In this paper, a novel, effective meta-heuristic, population-based Hybrid Firefly Particle Swarm Optimization (HFPSO) algorithm is applied to solve different non-linear and convex optimal power flow (OPF) problems. The HFPSO algorithm is a hybridization of the Firefly Optimization (FFO) and the Particle Swarm Optimization (PSO) technique, to enhance the exploration, exploitation strategies, and to speed up the convergence rate. In this work, five objective functions of OPF problems are studied to prove the strength of the proposed method: total generation cost minimization, voltage profile improvement, voltage stability enhancement, the transmission lines active power loss reductions, and the transmission lines reactive power loss reductions. The particular fitness function is chosen as a single objective based on control parameters. The proposed HFPSO technique is coded using MATLAB software and its effectiveness is tested on the standard IEEE 30-bus test system. The obtained results of the proposed algorithm are compared to simulated results of the original Particle Swarm Optimization (PSO) method and the present state-of-the-art optimization techniques. The comparison of optimum solutions reveals that the recommended method can generate optimum, feasible, global solutions with fast convergence and can also deal with the challenges and complexities of various OPF problems.
Energy security and environmental measurements are incomplete without renewable energy; therefore, there is a dire need to explore new energy sources. Hence, this study aimed to measure the wind power potential to generate renewable hydrogen (H2), including its production and supply cost. This study used first-order engineering model and net present value to measure the levelized cost of wind-generated renewable hydrogen by using the data source of the Pakistan Meteorological Department and State Bank of Pakistan. Results showed that the use of surplus wind and renewable hydrogen energy for green economic production is suggested as an innovative project option for large-scale hydrogen use. The key annual running expenses for hydrogen are electricity and storage costs, which have a significant impact on the costs of renewable hydrogen. The results also indicated that the project can potentially cut carbon dioxide (CO2) pollution by 139 million metric tons and raise revenue for wind power plants by US$2998.52 million. The renewable electrolyzer plants avoided CO2 at a rate of US$24.9-36.9/ton under baseload service, relative to US$44.3/ton for the benchmark. However, in the more practical mid-load situation, these plants have significant benefits. Further, the wind-generated renewable hydrogen delivers 6-11% larger annual rate of return than the standard CO2 catch plant due to their capacity to remain running and supply hydrogen to the consumer through periods of plentiful wind and heat. Also, the measured levelized output cost of hydrogen (LCOH) was US$6.22/kgH2, and for the PEC system, it was US$8.43/kgH2. Finally, it is a mutually agreed consensus among environmental scientists that the integration of renewable energy is the way forward to increase energy security and environmental performance by ensuring uninterrupted clean and green energy. This application has the potential to address Pakistan's urgent issues of large-scale surplus wind- and solar-generated energy, as well as rising energy demand.
As an abundant and fast-growing biomass, bamboo can be used as construction materials owing to its desirable physical and mechanical properties, environmentally friendly features, and alternative to replace toxic and hazardous wastes in industrial processing. In this study, grid material made from bamboo (termed 'bamboo grid') was developed and compared to commercially used polyvinyl chloride (PVC) as packing material in cooling towers; PVC packing has drawbacks such as fouling, deposit buildup, low durability, and is harmful to environments. The cooling capacity, energy efficiency and environmental impact of bamboo grid packing were evaluated via life cycle assessment (LCA), particularly the cumulative energy demand (CED) and the Building for Environmental and Economic Sustainability (BEES). Although the thermal performance of the PVC packing was found higher than that of the bamboo grid packing, the bamboo grid packing showed improved resistance characteristic, recording a total saving of 529.2 tons of standard coal during a six-month field test in a real thermal power generation plant. LCA results revealed that the utilization of bamboo-grid packing to replace PVC packing in cooling towers reduced total CED from 3420 MJ to 561 MJ per functional unit, achieving 6 times reduction. A desirable reduction ranging from 1.5 to 10.5 times was also recorded for the BEES indices. This LCA comparison analysis confirmed the improvement of energy efficiency and reduction of environmental impact by using the bamboo grid to replace PVC as packing material in cooling towers. The major environmental impact (BEES) indices (e.g., the total Global warming potential, Acidification, Eutrophication and Smog) were reduced by 1.5-10.5 times via the use of bamboo grid. The results demonstrate that bamboo grid packing is a good alternative to replace existing grid packing materials such as concrete and PVC that are harmful to human health and environments.
