Displaying publications 21 - 40 of 137 in total

Abstract:
Sort:
  1. Fulltext Assessment of selected herbicides and chelating agents in water using Gas Chromatography-Electron Capture Detector (GC-ECD)
    Siti Fadhilah Abd. Rahim, Normala Masrom, Muhamad Cyrill Kamal, Noor Azmi Shaharuddin, Khairul Basyar Baharudin, Norliza Abu Bakar
    Bioremediation Science and Technology Research, 2015;3(1):27-31.
    MyJurnal
    Water contamination by herbicides and chelating agents is increasing mainly due to the
    increasing agricultural activities. Water contamination by these compounds has become a
    concern due to their adverse effects to the environment and humans. Seven sampling sites of
    water sources in Selangor and Johor were chosen for the study. Contamination level of
    Mecoprop (MCCP), Nitrilotriacetic acid (NTA) and Ethylenediaminetetraacetic acid (EDTA) in
    these water body areas was determined by using Gas Chromatography-Electron Capture
    Detector (GC-ECD). Our results indicated that water samples of Sungai Melot in Selangor
    showed the highest presence of EDTA. MCCP was detected at a high level at Sungai Sarang
    Buaya, Johor while NTA showed similar level of concentration at three different sites, Ladang
    10, Ladang Sayur and Mardi, Selangor.
    Matched MeSH terms: Chromatography, Gas
  2. Chemical compositions of the rhizome oils of two Alpinia species of Malaysia
    Sirat HM, Basar N, Jani NA
    Nat Prod Res, 2011 Jun;25(10):982-6.
    PMID: 21644178 DOI: 10.1080/14786419.2010.529079
    The essential oils obtained by hydrodistillation of the rhizomes of Alpinia aquatica Rosc. syn. Alpinia melanocarpa and Alpinia malaccensis Roscoe were analysed by capillary gas chromatography and gas chromatography-mass spectrometry. Eighteen compounds, representing 98.4% of the essential oil were identified in A. aquatica rhizome oil, with β-sesquiphellandrene in 36.5% being the major constituent, while 20 compounds representing 99.7% of the rhizome oil of A. malaccensis were identified, among which methyl (E)-cinnamate (78.2%) was the major constituent.
    Matched MeSH terms: Chromatography, Gas
  3. Chemical composition and antioxidant properties of candlenut oil extracted by supercritical CO2
    Siddique BM, Ahmad A, Alkarkhi AF, Ibrahim MH, K MO
    J Food Sci, 2011 May;76(4):C535-42.
    PMID: 22417332 DOI: 10.1111/j.1750-3841.2011.02146.x
    Candlenut oil was extracted using supercritical CO(2) (SC-CO(2)) with an optimization of parameters, by the response surface methodology. The ground candlenut samples were treated in 2 different ways, that is, dried in either a heat oven (sample moisture content of 2.91%) or dried in a vacuum oven (sample moisture content of 1.98%), before extraction. An untreated sample (moisture content of 4.87%) was used as a control. The maximum percentage of oil was extracted from the heat-oven-dried sample (77.27%), followed by the vacuum-oven-dried sample (74.32%), and the untreated sample (70.12%). At an SC-CO(2) pressure of 48.26 Mpa and 60 min of extraction time, the optimal temperatures for extraction were found to be 76.4 °C, 73.9 °C, and 70.6 °C for the untreated, heat-oven-dried, and vacuum-oven-dried samples, respectively. The heat-oven-dried sample contains the highest percentage of linoleic acid, followed by the untreated and vacuum-oven-dried samples. The antiradical activity of candlenut oil corresponded to an IC(50) value of 30.37 mg/mL.
    Matched MeSH terms: Chromatography, Gas
  4. Determination of organochlorine and pyrethroid pesticides in fruit and vegetables using solid phase extraction clean-up cartridges
    Sharif Z, Man YB, Hamid NS, Keat CC
    J Chromatogr A, 2006 Sep 15;1127(1-2):254-61.
