Synthetic materials that are capable of healing upon damage are being developed at a rapid pace because of their
many potential applications. Here, new healing chemically cross-linked hydrogel of poly(2-hydroxyethyl methacrylate)
(pHEMA) was prepared. The healing hydrogel was achieved by heating above its glass transition (Tg
). The intermolecular
diffusion of dangling chain and the chain slippage led to healing of the gel. The peaks in attenuated total reflectance
(ATR) confirmed that hydrogel was formed while rheological studies had determined the minimum for healing temperature
is 48.5o
C. The results showed that ratio stress of the healable hydrogel can reach until 92 and 91% of first and second
healing cycle, respectively. The morphology of the sample was carried out to evaluate the self-property of hydrogel.
In this study, various methods and applications of flat plate solar collectors are discussed and pictorial representations are presented. Low temperature applications of flat plate collectors are identified in solar cooking, solar water heating, space and air heating, industrial heating plants and in agricultural produce drying processes. Basic equations, as presented by many researchers in the performances of flat plate collectors, are also presented. The review discusses the analysis of losses from flat plate collectors towards obtaining the overall heat loss coefficient which indicate the performance of flat plate collectors.
The melting curves of 11 vegetable oils have been characterised. Vegetable oil samples that were cooled at a constant rate (5 degrees C/min) from the melt showed between one and seven melting endotherms upon heating at four different heating rates (1, 5, 10 and 20 degrees C/min) in a differential scanning calorimeter (DSC). Triacylglycerol (TAG) profiles and iodine value analyses were used to complement the DSC data. Generally, the melting transition temperature shifted to higher values with increased rates of heating. The breadth of the melting endotherm and the area under the melting peak also increased with increasing heating rate. Although the number of endothermic peaks was dependent on heating rate, the melting curves of the oil samples were not straightforward in that there was no correlation between the number of endothermic peaks and heating rates. Multiple melting behaviour in DSC experiments with different heating rates could be explained by: (1) the melting of TAG populations with different melting points; and (2) TAG crystal reorganisation effects. On the basis of the corollary results obtained, vegetable oils and fats may be distinguished from their offset-temperature (Toff) values in the DSC melting curves. The results showed that Toff values of all oil samples were significantly (p < 0.01) different in the melting curves scanned at four different scanning rates. These calorimetric results indicate that DSC is a valuable technique for studying vegetable oils.
Microwave heating was determined in this study to be suitable for the detachment and drying of palm fruits from whole bunches, cut bunches and spikelets. Microwave treatment of the palm fruits was able to attain the objectives of conventional fresh palm fruits sterilization processeses such as fruit softening, nut conditioning and halting of enzymatic lipolysis. Palm oil and kernel oil solvent extracted respectively from the microwave treated whole fruits and kernel were found to have a good quality of low free fatty acid content. This technology, together with the solvent extraction of the dehydrated fruits, may have the potential to be a continuous, dry and clean technology for palm oil milling.
This research was conducted to study the effect of reinforcement particles on iron-cobalt (FeCo) composites. The composition of silicon carbide (SiC) was varied from 0 to 20 wt%. The composite was fabricated via powder metallurgy (PM) method, which consists of mixing, compaction and sintering processes. The powder was mixed for 2 hours to obtain uniformity between SiC and Fe-Co matrix and compacted to a cylindrical shape at 250 MPa. Samples were sintered for 2 hours at 900 o C with 10 o C/minute heating rate in argon atmosphere. The influences of reinforcement particle on the sintered samples were characterized in terms of microstructure and hardness testing. The Fe-Co/20wt%SiC composites show highest hardness value.
