Calcium silicate (CaSiO3, CS) ceramic composites reinforced with graphene nanoplatelets (GNP) were prepared using hot isostatic pressing (HIP) at 1150°C. Quantitative microstructural analysis suggests that GNP play a role in grain size and is responsible for the improved densification. Raman spectroscopy and scanning electron microscopy showed that GNP survived the harsh processing conditions of the selected HIP processing parameters. The uniform distribution of 1 wt.% GNP in the CS matrix, high densification and fine CS grain size help to improve the fracture toughness by ∼130%, hardness by ∼30% and brittleness index by ∼40% as compared to the CS matrix without GNP. The toughening mechanisms, such as crack bridging, pull-out, branching and deflection induced by GNP are observed and discussed. The GNP/CS composites exhibit good apatite-forming ability in the simulated body fluid (SBF). Our results indicate that the addition of GNP decreased pH value in SBF. Effect of addition of GNP on early adhesion and proliferation of human osteoblast cells (hFOB) was measured in vitro. The GNP/CS composites showed good biocompatibility and promoted cell viability and cell proliferation. The results indicated that the cell viability and proliferation are affected by time and concentration of GNP in the CS matrix.
A few studies in animals and a study in humans showed a positive effect of probiotic on bone metabolism and bone mass density. Most of the investigated bacteria were Lactobacillus and Bifidobacterium. The positive results of the probiotics were supported by the high content of dietary calcium and the high amounts of supplemented probiotics. Some of the principal mechanisms include (1) increasing mineral solubility due to production of short chain fatty acids; (2) producing phytase enzyme by bacteria to overcome the effect of mineral depressed by phytate; (3) reducing intestinal inflammation followed by increasing bone mass density; (4) hydrolysing glycoside bond food in the intestines by Lactobacillus and Bifidobacteria. These mechanisms lead to increase bioavailability of the minerals. In conclusion, probiotics showed potential effects on bone metabolism through different mechanisms with outstanding results in the animal model. The results also showed that postmenopausal women who suffered from low bone mass density are potential targets to consume probiotics for increasing mineral bioavailability including calcium and consequently increasing bone mass density.
To evaluate physical properties and cytotoxicity of pure gypsum-based (pure-GYP) and experimental gypsum-based biomaterials mixed with polyacrylic acid (Gyp-PA). The results were compared with calcium hydroxide (CH) and glass ionomer cement (GIC) for application as base/liner materials.
Crack formation in concrete is one of the main reasons for concrete degradation. Calcium alginate capsules containing biological self-healing agents for cementitious materials were studied for the self-healing of cement paste and mortars through in vitro characterizations such as healing agent survivability and retention, material stability, and biomineralization, followed by in situ self-healing observation in pre-cracked cement paste and mortar specimens. Our results showed that bacterial spores fully survived the encapsulation process and would not leach out during cement mixing. Encapsulated bacteria precipitated CaCO3 when exposed to water, oxygen, and calcium under alkaline conditions by releasing CO32- ions into the cement environment. Capsule rupture is not required for the initiation of the healing process, but exposure to the right conditions are. After 56 days of wet-dry cycles, the capsules resulted in flexural strength regain as high as 39.6% for the cement mortar and 32.5% for the cement paste specimens. Full crack closure was observed at 28 days for cement mortars with the healing agents. The self-healing system acted as a biological CO32- pump that can keep the bio-agents retained, protected, and active for up to 56 days of wet-dry incubation. This promising self-healing strategy requires further research and optimization.
Hydroxyapatite (HA) powder was synthesized via wet method using calcium nitrate hydrate (Ca(NO3)2.H2O) and diammonium hydrogen phosphate ((NH4)2HPO4) as raw materials. Powder obtained was milled using various milling speed ranging from 250 to 400 r.p.m. and sintered at 1300°C for 2hrs. Due to the nature of HA powder that decomposed at high temperature, XRD technique have been used in this work to determine the phase composition of the HA powder and also the crystallite size. The unmilled sample was used as the control group. Results show that sufficient heat supply generated from the milling process, initiates the decomposition of HA phase into ȕ-tricalcium phosphate (ȕ-TCP). Decomposition of HA starts to occur at the milling speed of 300 rpm, i.e the formation of ȕ-TCP was occurred at lower sintering temperature. It was believed that the decomposition of HA was associated with the formation of an intermediate phase, oxyapatite. Moreover, the crystallinity and particle size of the produced powder is very much affected by the milling speed and the stability of the HA. All milled powders possess spherical shape particle.
