MyMedR

Displaying publications 521 - 540 of 1243 in total

Abstract:

Sort:

Iminodiacetic acid modified kenaf fiber for waste water treatment

Razak MR, Yusof NA, Haron MJ, Ibrahim N, Mohammad F, Kamaruzaman S, et al.

Int J Biol Macromol, 2018 Jun;112:754-760.
PMID: 29428390 DOI: 10.1016/j.ijbiomac.2018.02.035

In the present study, iminodiacetic acid (IDA)-modified kenaf fiber, K-IDA formed by the chemical modification of plant kenaf biomass was tested for its efficacy as a sorbent material towards the purification of waste water. The K-IDA fiber was first characterized by the instrumental techniques like Fourier transform infrared (FTIR) analysis, elemental analysis (CHNSO), and scanning electron microscopy (SEM). On testing for the biosorption, we found that the K-IDA has an increment in the adsorption of Cu2+ ions as compared against the untreated fiber. The Cu2+ ions adsorption onto K-IDA fits very well with the Langmuir model and the adsorption maximum achieved to be 91.74mg/g. Further, the adsorption kinetics observed to be pseudo second-order kinetics model and the Cu2+ ions adsorption is a spontaneous endothermic process. The desorption study indicates a highest percentage of Cu2+ of 97.59% from K-IDA under 1M HCl solution against H2SO4 (72.59%) and HNO3 (68.66%). The reusability study indicates that the efficiency did not change much until the 4th cycle and also providing enough evidence for the engagement of our biodegradable K-IDA fiber towards the removal of Cu2+ ions in real-time waste water samples obtained from the electroplating and wood treatment industries.

Matched MeSH terms: Hydrogen-Ion Concentration
Novel synergistic hydrous iron-nickel-manganese (HINM) trimetal oxide for hazardous arsenite removal

Nasir AM, Goh PS, Ismail AF

Chemosphere, 2018 Jun;200:504-512.
PMID: 29501887 DOI: 10.1016/j.chemosphere.2018.02.126

A novel hydrous iron-nickel-manganese (HINM) trimetal oxide was successfully fabricated using oxidation and coprecipitation method for metalloid arsenite removal. The atomic ratio of Fe:Ni:Mn for this adsorbent is 3:2:1. HINM adsorbent was identified as an amorphous nanosized adsorbent with particle size ranged from 30 nm to 60 nm meanwhile the total active surface area and pore diameter of HINM area of 195.78 m2/g and 2.43 nm, respectively. Experimental data of arsenite adsorption is best fitted into pseudo-second order and Freundlich isotherm model. The maximum adsorption capacity of arsenite onto HINM was 81.9 mg/g. Thermodynamic study showed that the adsorption of arsenite was a spontaneous and endothermic reaction with enthalpy change of 14.04 kJ/mol and Gibbs energy of -12 to -14 kJ/mol. Zeta potential, thermal gravimetric (TGA) and Fourier transform infrared (FTIR) analysis were applied to elucidate the mechanism of arsenite adsorption by HINM. Mechanism of arsenite adsorption by HINM involved both chemisorption and physisorption based on the electrostatic attraction between arsenite ions and surface charge of HINM. It also involved the hydroxyl substitution by arsenite ions through the formation of inner-sphere complex. Reusability of HINM trimetal oxide was up to 89% after three cycles of testing implied that HINM trimetal oxide is a promising and practical adsorbent for arsenite.

Matched MeSH terms: Hydrogen-Ion Concentration
Synthesis and characterization of cotton fiber-based nanocellulose

Theivasanthi T, Anne Christma FL, Toyin AJ, Gopinath SCB, Ravichandran R

Int J Biol Macromol, 2018 Apr 01;109:832-836.
PMID: 29133091 DOI: 10.1016/j.ijbiomac.2017.11.054

Nanocellulose prepared from the natural material has a promising wide range of opportunities to obtain the superior material properties towards various end-products. In this research, commercially available natural cotton was treated with aqueous sodium hydroxide solution to eliminate the hemicellulose and lignin, then cellulose was collected. The collected cellulose was subjected to acid hydrolysis using sulfuric acid to obtain nanocellulose. The prepared nanocellulose was further characterized with the aid of Fourier transform infrared spectroscopy, X-ray diffraction and Scanning Electron Microscopy to elucidate the chemical structure, crystallinity and the morphology.

