HyperDSC™(fast scan rate) was used to study the melting behavior of canola (CLO), sunflower (SFO), palm olein (PO), rice bran oils (RBO), and cocoa butter (CB), and was compared to the melting behaviors using conventional DSC. There was an increase in sensitivity with increase in scan rate. Slow scan rate (5 to 20C/min) gave low sensitivity, which increased when the scan rates were increased to 50, 100 and 200C/min. Peak resolution was affected by scan rate depending on the sample weight. Increase in the size of sample coupled with the use of fast scan rate decreased the peak resolution. Generally small sample sizes gave better peak resolution. Results of the effect of scan rate on glass transition (Tg) shows that Tg, which is a weak transition especially in crystalline and low amorphous materials was not detected using conventional scan rates (5 to 20oC/min). It was however detected using of hyperDSC™ scan rates (100 to 200oC/min). Increasing the scan rate resulted in an increase in the peak temperature and the elimination of shoulder peaks, which were caused due to the polymorphic behavior of the triacylglycerols in the oils. The increase in peak temperature caused a shift in the peak position towards a higher temperature value. There is a positive correlation between the peak temperature and scan rate. The correlation coefficients (r) for CLO, SFO, PO, RBO and CB were 0.96, 0.95, 0.97, 0.96 and 0.96 respectively.
This study reports the influence of ZrO2/β-TCP hybridization on the thermal, mechanical, and physical properties of polyamide 12 composites to be suited for bone replacement. Amount of 15 wt% of nano-ZrO2 along with 5,10,15,20 and 25 wt% of micro-β-TCP was compounded with polyamide 12 via a twin-screw extruder. The hybrid ZrO2/β-TCP filled polyamide 12 exhibited higher thermal, mechanical and physical properties in comparison to unfilled polyamide 12 at certain filler loading; which is attributed to the homogenous dispersion of ZrO2/β-TCP fillers particle in polyamide 12 matrix. The hybrid ZrO2/β-TCP filled PA 12 demonstrated an increment of tensile strength by up to 1%, tensile modulus of 38%, flexural strength of 15%, flexural modulus of 45%, and surface roughness value of 93%, as compared to unfilled PA 12. With enhanced thermal, mechanical and physical properties, the newly developed hybrid ZrO2/β-TCP filled PA 12 could be potentially utilized for bone replacement.
The ambient sonocatalytic degradation of congo red, methyl orange, and methylene blue by titanium dioxide (TiO(2)) catalyst at initial concentrations between 10 and 50mg/L, catalyst loadings between 1.0 and 3.0mg/L and hydrogen peroxide (H(2)O(2)) concentrations up to 600 mg/L is reported. A 20 kHz ultrasonic processor at 50 W was used to accelerate the reaction. The catalysts were exposed to heat treatments between 400 and 1000 degrees C for up to 4h to induce phase change. Sonocatalysts with small amount of rutile phase showed better sonocatalytic activity but excessive rutile phase should be avoided. TiO(2) heated to 800 degrees C for 2h showed the highest sonocatalytic activity and the degradation of dyes was influenced by their chemical structures, chemical phases and characteristics of the catalysts. Congo red exhibited the highest degradation rate, attributed to multiple labile azo bonds to cause highest reactivity with the free radicals generated. An initial concentration of 10mg/L, 1.5 g/L of catalyst loading and 450 ppm of H(2)O(2) gave the best congo red removal efficiency of above 80% in 180 min. Rate coefficients for the sonocatalytic process was successfully established and the reused catalyst showed an activity drop by merely 10%.
Presently, plant oils which contain high percentage of linoleic acid 1 are perceived to be a viable alternative to mineral oil for biolubricant applications due to their biodegradability and technical properties. In order to get biodegradable lubricant, triester derivatives compounds (1-5) were synthesized and characterized. The processes involved were monoepoxidation of linoleic acid 2, oxirane ring opening 3, esterification 4 and acylation 5. The structures of the products were confirmed by FTIR, 1H and 13C-NMR and LC-MS. The results that showed lowest temperature properties were obtained for triester 5, with a pour point value (PP) of -73°C, highest onset temperature (260°C) and lowest volatility at 0.30%. Viscosity index (VI) increased for the ester's synthetic compounds (2, 3, 4, 5), while the PP decreased. This behavior is the result of the increase of the chain length of the branching agents. Triester based linoleic acid has improved properties such as low-temperature and tribological properties. These results will make it feasible for plant oil to be used for biolubricants, fuels in chain saws, transmission oil and brake fluid.