    PMID: 16857206
    A method to determine six organochlorine and three pyrethroid pesticides in grape, orange, tomato, carrot and green mustard based on solvent extraction followed by solid phase extraction (SPE) clean-up is described. The pesticides were spiked into the sample prior to analysis, extracted with ethyl acetate, evaporated and reconstituted with a solvent mixture of acetone:n-hexane (3:7). Three different sorbents (Strong Anion Exchanger/Primary Secondary Amine (SAX/PSA), Florisil and C18) were used for the clean-up step. Pesticides were eluted with 5mL of acetone:n-hexane (3:7, v/v) and determined by gas chromatography and electron-capture detection (GC-ECD). SAX/PSA was the sorbent, which provided chromatograms with less interference and the mean recoveries obtained were within 70-120% except for captafol. The captafol recoveries for grape were within acceptable range with C18 clean-up column.
    Matched MeSH terms: Chromatography, Gas/instrumentation; Chromatography, Gas/methods*
  5. A practical approach for linearity assessment of calibration curves under the International Union of Pure and Applied Chemistry (IUPAC) guidelines for an in-house validation of method of analysis
    Sanagi MM, Nasir Z, Ling SL, Hermawan D, Ibrahim WA, Naim AA
    J AOAC Int, 2010 10 7;93(4):1322-30.
    PMID: 20922968
    Linearity assessment as required in method validation has always been subject to different interpretations and definitions by various guidelines and protocols. However, there are very limited applicable implementation procedures that can be followed by a laboratory chemist in assessing linearity. Thus, this work proposes a simple method for linearity assessment in method validation by a regression analysis that covers experimental design, estimation of the parameters, outlier treatment, and evaluation of the assumptions according to the International Union of Pure and Applied Chemistry guidelines. The suitability of this procedure was demonstrated by its application to an in-house validation for the determination of plasticizers in plastic food packaging by GC.
    Matched MeSH terms: Chromatography, Gas/methods*
  6. Comparison of signal-to-noise, blank determination, and linear regression methods for the estimation of detection and quantification limits for volatile organic compounds by gas chromatography
    Sanagi MM, Ling SL, Nasir Z, Hermawan D, Ibrahim WA, Abu Naim A
    J AOAC Int, 2010 2 20;92(6):1833-8.
    PMID: 20166602
    LOD and LOQ are two important performance characteristics in method validation. This work compares three methods based on the International Conference on Harmonization and EURACHEM guidelines, namely, signal-to-noise, blank determination, and linear regression, to estimate the LOD and LOQ for volatile organic compounds (VOCs) by experimental methodology using GC. Five VOCs, toluene, ethylbenzene, isopropylbenzene, n-propylbenzene, and styrene, were chosen for the experimental study. The results indicated that the estimated LODs and LOQs were not equivalent and could vary by a factor of 5 to 6 for the different methods. It is, therefore, essential to have a clearly described procedure for estimating the LOD and LOQ during method validation to allow interlaboratory comparisons.
    Matched MeSH terms: Chromatography, Gas
  7. Multiple use of waste catalysts with and without regeneration for waste polymer cracking
    Salmiaton A, Garforth AA
    Waste Manag, 2011 Jun;31(6):1139-45.
    PMID: 21324661 DOI: 10.1016/j.wasman.2011.01.025
    Waste plastics contain a substantial number of valuable chemicals. The wastes from post-consumer as well as from industrial production can be recycled to valuable chemical feedstock, which can be used in refineries and/or petrochemical industries. This chemical recycling process is an ideal approach in recycling the waste for a better environment. Polymer cracking using a laboratory fluidized bed reactor concentrated on the used highly contaminated catalyst, E-Cat 2. Even though E-Cat 2 had low activity due to fewer acid sites, the products yielded were similar with amorphous ASA and were far better than thermal cracking. The high levels of heavy metals, namely nickel and vanadium, deposited during their lifetime as an FCC catalyst, did not greatly affect on the catalyst activity. It was also shown that E-Cat 2 could be used with and without regeneration. Although there was more deactivation when there was no regeneration step, the yield of gases (C(2)-C(7)) remained fairly constant. For the first time, these results indicate that "waste" FCC catalyst (E-Cat) is a good candidate for future feedstock recycling of polymer waste. The major benefits of using E-Cat are a low market price, the ability to tolerate reuse and regeneration capacity.