Matched MeSH terms: Hydrogen-Ion Concentration
Fulltext Effects of dietary supplementation of leaves and whole plant of Andrographis paniculata on rumen fermentation, fatty acid composition and microbiota in goats

Yusuf AL, Adeyemi KD, Samsudin AA, Goh YM, Alimon AR, Sazili AQ

BMC Vet Res, 2017 Nov 24;13(1):349.
PMID: 29178910 DOI: 10.1186/s12917-017-1223-0

BACKGROUND: The nature and amount of dietary medicinal plants are known to influence rumen fermentation and nutrient digestibility in ruminants. Nonetheless, changes in nutrient digestibility and rumen metabolism in response to dietary Andrographis paniculata (AP) in goats are unknown. This study examined the effects of dietary supplementation of leaves and whole plant of AP on nutrient digestibility, rumen fermentation, fatty acids and rumen microbial population in goats. Twenty-four Boer crossbred bucks (4 months old; average body weight of 20.18 ± 0.19 kg) were randomly assigned to three dietary groups of eight goats each. The dietary treatments included a control diet (Basal diet without additive), basal diet +1.5% (w/w) Andrographis paniculata leaf powder (APL) and basal diet +1.5% (w/w) Andrographis paniculata whole plant powder (APW). The trial lasted 100 d following 14 d of adjustment.
RESULTS: The rumen pH and concentration of propionate were greater (P

Matched MeSH terms: Hydrogen-Ion Concentration
Fulltext A response surface approach on hydrolysis condition of eel (Monopterus Sp.) protein hydrolysate with antioxidant activity

Halim, N. R. A., Sarbon, N. M.

International Food Research Journal, 2017;24(3):1081-1093.
MyJurnal

The study aims to determine the optimized condition of eel protein hydrolysate (EPH)
produced using alcalase. The proximate compositions of eel flesh were determined as well.
Enzymatic hydrolysis conditions were optimized using response surface methodology (RSM)
by applying four factors, 3-levels Central Composite Design (CCD) with six centre points. The
model equation was proposed with regards to the time (60min, 120min, 180min), temperature
(40°C, 50°C, 60°C), pH (7, 8, 9) and enzyme concentration (1%, 2%, 3%). The optimum of
hydrolysis condition that be suggested to obtain the optimum yield, degree of hydrolysis (DH)
and antioxidant activity were 84.02 min, 50.18°C, pH 7.89 and 2.26% [enzyme]. The predicted
response values using quadratic model were 10.03% for yield, 83.23% for DH and 89.24%
for antioxidant activity. The chemical composition determination showed that the protein
content increased by more than 5-fold (16.88% to 98.53%) while the fat content was decreased
by 96.48% after hydrolysis. Hydrolysis process had significantly increased the amount of
both hydrophilic (serine and threonine) and hydrophobic amino acids (valine, isoleucine,
phenylalanine, methionine) which contributed to the antioxidant activity of hydrolyzed eel
protein. The enzymatic hydrolysis of eel protein had improved the protein content of EPH with
potential as new natural antioxidant.

Matched MeSH terms: Hydrogen-Ion Concentration
Effect of Various Polyols on the Acid-Denatured States of Champedak Galactose-Binding Lectin

Kameel NIA, Shuib AS, Tayyab S

Protein Pept Lett, 2018;25(3):314-324.
PMID: 29384048 DOI: 10.2174/0929866525666180130155007

