Patient undergoes orthodontic treatment with fixed appliances have more plaque
retentive area compare to normal person. Therefore, this patient requires higher standard of oral
hygiene care. One of adjunctive cleaning device for oral hygiene care is water irrigator. There are
several types of water irrigator available in the market such as syringe type, electricity and battery
operated. However, the problem is the available water irrigators are expensive. (Copied from article).
Lemongrass leaves are often under-utilised and unexploited. In this study, lemongrass leaves were used to produce water soluble essential oil using a steam distillation system. Water steam was passed through the lemongrass leaves which were placed and supported on a grid above the water in a distiller. The steam distillation system was fabricated and optimised using Response Surface Methodology (RSM). The maximum oil yield with optimal relative citral content is obtained at 6.69 of plant-to-water ratio, 26.68 minutes of distillation time using air-dried lemongrass leaves left under the shade for two days. At the optimum conditions, the predicted oil yield was 0.6719% of lemongrass (C. citratus) oil which contains 71.79% of citral content.
Prolonged drought conditions have adverse environmental and socio-economic impacts due to unmet water demands. Defining drought is difficult because of its onset and ending time. Therefore, characterisation of drought is essential for drought management operations. Thus, drought indices come in handy and are a practical approach to assimilate large amounts of data into quantitative information which can then be applied for drought forecasting, declaring drought levels, contingency planning and impact assessments. This study analyses drought events using indices, namely SPI and Deciles Index, computed with DrinC software program but are not popular in Malaysia. It is observed that both indices are identical and suitable for drought occurrences.
Strength and durability are important characteristics of concrete and desired engineering properties. Exposure to aggressive environment threatens durability of concrete. Previous studies on bio-concrete using several types of bacteria, including sulphate reduction bacteria (SRB), had to increase durability of concrete have shown promising results. This study used mixtures designed according to concrete requirement for sea water condition with SRB composition of 3%, 5% and 7% respectively. The curing time were 28, 56 and 90 days respectively. The mechanical properties, namely compressive strength and water permeability, were tested using cube samples. The results showed compressive strength had higher increase than the control at 53.9 Mpa. The SRB with 3%composition had maximum water permeability. Thus, adding SRB in concrete specimens improves compressive strength and water permeability. This is particularly suitable for applications using chloride ion penetration (sea water condition) where corrosion tends to affect durability of concrete constructions.
The experimental set-up of this study mimicked recirculating aquaculture systems (RAS) where water quality parameters such as dissolved oxygen, pH, temperature, and turbidity were controlled and wastes produced by fish and feeding were converted to inorganic forms. A key process in the RAS was the conversion of ammonia to nitrite and nitrite to nitrate through nitrification. It was hypothesized that algae inclusion in RAS would improve the ammonia removal from the water; thereby improving RAS water quality and stability. To test this hypothesis, the stability of the microbiota community composition in a freshwater RAS with (RAS+A) or without algae (RAS-A) was challenged by introducing an acute pH drop (from pH 7 to 4 during three hours) to the system. Stigeoclonium nanum, a periphytic freshwater microalga was used in this study. No significant effect of the algae presence was found on the resistance to the acute pH drop on ammonia conversion to nitrite and nitrite conversion to nitrate. Also the resilience of the ammonia conversion to the pH drop disruption was not affected by the addition of algae. This could be due to the low biomass of algae achieved in the RAS. However, with regard to the conversion step of nitrite to nitrate, RAS+A was significantly more resilient than RAS-A. In terms of overall bacterial communities, the composition and predictive function of the bacterial communities was significantly different between RAS+A and RAS-A.
Matched MeSH terms: Fresh Water*; Water Microbiology; Water Quality
Highly photocatalytically active copper chromite nanostructured material were prepared via a novel simple hydrothermal reaction between [Cu(en)2(H2O)2]Cl2 and [Cr(en)3]Cl3.3H2O at low temperature, without adding any pH regulator or external capping agent. The as-synthesized nanostructured copper chromite was analyzed by transmission electron microscopy (TEM), UV-vis diffuse reflectance spectroscopy, energy dispersive X-ray microanalysis (EDX), scanning electron microscopy (SEM), X-ray diffraction (XRD) and Fourier transform infrared (FT-IR) spectroscopy. Results of the morphological investigation of the as-synthesized products illustrate that the shape and size of the copper chromite depended on the surfactant sort, reaction duration and temperature. Moreover, the photocatalytic behavior of as-obtained copper chromite was evaluated by photodegradation of acid blue 92 (anionic dye) as water pollutant.