The global trend in increasing plant-based protein diets due to health and ideological reasons, has created an increased demand for food legumes that exceeds current production. To meet this demand, it is timely to reduce relying solely on soybean, and explore the potential of the underutilised legumes that are cultivated regionally. Underutilised legumes are rich in protein, carbohydrates and other nutrients that are essential for consumer. However, relatively little is known about their anti-nutritional properties and processing methods. Anti-nutritional factors (ANFs) such as enzyme inhibitors are prevalent in legumes and may interfere with digestibility and nutrient absorption. Nevertheless, an optimised food processing method will overcome this challenge and warrant a safe inclusion of legume in plant-based protein diets. Hence current study aimed to optimise the food processing methods (soaking, wet heating, autoclaving and freezing) and evaluate their efficiency in eliminating the enzyme inhibitors [trypsin, chymotrypsin (CIA) and α-amylase (AIA) inhibitors] present in seven underutilised legumes. Current study showed that autoclaving at 121 °C for 15 min reduced the AIA in all underutilised legumes tested. The AIA and CIA of bambara groundnut were successfully inactivated by wet heating at 50 °C for 60 min, and by autoclaving at 121 °C for 15 min. While the CIA of chickpea was successfully inactivated by freezing at - 80 °C for 24 h.
owder injection molding (PIM) is able to produce porous titanium alloy/hydroxyapatite composite through the space holder technique. Thermal debinding and sintering processes were the main challenges due to different properties of metal and ceramic in producing such composite. This study focused on the effect of different space holders on the physical and mechanical properties of debound and sintered porous titanium aloi/hydroxyapatite composite. The feedstock is containing of 80 wt. % of titanium alloy/hydroxyapatite with 20 wt. % of space holders such as sodium chloride (NaCl) and polymethylmethacrylate (PMMA), respectively. The binders were then removed from the injected samples by two stages of debinding; solvent and thermal debinding. The sintering was performed at three different temperatures 1100oC, 1200oC and 1300oC at a heating rate of 10oC /min and holding time of 5 h. It was found that the samples containing PMMA space holder was fractured after sintering. While, the samples containing NaCl space holder successfully formed pores and not fractured. At sintering temperature of 1300oC, the density, compressive strength and porosity volume percentages for the sintered sample containing NaCl space holder were 3.05 g/cm3, 91.7 MPa. and 11.9 vol%, respectively.
Five luminescent polymorphic aggregates of trinuclear Cu(i)-pyrazolate, namely [anti-Cu3L3]2 (1), [syn-Cu3L3·C2H5OH]2 (2), [anti-Cu3L3·C2H5OH]n (3), [anti-Cu3L3·0.5C7H8]n (4) and [syn-Cu3L3·C8H10]n (5) (HL = 4-(pyridin-4-ylthio)-3,5-dimethyl-1H-pyrazole), were reported. The trimeric Cu3L3 fragments present syn- and anti-conformations dependent on the dangled direction of 4-pyridyl groups on the two sides of the Cu3Pz3 plane (Pz = pyrazolate). Intertrimeric NPyCu weak coordination bonds associate these Cu3L3 fragments together to form dimeric or polymeric structures, which are further stabilized by crystallized solvent molecules or intertrimeric CuCu interactions. The solvated complexes (3-5) may be transformed into the unsolvated complex 1 by evacuation of the crystallized solvents upon heating. All these complexes emit from green to yellow under UV irradiation, which originated from the triplet excited states of metal to ligand charge transfer (3MLCT) mixed with intertrimeric CuCu interactions. This work provides a novel kind of supramolecular aggregate based on Cu3Pz3 beyond the classical π-acidbase adducts and metallophilicity-dependent dimers/oligomers.