BACKGROUND: Champedak galactose-binding (CGB) lectin is a tetrameric protein with noncovalently bound monomers, isolated from Artocarpus integer fruit seeds. We had previously reported existence of a structured monomer and an unfolded monomer of CGB lectin at pH 2.5 and pH 1.5, respectively. Polyols are known to induce significant refolding in denatured proteins and stabilize proteins against environmental stresses. Studies on the effect of various polyols on the acid-denatured states of CGB lectin are lacking.
OBJECTIVE: The objective of this study was to investigate the effects of four different polyols, namely, ethylene glycol, erythritol, xylitol and sorbitol on the acid-denatured states of CGB lectin.
METHODS: CGB lectin was subjected to acid denaturation at pH 2.5 and pH 1.5, both in the absence and presence of 30% (w/v) polyols, i.e. ethylene glycol, erythritol, xylitol and sorbitol. Thermal denaturation of the acid-denatured states was also studied in the absence and presence of these polyols. Different spectroscopic probes such as tryptophan fluorescence, ANS fluorescence and far-UV CD spectral signal were used to monitor structural changes in the acid-denatured states of CGB lectin in the presence of polyols.
RESULTS: Presence of erythritol, xylitol and sorbitol in the incubation mixture was found to stabilize the lectin at both pH 2.5 and pH 1.5, as evident from the burial of the hydrophobic clusters and decreased polarity around Trp residues. These polyols also stabilized the acid-denatured states of CGB lectin against thermal denaturation by shifting the thermal transition curves towards higher temperatures. Exposure of the acid-denatured states of CGB lectin, obtained at pH 2.5 and pH 1.5 to 61°C and 51°C, respectively, induced formation of non-native β-structures, compared to that present at 25°C, and this phenomenon was significantly suppressed in the presence of these polyols. Based on the spectral data, both sorbitol and erythritol appeared to exude better stabilizing effect. On the other hand, ethylene glycol was shown to destabilize the aciddenatured states of CGB lectin.
CONCLUSION: Thermal stabilization of the lectin was noticed in the presence of erythritol, xylitol and sorbitol at both pH 2.5 and pH 1.5. These polyols also stabilize the secondary and tertiary structures of the acid-denatured CGB lectin at 25°C. Ethylene glycol was proved to be a destabilizer of the acid-denatured CGB lectin.

Matched MeSH terms: Hydrogen-Ion Concentration
Novel magnetic graphene oxide functionalized cyanopropyl nanocomposite as an adsorbent for the removal of Pb(II) ions from aqueous media: equilibrium and kinetic studies

Gabris MA, Jume BH, Rezaali M, Shahabuddin S, Nodeh HR, Saidur R

Environ Sci Pollut Res Int, 2018 Sep;25(27):27122-27132.
PMID: 30022389 DOI: 10.1007/s11356-018-2749-9

This work presents the synthesis of the novel silica-cyanopropyl functionalized magnetic graphene oxide (MGO/SiO2-CN) hybrid nanomaterial derived by sol-gel method as a cheap efficient magnetic sorbent for the removal of extremely hazardous lead ions from aqueous media. The integration of the magnetic property, the carbon substrate, and the nitrile (-C ≡ N) containing organic grafted silica matrix promoted the adsorption capability against lead ions along with its simple synthesis recovery and low cost. The prepared nanocomposite was comprehensively characterized by Fourier transform infrared spectroscopy, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. Adsorption of lead was found to be pH dependent because of the charged nature of both analyte and adsorbent surface. Adsorption experiments were conducted under the optimum conditions, and the obtained experimental data from atomic absorption spectroscopy were analyzed using the popular isothermal models namely Langmuir, Freundlich, and Dubinin-Radushkevich isotherms as well as kinetically studied and evaluated for adsorption standard free energy (E). The experimental results have demonstrated the enhanced adsorption capability of the proposed sorbent nanocomposite for lead ion removal with the maximum adsorption capacity of 111.11 mg/g at pH 5.0. The proposed mechanism of lead adsorption was mainly attributed to the complexation of lead positive ions with the grafted -C ≡ N bond. The synergistic effect of the combination of three components (i.e., the magnetic graphene oxide matrix, the triple bond containing organic moiety, and the inorganic porous silica framework) excelled the adsorption capability and proved to be a good candidate as adsorbent for the removal of lead ions.

