This paper attempts to integrate both a forward and reverse supply chain to design a closed-loop supply chain network (CLSC). The problem in the design of a CLSC network is uncertainty in demand, return products and the quality of return products. Scenario analyses are generated to overcome this uncertainty. In contrast to the existing supply chain network design models, a new application of a CLSC network was studied in this paper to reduce waste. A multi-product, multi-tier mixed integer linear model is developed for a CLSC network design. The main objective is to maximize profit and provide waste management decision support in order to minimize pollution. The result shows applicability of the model in the tire industry. The model determines the number and the locations of facilities and the material flows between these facilities.
Liquid natural rubber (LNR) was functionalized into liquid epoxidized natural rubber (LENR) and hydroxylated LNR (LNROH)
via oxidation using a Na2
WO4
/CH3
COOH/H2
O2
catalytic system. Microstructures of LNR and functionalized LNRs
were characterized using Fourier Transform Infrared (FTIR) and Nuclear Magnetic Resonance (NMR) spectroscopies. The
effect of CH3
COOH, H2
O2
, Na2
WO4
, reaction time and temperature. reaction time and temperature on epoxy content were
investigated. LNR-OH was obtained when oxidation reaction was conducted at a longer reaction time, higher temperature
or excess amount of catalyst. Thermogravimetric analysis (TGA) reported the thermal behavior of functionalized LNRs.
Molecular weight and polydispersity index (PDI) were determined using gel permeation chromatography (GPC).
Ammonium-enriched skim latex serum - used for absorption of contaminating ammonia gas - when composted with other rubber tree wastes, is promising as a good compost. The objective of this research was to utilize ammonium-enriched skim latex serum (S) as a raw composting ingredient after being combined with para sawdust (W1) and para rubber leaves (W2). Several ratios of S, W1 and W2 were experimented in a 15L composting vessel to determine the most effective compost. The best ratio was found to be 3:1:3 by weight at 12-day retention. The modified 30 L composting reactor employed with the derived optimum mixing conditions yielded N, P and K of 2.40, 1.51 and 14.84 %w/w. The growth of Brassica alboglabra after application of this compost combined with a chemical fertilizer generated the highest fresh weight (4.48 g/plant). Thus, compost from these wastes could be used as a fertilizer and logically should contribute to cost saving of waste disposal.
Introduction: This study aimed to (i) determine rapid weight loss (RWL) practices among Malaysian elite combat sports athletes and (ii) examine the relationship between the characteristics of athletes, self-reported history of weight loss, perceived influence on weight loss and RWL practices.
Methods: This was a cross-sectional study conducted at the Malaysian National Sports Institute among elite combat sports athletes (n=40) recruited via a convenience sampling method. The athletes completed a self-administered validated Rapid Weight Loss Questionnaire. Each response was provided a score and the total RWL score corresponded to the aggressiveness of weight management methods. Partial correlations were used to assess the relationships between total RWL score and independent variables.
Results: The prevalence of RWL among the athletes was high (92.5%). Training with rubber or plastic suits (62.2%) and meal-skipping (27.0%) were the most common RWL techniques practised by the respondents. Aggressive weight-cutting as depicted by a higher total RWL score that correlated with most weight ever lost, duration taken to lose weight, influence of training colleagues and coaches, BMI, current weight and post-competition weight regain (all p
The importance of the performance of concrete cannot be neglected since it is the early indicator of its physical and mechanical properties. It became more important when material with different physical properties than normal material such as rubber tire was used as concrete constituent. This paper presented apart of research result conducted on mortar and concrete with crumb rubber. Crumb rubber was replaced at 10%, 15% and 20% as sand replacement by volume. In addition, ordinary Portland cement was added to silica fume at 10% and 15% by weight. The properties measured in this study are air content and workability test. As for workability, superplasticizers were constantly used at 1% dosage for all mortar mixture, and 0.5% to 0.7% for concrete mixture. The air content was set at 4% to 6% and mortar flow test was conducted on a steel plate, shocked 15 times in 15 seconds and concrete slump test was carried out using slump cone equipment. Pressure method was used to measure air content. All mixes were done in a controlled room temperature. Results showed that when CR was added in the mixture segregation was observed in mortar requiring a high dose of superplasticizer to be added to improve the workability while air-modifying agent was used to reduce the mortar air content. In concrete mixture, low dosage of superplasticizers was required for workability and air-entrained agent was injected into the mixture to increase the air content between 4%-6%.