    Matched MeSH terms: Chromatography, Gas
  8. A review of gas chromatographic techniques for identification of aqueous amine degradation products in carbonated environments
    Saeed IM, Mazari SA, Alaba P, Ali BS, Jan BM, Basirun WJ, et al.
    Environ Sci Pollut Res Int, 2021 Feb;28(6):6324-6348.
    PMID: 33398750 DOI: 10.1007/s11356-020-11753-5
    Degradation of amines is a significant issue allied to amine-based carbon dioxide (CO2) absorption in post-combustion CO2 capture. It becomes essential to have a detailed understanding of degradation products for advanced post-combustion CO2 capture technology. Identification and quantification of degradation products of amines help in practicability and environmental assessment of amine-based technology. Gas, liquid, and ion chromatographic techniques are the benchmark tools for qualitative and quantitative analyses of the amines and their derivatives. Among others, gas chromatography has been more in use for this specific application, especially for the identification of degradation products of amines. This review focuses on the critical elucidation of gas chromatographic analysis and development of methods to determine the amine degradation products, highlighting preparation methods for samples and selecting columns and detectors. The choice of detector, column, sample preparation, and method development are reviewed in this manuscript, keeping in view the industry and research applications. Furthermore, obtained results on the quantitative and qualitative analyses using gas chromatography are summarized with future perspectives.
    Matched MeSH terms: Chromatography, Gas
  9. Magnetized graphene layers synthesized on the carbon nanofibers as novel adsorbent for the extraction of polycyclic aromatic hydrocarbons from environmental water samples
    Rezvani-Eivari M, Amiri A, Baghayeri M, Ghaemi F
    J Chromatogr A, 2016 Aug 16.
    PMID: 27578405 DOI: 10.1016/j.chroma.2016.08.034
    The application of magnetized graphene (G) layers synthesized on the carbon nanofibers (CNFs) (m-G/CNF) was investigated as novel adsorbent for the magnetic solid-phase extraction (MSPE) of polycyclic aromatic hydrocarbons (PAHs) in water samples followed by gas chromatography-flame ionization detector (GC-FID). Six important parameters, affecting the extraction efficiency of PAHs, including: amount of adsorbent, adsorption and desorption times, type and volume of the eluent solvent and salt content of the sample were evaluated. The optimum extraction conditions were obtained as: 5min for extraction time, 20mg for sorbent amount, dichloromethane as desorption solvent, 1mL for desorption solvent volume, 5min for desorption time and 15% (w/v) for NaCl concentration. Good performance data were obtained at the optimized conditions. The calibration curves were linear over the concentration ranges from 0.012 to 100ngmL(-1) with correlation coefficients (r) between 0.9950 and 0.9967 for all the analytes. The limits of detection (LODs, S/N=3) of the proposed method for the studied PAHs were 0.004-0.03ngmL(-1). The relative standard deviations (RSDs) for five replicates at two concentration levels (0.1 and 50ngmL(-1)) of PAHs were ranged from 3.4 to 5.7%. Appropriate relative recovery values, in the range of 95.5-99.9%, were also obtained for the real water sample analysis.
    Matched MeSH terms: Chromatography, Gas
  10. New magnetic graphene-based inorganic-organic sol-gel hybrid nanocomposite for simultaneous analysis of polar and non-polar organophosphorus pesticides from water samples using solid-phase extraction
    Rashidi Nodeh H, Wan Ibrahim WA, Kamboh MA, Sanagi MM
    Chemosphere, 2017 Jan;166:21-30.