The aims of this study were to examine the effect of salts (CaCl2, CaSO4 and MgSO4) on the rheological and thermal properties of gelatin extracted from the skins of tropical fishes, sin croaker (Johnius dussumeiri) and shortfin scad (Decapterus macrosoma). It was found that the melting temperatures of fish skin gelatins were increased by 1.5 times as compared to bovine gelatin which was only increased by 0.5 times after holding for 2 h at 5°C. The storage (G’) and loss (G”) modulus of fish skin gelatins were improved with the addition of calcium sulphate (CaSO4) and magnesium sulphate (MgSO4), respectively. However, the storage (G’) and loss (G”) modulus of gelatin solutions were decreased with the addition of calcium chloride (CaCl2). Magnesium sulphate (MgSO4) was found to be an effective salt to improve the bloom value, elastic and viscous moduli of the fish skin gelatin. This study showed that shortfin scad skin gelatin with salt addition possessed better thermal and rheological properties than sin croaker gelatin.
Introducing CO2 flux as the carbonate source had an effect on the carbonate content of carbonate apatite (CAp) synthesized by solid state reaction. The reactants were CaCO3 and beta-tricalcium phosphate (β-TCP) and the heat treatment in air was performed at 1250ºC followed by instant cooling in CO2 flux for temperatures ranging from 800ºC room temperature (RT) . The influence of CO2 flux at various temperature drop differences in the cooling process (1250ºC RT, 1250ºC–500ºC, 1250ºC–600ºC, 1250ºC–700ºC, and 1250ºC–800ºC) was tested to optimize the carbonation degree and subsequent effects on the physical and mechanical properties of CAp. Thermally treated samples revealed an increasing degree of carbonation, achieving a maximum of 5.2 wt% at the highest (1250ºC RT) and a minimum of 2.7 wt% at the lowest (1250ºC–800ºC) temperature drop differences, respectively. This showed that the carbonate content was correlated with the increase in exposure to CO2 flux. However, consistent compressive strength, tensile strength, density and porosity were observed against increasing temperature drop differences which indicated that the degree of carbonation exerted no influence on the physical and mechanical properties of CAp. This method enabled the synthesis of solid state CAp simply by exposing calcium phosphate mixtures to CO2 flux. It also allowed the control of carbonate content for desired medical applications.
In this study, the effect of beverages (Coke TM, Sprite™, Ribena™, Chrysanthemum tea and mineral water) on the demineralisation of the enamel surface was investigated. Demineralisation was determined by the rate of calcium released from the enamel surface on exposure to the beverages. Calcium was determined using the EDTA titration method. The pH of these beverages was measured using a pH meter and found to be in the acidic range (2.43 to 5.79) while mineral water which served as a control has a pH of 7.00. Ii was found that the rate of calcium released from Coke™(0.76 J..lg/min) showed a significant mean difference from Sprite™ (0.38 J..lg/min), Chrysanthemum tea (0.10 J..lg/min) and mineral water (0.00 J..lg/min)at p< .05, but was however not significantly different from Ribena™. Likewise, Chrysanthemum tea and mineral water also showed statistically no significant mean difference in the released of calcium during the study period. The results obtained in this study indicated that beverages with low pH may pose detrimental effect on the enamel surface which could have clinical implication, especially in people with salivary gland dysfunction or low salivary flow.
Thermodynamic and kinetic parameters of catalytic pyrolysis of rice hull (RH) pyrolysis using two different types of renewable catalysts namely natural limestone (LS) and eggshells (ES) using thermogravimetric analysis (TG) approach at different heating rates of 10-100 K min-1 in temperature range of 323-1173 K are investigated. Catalytic pyrolysis mechanism of both catalysts had shown significant effect on the degradation of RH. Model free kinetic of iso-conversional method (Flynn-Wall-Ozawa) and multi-step reaction model (Distributed Activation Energy Model) were employed into present study. The average activation energy was found in the range of 175.4-177.7 kJ mol-1 (RH), 123.3-132.5 kJ mol-1 (RH-LS), and 96.1-100.4 kJ mol-1 (RH-ES) respectively. The syngas composition had increased from 60.05 wt% to 63.1 wt% (RH-LS) and 63.4 wt% (RH-ES). However, the CO2 content had decreased from 24.1 wt% (RH) to 20.8 wt% (RH-LS) and 19.9 wt% (RH-ES).
The data in this article contain supporting evidence for the research manuscript entitled "Bronchodilator effects of Lignosus rhinocerotis extract on rat isolated airways is linked to the blockage of calcium entry" by Lee et al. (2018) [1]. The data were obtained by calcium imaging technique with fluorescent calcium indicator dyes, Fura 2-AM, to visualize calcium ion movement in the rat dorsal ganglion (DRG) cells. The effects of L. rhinocerotis cold water extract (CWE1) on intracellular calcium levels in the DRG cells were presented.