A high bituminous shale horizon from the Gurha mine in the Bikaner sub-basin of the Rajasthan District, NW India, was studied using a collection of geochemical and petrological techniques. This study investigated the nature and environmental conditions of the organic matter and its relation to the unconventional oil-shale resources of the bituminous shale. The analyzed shales have high total organic carbon and total sulfur contents, suggesting that these shale sediments were deposited in a paralic environment under reducing conditions. The dominant presence of organic matter derived from phytoplankton algae suggests warm climatic marine environment, with little connection to freshwater enhancing the growth of algae and other microorganisms. The analyzed bituminous shales have high aquatic-derived alginite organic matters, with low Pr/Ph, Pr/n-C17, and Ph/n-C18 ratios. It is classified as Type II oil-prone kerogen, consistent with high hydrogen index value. Considering the maturity indicators of geochemical Tmax (
Several binary and ternary medium- and long-chain triacylglycerol (MLCT)-enriched margarine formulations were examined for their solid fat content, heating profile, polymorphism and textural properties. MLCT feedstock was produced through enzymatic esterification of capric and stearic acids with glycerol. The binary formulations were produced by mixing MLCT feedstock blend (40%–90%) and palm olein (10%–60%) with 10% increments (w/w). Solid fat profiles of commercial margarines were used as a reference to determine the suitability of the formulations for margarine production. The solid fat content of the binary formulations of MO 82 and MO 91 (M, MLCT, O, palm olein) were similar to the commercial margarines at 25°C which met the basic requirement for efficient dough consistency. Ternary formulations using reduced MLCT feedstock blend proportion (from 80%–90% to 60%–70%) were also developed. The reduction of MLCT feedstock blend was
done as it had the highest production cost (3USD/kg) in comparison to palm olein (0.77USD/kg) and palm stearin (0.7USD/kg). The proportions of 5%–15% of palm stearin were substituted with palm olein in MO 64 and MO 73 (M, MLCT; O, palm olein) formulations with 5% increment (w/w). As a result, MOS 702010 and MOS 603010 (M, MLCT; O, palm olein; S, palm stearin) margarine formulations showed similar SFC % to the commercial margarines at 25ºC. These formulations were subsequently chosen to produce margarines. The onset melting and complete melting points of MLCT-enriched margarine formulations were high (51.04ºC –57.93ºC) due to the presence of a high amount of long chain saturated fatty acids. Most of the formulations showed β΄- crystals. MOS 702010 was selected as the best formulation due to values for textural parameters comparable (P
Recently, as a supplement of cement, the utilization of pozzolanic materials in cement and concrete manufacturing has increased significantly. This study investigates the scope to use pozzolanic wastes (slag, palm oil fuel ash and rice husk ash) as an alkali activated binder (AAB) that can be used as an alternative to cement. To activate these materials, sodium hydroxide solution was used at 1.0, 2.5 and 5.0 molar concentration added into the mortar, separately. The required solution was used to maintain the flow of mortar at 110% ± 5%. The consistency and setting time of the AAB-paste were determined. Mortar was tested for its flow, compressive strength, porosity, water absorption and thermal resistance (heating at 700 °C) and investigated by scanning electron microscopy. The experimental results reveal that AAB-mortar exhibits less flow than that of ordinary Portland cement (OPC). Surprisingly, AAB-mortars (with 2.5 molar solution) achieved a compressive strength of 34.3 MPa at 28 days, while OPC shows that of 43.9 MPa under the same conditions. Although water absorption and porosity of the AAB-mortar are slightly high, it shows excellent thermal resistance compared to OPC. Therefore, based on the test results, it can be concluded that in the presence of a chemical activator, the aforementioned pozzolans can be used as an alternative material for cement.
The implementation of this research consists of 2 (two) aspects: the making and testing of bio-briquettes called technological aspects and economic analysis called economic aspects. Bio-briquettes is made from cashew nutshell waste obtained from Southeast Sulawesi, Indonesia. It is followed by pyrolysis, which is carried out in a simple batch type reactor by heating using liquefied petroleum gas (LPG). The bio-briquettes product has a calorific value of 29.49 MJ/kg, moisture content of 5.3%, ash content of 4.96%, volatile substances content of 17.16%, and carbon content of 72.62%, which meets the universally accepted bio-briquettes standard (SNI 016235-2000), Japanese, English and ISO 17225. The bio-briquettes product is suitable as an energy source. The economic analysis of the cashew nutshell was analyzed to determine its economic feasibility. For the bio-briquettes production capacity in 2,000 tons/year, cashew nut shell-briquettes products can be sold at 1,052,878 USD/year. The total production cost is USD842,304/year. The net profit is of USD147,402/year. The cost of LPG for 2,000 tons/year production capacity is USD954,358/years. The replacement of LPG with cashew seed bio-briquettes tends to help the average household of Muna Regency community to reduce the annual cost by 37.00%. In conclusion, bio-briquettes production's economic feasibility as analyzed from the investment rate is 23.55%, payout time is 3.42 years, and break-even point is 50.09%.