    PMID: 27681257 DOI: 10.1016/j.chemosphere.2016.09.054
    A new graphene-based tetraethoxysilane-methyltrimethoxysilane sol-gel hybrid magnetic nanocomposite (Fe3O4@G-TEOS-MTMOS) was synthesised, characterized and successfully applied in magnetic solid-phase extraction (MSPE) for simultaneous analysis of polar and non-polar organophosphorus pesticides from several water samples. The Fe3O4@G-TEOS-MTMOS nanocomposite was characterized using Fourier transform-infrared spectroscopy, energy-dispersive X-ray spectroscopy, field emission scanning electron microscopy and X-ray diffraction. Separation, determination and quantification were achieved using gas chromatography coupled with micro electron capture detector. Adsorption capacity of the sorbent was calculated using Langmuir equation. MSPE was linear in the range 100-1000 pg mL(-1) for phosphamidon and dimethoate, and 10-100 pg mL(-1) for chlorpyrifos and diazinon, with limit of detection (S/N = 3) of 19.8, 23.7, 1.4 and 2.9 pg mL(-1) for phosphamidon, dimethoate, diazinon and chlorpyrifos, respectively. The LODs obtained is well below the maximum residual level (100 pg mL(-1)) as set by European Union for pesticides in drinking water. Acceptable precision (%RSD) was achieved for intra-day (1.3-8.7%, n = 3) and inter-day (7.6-17.8%, n = 15) analyses. Fe3O4@G-TEOS-MTMOS showed high adsorption capacity (54.4-76.3 mg g(-1)) for the selected OPPs. No pesticide residues were detected in the water samples analysed. Excellent extraction recoveries (83-105%) were obtained for the spiked OPPs from tap, river, lake and sea water samples. The newly synthesised Fe3O4@G-TEOS-MTMOS showed high potential as adsorbent for OPPs analysis.
    Matched MeSH terms: Chromatography, Gas
  11. New macroporous β-cyclodextrin functionalized ionic liquid polymer as an adsorbent for solid phase extraction with phenols
    Raoov M, Mohamad S, bin Abas MR, Surikumaran H
    Talanta, 2014 Dec;130:155-63.
    PMID: 25159393 DOI: 10.1016/j.talanta.2014.06.067
    Cyclodextrin-ionic liquid polymer (βCD-BIMOTs-TDI) is a new class of macroporous material and has great potential to be used as an SPE adsorbent material for extraction of phenols in river water samples. Six phenols, as model analytes, were extracted on a βCD-BIMOTs-TDI SPE cartridge, and then, eluted with 2 mL of methanol containing 1% acetic acid. The optimum experimental condition was 15 mL of sample volume (sample at pH 6) and 2 mL of methanol containing 1% acetic acid as an eluent solvent. The eluent concentration was determined by using Gas Chromatography-Flame Ionization Detector (GC-FID). Under optimized condition, high sensitivity (detection limits 0.23-0.35 µg/L) and good recoveries (87-116%) were achieved with satisfactory relative standard deviation (RSD) (0.1-1.7%). The developed βCD-BIMOTs-TDI-SPE was then compared with other adsorbents, and the obtained results showed that the βCD-BIMOTs-TDI exhibited higher extraction recovery due to the unique structure and properties. Finally, the βCD-BIMOTs-TDI was applied as a solid phase extraction sorbent for phenols determination under optimized condition, in river and tap waters, prior to the GC-FID separation.
    Matched MeSH terms: Chromatography, Gas
  12. Palm-Based Neopentyl Glycol Diester: A Potential Green Insulating Oil
    Raof NA, Yunus R, Rashid U, Azis N, Yaakub Z
    Protein Pept Lett, 2018;25(2):171-179.
    PMID: 29359647 DOI: 10.2174/0929866525666180122095056
    BACKGROUND: The transesterification of high oleic palm oil methyl ester (HOPME) with neopentyl glycol (NPG) has been investigated. The present study revealed the application of low-pressure technology as a new synthesis method to produce NPG diesters. Single variable optimization and response surface methodology (RSM) were implemented to optimize the experimental conditions to achieve the maximum composition (wt%) of NPG diesters.

    OBJECTIVE: The main objective of this study was to optimize the production of NPG diesters and to characterize the optimized esters with typical chemical, physical and electrical properties to study its potential as insulating oil.

    METHODS: The transesterification reaction between HOPME and NPG was conducted in a 1L three-neck flask reactor at specified temperature, pressure, molar ratio and catalyst concentration. For the optimization, four factors have been studied and the diester product was characterized by using gas chromatography (GC) analysis. The synthesized esters were then characterized with typical properties of transformer oil such as flash point, pour point, viscosity and breakdown voltage and were compared with mineral insulating oil and commercial NPG dioleate. For formulation, different samples of NPG diesters with different concentration of pour point depressant were prepared and each sample was tested for its pour point measurement.