Mining waste that is rich in iron-, calcium- and magnesium-bearing minerals can be a potential feedstock for sequestering CO2 by mineral carbonation. This study highlights the utilization of iron ore mining waste in sequestering CO2 under low-reaction condition of a mineral carbonation process. Alkaline iron mining waste was used as feedstock for aqueous mineral carbonation and was subjected to mineralogical, chemical, and thermal analyses. A carbonation experiment was performed at ambient CO2 pressure, temperature of 80 °C at 1-h exposure time under the influence of pH (8-12) and particle size (
Mining activities have often been associated with the issues of waste generation, while mining is considered a carbon-intensive industry that contributes to the increasing carbon dioxide emission to the atmosphere. This study attempts to evaluate the potential of reusing mining waste as feedstock material for carbon dioxide sequestration through mineral carbonation. Characterization of mining waste was performed for limestone, gold and iron mine waste, which includes physical, mineralogical, chemical and morphological analyses that determine its potential for carbon sequestration. The samples were characterized as having alkaline pH (7.1-8.3) and contain fine particles, which are important to facilitate precipitation of divalent cations. High amount of cations (CaO, MgO and Fe2O3) was found in limestone and iron mine waste, i.e., total of 79.55% and 71.31%, respectively, that are essential for carbonation process. Potential Ca/Mg/Fe silicates, oxides and carbonates have been identified, which was confirmed by the microstructure analysis. The limestone waste composed majorly of CaO (75.83%), which was mainly originated from calcite and akermanite minerals. The iron mine waste consisted of Fe2O3 (56.60%), mainly from magnetite and hematite, and CaO (10.74%) which was derived from anorthite, wollastonite and diopside. The gold mine waste was attributed to a lower cation content (total of 7.71%), associated mainly with mineral illite and chlorite-serpentine. The average capacity for carbon sequestration was between 7.73 and79.55%, which corresponds to 383.41 g, 94.85 g and 4.72 g CO2 that were potentially sequestered per kg of limestone, iron and gold mine waste, respectively. Therefore, it has been learned that the mine waste might be utilized as feedstock for mineral carbonation due to the availability of reactive silicate/oxide/carbonate minerals. Utilization of mine waste would be beneficial in light of waste restoration in most mining sites while tackling the issues of CO2 emission in mitigating the global climate change.
The Damoh district, which is located in the central India and characterized by limestone, shales, and sandstone compact rock. The district has been facing groundwater development challenges and problems for several decades. To facilitate groundwater management, it is crucial to monitoring and planning based on geology, slope, relief, land use, geomorphology, and the types of the basaltic aquifer in the drought-groundwater deficit area. Moreover, the majority of farmers in the area are heavily dependent on groundwater for their crops. Therefore, delineation of groundwater potential zones (GPZ) is essential, which is defined based on various thematic layers, including geology, geomorphology, slope, aspect, drainage density, lineament density, topographic wetness index (TWI), topographic ruggedness index (TRI), and land use/land cover (LULC). The processing and analysis of this information were carried out using Geographic Information System (GIS) and Analytic Hierarchy Process (AHP) methods. The validity of the results was trained and tested using Receiver Operating Characteristic (ROC) curves, which showed training and testing accuracies of 0.713 and 0.701, respectively. The GPZ map was classified into five classes such as very high, high, moderate, low, and very low. The study revealed that approximately 45% of the area falls under the moderate GPZ, while only 30% of the region is classified as having a high GPZ. The area receives high rainfall but has very high surface runoff due to no proper developed soil and lack of water conservation structures. Every summer season show a declined groundwater level. In this context, results of study area are useful to maintain the groundwater under climate change and summer season. The GPZ map plays an important role in implementing artificial recharge structures (ARS), such as percolation ponds, tube wells, bore wells, cement nala bunds (CNBs), continuous contour trenching (CCTs), and others for development of ground level. This study is significant for developing sustainable groundwater management policies in semi-arid regions, that are experiencing climate change. Proper groundwater potential mapping and watershed development policies can help mitigate the effects of drought, climate change, and water scarcity, while preserving the ecosystem in the Limestone, Shales, and Sandstone compact rock region. The results of this study are essential for farmers, regional planners, policy-makers, climate change experts, and local governments, enabling them to understand the groundwater development possibilities in the study area.