Matched MeSH terms: Hydrogen-Ion Concentration
Self-assembled three-dimensional reduced graphene oxide-based hydrogel for highly efficient and facile removal of pharmaceutical compounds from aqueous solution

Umbreen N, Sohni S, Ahmad I, Khattak NU, Gul K

J Colloid Interface Sci, 2018 Oct 01;527:356-367.
PMID: 29843021 DOI: 10.1016/j.jcis.2018.05.010

Herein, self-assembled three-dimensional reduced graphene oxide (RGO)-based hydrogels were synthesized and characterized in detail. A thorough investigation on the uptake of three widely used pharmaceutical drugs, viz. Naproxen (NPX), Ibuprofen (IBP) and Diclofenac (DFC) was carried out from aqueous solutions. To ensure the sustainability of developed hydrogel assembly, practically important parameters such as desorption, recyclability and applicability to real samples were also evaluated. Using the developed 3D hydrogels as adsorptive platforms, excellent decontamination for the above mentioned persistent pharmaceutical drugs was achieved in acidic pH with a removal efficiency in the range of 70-80%. These hydrogels showed fast adsorption kinetics and experimental findings were fitted to different kinetic models, such as pseudo-first order, pseudo-second order, intra-particle and the Elovich models in an attempt to better understand the adsorption kinetics. Furthermore, equilibrium adsorption data was fitted to the Langmuir and Freundlich models, where relatively higher R2 values obtained in case of former one suggested that monolayer adsorption played an important part in drug uptake. Thermodynamic aspects were also studied and negative ΔG0 values obtained indicated the spontaneous nature of adsorption process. The study was also extended to check practical utility of as-prepared hydrogels by spiking real aqueous samples with drug solution, where high % recoveries obtained for NPX, IBP and DFC were of particular importance with regard to prospective application in wastewater treatment systems. We advocate RGO-based hydrogels as environmentally benign, readily recoverable/recyclable material with excellent adsorption capacity for application in wastewater purification.

Matched MeSH terms: Hydrogen-Ion Concentration
Fulltext Subcritical Water-Carbon Dioxide Pretreatment of Oil Palm Mesocarp Fiber for Xylooligosaccharide and Glucose Production

Ahmad N, Zakaria MR, Mohd Yusoff MZ, Fujimoto S, Inoue H, Ariffin H, et al.

Molecules, 2018 May 30;23(6).
PMID: 29848973 DOI: 10.3390/molecules23061310

The present work aimed to investigate the pretreatment of oil palm mesocarp fiber (OPMF) in subcritical H₂O-CO₂ at a temperature range from 150⁻200 °C and 20⁻180 min with CO₂ pressure from 3⁻5 MPa. The pretreated solids and liquids from this process were separated by filtration and characterized. Xylooligosaccharides (XOs), sugar monomers, acids, furans and phenols in the pretreated liquids were analyzed by using HPLC. XOs with a degree of polymerization X2⁻X4 comprising xylobiose, xylotriose, xylotetraose were analyzed by using HPAEC-PAD. Enzymatic hydrolysis was performed on cellulose-rich pretreated solids to observe xylose and glucose production. An optimal condition for XOs production was achieved at 180 °C, 60 min, 3 MPa and the highest XOs obtained was 81.60 mg/g which corresponded to 36.59% of XOs yield from total xylan of OPMF. The highest xylose and glucose yields obtained from pretreated solids were 29.96% and 84.65%, respectively at cellulase loading of 10 FPU/g-substrate.

Matched MeSH terms: Hydrogen-Ion Concentration
Methylene blue removal by using pectin-based hydrogels extracted from dragon fruit peel waste using gamma and microwave radiation polymerization techniques

Abdullah MF, Azfaralariff A, Lazim AM

J Biomater Sci Polym Ed, 2018 10;29(14):1745-1763.
PMID: 29989528 DOI: 10.1080/09205063.2018.1489023