    RESULTS: The optimum conditions inferred from the analyses were: molar ratio of HOPME to NPG of 2:1.3, temperature = 182°C, pressure = 0.6 mbar and catalyst concentration of 1.2%. The synthesized NPG diesters showed very important improvement in fire safety compared to mineral oil with flash point of 300°C and 155°C, respectively. NPG diesters also exhibit a relatively good viscosity of 21 cSt. The most striking observation to emerge from the data comparison with NPG diester was the breakdown voltage, which was higher than mineral oil and definitely in conformance to the IEC 61099 limit at 67.5 kV. The formulation of synthesized NPD diesters with VISCOPLEX® pour point depressant has successfully increased the pour point of NPG diester from -14°C to -48°C.

    CONCLUSION: The reaction time for the transesterification of HOPME with NPG to produce NPG diester was successfully reduced to 1 hour from the 14 hours required in the earlier synthesis method. The main highlight of this study was the excess reactant which is no longer methyl ester but the alcohol (NPG). The optimum reaction conditions for the synthesis were molar ratio of 2:1.13 for NPG:HOPME, 182°C, 0.6 mbar and catalyst concentration of 1.2 wt%. The maximum NPG diester yield of 87 wt% was consistent with the predicted yield of 87.7 wt% obtained from RSM. The synthesized diester exhibited better insulating properties than the commercial products especially with regards to the breakdown voltage, flash point and moisture content.

    Matched MeSH terms: Chromatography, Gas
  13. Fulltext Cerebrospinal fluid lactic acid concentration in bacterial meningitis
    Pit S, Jamal F, Isahak I, Minhaj AA
    Med J Malaysia, 1987 Dec;42(4):302-5.
    PMID: 3454403
    Lactic acid concentration was determined in 37 specimens of cerebrospinal fluid by gas liquid chromatography. It was found to be raised (30 mg/dl) in 15 specimens from culture positive cases of bacterial meningitis and one of fungal meningitis. It was < 30 mg/dl in cerebrospinal fluid from four cases of viral meningoencephalitis and 10 contaminated specimens. It was also raised in two specimens from culture negative cases. Determination of cerebrospinal fluid lactic acid concentration by gas liquid chromatography provides a useful, additional test in the diagnosis of bacterial meningitis
    Matched MeSH terms: Chromatography, Gas
  14. Fulltext Intrastrain comparison of the chemical composition and antioxidant activity of an edible mushroom, Pleurotus giganteus, and its potent neuritogenic properties
    Phan CW, David P, Tan YS, Naidu M, Wong KH, Kuppusamy UR, et al.
    ScientificWorldJournal, 2014;2014:378651.
    PMID: 25121118 DOI: 10.1155/2014/378651
    Two strains of Pleurotus giganteus (commercial and wild) were tested for their ability to induce neurite outgrowth in rat pheochromocytoma (PC12) and mouse neuroblastoma-2a (N2a) cells. Treatment with the mushroom extracts resulted in neuronal differentiation and neuronal elongation, but not nerve growth factor (NGF) production. Linoleic acid (4.5-5.0%, w/w) which is a major fatty acid present in the ethanol extract promoted NGF biosynthesis when augmented with low concentration of NGF (5 ng/mL). The two strains of mushroom were found to be high in protein (154-192 g kg(-1)), total polysaccharides, phenolics, and flavonoids as well as vitamins B1, B2, and B3. The total phenolics present in the mushroom extracts were positively correlated to the antioxidant activity (free radical scavenging, ferric reducing power, and lipid peroxidation inhibition). To conclude, P. giganteus could potentially be used in well-balanced diet and as a source of dietary antioxidant to promote neuronal health.
    Matched MeSH terms: Chromatography, Gas
  15. Pregnenolone metabolites in rat testis: endogenous concentrations, and intracellular distribution in whole testes during incubation in vitro
    Pertiwi AK, Kwan TK, Gower DB
    J Steroid Biochem Mol Biol, 2002 Aug;81(4-5):363-7.