Excitotoxicity arises from unusually excessive activation of excitatory amino acid receptors such as glutamate receptors. Following an energy crisis, excitotoxicity is a major cause for neuronal death in neurological disorders. Many glutamate antagonists have been examined for their efficacy in mitigating excitotoxicity, but failed to generate beneficial outcome due to their side effects on healthy neurons where glutamate receptors are also blocked. In this study, we found that during chronic hypoxia there is upregulation and activation of a nonselective cation channel TRPM4 that contributes to the depolarized neuronal membrane potential and enhanced glutamate-induced calcium entry. TRPM4 is involved in modulating neuronal membrane excitability and calcium signaling, with a complex and multifaceted role in the brain. Here, we inhibited TRPM4 using a newly developed blocking antibody M4P, which could repolarize the resting membrane potential and ameliorate calcium influx upon glutamate stimulation. Importantly, M4P did not affect the functions of healthy neurons as the activity of TRPM4 channel is not upregulated under normoxia. Using a rat model of chronic hypoxia with both common carotid arteries occluded, we found that M4P treatment could reduce apoptosis in the neurons within the hippocampus, attenuate long-term potentiation impairment and improve the functions of learning and memory in this rat model. With specificity to hypoxic neurons, TRPM4 blocking antibody can be a novel way of controlling excitotoxicity with minimal side effects that are common among direct blockers of glutamate receptors.
To replace the obsolete ponding system, palm oil mill effluent (POME) steam reforming (SR) over net-acidic LaNiO3 and net-basic LaCoO3 were proposed as the POME primary treatments, with promising H2-rich syngas production. Herein, the long-term evaluation of POME SR was scrutinized with both catalysts under the optimal conditions (600 °C, 0.09 mL POME/min, 0.3 g catalyst, & 74-105 μm catalyst particle size) to examine the catalyst microstructure changes, transient process stability, and final effluent evaluation. Extensive characterization proved the (i) adsorption of POME vapour on catalysts before SR, (ii) deposition of carbon and minerals on spent SR catalysts, and (iii) dominance of coking deactivation over sintering deactivation at 600 °C. Despite its longer run, spent LaCoO3 (50.54 wt%) had similar carbon deposition with spent LaNiO3 (50.44 wt%), concurring with its excellent coke resistance. Spent LaCoO3 (6.12 wt%; large protruding crystals) suffered a harsher mineral deposition than spent LaNiO3 (3.71 wt%; thin film coating), confirming that lower reactivity increased residence time of reactants. Transient syngas evolution of both SR catalysts was relatively steady up to 4 h but perturbed by coking deactivation thereafter. La2O2CO3 acted as an intermediate species that hastened the coke removal via reverse Boudouard reaction upon its decarbonation. La2O2CO3 decarbonation occurred continuously in LaCoO3 system but intermittently in LaNiO3 system. LaNiO3 system only lasted for 13 h as its compact ash blocked the gas flow. LaCoO3 system lasted longer (17 h) with its porous ash, but it eventually failed because KCl crystallites blocked its active sites. Relatively, LaCoO3 system offered greater net H2 production (72.78%) and POME treatment volume (30.77%) than LaNiO3 system. SR could attain appreciable POME degradation (>97% COD, BOD5, TSS, & colour intensity). Withal, SR-treated POME should be polished to further reduce its incompliant COD and BOD5.
Trace and minor elements play crucial roles in a variety of biological processes, including amyloid fibrils formation. Mechanisms include activation or inhibition of enzymatic reactions, competition between elements and metal proteins for binding positions, also changes to the permeability of cellular membranes. These may influence carcinogenic processes, with trace and minor element concentrations in normal and amyloid tissues potentially aiding in cancer diagnosis and etiology. With the analytical capability of the spectroscopic technique X-ray fluorescence (XRF), this can be used to detect and quantify the presence of elements in amyloid characterization, two of the trace elements known to be associated with amyloid fibrils. In present work, involving samples from a total of 22 subjects, samples of normal and amyloid-containing tissues of heart, kidney, thyroid, and other tissue organs were obtained, analyzed via energy-dispersive X-ray fluorescence (EDXRF). The elemental distribution of potassium (K), calcium (Ca), arsenic (As), and iron (Fe) was examined in both normal and amyloidogenic tissues using perpetual thin slices. In amyloidogenic tissues the levels of K, Ca, and Fe were found to be less than in corresponding normal tissues. Moreover, the presence of As was only observed in amyloidogenic samples; in a few cases in which there was an absence of As, amyloid samples were found to contain Fe. Analysis of arsenic in amyloid plaques has previously been difficult, often producing contradictory results. Using the present EDXRF facility we could distinguish between amyloidogenic and normal samples, with potential correlations in respect of the presence or concentration of specific elements.