Zinc oxide (ZnO) photocatalysts were successfully synthesized via chemical and green, environmentally-benign methods. The work highlights the valorization of banana peel (BP) waste extract as the reducing and capping agents to produce pure, low temperature, highly crystalline, and effective ZnO nanoparticles with superior photocatalytic activities for the removal of hazardous Basic Blue 9 (BB9), crystal violet (CV), and cresol red (CR) dyes in comparison to chemically synthesized ZnO. Their formation and morphologies were verified by various optical spectroscopic and electron microscopic techniques. XRD results revealed that the biosynthesized ZnO exhibited 15.3 nm crystallite size when determined by Scherrer equation, which was smaller than the chemically synthesized ZnO. The FTIR spectra confirmed the presence of biomolecules in the green-mediated catalyst. EDX and XPS analyses verified the purity and chemical composition of ZnO. Nitrogen sorption analysis affirmed the high surface area of bio-inspired ZnO. Maximum removal efficiencies were achieved with 30 mg green ZnO catalyst, 2.0 × 10-5 M BB9 solution, alkaline pH 12, and irradiation time 90 min. Green-mediated ZnO showed superior photodegradation efficiency and reusability than chemically synthesized ZnO. Therefore, this economical, environment-friendly photocatalyst is applicable for the removal of organic contaminants in wastewater treatment under visible light irradiation.
The effect of temperature change on the working and setting time of a glass ionomer luting cement and a resin luting cement was measured using the oscillating rheometer. The time taken for each cement to set was calculated from the chart recordings. It was observed that as the temperature increased, the working and setting time of both materials decreased. However, the reduction was much more marked for the dual curing resin cement.
This paper presents the results of a study on the effect of temperature on geopolymers manufactured using pozzolanic materials (fly ash). In this paper, we report on our investigation of the performance of porous geopolymers made with fly ash after exposure to temperatures from 600 °C up to 1000 °C. The research methodology consisted of pozzolanic materials (fly ash) synthesized with a mixture of sodium hydroxide and sodium silicate solution as an alkaline activator. Foaming agent solution was added to geopolymer paste. The geopolymer paste samples were cured at 60 °C for one day and the geopolymers samples were sintered from 600 °C to 1000 °C to evaluate strength loss due to thermal damage. We also studied their phase formation and microstructure. The heated geopolymers samples were tested by compressive strength after three days. The results showed that the porous geopolymers exhibited strength increases after temperature exposure.
A modeling procedure that predicts trihalomethane (THM) formation from field sampling at the treatment plant and along its distribution system using Tampin district, Negeri Sembilan and Sabak Bernam district, Selangor as sources of data were studied and developed. Using Pearson method of correlation, the organic matter measured as TOC showed a positive correlation with formation of THM (r=0.380,P=0.0001 for Tampin and r=0.478,P=0.0001 for Sabak Bernam). Similar positive correlation was also obtained for pH in both districts with Tampin (r=0.362,P=0.0010) and Sabak Bernam (r=0.215,P=0.0010). Chlorine dosage was also found to have low correlation with formation of THM for the two districts with Tampin (r=0.233,P=0.0230) and Sabak Bernam (r=0.505,P=0.0001). Distance from treatment plant was found to have correlation with formation of THM for Tampin district with r=0.353 and P=0.0010. Other parameters such as turbidity, ammonia, temperature and residue chlorine were found to have no correlation with formation of THM. Linear and non-linear models were developed for these two districts. The results obtained were validated using three different sets of field data obtained from own source and district of Seremban (Pantai and Sg. Terip), Negeri Sembilan. Validation results indicated that there was significant difference in the predictive and determined values of THM when two sets of data from districts of Seremban were used with an exception of field data of Sg. Terip for non-linear model developed for district of Tampin. It was found that a non-linear model is slightly better than linear model in terms of percentage prediction errors. The models developed were site specific and the predictive capabilities in the distribution systems vary with different environmental conditions.
The steady-state flow test was conducted on pink-fleshed guava, pink-fleshed pomelo and soursop juice concentrates using a rheometer to understand its rheological behaviour. The power law model was used and a master-curve was created using the shear rate-temperature-concentration superposition technique to predict rheological properties from a wide range of temperatures and concentrations. All three juice concentrates undergo a double horizontal shift whilst the pink-fleshed guava required an additional vertical shift. The final equations show shear-thinning behaviour of pink-fleshed guava, pink-fleshed pomelo and soursop with flow behaviour index of 0.2217, 0.7507 and 0.6347, respectively. The final master-curve predicts shear stress at wide range of shear rates, i.e. between 10-2 and 106 s-1 for the pink-fleshed guava, 100 and 106 s-1 for the pink-fleshed pomelo and 100 and 107 s-1 for the soursop. The results provide useful information and effective technique to predict fruit juice concentrates behaviour affected by heat changes during processing.