Matched MeSH terms: Fresh Water/chemistry; Water Pollutants, Chemical/isolation & purification*
This paper discusses the effect of jet impingement of water on a photovoltaic thermal (PVT) collector and compound parabolic concentrators (CPC) on electrical efficiency, thermal efficiency and power production of a PVT system. A prototype of a PVT solar water collector installed with a jet impingement and CPC has been designed, fabricated and experimentally investigated. The efficiency of the system can be improved by using jet impingement of water to decrease the temperature of the solar cells. The electrical efficiency and power output are directly correlated with the mass flow rate. The results show that electrical efficiency was improved by 7% when using CPC and jet impingement cooling in a PVT solar collector at 1:00 p.m. (solar irradiance of 1050 W/m² and an ambient temperature of 33.5 °C). It can also be seen that the power output improved by 36% when using jet impingement cooling with CPC, and 20% without CPC in the photovoltaic (PV) module at 1:30 p.m. The short-circuit current ISC of the PV module experienced an improvement of ~28% when using jet impingement cooling with CPC, and 11.7% without CPC. The output of the PV module was enhanced by 31% when using jet impingement cooling with CPC, and 16% without CPC.
In this article we present the first comparative study of the transient decay dynamics of photo-generated charges for the three polymorphs of TiO2. To our knowledge, this is the first such study of the brookite phase of TiO2 over timescales relevant to the kinetics of water splitting. We find that the behavior of brookite, both in the dynamics of relaxation of photo-generated charges and in energetic distribution, is similar to the anatase phase of TiO2. Moreover, links between the rate of recombination of charge carriers, their energetic distribution and the mode of transport are made in light of our findings and used to account for the differences in water splitting efficiency observed across the three polymorphs.
Confocal Raman microscopy (CRM) was able to quantify the β-carotene concentration in oil droplets and determine the partitioning characteristics of β-carotene within the emulsion system in situ. The results were validated by a conventional method involving solvent extraction of β-carotene separately from the total emulsion as well as the aqueous phase separated by centrifugation, and quantification by absorption spectrophotometry. CRM also enabled the localization of β-carotene in an emulsion. From the Raman image, the β-carotene partitioning between the aqueous and oil phases of palm olein-in-water emulsions stabilized by whey protein isolate (WPI) was observed. Increasing the concentration of β-carotene in an emulsion (from 0.1 to 0.3g/kg emulsion) with a fixed gross composition (10% palm olein:2% WPI) decreased the concentration of β-carotene in the oil droplet. CRM is a powerful tool for in situ analyses of components in heterogeneous systems such as emulsions.
Chemical composition and flocculation efficiency were investigated for a commercially produced tannin - based coagulant and flocculant (Tanfloc). The results of Fourier Transform Infrared Spectroscopy (FTIR) and Energy Dispersive Spectroscopy (EDX) confirmed what claimed about the chemical composition of Tanfloc. For moderate polluted municipal wastewater investigated in both jar test and pilot plant, Tanfloc showed high turbidity removal efficiency of approximately 90%, while removal efficiencies of BOD5 and COD were around 60%. According to floc size distribution, Tanfloc was able to show distinct performance compared to Polyaluminum chloride (PAC). While 90% of flocs produced by Tanfloc were smaller than 144 micron, they were smaller than 96 micron for PAC. Practically, zeta potential measurement showed the cationic nature of Tanfloc and suggested coincidence of charge neutralization and another flocculation mechanism (bridging or patch flocculation). Sludge Volumetric Index (SVI) measurements were in agreement with the numbers found in the literature, and they were less than 160 mL/g. Calcium cation as flocculation aid showed significant improvement of flocculation efficiency compared to other cations. Finally Tanfloc showed competing performance compared to PAC in terms of turbidity, BOD5 and COD removal, floc size and sludge characteristics.