This research aims to compare the ability of smart hydrogel in removing the methylene blue prepared by using two different radiation methods. The extracted pectin from the dragon fruit peel (Hylocereus polyrhizus) was used with acrylic acid (AA) to produce a polymerized hydrogel through gamma and microwave radiation. The optimum hydrogel swelling capacity was obtained by varying the dose of radiation, pectin to AA ratio and pH used. From the array of samples, the ideal hydrogel was obtained at pH 8 with a ratio of 2:3 (pectin: AA) using 10 kGy and 400 W radiated gamma and microwave respectively. The performance of both hydrogels namely as Pc/AA(G) (gamma) and Pc/AA(Mw) (microwave) were investigated using methylene blue (MB) adsorption studies. In this study, three variables were manipulated, pH and MB concentration and hydrogel mass in order to find the optimum condition for the adsorption. Results showed that 20 mg of Pc/AA(G) performed the highest MB removal which was about 45% of 20 mg/L MB at pH 8. While 30 mg of Pc/AA(Mw) able to remove up to 35% of 20 mg/L MB at the same pH condition. To describe the adsorption mechanism, both kinetic models pseudo-first-order, pseudo-second-order were employed. The results from kinetic data showed that it fitted the pseudo-first-order as compared to pseudo-second-order model equation. This study provides alternative of green, facile and affective biomaterial for dye absorbents that readily available.

Matched MeSH terms: Hydrogen-Ion Concentration
Equilibrium, kinetic and mechanism studies of Cu(II) and Cd(II) ions adsorption by modified chitosan beads

Sutirman ZA, Sanagi MM, Abd Karim KJ, Wan Ibrahim WA, Jume BH

Int J Biol Macromol, 2018 Sep;116:255-263.
PMID: 29746971 DOI: 10.1016/j.ijbiomac.2018.05.031

In this study, the Cu(II) and Cd(II) ions removal behavior of crosslinked chitosan beads grafted poly(methacrylamide) (abbreviated as crosslinked chitosan-g-PMAm) from single metal ion solutions was investigated. The modified chitosan beads presented a remarkable improvement in acid resistance. The batch experiments demonstrated that pH of solution played a significant role in adsorption. It was found that the adsorption of Cu(II) and Cd(II) were optimum at pH 4 and pH 5, respectively. The maximum adsorption capacities for Cu(II) and Cd(II) based on Langmuir equation were 140.9 mg g-1 and 178.6 mg g-1, respectively. Pseudo-second order gave a better fit for adsorption data with respect to linearity coefficients than pseudo-first order suggesting that chemisorption or electron transfer is the dominant mechanism of the metal ions onto crosslinked chitosan-g-PMAm. In addition, X-ray photoelectron spectroscopy (XPS) investigations revealed that adsorption of both metal ions took place on the surfaces of crosslinked chitosan-g-PMAm by chelation through CNH2, CO and CO groups. Overall, the modified chitosan has proved a promising adsorbent for removal of metal ions.

Matched MeSH terms: Hydrogen-Ion Concentration
Zinc and Metallothionein in the Development and Progression of Dental Caries

Rahman MT, Hossain A, Pin CH, Yahya NA

Biol Trace Elem Res, 2019 Jan;187(1):51-58.
PMID: 29744817 DOI: 10.1007/s12011-018-1369-z

Chronic oxidative stress and reactive oxygen species (ROS) in oral cavity as well as acidic pH on dental enamel surface due to the metabolic activities of bacterial plaque are the major contributors in the development and progression of dental caries. Along with other factors, deposition or dissolution Ca and Mg mostly determines the re- or demineralization of dental enamel. Zn plays an important role for both Ca and Mg bioavailability in oral cavity. Metallothionein (MT), a group of small molecular weight, cysteine-rich proteins (~ 7 kDa), is commonly induced by ROS, bacterial infection, and Zn. In the current review, we evaluated MT at the junction between the progression of dental caries and its etiologies that are common in MT biosynthesis.