Congenital talipes equinovarus (CTEV) or clubfoot is a complex deformity of the foot that is characterised by four main deformities; forefoot cavus and adductus, hindfoot varus and ankle equinus. Currently, the Ponseti method is the most general and recognized treatment with a high success rate of over 90%. The treatment involves gentle manipulation and serial casting. However, the casting method could create complications for the patients such as soft-tissue damage and inconvenience in following the treatment schedule especially for those living far away from hospital. The aim of this research is to develop an adjustable corrective device for clubfoot treatment based on the techniques in the Ponseti method and at the same time attempt to eliminate the side-effects. The prototype consists of six adjustable movements from six different mechanisms to correct the four deformities. The prototype was developed using 3D printing method and the main material used is polylactic acid (PLA), rubber, aluminium and cotton fabric with sponge. The total weight of the prototype is around 300 g.
This paper details a study conducted to evaluate the performance of cold in-place recycling (CIPR) using polymer modified asphalt emulsion (PMAE). The asphalt emulsion was modified using natural rubber latex (NRL). Four proportions of reclaimed asphalt pavement (RAP) which are 0%, 25%, 50% and 75% were mixed with natural aggregates and modified asphalt emulsion using natural rubber latex (NRL). The results showed that the optimum modified asphalt emulsion for each proportion of RAP decreased due to the increase in RAP content. Results obtained from Indirect Tensile Strength (ITS) and Uniaxial Compressive Strength (UCS) test for the mixes complied with the requirements of the Road Engineering Association of Malaysia (REAM) specifications. The unsoaked and soaked ITS values obtained were 0.2 MPa and 0.15 MPa respectively, and the minimum compressive strength of CIPR mix obtained was 0.7 MPa. Based on the evaluation of performance for the four RAP proportions, it was determined that 50% of RAP gave the best combination of the CIPR mixture.
A safety evaluation test on human for latex films made from Radiation Prevulcanized Natural Rubber Latex (RVNRL) with sulfur-containing antioxidant was studied. Sulfur test has confirmed that there was sulfur compound presence in RVNRL derived from antioxidant used in this study. Two types of safety evaluation test were being adopted which are Patch Test and Modified Draize-95 test and this test proved that there is no clinical evidence on the presence of sulfur compound in RVNRL that may induce Type IV allergy in the unsensitized general user population. Both clinical test shows that the highest score value produced by test subjects is 1 and not exceed the allowable limit.
Road distress results in high maintenance costs. However, increased understandings of asphalt behaviour and properties coupled with technological developments have allowed paving technologists to examine the benefits of introducing additives and modifiers. As a result, polymers have become extremely popular as modifiers to improve the performance of the asphalt mix. This study investigates the performance characteristics of epoxidized natural rubber (ENR)-modified hot-mix asphalt. Tests were conducted using ENR-asphalt mixes prepared using the wet process. Mechanical testing on the ENR-asphalt mixes showed that the resilient modulus of the mixes was greatly affected by testing temperature and frequency. On the other hand, although rutting performance decreased at high temperatures because of the increased elasticity of the ENR-asphalt mixes, fatigue performance improved at intermediate temperatures as compared to the base mix. However, durability tests indicated that the ENR-asphalt mixes were slightly susceptible to the presence of moisture. In conclusion, the performance of asphalt pavement can be enhanced by incorporating ENR as a modifier to counter major road distress.