Matched MeSH terms: Water Pollutants, Chemical/chemistry*; Waste Water/chemistry*
Considering the chemical properties of batik effluents, an efficient and economical treatment process was established to treat batik wastewater containing not only high levels of Si and chemical oxygen demand (COD), but also toxic heavy metals. After mixing the effluents obtained from the boiling and soaking steps in the batik process, acidification using concentrated hydrochloric acid (conc. HCl) was conducted to polymerize the silicate under acidic conditions. Consequently, sludge was produced and floated. XRD and FT-IR analyses showed that wax molecules were coordinated by hydrogen bonding with silica (SiO2). The acidification process removed ∼78-95% of COD and ∼45-50% of Si, depending on the pH. In the next stage, magnesium oxide (MgO) was applied to remove heavy metals completely and almost 90% of the Si in the liquid phase. During this step, about 70% of COD was removed in the hydrogel that arose as a consequence of the crosslinking characteristics of the formed nano-composite, such as magnesium silicate or montmorillonite. The hydrogel was composed mainly of waxes with polymeric properties. Then, the remaining Si (∼300 mg/L) in the wastewater combined with the effluents from the rinsing steps was further treated using 50 mg/L MgO. As a final step, palm-shell activated carbon (PSAC) was used to remove the remaining COD to
Matched MeSH terms: Water Pollutants, Chemical/chemistry*; Waste Water*
The production, optimization, and characterization of the bioflocculant QZ-7 synthesized by a novel Bacillus salmalaya strain 139SI isolated from a private farm soil in Selangor, Malaysia, are reported. The flocculating activity of bioflocculant QZ-7 present in the selected strain was found to be 83.3%. The optimal culture for flocculant production was achieved after cultivation at 35.5 °C for 72 h at pH 7 ± 0.2, with an inoculum size of 5% (v/v) and sucrose and yeast extract as carbon and nitrogen sources. The maximum flocculating activity was found to be 92.6%. Chemical analysis revealed that the pure bioflocculant consisted of 79.08% carbohydrates and 15.4% proteins. The average molecular weight of the bioflocculant was calculated to be 5.13 × 10⁵ Da. Infrared spectrometric analysis showed the presence of carboxyl (COO-), hydroxyl (-OH), and amino (-NH₂) groups, polysaccharides and proteins. The bioflocculant QZ-7 exhibited a wide pH stability range from 4 to 7, with a flocculation activity of 85% at pH 7 ± 0.2. In addition, QZ-7 was thermally stable and retained more than 80% of its flocculating activity after being heated at 80 °C for 30 min. SEM analysis revealed that QZ-7 exhibited a clear crystalline brick-shaped structure. After treating wastewater, the bioflocculant QZ-7 showed significant flocculation performance with a COD removal efficiency of 93%, whereas a BOD removal efficiency of 92.4% was observed in the B. salmalaya strain 139SI. These values indicate the promising applications of the bioflocculant QZ-7 in wastewater treatment.
Matched MeSH terms: Water Purification/methods*; Waste Water/chemistry*
Gelatin from goatskin pretreated with hydrochloric acid and extracted with distilled water at 60oC for 9 hours was characterized and compared to that of bovine skin gelatin (BSG). A yield of 10.26% (wet weight basis) was obtained. Goatskin gelatin (GSG) had high protein (86.58%), suitable moisture (9.58%), low fat (1.46%) and low ash (0.11%) content. The functional properties of GSG including gel strength (301 g bloom) and emulsion activity index (94.27%) were higher than the functional properties of BSG including gel strength (192 g bloom) and emulsion activity index (49.74%). The foaming property of GSG (102%) was lower than that of BSG (164.67%). This study shows that GSG has a high potential for application as a source of commercial gelatin.
Owing to their high-risk factor, many attempts have been made to remove radionuclides from water. Sr2+ ions are the target of removal by synthesized hydroxyapatite in this research. A facile method for synthesizing high-surface-area hydroxyapatite by in-situ precipitation using excess diammonium phosphate solution and without any additive was developed. The highest surface area achieved using this method was 177.00 m2/g, and the synthesized hydroxyapatite was also mesoporous. The effects of different pH, temperatures, and ion concentrations during synthesis on the properties of the hydroxyapatite were assessed, and it was found that a low temperature and high pH were optimal for synthesizing high-surface-area hydroxyapatite. The maximum strontium removal capacity of 28.51 mg/g was achieved when the pH-7.5 solution was used. This performance is competitive in comparison with previously developed synthesized materials. Synthesized hydroxyapatite could effectively remove radioactive strontium from an aqueous solution for nuclear waste management.