The political upheaval and the civil war in Libya had a painful toll on the operational reliability of the electric energy supply system. With frequent power cuts and crumbling infrastructure, mainly due to the damage inflicted upon several power plants and grid assets as well as the lack of maintenance, many Libyans are left without electricity for several hours a day. As the country has a staggeringly immense potential of solar energy, it is inevitable to exploit such potential, to avert system-wide blackouts. This paper investigates the use of small-scale PV systems in local communities as non-wires alternative (NWA), offering excess energy exchange within local/neighboring microgrids (MGs) for reliable electric power supply. Different combinations of PV/storage/diesel distributed generations (DGs), with grid-interface options, were applied on a case study of a typical dwelling in the Eastern Libyan city of Benghazi. Technical and financial feasibility assessments were carried out to contrast between various supply combinations. Sensitivity analysis of the PV-grid system was also conducted using Net Present Value (NPV) and the payback time indicators to determine the impacts of Feed-in Tariff (FiT) rates, financial incentives, electricity tariff, and inflation rate on the economic viability of the PV grid system. Results show that the PV-grid system has a promising potential under reasonable set of varying system parameters. On top of its social and environmental-friendly advantages, the PV-battery system is found to be more economical when adopted as a standalone NWA solution as compared to the diesel generator option, even at the lowest diesel price. The PV-grid system does not only provide a short-term remedy to the rolling blackouts in Libya but also enhances system operational reliability by providing a NWA to rundown or shattered grid infrastructure, thus bolstering energy provision in residential neighborhoods.
Grog is an additive material that plays important roles in ceramic making. It improves the fabrication process of green bodies as well as the physical properties of fired bodies. Few low-cost materials and wastes have found their application as grog in recent years, thus encouraging the replacement of commercial grogs with cost-saving materials. Coal fly ash, a combustion waste produced by coal-fired power plant, has the potential to be converted into grog owing to its small particle sizes and high content of silica and alumina. In this study, grog was derived from coal fly ash and mixed with kaolin clay to produce ceramics. Effects of the grog addition on the resultant ceramics were investigated. It was found that, to a certain extent, the grog addition reduced the firing shrinkage and increased the total porosity of the ceramics. The dimensional stability of the ceramics at a firing temperature of 1200 °C was also not noticeably affected by the grog. However, the grog addition in general had negative effects on the biaxial flexural strength and refractoriness of the ceramics.
Fly ash (PFA) is a complex material produced after combustion in coal-fired power plants. About half of this fly ash is disposed as solid wastes. A possible alternative to disposal of the fly ash is the synthesis of zeolite. Zeolite Boggsite (Na37Ca74Al185Si775O192 7H2O) was synthesized from fly ash by hydrothermal treatment with NaOH solutions as identified by x-ray diffraction. The zeolite type and degree of crystallization were found to be dependent on the reaction conditions and mineralogy of the raw material, particularly in terms of the relative concentrations of SiO2 and Al2O3.
A study has been carried out using a gamma-ray spectrometric system to determine the natural
radioactivity level in bricks made from industrial waste and their associated radiation hazard.
Brick-1 and brick-2 contained waste from coal power plant and granite industry, respectively. The
leachability of radionuclides from these bricks was also investigated. The activity concentration
values of 226Ra,
228Ra,
232Th, and 40K are 64.25, 63.15, 67.9 and 254.19 Bq/kg, respectively in brick-
1, and 193, 164.48, 164.63 and 1348.75 Bq/kg, respectively in brick-2. The radiation hazard
indexes such as radium equivalent activities (Raeq), representative level index (Iγr), external hazard
index (Hex) and internal hazard index (Hin) were calculated and compared with the internationally
approved values. Results indicate that brick-1 showed less radiological hazard than brick-2. This
suggested that brick-1 could be used in building construction without exceeding the proposed
criterion level.The leachability of 226Ra for bricks showed the activity concentration slightly
exceeded 1 Bq/L which is the limit generally used for industrial wastewater.
Industrial heat pumps are heat-recovery systems that allow the temperature of waste-heat stream to be increased to a higher, more efficient temperature. Consequently, heat pumps can improve energy efficiency in industrial processes as well as energy savings when conventional passive-heat recovery is not possible. In this paper, possible ways of saving energy in the chemical industry are considered, the objective is to reduce the primary energy (such as coal) consumption of power plant. Particularly the thermodynamic analyses of integrating backpressure turbine of a power plant with distillation units have been considered. Some practical examples such as conventional distillation unit and heat pump are used as a means of reducing primary energy consumption with tangible indications of energy savings. The heat pump distillation is operated via electrical power from the power plant. The exergy efficiency of the primary fuel is calculated for different operating range of the heat pump distillation. This is then compared with a conventional distillation unit that depends on saturated steam from a power plant as the source of energy. The results obtained show that heat pump distillation is an economic way to save energy if the temperature difference between the overhead and the bottom is small. Based on the result, the energy saved by the application of a heat pump distillation is improved compared to conventional distillation unit.