The aim of the measurement of this data is to evaluate the Indoor Air Quality (IAQ) in terms of chemical and physical parameters. Data were collected at three different kindergartens having different surrounding activities (industrial, institutional, residential area). The chemical parameters measured were respirable suspended particulates of PM10, PM2.5, PM1, carbon monoxide and carbon dioxide, and the concentrations are within the acceptable limit. Physical parameters of wind speed are within the standard, while temperature and relative humidity exceeded the acceptable limit. A strong correlation was found between the chemical IAQ parameters with thermal comfort parameters (temperature and relative humidity). The concentration of IAQ pollutants is higher in order of residential > institutional > industrial.
An electrochemical cell using an organic compound, copper (II) phthalocyanine-tetrasulfonic acid tetrasodium salt (CuTsPc,) has been fabricated and investigated as a solution-based temperature sensor. The capacitance and resistance of the ITO/CuTsPc solution/ITO chemical cell has been characterized as a function of temperature in the temperature range of 25-80 °C. A linear response with minimal hysteresis is observed. The fabricated temperature sensor has shown high consistency and sensitive response towards a specific range of temperature values.
While a group of oral commensals have been implicated in the aetiology of chronic periodontitis; the asaccharolytic Gram negative anaerobe Porphyromonas gingivalis is most commonly reported to be associated with severe forms of the disease. Although a variety of human tissues can produce a number of peptidylarginine deiminase (PAD), enzymes that convert peptide bound arginine residues to citrulline, P. gingivalis is one of the few prokaryotes known to express PAD. Protein and peptide citrullination are important in the development of rheumatoid arthritis and in recent years a number of authors have suggested a possible link between periodontitis and rheumatoid arthritis (RA). Indeed, some have linked P. gingivalis directly to RA via the action of PAD. Accordingly, the prime purpose of this study was to further characterise PAD in P. gingivalis cells particular emphasis on substrate specificity, using arginine containing peptides and RA relevant proteins.
Considering its excellent thermal stability, alkyl phosphonium surfactant: triisobutyl(methyl)phosphonium
(TIBMP) was used in this research as an intercalant for surface
modification of Na+-MMT via ion exchange process forming organomontmorillonite
(OMMT). The OMMT was then used as filler in poly(methyl methacrylate) (PMMA) via
melt intercalation technique. OMMT decomposed at a higher temperature than commercial
alkyammonium modified MMT. Exfoliated and intercalated types of nanocomposites
are obtained from PMMA/OMMTs at low and high content of OMMT loading, depending
on the space of those clay platelets had to disperse in PMMA. The ability of OMMT to
carry a certain load applied in PMMA matrix enhances the tensile strength in all composites.
TIBMP are compatible with PMMA matrix, and significantly improves the tensile
properties of PMMA composites.
A suitable and cost-effective microfabrication technique for processing aluminum micropart is required, as the choice
of aluminum microparts for aerospace, electronics and automobile components is preferred over other metals due to its
excellent properties. Meanwhile, powder injection molding (PIM) is identified as an economical manufacturing technique
for processing ceramic and micro-metal powders into microparts and or components. Therefore, this study investigates
formulation and processing of aluminum PIM feedstock using a custom-made machine. The investigation is focused on
the effect of mixing process parameters (powder loading, rotor speed and mixing temperature) and the suitability of
the backbone polymer. The formulated PIM feedstock constituents are paraffin wax (PW), stearic acid (SA), high-density
polyethylene (HDPE)/ medium-density polyethylene (MDPE) alternatively and aluminum micro-metal powder. Taguchi
method is used for the design of experiments (DOEs) and analysis. In addition, response surface methodology (RSM) is
employed to develop empirical viscosity models. The optimum powder-binder mixing ratio of 58:42 vol. % with rotor
speed of 43 rpm were determined for preparing aluminum PIM feedstock using mini-lab mixer developed. The empirical
model developed for aluminum PIM feedstock viscosity shows a good fit with R2
values of 0.84 using HDPE and 0.96 for
MDPE binder system. This investigation demonstrates preparation and suitability of aluminum PIM feedstock using waxbased
binder system.
This study describes the development of a rapid and sensitive Loop-mediated isothermal
amplification assay for detection of swine DNA in adulterated meat and meat products. The
need to protect consumer’s right to eat foods of their choices, has made it imperative for
researchers to develop efficient means of screening and certification of food products. Six sets
of LAMP primers designed based on porcine tRNA lysine gene and ATPase subunit 8 genes
were used for the assay. Amplification was carried out under constant temperature (630C), using
a simple laboratory water bath. Average time spent in amplification and detection of results was
25 min. All results were visually detected and confirmed by electrophoresis. Detection limit of
the assay was 0.03 femtogram (fg) much high than the PCR assay, and detection probability of
the assay was 100%. Detection of 0.5% of pork spiked with 99.5% of cattle beef is indicative
of the sensitivity and robustness of the assay. This could serve as a prototype for development
of a sensitive and inexpensive Swine DNA LAMP detection kit.