Matched MeSH terms: Hydrogen-Ion Concentration
Occurrence, distribution, and sources of emerging organic contaminants in tropical coastal sediments of anthropogenically impacted Klang River estuary, Malaysia

Omar TFT, Aris AZ, Yusoff FM, Mustafa S

Mar Pollut Bull, 2018 Jun;131(Pt A):284-293.
PMID: 29886949 DOI: 10.1016/j.marpolbul.2018.04.019

This baseline assessment reports on the occurrence, distribution, and sources of emerging organic contaminants (EOCs) in tropical coastal sediments of anthropogenically impacted Klang River estuary, Malaysia. Bisphenol A was the highest concentration detected at 16.84 ng g-1 dry weight, followed by diclofenac (13.88 ng g-1 dry weight) and E1 (12.47 ng g-1 dry weight). Five compounds, namely, amoxicillin, progesterone, diazinon, bisphenol A, and E1, were found in all sampling stations assessed, and other compounds such as primidone, diclofenac, testosterone, E2, and EE2 were ubiquitously present in sediment samples, with percentage of detection range from 89.04% to 98.38%. Organic carbon content and pH were the important factors controlling the fate of targeted compounds in the tropical estuarine sediment. On the basis of the literature from other studies, the sources of EOCs are thought to be from wastewater treatment plants, domestic/medical waste discharge, livestock activities, industrial waste discharge, and agricultural activities.

Matched MeSH terms: Hydrogen-Ion Concentration
Hydrodynamic cavitation assisted degradation of persistent endocrine-disrupting organochlorine pesticide Dicofol: Optimization of operating parameters and investigations on the mechanism of intensification

Panda D, Manickam S

Ultrason Sonochem, 2019 Mar;51:526-532.
PMID: 30224289 DOI: 10.1016/j.ultsonch.2018.04.003

Dicofol, a recommended Stockholm convention persistent organic pollutants (POPs) candidate is well known for its endocrine disruptive properties and has been extensively used as an organochlorine pesticide worldwide. The hydrodynamic cavitation (HC) treatment of Dicofol in aqueous media induced by a liquid whistle hydrodynamic cavitaion reactor (LWHCR) has been investigated while considering important parameters such as inlet pressure, initial concentration of Dicofol, solution temperature, pH, addition of H2O2 and radical scavenger for the extent of degradation. The pseudo-first-order degradation rate constant (k) was determined to be 0.073 min-1 with a cavitational yield of 1.26 × 10-5 mg/J at optimum operating conditions and a complete removal of Dicofol was achieved within 1 h of treatment. Considering the removal rate and energy efficiency, the optimal inlet pressure was found to be 7 bar, resulting in a cavitation number of 0.17. High performance liquid chromatography (HPLC) and Gas chromatography mass spectroscopy (GC-MS) analyses indicated a sharp decline in the concentration of Dicofol with treatment time and indicated the presence of degraded products. An 85% total organic carbon (TOC) removal was achieved within 1 h of treatment time, demonstrating successful mineralization of Dicofol. The obtained results suggest that the degradation of Dicofol followed thermal decomposition and successive recombination reactions at bubble-vapor interface. Overall, the attempted hydrodynamic cavitation demonstrated successful and rapid removal of endocrine disruptive chemicals such as Dicofol and is expected to provide efficient solution for wastewater treatment.

Matched MeSH terms: Hydrogen-Ion Concentration
Fulltext Stability Evaluations of Different Types of Vegetable Oil-based Emulsions

Teh SS, Mah SH

J Oleo Sci, 2018;67(11):1381-1387.
PMID: 30404958 DOI: 10.5650/jos.ess18067

The study was aimed at evaluating the effects of vegetable oils on emulsion stability. Palm olein (POo), olive oil (OO), safflower oil (SAF), grape seed oil (GSO), soybean oil (SBO) and sunflower oil (SFO) with different degree of saturation levels were chosen as major ingredient of oil phases. All the emulsions were stored at 4℃, 27℃ and 40℃ for 35 days and subjected to all the stability tests, including temperature variation, centrifuge test, cycle test, pH and slip melting point. The results indicated that POo exhibited the highest stability, followed by SAF, OO, GSO, SFO and SBO. In addition, the results implied that the degree of saturation levels of vegetable oils does give significant effect on emulsion stability based on the centrifuge testing for an approximate 30% usage level of oil. The POo-based emulsion exhibited good emulsion stability throughout the experimental period indicated that POo could be a good carrier oil for various applications in cosmetic industry.