Anthropogenic airborne depositions of 210Po,
210Pb and 210Po/210Pb in the mosses and surface soils
collected at the vicinity of a coal-fired power plant were studied. The purpose of the study was to
determine activity concentrations of 210Po,
210Pb and 210Po/210Pb for assessing their variation
accumulation in the mosses and surface soils collected at the vicinity of a coal-fired power plant.
Other purposes were to determine their concentration factor (CF) in relation to track the potential
source of those radionuclides and to identify most suitable moss species as a biological indicator
for atmospheric deposition contaminants. In this study, different species of moss Leucobryum
aduncum, Campylopus serratus, Syrrhopodon ciliates and Vesicularia montagnei were collected in
May 2011 at the area around 15 km radius from Tanjung Bin coal-fired power plant located in
Pontian, Johor. The activity concentrations of 210Po,
210Pb and 210Po/210Pb in mosses were in the
range of 76.81 ± 4.94 – 251.33 ± 16.33 Bq/kg dry wt., 54.37 ± 3.38 – 164.63 ± 11.64 Bq/kg dry wt.
and 1.10 – 2.00, respectively. Meanwhile the ranges for those radionuclides in the surface soil
were 33.53 ± 2.10 – 179.67 ± 12.15 Bq/kg dry wt., 20.55 ± 1.33 – 106.62 ± 6.64 Bq/kg dry wt. and
1.61 – 2.44, respectively. Corresponding high ability of Leucobryum aduncum to accumulate more
210Po and 210Pb, wide geographical distribution, most abundant and high CF, therefore, the
findings can be concluded this species was the most suitable as a biological indicator for
atmospheric deposition contaminants such as 210Po and 210Pb. Furthermore, it is clear the
accumulation of 210Po and 210Pb in mosses might be supplied from various sources of atmospheric
deposition such as coal-fired power plant operation, industrial, agriculture and fertilizer activities,
burned fuel fossil and forest; and other potential sources. Meanwhile, the
The growing concern over the workers safety and health has lead many factories and organizations do the air monitoring to ensure the airborne at their workplace is safe for the worker’s health and complying the Occupational Safety and Health Act 1994 (Act 514). In this study, the monitoring covers an indoor air quality and chemical exposure to the workers in one of the power plant repair shop. A few workers from different sections namely blasting, welding, grinding, fitting and maintenance area were chosen to assist in the personal monitoring for 8 hours measurement. PM10 were measured at a few sampling points to collect dusts for 24 hours duration. The samples were brought back to the laboratory for gravimetric and SEM-EDAX analysis. The results were certainly exceed the limit for air quality, and many elements were detected such as Fe, Ni, Al, Si, Ca, K, Ba, S, Cr, Zn and Cl. The present of these elements shows that exposure to these particulate matters is quite risky and some measure needs to be taken for remedial action.
Thermoelectric nanostructures hold great promise for capturing and directly converting into electricity some vast amount of low-grade waste heats now being lost to the environment (e.g. from nuclear power plant, fossil fuel burning, automotives and household appliances). In this study, large-area vertically-aligned silicon nanowire (SiNW) arrays were synthesized in an aqueous solution containing AgN•i and HF on p-type Si (100) substrate by self-selective electroless etching process. The etching conditions were systematically varied in order to achieve different stages of nanowire formation. Diameters of the SiNWs obtained varied from approximately 50 to 200 nm and their lengths ranged from several to a few tens of um. Te/Bi2Tex.Si thermoelectric core-shell nanostructures were subsequently obtained via galvanic displacement of SiNWs in acidic HF electrolytes containing HTe02+ and 139' /HTe02+ ions. The reactions were basically a nano-electrochemical process due to the difference in redox potentials between the materials. The surface-modified SiNWs of core-shell structures had roughened surface morphologies and, therefore, higher surface-to-bulk ratios compared to unmodified SiNWs. They have potential applications in sensors, photovoltaic and thermoelectric nanodevices. Growth study on the SiNWs and core-shell nanostructures produced is presented using various microscopy, diffraction and probe-based techniques for microstructural, morphological and chemical characterizations.
Muhammad Adil Khattak, Muhammad Khairy Harmaini Shaharuddin, Muhammad Saiful Islam Haris, Muhammad Zuhaili Mohammad Aminuddin, Nik Mohamad Amirul Nik Azhar, Nik Muhammad Hakimi Nik Ahmad
It is essential to ensure the nuclear power plant system are not compromise and avoid
failure that can result in significant economic loss and physical damage to the public.