Herein, an efficient epoxidation of 1-nonene is described. In a simple epoxidation system, commercially available Novozym 435, an immobilized Candida antarctica lipase B, and hydrogen peroxide (H(2)O(2)) were utilized to facilitate the in situ oxidation of phenylacetic acid to the corresponding peroxy acid which then reacted with 1-nonene to give 1-nonene oxide with high yield and selectivity. The aliphatic terminal alkene was epoxidised efficiently in chloroform to give an excellent yield (97%-99%) under the optimum reaction conditions, including temperature (35 °C), initial H(2)O(2) concentration (30%), H(2)O(2) amount (4.4 mmol), H(2)O(2) addition rate (one step), acid amount (8.8 mmol), and stirring speed (250 rpm). Interestingly, the enzyme was stable under the single-step addition of H(2)O(2) with a catalytic activity of 190.0 Ug-1. The entire epoxidation process was carried out within 12 h using a conventional water bath shaker.
This work explores the thermoluminescence (TL) and photoluminescence (PL) properties of Ag/Y co-doped zinc oxide (ZnO) nanophosphor. The proposed dosimeter was prepared by the coprecipitation method and sintered at temperatures from 400°C to 1000°C in an air atmosphere. Raman spectroscopy was studied to investigate the structural features of this composition. The new proposed dosimeter revealed two peaks at 150°C and 175°C with a small shoulder at high temperature (225°C). The PL spectrum showed strong green emissions between 500 to 550 nm. The Raman spectrum showed many bands related to the interaction between ZnO, silver (Ag), and yttrium oxide (Y2 O3 ). The rising sintering temperature enhanced the TL glow curve intensity. The Ag/Y co-doped ZnO nanophosphor showed an excellent linearity index within a dose from 1 to 4 Gy. The minimum detectable dose (MDD) of the Ag/Y co-doped ZnO nanopowder (pellets) equaled 0.518 mGy. The main TL properties were achieved in this work as follows: thermal fading (37% after 45 days at 1 and 4 Gy), optical fading (53% after 1 h and 68% after 6 h by exposure to sunlight), effective atomic number (27.6), and energy response (flat behavior from 0.1 to 1.3 MeV). Finally, the proposed material shows promising results nominated to be used for radiation measurements.
Molecular Dynamics (MD) simulations have been used to understand how protein structure, dynamics, and flexibility are affected by adaptation to high temperature for several years. We report here the results of the high temperature MD simulations of Bacillus stearothermophilus L1 (L1 lipase). We found that the N-terminal moiety of the enzyme showed a high flexibility and dynamics during high temperature simulations which preceded and followed by clear structural changes in two specific regions; the small domain and the main catalytic domain or core domain of the enzyme. These two domains interact with each other through a Zn(2+)-binding coordination with Asp-61 and Asp-238 from the core domain and His-81 and His-87 from the small domain. Interestingly, the His-81 and His-87 were among the highly fluctuated and mobile residues at high temperatures. The results appear to suggest that tight interactions of Zn(2+)-binding coordination with specified residues became weak at high temperature which suggests the contribution of this region to the thermostability of the enzyme.
Lipases are known for their versatility in addition to their ability to digest fat. They can be used for the formulation of detergents, as food ingredients and as biocatalysts in many industrial processes. Because conventional enzymes are frangible at high temperatures, the replacement of conventional chemical routes with biochemical processes that utilize thermostable lipases is vital in the industrial setting. Recent theoretical studies on enzymes have provided numerous fundamental insights into the structures, folding mechanisms and stabilities of these proteins. The studies corroborate the experimental results and provide additional information regarding the structures that were determined experimentally. In this paper, we review the computational studies that have described how temperature affects the structure and dynamics of thermoenzymes, including the thermoalkalophilic L1 lipase derived from Bacillus stearothermophilus. We will also discuss the potential of using pressure for the analysis of the stability of thermoenzymes because high pressure is also important for the processing and preservation of foods.
This paper deals with the performance and emission analysis of a multicylinder diesel engine using biodiesel along with an in-depth analysis of the engine heat losses in different subsystems followed by the energy balance of all the energy flows from the engine. Energy balance analysis allows the designer to appraise the internal energy variations of a thermodynamic system as a function of ''energy flows" across the control volume as work or heat and also the enthalpies associated with the energy flows which are passing through these boundaries. Palm and coconut are the two most potential biodiesel feed stocks in this part of the world. The investigation was conducted in a four-cylinder diesel engine fuelled with 10% and 20% blends of palm and coconut biodiesels and compared with B5 at full load condition and in the speed range of 1000 to 4000 RPM. Among the all tested blends, palm blends seemed more promising in terms of engine performance, emission, and heat losses. The influence of heat losses on engine performance and emission has been discussed thoroughly in this paper.