Matched MeSH terms: Hydrogen-Ion Concentration
From formulation of acrylamide-based hydrogels to their optimization for drug release using response surface methodology

Sabbagh F, Muhamad II, Nazari Z, Mobini P, Taraghdari SB

Mater Sci Eng C Mater Biol Appl, 2018 Nov 01;92:20-25.
PMID: 30184743 DOI: 10.1016/j.msec.2018.06.022

This study conducted on the structure of modified acrylamide-based hydrogel by synthesizing the nano composites. The hydrogels employed in this study were provided through a combination of acrylamide monomers, sodium carboxymethyl cellulose (NaCMC) and magnesium oxide (MgO) nanoparticles by crosslinking polymerization. N,N,N',N'-tetramethylethylenediamine and ammonium persulfate as the initiator was applied in the structure of the polymer. Findings of the study considered the nano composites consisting of MgO have the highest swelling ratio compared to pure Aam hydrogels. Thus, MgO is an appropriate nanoparticle to be used in the nano composites. Response surface methodology (RSM) based on a central composite design (CCD Design) was applied to optimize the preparation variables of a hydrogel consisted of MgO, NaCMC. With the swelling ratio for acrylamide-based hydrogel as the response, the effects of two variables, i.e. MgO and NaCMC were investigated. The effects of pH, temperature, MgO, and NaCMC on the drug release were investigated using the CCD design. The predicted appropriate drug release conditions for the hydrogel at the highest rate of temperature (37.50 °C) and pH: 4.10, is at its highest value, while the lower drug release is at temperature 38 °C and pH 3.50. With the desired value of MgO (0.01 g) and amount of NaCMC (0.1 g).

Matched MeSH terms: Hydrogen-Ion Concentration
Characterization of Roselle calyx from different geographical origins

Juhari NH, Bredie WLP, Toldam-Andersen TB, Petersen MA

Food Res Int, 2018 10;112:378-389.
PMID: 30131149 DOI: 10.1016/j.foodres.2018.06.049

Roselle (Hibiscus sabdariffa L.) is considered an underexploited food crop with nutritional and large scale processing potential. Roselle can be utilized as a functional food, mainly due to being rich in vitamin C, anthocyanins, other phytochemicals, and natural color. Although Roselle has been widely planted and consumed, little is known about the composition of aroma profiles. In this study, seventeen samples of dried Roselle calyx were collected from eight countries and the aroma profiles were determined by dynamic headspace sampling and GC-MS and GC-olfactometry. Furthermore, total soluble solids, pH, and color L* a* b* were determined, and sugars and acids were measured using ion chromatography. There were significant (p 

Matched MeSH terms: Hydrogen-Ion Concentration
Biochemical Characterization of Thermostable and Detergent-Tolerant β-Agarase, PdAgaC, from Persicobacter sp. CCB-QB2

Hafizah NF, Teh AH, Furusawa G

Appl Biochem Biotechnol, 2019 Mar;187(3):770-781.
PMID: 30073451 DOI: 10.1007/s12010-018-2849-5

Persicobacter sp. CCB-QB2 belonging to the family Flammeovirga is an agarolytic bacterium and exhibits a diauxic growth in the presence of tryptone and agarose. A glycoside hydrolase (GH) 16 β-agarase, PdAgaC, was identified in the genome of the bacterium and was highly expressed during the second growth phase, indicating the agarase may play an important role in the diauxic growth. In this study, the catalytic domain of PdAgaC (PdAgaCgh) was cloned and characterized. PdAgaCgh showed thermostability at 50 °C and tolerance towards several detergents. In addition, the activity of PdAgaCgh after incubation with 0.1% of SDS and Triton X-100 increased approximately 1.2-fold. On the other hand, PdAgaCgh was sensitive to Fe2+, Ni2+, and Cu2+. The Km and Vmax of PdAgaCgh were 5.15 mg/ml and 2.9 × 103 U/mg, respectively. Interestingly, although the major hydrolytic product was neoagarobiose (NA2), monomeric sugar was also detected by thin-layer chromatographic analysis.