However, a very little attention was given to software and cybersecurity hazard. This
review paper discusses about the cybersecurity in nuclear power plant, history of
accident, implementation and future plan on cybersecurity deeply. About 51 published
studies (2006-2017) are reviewed in this paper. It is marked from the literature survey
articles that it is important for the cybersecurity of a nuclear power plant to be at par
with the evolution of hardware and software and to counter the increasing risk on
cyber vulnerabilities. Moreover, it should be addressed as a concern and major priority
for researches and policy-makers.
Conventional fossil fuels are relied on heavily to meet the ever-increasing demand for energy required by human activities. However, their usage generates significant air pollutant emissions, such as NOx, SOx, and particulate matter. As a result, a complete air pollutant control system is necessary. However, the intensive operation of such systems is expected to cause deterioration and reduce their efficiency. Therefore, this study evaluates the current air pollutant control configuration of a coal-powered plant and proposes an upgraded system. Using a year-long dataset of air pollutants collected at 30-min intervals from the plant's telemonitoring system, untreated flue gas was reconstructed with a variational autoencoder. Subsequently, a superstructure model with various technology options for treating NOx, SOx, and particulate matter was developed. The most sustainable configuration, which included reburning, desulfurization with seawater, and dry electrostatic precipitator, was identified using an artificial intelligence (AI) model to meet economic, environmental, and reliability targets. Finally, the proposed system was evaluated using a Monte Carlo simulation to assess various scenarios with tightened discharge limits. The untreated flue gas was then evaluated using the most sustainable air pollutant control configuration, which demonstrated a total annual cost, environmental quality index, and reliability indices of 44.1 × 106 USD/year, 0.67, and 0.87, respectively.
As a laboratory certified to ISO 9001:2008 and accredited to ISO/IEC 17025, the Secondary Standard Dosimetry Laboratory (SSDL)-Nuclear Malaysia has incorporated an overall comprehensive system for technical and quality management in promoting a reliable individual monitoring service (IMS). Faster identification and resolution of issues regarding dosemeter preparation and issuing of reports, personnel enhancement, improved customer satisfaction and overall efficiency of laboratory activities are all results of the implementation of an effective quality system. Review of these measures and responses to observed trends provide continuous improvement of the system. By having these mechanisms, reliability of the IMS can be assured in the promotion of safe behaviour at all levels of the workforce utilising ionising radiation facilities. Upgradation of in the reporting program through a web-based e-SSDL marks a major improvement in Nuclear Malaysia's IMS reliability on the whole. The system is a vital step in providing a user friendly and effective occupational exposure evaluation program in the country. It provides a higher level of confidence in the results generated for occupational dose monitoring of the IMS, thus, enhances the status of the radiation protection framework of the country.
Matched MeSH terms: Nuclear Power Plants/standards
Load shedding is some of the essential requirement for maintaining security of modern power systems, particularly in competitive energy markets. This paper proposes an intelligent scheme for fast and accurate load shedding using neural networks for predicting the possible loss of load at the early stage and neuro-fuzzy for determining the amount of load shed in order to avoid a cascading outage. A large scale electrical power system has been considered to validate the performance of the proposed technique in determining the amount of load shed. The proposed techniques can provide tools for improving the reliability and continuity of power supply. This was confirmed by the results obtained in this research of which sample results are given in this paper.
Climate change and nuclear war are currently the most dangerous challenges to human civilisation and survival. The effects of climate change are now sufficient to persuade many governments to take effective measures to reduce greenhouse gas emissions. Today there are about 27,000 nuclear warheads, many at least ten times more powerful than the Hiroshima and Nagasaki bombs, and a meaningful medical response to a nuclear attack is impossible. Nevertheless, the threat of nuclear war does not raise public concern, and indeed the nuclear-weapon states are upgrading their capability. The only effective preventive measure is the abolition of nuclear weapons. Steps towards this include: a Fissile Material Cut-off Treaty, for the nuclear weapon states to observe their obligations under the Nuclear Non-Proliferation Treaty, and for the Comprehensive Test Ban Treaty to enter into force. The ultimate need is for a Nuclear Weapons Convention; International Physicians for the Prevention of Nuclear War have launched an International Campaign to Abolish Nuclear weapons (ICAN) to promote a NWC.