1. 1. Paris green was used as a larvicide on an inland hilly estate where A. maculatus was the carrier-and where most of the water treated was moving, more or less rapidly. 2. 2. Three different diluents were tried, viz., lime, talcum and soapstone powder. 3. 3. The strength of the mixture was one part of Paris green to ninety-nine parts of diluent by volume. 4. 4. Distribution was carried out by mechanical blowers and sprayers. 5. 5. The application was checked twenty-four hours afterwards. For one month it was checked forty-eight hours afterwards. 6. 6. There was an increase in breeding places-most of which were found in moving water. 7. 7. There was an increase in larvæ, many of them being over two days old. 8. 8. In spite of treatment of epidemics with plasmochin and quinine, the malaria rate was higher than during the previous year. The rise was more or less consistent, pointing to constant infections. 9. 9. The morbidity rate, death rate and infantile mortality were apparently not adversely affected, but in view of the treatments given with plasmochin, they are of no help in deciding the value of Paris green. 10. 10. There was a distinct fall in anti-larval costs, but the total anti-malarial costs were still high on account of the treatments necessary for epidemics of malaria. 11. 11. The advantages and disadvantages of Paris green are discussed.
Anthropogenic pressures are causing substantial degradation to the freshwater ecosystems globally and Malaysia has not escaped such a bleak scenario. Prompted by the predicament, this study's objective was to pioneer a river assessment system that can be readily adopted to monitor, manage and drive improvement in a wholesome manner. Three sets of a priori metrics were selected to form the Ichthyofaunal Quality Index (IQI: biological), Water Quality Index (WQI: chemical) and River Physical Quality Index (RPQI: physical). These indices were further integrated on equal weighting to construct a novel Malaysian River Integrity Index (MyRII). To test its robustness, the MyRII protocol was field tested in four eco-hydrological zones located in the Kampar River water basin for 18 months to reveal its strengths, weaknesses, and establish the "excellent", "good", "average", "poor" and "impaired" thresholds based on the "best performer" reference site in an empirical manner. The resultant MyRII showed a clear trend that corresponded with different levels of river impairment. Test site zone A which was a reference site with minimal disturbance achieved the highest MyRII (88.95 ± 4.29), followed by partially disturbed zone B (61.95 ± 5.90) and heavily disturbed zone C (50.00 ± 4.29). However, the MyRII in zone D (59.9 ± 6.39), which was a heavily disturbed wetland that was disjointed from the river, did not conform to such trend. Also unveiled and recognized, however, are some unexpected nuances, limitations and challenges that emerged from this study. These are critically discussed as precautions when interpreting and implementing the MyRII protocol. This study adds to the mounting body of evidence that water resource stakeholders and policymakers must look at the big picture and adopt the "balanced ecosystem" mind-set when assessing, restoring and managing the rivers as a freshwater resource.
Citation: A case study on institutional development in the water and sanitation sectors and integration of PHC with rural water supply and sanitation in Malaysia. Manila: World Health Organization, Regional Office for the Western Pacific; 1985
Concentration of Ra-226 and Ra-228 activities in water and sediment samples were measured using the Liquid Scintillation Counter (LSC) and High Purity Germanium Gamma Spectrometry (HPGe). respectively. Concentrations of Ra-226 activity in sediment samples range from 18.93 Bg/ kg to 236.06 Bq/kg and for Ra-228 activity range from 12.59 Bg/kg to 410.60 Bq/kg. Meanwhile, concentrations of Ra-226 activity obtained in water samples range from 0.064 Bg/L to 0.199 Bq/L. These data indicate, that the distribution of Ra-228 and Ra-226 in the study area were varied from one sampling stations to another and is probably related to the contents of suspended particles.
Penentuan kepekatan aktiviti Ra-226 dan Ra-228 dalam sampel air dan sedimen dilakukan masing-masing dengan Pembilang Sintilasi Cecair (LSC) dan Spektrometri Gamma Germanium Lampau Tulen (HPGe). Kepekatan aktiviti Ra-226 dalam sampel sedimen adalah berjulat dari 18.93 Bg/kg hingga 236.06 Bq/kg dan kepekatan aktiviti Ra-228 berjulat dari 12.59 Bg/kg hingga 410.60 Bq/kg. Kepekatan aktiviti Ra-226 dalam sampel air yang diperolehi pula berjulat dari 0.064 Bg/L hingga 0.199 Bq/L. Ini menunjukkan taburan Ra-228 dan Ra-226 di kawasan kajian adalah berubah mengikut lokasi kajian dan berkemungkinan dipengaruhi oleh sifat kandungan bahan terampai.