Matched MeSH terms: Hydrogen-Ion Concentration
Fulltext Stability of Bacteriocin-Like Inhibitory Substance (BLIS) Produced by Pediococcus acidilactici kp10 at Different Extreme Conditions

Md Sidek NL, Halim M, Tan JS, Abbasiliasi S, Mustafa S, Ariff AB

Biomed Res Int, 2018;2018:5973484.
PMID: 30363649 DOI: 10.1155/2018/5973484

Nowadays, bacteriocin industry has substantially grown replacing the role of chemical preservatives in enhancing shelf-life and safety of food. The progress in bacteriocin study has been supported by the emerging of consumer demand on the applications of natural food preservatives. Since food is a complex ecosystem, the characteristics of bacteriocin determine the effectiveness of their incorporation into the food products. Among four commercial media (M17 broth, MRS broth, tryptic soy broth, and nutrient broth) tested, the highest growth of Pediococcus acidilactici kp10 and bacteriocin-like-inhibitory substance (BLIS) production were obtained in the cultivation with M17. BLIS production was found to be a growth associated process where the production was increased concomitantly with the growth of producing strain, P. acidilactici kp10. The antimicrobial property of BLIS against three indicator microorganisms (Listeria monocytogenes, Escherichia coli, and Staphylococcus aureus) remained stable upon heating at 100°C but not detectable at 121°C. The BLIS activity was also observed to be stable and active at a wide pH range (pH 2 to pH 7). The BLIS activity remained constant at -20°C and -80°C for 1 month of storage. However, the activity dropped after 3 and 6 months of storage at 4°C, -20°C, and -80°C with more than 80% reduction. The ability of bacteriocin from P. acidilactici kp10 to inhibit food-borne pathogens while remaining stable and active at extreme pH and temperature is of potential interest for future applications in food preservatives.

Matched MeSH terms: Hydrogen-Ion Concentration
Fulltext Production and Characterization of a Bioflocculant Produced by Bacillussalmalaya 139SI-7 and Its Applications in Wastewater Treatment

Abu Tawila ZM, Ismail S, Dadrasnia A, Usman MM

Molecules, 2018 Oct 18;23(10).
PMID: 30340415 DOI: 10.3390/molecules23102689

The production, optimization, and characterization of the bioflocculant QZ-7 synthesized by a novel Bacillus salmalaya strain 139SI isolated from a private farm soil in Selangor, Malaysia, are reported. The flocculating activity of bioflocculant QZ-7 present in the selected strain was found to be 83.3%. The optimal culture for flocculant production was achieved after cultivation at 35.5 °C for 72 h at pH 7 ± 0.2, with an inoculum size of 5% (v/v) and sucrose and yeast extract as carbon and nitrogen sources. The maximum flocculating activity was found to be 92.6%. Chemical analysis revealed that the pure bioflocculant consisted of 79.08% carbohydrates and 15.4% proteins. The average molecular weight of the bioflocculant was calculated to be 5.13 × 10⁵ Da. Infrared spectrometric analysis showed the presence of carboxyl (COO-), hydroxyl (-OH), and amino (-NH₂) groups, polysaccharides and proteins. The bioflocculant QZ-7 exhibited a wide pH stability range from 4 to 7, with a flocculation activity of 85% at pH 7 ± 0.2. In addition, QZ-7 was thermally stable and retained more than 80% of its flocculating activity after being heated at 80 °C for 30 min. SEM analysis revealed that QZ-7 exhibited a clear crystalline brick-shaped structure. After treating wastewater, the bioflocculant QZ-7 showed significant flocculation performance with a COD removal efficiency of 93%, whereas a BOD removal efficiency of 92.4% was observed in the B. salmalaya strain 139SI. These values indicate the promising applications of the bioflocculant QZ-7 in wastewater treatment.

Matched MeSH terms: Hydrogen-Ion Concentration

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links