Since 2011, the scientific community has worked to identify the exact transport and deposition patterns of radionuclides released from the accident at the Fukushima Daiichi Nuclear Power Plant (FDNPP) in Japan. Nevertheless, there still remain many unknowns concerning the health and environmental impacts of these radionuclides. The present paper reviews the current understanding of the FDNPP accident with respect to interactions of the released radionuclides with the environment and impacts on human and non-human biota. Here, we scrutinize existing literature and combine and interpret observations and modeling assessments derived after Fukushima. Finally, we discuss the behavior and applications of radionuclides that might be used as tracers of environmental processes. This review focuses on (137)Cs and (131)I releases derived from Fukushima. Published estimates suggest total release amounts of 12-36.7PBq of (137)Cs and 150-160PBq of (131)I. Maximum estimated human mortality due to the Fukushima nuclear accident is 10,000 (due to all causes) and the maximum estimates for lifetime cancer mortality and morbidity are 1500 and 1800, respectively. Studies of plants and animals in the forests of Fukushima have recorded a range of physiological, developmental, morphological, and behavioral consequences of exposure to radioactivity. Some of the effects observed in the exposed populations include the following: hematological aberrations in Fukushima monkeys; genetic, developmental and morphological aberrations in a butterfly; declines in abundances of birds, butterflies and cicadas; aberrant growth forms in trees; and morphological abnormalities in aphids. These findings are discussed from the perspective of conservation biology.
Coal combustion by-products (CCPs) (i.e. fly (FA) and bottom (BA) ashes) generated by power plants contain heavy metals. This research presents leaching properties of coal ashes (FA and BA) collected from Jimah coal-fired power station, Port Dickson, Negeri Sembilan using USEPA standard methods namely toxicity characteristic leaching procedure (TCLP), and synthetic precipitation leaching procedure (SPLP). Heavy metals like lead (Pb), zinc (Zn), copper (Cu) and arsenic (As) were quantified using atomic absorption spectrometer (AAS). The leached of heavy metals fluxes were Cu < Zn < Pb < As. As leached the most whilst indicating of possible contamination from As. Overall, the ranges of leached concentration were adhered to permissible limits of hazardous waste criteria for metal (Pb and As) and industrial effluent (Zn and Cu). The presented data has potential reuse as reference for the coal ash concrete mixed design application in construction industries.
Since the world’s first nuclear reactor major breakthrough in December 02, 1942, the nuclear power industry has undergone tremendous development and evolution for more than half a century. After surpassing moratorium of nuclear power plant construction caused by catastrophic accidents at Three-Mile Island (1979) and Chernobyl (1986), today, nuclear energy is back on the policy agendas of many states, both developed and developing nations, signaling nuclear revival or nuclear renaissance. Selection of suitable nuclear power technology has thus been subjected to primary attention. This short paper attempts to draw preliminary technology assessment for the first nuclear power reactor technology for Malaysia. Methodology employed is qualitative analysis collating recent finding of TNB-KEPCO Preliminary Feasibility Study for Nuclear Power Program in Peninsular Malaysia and other published presentations and/or papers by multiple experts.
The results suggested that the pressurized water reactor (PWR) is the prevailing technology in terms of numbers and plant performances, and while the commercialization of Gen IV reactors is remote (e.g. not until 2030), Generation III/III+ NPP models are commercially available on the market today. Five (5) major steps involved in reactor technology selection were introduced with a focus on introducing important aspects of selection criteria. Three (3) categories for the of reactor technology selection were used for the cursory evaluation. The outcome of these analyses shall constitute deeper and full review analyses of the recommended reactor technologies for the intended full feasibility study in the near future. Recommendations for reactor technology option were also provided for both strategic and technical recommendations. The paper shall also postulate or rather implore what could be the best way for Malaysian and also other aspiring new entrant nations to select systematically their first civilian nuclear power reactor.
Template-assisted growth is an important nanoelectrochemical deposition technique for synthesizing one-dimensional (1-D) nanostructures with uniformly well-controlled shapes and sizes. A good template with well-defined dimensions is imperative for realizing this task. Porous anodic alumina (PAA) has been a favorable candidate for this purpose as it can be tailor-made with precise pore geometries, such as pore length and diameter as well as inter-pore distances, via the anodisation of pure aluminium. This paper reports the fabrication of PAA templates and electrochemical synthesis of functional nanostructures in the form of nanowires using PAA templates as scaffolds. Axial heterostructured and homogeneous nanowires formed by engineering materials configuration via composition and/or layer thickness variations were fabricated for different functionalities. X-ray diffraction and imaging techniques were used to elucidate the microstructures, morphologies and chemical compositions of the nanowires produced. Due to their large surface area-to-volume ratios, and therefore high sensitivities, these functional nanostructures have useful applications as critical components in nanosensor devices and various areas of nanotechnology. Potential applications include as hydrogen gas sensors in nuclear power plant for monitoring structural integrity of reactor components and containment building, as well as environmental monitoring of air pollution and leakages of toxic gases and chemicals.