Environmental pollution is one of the major concerns in the 21st century; where billions of tonnes
of harmful chemicals are produced by industries such as petroleum, paints, food, rubber, and
plastic. Phenol and its derivatives infiltrate the ecosystems and have become one of the top major
pollutants worldwide. This review covers the major aspects of immobilization of phenoldegrading
bacteria as a method to improve phenol bioremediation. The use of various forms of
immobilization matrices is discussed along with the advantages and disadvantages of each of the
immobilization matrices especially when environmental usage is warranted. To be used as a
bioremediation tool, the immobilized system must not only be effective, but the matrices must be
non-toxic, non-polluting and if possible non-biodegradable. The mechanical, biological and
chemical stability of the system is paramount for long-term activity as well as price is an
important factor when the very large scale is a concern. The system must also be able to tolerate
high concentration of other toxicants especially heavy metals that form as co-contaminants, and
most immobilized systems are geared towards this last aspect as immobilization provides
protection from other contaminants.
A modular typed dielectric barrier discharge (DBD) device is designed and tested for air and water remediation. The module is made of a number of DBD tubes that can be arranged in series or parallel. Each of the DBD tubes comprises inner electrode enclosed with dielectric barrier and arranged as such to provide a gap for the passage of gases. Non-thermal plasma generated in the gap effectively creates gaseous chemical reactions. Its efficacy in the remediation of gas stream containing high NOx, similar to diesel emission and wastewater containing latex, are presented. A six tubes DBD module has successfully removed more than 80% of nitric oxide from the gas stream. In another arrangement, oxygen was fed into a two tubes DBD to generate ozone for treatment of wastewater. Samples of wastewater were collected from a treatment pond of a rubber vulcanization pilot plant. The water pollution load was evaluated by the chemical oxygen demand (COD) and biological oxygen demand (BOD5) values. Preliminary results showed some improvement (about 13%) on the COD after treatment and at the same time had increased the BOD5 by 42%. This results in higher BOD5/COD ratio after ozonation which indicate better biodegradability of the wastewater.
Large areas of rainforest in Asia have been converted to plantations, with uncertain effects on soil biodiversity. Using standard metagenetic methods, we compared the soil biota of bacteria, fungi, and nematodes at three rainforest sites in Malaysia with two rubber plantation sites with similar soils and geology. We predicted the following: (1) that the rubber sites would have a lower α- and β-diversity than the rainforest sites, due to the monospecific canopy cover and intensive management with herbicides, pesticides, and fertilizers, and (2) that due to differences in the physical and biotic environment associated with cultivation, there would be distinct communities of bacteria, fungi, and nematodes. However, regarding (1), the results showed no consistent difference in α- and β-diversity of bacteria, fungi, or nematodes between rainforest and rubber plantation sites. It appears that conversion of rainforest to rubber plantations does not necessarily result in a decrease in diversity of soil biota. It may be that heterogeneity associated with the cultivation regimen compensates for loss of biotically imposed heterogeneity of the original rainforest. Regarding (2), as predicted there were statistically significant differences in community composition between rainforest and rubber plantation for bacteria, fungi, and nematodes. These differences could be related to a range of factors including light level, litter fall composition, pH, C and N, selecting a distinct set of soil taxa, and it is possible that this in itself would affect long-term soil function.
Hevea brasiliensis Muell. Arg, a member of the family Euphorbiaceae, is the sole natural resource exploited for commercial production of high-quality natural rubber. The properties of natural rubber latex are almost irreplaceable by synthetic counterparts for many industrial applications. A paucity of knowledge on the molecular mechanisms of rubber biosynthesis in high yield traits still persists. Here we report the comprehensive genome-wide analysis of the widely planted H. brasiliensis clone, RRIM 600. The genome was assembled based on ~155-fold combined coverage with Illumina and PacBio sequence data and has a total length of 1.55 Gb with 72.5% comprising repetitive DNA sequences. A total of 84,440 high-confidence protein-coding genes were predicted. Comparative genomic analysis revealed strong synteny between H. brasiliensis and other Euphorbiaceae genomes. Our data suggest that H. brasiliensis's capacity to produce high levels of latex can be attributed to the expansion of rubber biosynthesis-related genes in its genome and the high expression of these genes in latex. Using cap analysis gene expression data, we illustrate the tissue-specific transcription profiles of rubber biosynthesis-related genes, revealing alternative means of transcriptional regulation. Our study adds to the understanding of H. brasiliensis biology and provides valuable genomic resources for future agronomic-related improvement of the rubber tree.