Most of the automotive companies use cast iron for their engine blocks. Restoration of obliterated number on these iron surfaces by chemical etching is known to be quite difficult. Heating of the obliterated surface using oxyacetylene flame is an alternative recovery treatment suggested in literature and used in practice. However chemical etching has been established to be the most sensitive technique for detection of metal deformation present under stamped serial numbers. Hence, the current work investigated the suitability of some common etchants on cast iron surfaces with a view to determining the most suitable one for revealing the obliterated marks. The reagents tested were mostly copper containing Fry's reagent and its modifications. Two cast iron engine blocks (3.29%C and 3.1%C) of two cars--a Proton Saga and a Toyota--were utilized for the experiments. The engine blocks were cut into several small plates and each plate was stamped with some numerical characters at 8 kN load using Instron Table Mounted Universal Testing Machine. The depth of stamping impression varied between 0.2 mm and 0.3 mm. The stamped number was completely ground off manually using a metal file. The grounded surface was then polished smooth using emery papers and etched with a few selected reagents mostly by swabbing. Experimental results showed that a modified Fry's composition consisting of 4 5g CuCl(2), 100 mL HCl, and 180 mL H(2)O restored the number with better contrast at a reasonably shorter time. The above reagent is a slightly modified form of one of the Fry's original compositions--45 g CuCl(2), 180 mL HCl, and 100 mL H(2)O. Quite importantly the proposed reagent restored the original stamped numbers of both Proton and Toyota cars and also a Mitsubishi car that had been obliterated. The most widely used Fry's composition (90 g CuCl(2), 120 mL HCl and 100 mL H(2)O), although recovered the obliterated number, did not cause the desired contrast.
This research investigated the removal of lead (Pb(2+)) by a novel biochar derived from palm oil sludge (POS-char) by slow pyrolysis. Multistage optimizations with central composite design were carried out to firstly optimize pyrolysis parameters to produce the best POS-char for Pb(2+) removal and secondly to optimize adsorption conditions for the highest removal of Pb(2+). The optimum pyrolysis parameters were nitrogen flowrateof30mLmin(-1), heating rateof10°Cmin(-1), temperatureof500°C and timeof30min. The optimum Pb(2+) adsorption conditions were concentrationof200mgL(-1), timeof60min, dosageof0.3g and pH of 3.02. The various functional groups within POS-char played a vital role in Pb(2+) uptake. Regeneration was demonstrated to be feasible using hydrochloric acid. Adsorption equilibrium was best described by Freundlich model. At low concentration range, adsorption kinetic obeyed pseudo-first-order model, but at high concentration range, it followed pseudo-second-order model. Overall, the results highlighted that POS-char is an effective adsorbent for Pb(2+) removal.
Differential scanning calorimetry (DSC) is developed and used for detection of butter adulteration with lard. Butter has the similar characteristics to lard makes lard a desirable adulterant in butter. DSC provides unique thermal profiling for lard and butter. In the heating thermogram of the mixture, there was one major endothermic peak (peak A) with a smaller shoulder peak embedded in the major peak that gradually smoothed out to the major peak as the lard percent increased. In the cooling thermogram, there were one minor peak (peak B) and two major exothermic peaks, peak C which increased as lard percent increased and peak D which decreased in size as the lard percent increased. From Stepwise Multiple Linear Regression (SMLR) analysis, two independent variables were found to be able to predict lard percent adulteration in butter with R2 (adjusted) of 95.82. The SMLR equation of lard percent adulteration in butter is 293.1 - 11.36 (Te A) - 2.17 (Tr D); where Te A is the endset of peak A and Tr D is the range of thermal transition for peak D. These parameters can serve as a good measurement parameter in detecting lard adulteration in butter. DSC is a very useful means for halal screening technique to enhance the authenticity of Halal process.
Electron cyclotron resonance heating method of Particle-in-Cell code was used to analyze heating phenomena, axial kinetic energy, and self-consistent electric field of confined electron plasma in ELTRAP device by hydrogen and helium background gases. The electromagnetic simulations were performed at a constant power of 3.8 V for different RF drives (0.5 GHz- 8 GHz), as well as for 1 GHz constant frequency at these varying amplitudes (1 V-3.8 V). The impacts of axial and radial temperatures were found maximum at 1.8 V and 5 GHz as compared to other amplitudes and frequencies for both background gases. These effects are higher at varying radio frequencies due to more ionization and secondary electrons production and maximum recorded radial temperature for hydrogen background gas was 170.41 eV. The axial kinetic energy impacts were found more effective in the outer radial part (between 0.03 and 0.04 meters) of the ELTRAP device due to applied VRF through C8 electrode. The self-consistent electric field was found higher for helium background gas at 5 GHz RF than other amplitudes and radio frequencies. The excitation and ionization rates were found to be higher along the radial direction (r-axis) than the axial direction (z-axis) in helium background gas as compared to hydrogen background gas. The current studies are advantageous for nuclear physics applications, beam physics, microelectronics, coherent radiation devices and also in magnetrons.