    PMID: 12361726
    The intracellular movements of pregnenolone in rat testes were investigated. Whole testes were incubated in the presence or absence of pregnenolone (2.5mM) in the medium for 120 min (in some studies 30, 60, and 90 min). The testes were homogenised, subcellular fractions prepared and analysed in quadruplicate for steroid content by gas chromatography-mass spectrometry with selected ion monitoring. Quantification of pregnenolone and 11 of its metabolites, obtained from non-incubated whole testes, provided values for endogenous amounts. Pregnenolone was the only steroid of quantitative importance found initially in the mitochondrial fraction but was subsequently found in the microsomal fraction, where metabolism occurred. Identification and quantification of metabolites indicated that both classical pathways for testosterone production were operating, with the 4-en-3-oxosteroid pathway predominating. By 120 min, virtually all pregnenolone metabolites, including pregnenolone itself, were found in the cytosol, consistent with an overall movement from mitochondria to endoplasmic reticulum to cytosol.
    Matched MeSH terms: Chromatography, Gas
  16. Fulltext Data on organochlorine concentration levels in soil of lowland paddy field, Kelantan, Malaysia
    Osman BE, Khalik WMAWM
    Data Brief, 2018 Oct;20:999-1003.
    PMID: 30225314 DOI: 10.1016/j.dib.2018.08.178
    The main goal of this research work is to measure the concentration levels of organochlorine residue in soil. The potential health risk of this pollutant on human was also determined. 10 samples were taken from a lowland paddy field situated in Kelantan, Malaysia. Physical parameters namely soil pH, organic carbon content, water content and particle size were identified to evaluate the quality of soil from the agriculture site. Soxhlet extraction and florisil clean-up process were applied to isolate 10 targeted organochlorine compounds prior to the final determination using a gas chromatography-electron capture detector. Soil from the lowland has characteristics such as slightly acidic, low organic carbon content, high water content and texture dominated by the sandy type. Concentration levels of six detected organochlorine pesticides were calculated in µg/kg. Hazard quotient value in all samples was less than the acceptable risk level HQ ≤ 1, thus reflecting the status of soil in the subjected area as unlikely to pose any adverse health effects.
    Matched MeSH terms: Chromatography, Gas
  17. Fulltext Characterization of agarwood incense using gas chromatography - mass spectrometry (GC-MS) coupled with Solid Phase Micro Extraction (SPME) and Gas Chromatography - Flame Ionization Detector (GC-FID)
    Nurlaila Ismail, Mohd Hezri Fazalul Rahiman, Mohd Nasir Taib, Mastura Ibrahim, Seema Zareen, Saiful Nizam Tajuddin
    Scientific Research Journal, 2015;12(2):0-0.
    MyJurnal
    This paper presents the application of Solid Phase Micro Extraction (SPME) coupled with Gas Chromatography - Mass Spectrometry (GC-MS) and Gas Chromatography - Flame Ionization Detector (GC-FID) in characterizing the agarwood incense. The work involved three types of SPME fibres at 30 minute sampling time. The fibres are 50/30 μm divinylbenzene-carboxen-polydimethysiloxane (DVB-CAR-PDMS), 65 μm polydi methylsiloxane-divinylbenzene (PDMS-DVB) and 85 μm carboxen-polydimethyl siloxane (CAR-PDMS). The results showed that among the many compounds extracted by GC-MS coupled with SPME, six compounds were substantially found in high quality agarwood incense due to their high percentage area (%). They are β-maaliene, α-elemol, β-selinene, 10-epi-γ-eudesmol, agarospirol and caryophellene oxide. The finding offers a new approach for establishing the volatile profile of agarwood incense components as well as for agarwood grading and discrimination.
    Matched MeSH terms: Chromatography, Gas
  18. Production of biodiesel from palm fatty acid distillate by microwave-assisted sulfonated glucose acid catalyst
    Nur Nazlina Saimon, Heng Khuan Eu, Anwar Johari, Norzita Ngadi, Mazura Jusoh, Zaki Yamani Zakaria
    Sains Malaysiana, 2018;47:109-115.
