholders that address children, families, and societal standards. Pediatricians and their organizations should be proactive in supporting and empowering families to support their children's health, and in promoting societal measures that protect children.
According to geological history, Peninsular Malaysia and Borneo formed at different times and were once connected during Quaternary glaciations. To determine how this history has influenced phylogeography, our study examined the population genetic structure of the tropical freshwater gastropod Melanoides tuberculata across Peninsular Malaysia and Borneo using the sequences from mitochondrial DNA 16S rRNA and cytochrome oxidase subunit I genes (1168 bp). In total, 104 specimens were collected from seventeen populations. All mtDNA haplotypes were identified as belonging to two highly divergent lineages, and these lineages were almost allopatric in their distributions. Our study found that the freshwater fauna in Malaysia might be divided into four regions: northeast Peninsular Malaysia, northwest Peninsular Malaysia, south Peninsular Malaysia, and Borneo. The phylogeography of M. tuberculata in Malaysia was shaped by the landforms of Peninsular Malaysia and by the paleo-river systems in the Sunda continental shelf. In addition, our study found that these two lineages in Malaysia have invaded the globe. These results suggest that Malaysia is located in important shipping lanes throughout the world, and the populations of M. tuberculate might be widely distributed throughout the world by shipping.
Textile waste cellulose nanofibrillated fibre has been reported with excellent strength reinforcement ability in other biopolymers. In this research cellulose nanofibrilated fibre (CNF) was isolated from the textile waste cotton fabrics with combined supercritical carbon dioxide and high-pressure homogenisation. The isolated CNF was used to enhance the polylactic acid/chitin (PLA/chitin) properties. The properties enhancement effect of the CNF was studied by characterising the PLA/chitin/CNF biocomposite for improved mechanical, thermal, and morphological properties. The tensile properties, impact strength, dynamic mechanical analysis, thermogravimetry analysis, scanning electron microscopy, and the PLA/chitin/CNF biocomposite wettability were studied. The result showed that the tensile strength, elongation, tensile modulus, and impact strength improved significantly with chitin and CNF compared with the neat PLA. Furthermore, the scanning electron microscopy SEM (Scanning Electron Microscopy) morphological images showed uniform distribution and dispersion of the three polymers in each other, which corroborate the improvement in mechanical properties. The biocomposite's water absorption increased more than the neat PLA, and the contact angle was reduced. The results of the ternary blend compared with PLA/chitin binary blend showed significant enhancement with CNF. This showed that the three polymers' combination resulted in a better material property than the binary blend.
A total of eight strains of lactic acid bacteria were isolated from water kefir grains and assessed for their in vitro α-glucosidase inhibitory activity. Lactobacillus mali K8 demonstrated significantly higher inhibition as compared to the other strains, thus was selected for in vitro probiotic potential characterization, antibiotic resistance, hemolytic activity and adaptation to pumpkin fruit puree. L. mali K8 demonstrated tolerance to pH 2.5 and resisted the damaging effects of bile salts, pepsin and pancreatin, comparable to that of Lactobacillus rhamnosus GG ATCC 53103 (reference strain). Lack of hemolytic activity and susceptibility to the five standard antibiotics indicated the safety of the K8 strain. This strain showed singular properties to be used as starters in the pumpkin fruit puree fermentation. These preliminary in vitro tests indicated the safety and functionality of the K8 strain and its potential as a probiotic candidate.
The last decade has witnessed dramatic changes in global food consumption patterns mainly because of population growth and economic development. Food substitutions for healthier eating, such as swapping regular servings of meat for protein-rich crops, is an emerging diet trend that may shape the future of food systems and the environment worldwide. To meet the erratic consumer demand in a rapidly changing world where resources become increasingly scarce due largely to anthropogenic activity, the need to develop crops that benefit both human health and the environment has become urgent. Legumes are often considered to be affordable plant-based sources of dietary proteins. Growing legumes provides significant benefits to cropping systems and the environment because of their natural ability to perform symbiotic nitrogen fixation, which enhances both soil fertility and water-use efficiency. In recent years, the focus in legume research has seen a transition from merely improving economically important species such as soybeans to increasingly turning attention to some promising underutilized species whose genetic resources hold the potential to address global challenges such as food security and climate change. Pulse crops have gained in popularity as an affordable source of food or feed; in fact, the United Nations designated 2016 as the International Year of Pulses, proclaiming their critical role in enhancing global food security. Given that many studies have been conducted on numerous underutilized pulse crops across the world, we provide a systematic review of the related literature to identify gaps and opportunities in pulse crop genetics research. We then discuss plausible strategies for developing and using pulse crops to strengthen food and nutrition security in the face of climate and anthropogenic changes.
Seasonal variations in total mercury concentrations [Hg] and trophic transfer through the food web were assessed using stable isotopic tracers for the Setiu Wetlands, Terengganu. The [Hg] measured in surface sediments and biota varied inversely between wet and dry seasons. Increased rainfall and water disturbance during the wet season are suggested as the main factors releasing Hg from surface sediments and enhancing the bioavailability of Hg to biota. The elevated Hg levels associated with the leaf stage suggested that litterfall and atmospheric deposition may be the main Hg inputs into mangrove food webs. The positive relationships between log [Hg] and δ15N provided evidence for Hg biomagnification, however low trophic magnification slopes in both seasons indicated that the ecological risk of Hg in the wetland would be negligible. The [Hg] in fish and commercial crabs were below the permitted limits for human consumption.
Several aquatic macrophytes such as Colocasia esculenta, Eleocharis dulcis, Nelumbo nucifera, Sagittaria sagittifolia, Trapa bispinosa, and Typha angustifolia possessed carbohydrate mainly in their storage and reproductive parts. Starch morphology, total starch, and amylose content of these six freshwater plant species were determined. Their functional properties, i.e., starch crystallinity, thermal properties, and rheological behaviour were assessed. Large starch granules were in N. nucifera rhizome (>15 μm), medium-sized was N. nucifera seed (8-18 μm), while the rest of the starches were small starch granules (<8 μm). Shapes of the starch granules varied from oval and irregular with centric hilum to elongated granules with the eccentric hilum. Eleocharis dulcis corm starch had significantly higher total starch content (90.87%), followed by corms of C. esculenta (82.35%) and S. sagittifolia (71.71%). Nelumbo nucifera seed starch had significantly higher amylose content (71.45%), followed by T. angustifolia pollen (36.47%). In comparison, the waxy starch was in N. nucifera rhizome (7.63%), T. bispinosa seed (8.83%), C. esculenta corm (10.61%), and T. angustifolia rhizome (13.51%). Higher resistant starch was observed mostly in rhizomes of N. nucifera (39.34%)>T. angustifolia (37.19%) and corm parts of E. dulcis (37.41%)>S. sagittifolia (35.09%) compared to seed and pollen starches. The XRD profiles of macrophytes starches displayed in all the corms and N. nucifera seed had A-type crystallinity. The T. bispinosa seed had CA-type, whereas the rest of the starches exhibited CB-type crystallinity. Waxy starches of C. esculenta corm had higher relative crystallinity (36.91%) and viscosity (46.2 mPa s) than regular starches. Based on thermal properties, high-amylose of N. nucifera seed and T. angustifolia pollen resulted in higher gelatinization enthalpy (19.93 and 18.66 J g-1, respectively). Starch properties showed equally good potential as commercial starches in starch-based food production based on their starch properties and functionality.