A 1.7 m2 flat plate solar air heater was designed and developed in the Department of Agricultural Mechanization, The University of Agriculture Peshawar, Pakistan in collaboration with the Department of Environmental Sciences, University of Peshawar, Pakistan. It was operated under an average solar irradiance of 0.9 kJ.m-2.h-1 in the month of September, 2013. It worked under an efficiency of 7.5 to 21%. The heat collected by the air heater was given to air flowing as a medium inside it. This hot air was given to a drying section and water heating tank for drying and water heating purposes. The drying section provided a temperature in the range of 40-50oC and humidity of 10-30% from 10:00 am to 3:00 pm. The water heating tank provides hot water with a temperature of 35- 45oC from 10:00 am to 5:00 pm. Furthermore, the drying section was used to dry apples, onions and persimmons. All the products showed a consistent moisture loss from them with an optimum drying rate. The two term exponential model showed that all the three products dried have a good correlation with drying time with R2 values higher than 0.90. It was concluded that flat plate solar air heaters is the best technology for water heating and drying purposes and is a good alternative of conventional energy sources.
In this paper, the heat transfer effect on the unsteady boundary layer flow of a Casson fluid past an infinite oscillating vertical plate with Newtonian heating is investigated. The governing equations are transformed to a systems of linear partial differential equations using appropriate non-dimensional variables. The resulting equations are solved analytically by using the Laplace transform method and the expressions for velocity and temperature are obtained. They satisfy all imposed initial and boundary conditions and reduce to some well-known solutions for Newtonian fluids. Numerical results for velocity, temperature, skin friction and Nusselt number are shown in various graphs and discussed for embedded flow parameters. It is found that velocity decreases as Casson parameters increases and thermal boundary layer thickness increases with increasing Newtonian heating parameter.
This paper studied the thermal behaviour of pineapple leaf fibre (PALF) reinforced high impact polystyrene (HIPS) composite. Thermogravimetric analysis (TGA) and differential scanning calorimetric (DSC) analysis were used to measure the thermal characteristic of HIPS/PALF composites. In particular, the TGA analysis was utilized to measure the degradation and decomposition of materials in neat polystyrene, pineapple fibre, and the composites. The measurements were carried out in the temperature of 25°C – 800°C, at a heating rate of 20°C min-1 and the nitrogen gas flow was 50 mL min-1. The temperature of the DSC analysis was programmed to be between 25°C – 300°C. The results from TGA analysis show that the addition of pineapple fibre has improved the thermal stability of the composites as compared to neat HIPS. In addition, the effects of compatibilising agent and surface modification of PALF with alkali treated were also determined and compared.
Dielectric properties study is important in understanding the interaction between materials within electromagnetic field. By knowing and understanding the dielectric properties of materials, an efficient and effective microwave heating process and products can be designed. In this study, the dielectric properties of several encapsulation wall materials were measured using open-ended coaxial probe method. This method was selected due to its simplicity and high accuracy. All materials exhibited similar behavior. The result inferred that β-cyclodextrin (BC), starch (S), Arabic (GA) and maltodextrin (M) with various dextrose equivalent exhibited effective encapsulation wall materials in microwave encapsulation-drying technique owing to loss tangent values which were higher than 0.1 at general application frequency of 2.45 GHz. Thus, these were found to be suitable as wall material to encapsulate the selected core material in this microwave encapsulation-drying method. On contrary, sodium caseinate showed an ineffective wall material to be used in microwave encapsulation-drying. The differences in the values of dielectric constant, loss factor and loss tangent were found to be contributed by frequency, composition and bulk density.