    Biodiesel, one of the renewable energy sources has gained attention for decades as the alternative fuel due to its remarkable properties. However, there are several drawbacks from the industrial production of biodiesel such as the spike in the production cost, environmental issues related to the usage of homogeneous catalyst and profitability in long term. One of the solutions to eliminate the problem is by utilizing low cost starting material such as palm fatty acid distillate (PFAD). PFAD is a byproduct from the refining of crude palm oil and abundantly available. Esterification of PFAD to biodiesel will be much easier with the presence of heterogeneous acid catalyst. Most of acid catalyst preparation involves series of heating process using conventional method. In this study, microwave was utilized in catalyst preparation, significantly reducing the reaction time from conventional heating method. The catalyst produced was characterized using X-Ray Diffraction (XRD), Brunauer Emmet and Teller (BET), Scanning Electron Microscopy (SEM), Temperature-Programmed Desorption - Ammonia (TPD-NH3) and Fourier Transform Infrared (FTIR) while percentage yield and conversion of the PFAD were analysed by gas chromatography - flame ionization detector (GC-FID) and acid-base titration, respectively. It has been demonstrated that the percentage yield of biodiesel from the PFAD by employing sulfonated glucose acid catalyst (SGAC) reached 98.23% under the following conditions: molar ratio of methanol to PFAD of 10:1, catalyst loading of 2.5% and reaction temperature of 70oC. The microwave-assisted SGAC showed its potential to replace the SGAC produced via conventional heating method.
    Matched MeSH terms: Chromatography, Gas
  19. Fulltext Surface Energy Mapping of Modified Silica Using IGC Technique at Finite Dilution
    Ngeow YW, Williams DR, Chapman AV, Heng JYY
    ACS Omega, 2020 May 12;5(18):10266-10275.
    PMID: 32426583 DOI: 10.1021/acsomega.9b03920
    The reinforcing silica filler, which can be more than 40% of an elastomer composite, plays a key role to achieve the desired mechanical properties in elastomer vulcanizates. However, the highly hydrophilic nature of silica surface causes silica particle aggregation. It remained a challenge for many tire manufacturers when using silica-filled elastomer compounds. Here, the silica surface energy changes when the surface is modified with coupling or noncoupling silanes; coupling silanes can covalently bond the silica to the elastomers. The surface energy of silica was determined using inverse gas chromatography (IGC) at finite dilution (FD-IGC) and found to be reduced by up to 50% when the silica surface was silanized. The spatial distribution of silica aggregates within the tire matrix is determined by transmission electron microscopy (TEM) and a direct correlation between aggregate size (silica microdispersion) and work of cohesion from IGC is reported, highlighting surface energy and work of cohesion being excellent indicators of the degree of dispersion of silica aggregates.
    Matched MeSH terms: Chromatography, Gas
  20. Fulltext Fatty acid composition of five Malaysian biscuits (cream crackers) with special reference to trans-fatty acids
    Neo, Y.P., Tan, C.H., Ariffin, A.
    International Food Research Journal, 2007;14(3):197-204.
    MyJurnal
    The fatty acid composition and trans fatty acids (TFA) contents of samples of five Malaysian cream crackers biscuit brands were determined by gas-liquid chromatography, using a 60 m Supelco SP2340 fused silica capillary column and flame ionization detection. The identities of the fatty acids were established by comparing their retention times with authentic standards from Supelco. The results were expressed as relative percentages. The total saturated fatty acids (SFA) in the samples ranged from 48.90% to 54.87% of total fatty acids. As for the polyunsaturated fatty acids (PUFA), the total PUFA in the samples ranged from 9.97% to 11.73% of total fatty acids. Total trans fatty acids (TFA) ranged from 0.17% to 0.77% of total fatty acids. The monotrans 18:2 tc or 18:2 ct isomer content ranged from 0.07% to 0.10% of total fatty acids and the ditrans 18:2 isomer (9t, 12t) was not detected. The results indicate that all the fat sources of the 5 sample crackers biscuit brands were palm oil based.
    Matched MeSH terms: Chromatography, Gas
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links