This study was conducted to screen the endophytic bacteria as a biological control agent (BCA) against Ganoderma boninense. A total of 581 endophytic bacteria were successfully isolated from symptomless oil palm root tissues at Teluk Intan, Perak, Malaysia. Three endophytic bacteria, Pseudomonas aeruginosa GanoEB1, Burkholderia cepacia GanoEB2, and Pseudomonas syringae GanoEB3 were found to have a potential as BCA based on their percentage inhibition of radial growth (PIRG) in dual culture and culture filtrate tests. Two nursery trials were conducted to evaluate the capability of these bacteria to suppress Ganoderma disease in oil palm seedlings that were artificially infected with G. boninense using rubber wood block (RWB) sitting technique. The percentage of disease incidence (DI), severity of foliar symptoms (SFS) and dead seedlings were used as the assessment tools. As a result, DI and SFS have developed much slower in the seedlings that were pre-treated with bacteria compared to untreated seedlings. After 6 months of inoculation, Ganoderma disease incidence was reduced from 62-75% in the seedlings treated with P. aeruginosa GanoEB1, followed by B. cepacia GanoEB2 (31-59%) and P. syringae GanoEB3 (30-31%). Among these three endophytic bacteria, P. aeruginosa GanoEB1 was the most effective in controlling Ganoderma disease and the dead seedlings were in the range of 13.3-26.7%, followed by B. cepacia GanoEB2 (33.3% for both trials) and P. syringae GanoEB3 (33.3-40.0%) compared to untreated seedlings at 60% for both trials. A field study needs to be conducted to verify their effectiveness in controlling Ganoderma in oil palm.
Mating compatibility and restriction analyses of Internal Transcribed Spacer (ITS) regions were performed to determine the relations between Ganoderma boninense, the most common species associated with basal stem rot in oil palm and Ganoderma isolates from infected oil palm, two ornamental palms, sealing wax palm (Cyrtostachys renda) and MacArthur palm (Ptychosperma macarthurii), an isolate from coconut stump (Cocos nucifera), Ganoderma miniatocinctum, Ganoderma zonatum and Ganoderma tornatum. The results showed that G. boninense was compatible with Ganoderma isolates from oil palm, G. miniatocinctum and G. zonatum, Ganoderma isolates from sealing wax palm, MacArthur palm and coconut stump. G. boninense was not compatible with G. tornatum. Therefore, the results suggested that the G. boninense, G. miniatocinctum, G. zonatum, and Ganoderma isolates from oil palm, ornamental palms and coconut stump could represent the same biological species. In performing a restriction analysis of the ITS regions, variations were observed in which five haplotypes were generated from the restriction patterns. An unweighted pair-group method with arithmetic averages (UPGMA) cluster analysis showed that all the Ganoderma isolates were grouped into five primary groups, and the similarity values of the isolates ranged from 97% to 100%. Thus, a restriction analysis of the ITS regions showed that G. boninense and the Ganoderma isolates from other palm hosts were closely related. On the basis of the mating compatibility test and the restriction analysis of the ITS regions performed in this study, a diverse group of Ganoderma species from oil palm and other palm hosts are closely related, except for G. tornatum and Ganoderma isolates from tea and rubber.
Streptomyces sp. strain CFMR 7, which naturally degrades rubber, was isolated from a rubber plantation. Whole genome sequencing and assembly resulted in 2 contigs with total genome size of 8.248 Mb. Two latex clearing protein (lcp) genes which are responsible for rubber degrading activities were identified.
Percutaneous pinning after closed reduction is commonly used to treat supracondylar fractures of the humerus in children. Minor pin tract infections frequently occur. The aim of this study was to prevent pin tract infections using a rubber stopper to reduce irritation of the skin against the Kirschner (K) wire following percutaneous pinning. Between July 2011 and June 2012, seventeen children with closed supracondylar fracture of the humerus of Gartland types 2 and 3 were treated with this technique. All patients were treated with closed reduction and percutaneous pinning and followed up prospectively. Only one patient, who was a hyperactive child, developed pin tract infection due to softening of the plaster slab. We found using the rubber stopper to be a simple and inexpensive method to reduce pin tract infections following percutaneous pinning.
The effect of carbon black on the mechanical properties of elastomers is of great interest, because the filler is one of principal ingredients for the manufacturing of rubber products. While fillers can be used to enhance the properties of elastomers, including stress-free swelling resistance in solvent, it is widely known that the introduction of fillers yields significant inelastic responses of elastomers under cyclic mechanical loading, such as stress-softening, hysteresis and permanent set. When a filled elastomer is under mechanical deformation, the filler acts as a strain amplifier in the rubber matrix. Since the matrix local strain has a profound effect on the material's ability to absorb solvent, the study of the effect of carbon black content on the swelling characteristics of elastomeric components exposed to solvent in the presence of mechanical deformation is a prerequisite for durability analysis. The aim of this study is to investigate the effect of carbon black content on the swelling of elastomers in solvent in the presence of static mechanical strains: simple extension and simple torsion. Three different types of elastomers are considered: unfilled, filled with 33 phr (parts per hundred) and 66 phr of carbon black. The peculiar role of carbon black on the swelling characteristics of elastomers in solvent in the presence of mechanical strain is explored.
Objective: To evaluate feasibility of hand gloves as a rubber dam isolation alternative, in respect of physical properties. Materials and Methods: A randomized controlled trial study design was used. Three types of gloves were tested with two types of a rubber dam used as the control group. Cut-out pattern of dumb-bell shapes were made from 35 samples for each type of groups and tensile strength were tested using Universal Testing Machine and the Trapezium X software. All tests for physical requirements were performed in accord-ance with American Society for Testing and Materials D412, Standard Test Methods for Vulcanized Rubber and Thermoplastic Rubbers and Thermoplastic Elastomers-Tension. Findings were analyzed by analysis of vari-ance (ANOVA) and differences were compared using a Tukey-Kramer interval calculated at the 0.05 signifi-cance level. Results: Heavy gauge rubber dam has the highest Mean (calculated at the 0.05 significance level) except for maximum stress calculated at entire area. Medium-gauge rubber dam has significantly higher tensile strength (44.5075 N/mm2) when compared to heavy-gauge rubber dam (35.7787 N/mm2) although it was 0.09mm thinner. Discovery 2020 Powder Free Latex Examination Gloves with tensile strength value of 28.5922 N/mm2 (±3.27366) is more than the minimum requirement specified by American Federal Specification ZZ-R90B Rubber Dam (Dental, 1985) (4000 pounds per square inch or 27.6 N/mm2). For all variable tested, all groups are significantly different from each other. The mean square between the groups was quite large. Conclusion: This study shows that there are significant differences between the physical strength of latex gloves when com-pared to rubber dam. However, the comparison between thickness and tensile strength among various rubber dam, did not correspond proportionately. Only one type of rubber gloves met the minimum requirement but that is just one aspect. In view of these mixed results, more research is needed before we can conclude that it is feasable that we use hand gloves to replace rubber dam.
Incineration and disposal of carbon fiber waste from the aircraft industry lead to serious energy consumption and environmental pollution. The use of this waste as reinforcement is a wise approach to appreciate the high performance of the carbon fiber. This study is part of our effort to develop new green rubber foam from recycled carbon fiber prepreg (rCFP) reinforced natural rubber via internal mixer. It is focusing on the effect of different rCFP loading at 1, 3, 5, and 7 parts per hundred rubbers (phr) as reinforcement. The samples were prepared by melt compounding using an internal mixer and expanded via two step heat transfer foaming process. The physical properties of the green rubber foam were characterized and the results were observed to systematically correlate with the impact properties of the foam. The absorbed energy of the foam increases up to 0.3 joules with increasing relative foam density of 0.81 which is associated with the formation of smaller foam cells ~0.68mm and more spherical shape pores.