Nickel hyperaccumulator plants play a major role in nickel recycling in ultramafic ecosystems, and under agromining the nickel dynamics in the farming system will be affected by removal of nickel-rich biomass. We investigated the biogeochemical cycling of nickel as well as key nutrients in an agromining operation that uses the metal crop Phyllanthus rufuschaneyi in the first tropical metal farm located in Borneo (Sabah, Malaysia). For two years, this study monitored nine 25-m2 plots and collected information on weather, biomass exportation, water, and litter fluxes to the soil. Without harvesting, nickel inputs and outputs had only minor contributions (<1 %) to the total nickel budget in this system. The nickel cycle was mainly driven by internal fluxes, particularly plant uptake, litterfall and throughfall. After two years of cropping, the nickel litter flux corresponded to 50 % of the total nickel stock in the aerial biomass (3.1 g m-2 year-1). Nickel was slowly released from the litter; after 15 months of degradation, 60 % of the initial biomass and the initial nickel quantities were still present in the organic layer. Calcium, phosphorus and potassium budgets in the system were negative without fertilisation. Unlike what is observed for nickel, sustained agromining would thus lead to a strong depletion of calcium stocks if mineral weathering cannot replenish it.
Hypertension is highly prevalent worldwide and is the major risk factor for heart failure (HF). More than half of the patients with HF in Asia suffer from hypertension. According to the 2022 American Heart Association/American College of Cardiology/Heart Failure Society of America HF guideline, there are four stages of HF, including at risk for HF (stage A), pre-HF (stage B), symptomatic HF (stage C), and advanced HF (stage D). Given the high prevalence of hypertension as well as HF and the stronger association between hypertension and cardiovascular diseases in Asians compared to the west, measures to prevent and alleviate the progression to clinical HF, especially controlling the blood pressure (BP), are of priority for Asian populations. After reviewing evidence-based studies, we propose a BP target of less than 130/80 mmHg for patients at stages A, B, and C. However, relatively higher BP may represent an opportunity to maximize guideline-directed medical therapy (GDMT), which could potentially result in a better prognosis for patients at stage D. Traditional antihypertensive drugs are the cornerstones for the management of hypertension at stages A and B. Notably, calcium channel blockers (CCBs) are inferior to other drug classes for the preventing of HF, whereas diuretics are superior to others. For patients at stage C, GDMT is essential which also helps the control of BP. In particular, sodium-glucose cotransporter-2 (SGLT2) inhibitors are newer therapies recommended for the treatment of HF and presumably even in hypertension to prevent HF. Regarding patients at stage D, GDMT is also recommended if tolerable and measures should be taken to improve hemodynamics.
Matched MeSH terms: Calcium Channel Blockers/therapeutic use
Soybean milk is a rich plant-based source of protein, and phenolic compounds. This study compared the nutritional value of soybean milk, flour, soy protein isolate (SPI) and evaluated the impact of prepared vitamin E/calcium salt/soy protein isolate nanoparticles (ECSPI-NPs) on fortification of developed soybean milk formulations. Results indicated that soybean flour protein content was 40.50 g/100 g, that fulfills 81% of the daily requirement (DV%), the unsaturated fatty acids (USFs), oleic and linoleic content was 21.98 and 56.7%, respectively, of total fatty acids content. In soybean milk, essential amino acids, threonine, leucine, lysine achieved 92.70, 90.81, 77.42% of amino acid scores (AAS) requirement values respectively. Ferulic acid was the main phenolic compound in soybean flour, milk and SPI (508.74, 13.28, 491.78 µg/g). Due to the moisture content of soybean milk (88.50%) against (7.10%) in soybean flour, the latest showed higher nutrients concentrations. The prepared calcium (20 mM/10 g SPI) and vitamin E (100 mg/g SPI) nanoparticles (ECSPI-NPs) exhibited that they were effectively synthesized under transmission electron microscope (TEM), stability in the zeta sizer analysis and safety up to IC50 value (202 ug/mL) on vero cell line. ECSPI-NPs fortification (NECM) enhanced significantly phenolic content (149.49 mg/mL), taste (6.10), texture (6.70) and consumer overall acceptance (6.54). Obtained results encourage the application of the prepared ECSPI-NPs for further functional foods applications.
Methylene blue (MB) was regarded as a highly toxic and hazardous substance owing to its irreparable hazard and deplorable damage on the ecosystem and the human body. The treatment of this colorant wastewater appeared to be one of the towering challenges in wastewater treatment. In this study, a microbial fuel cell coupled with constructed wetland (CW-MFC) with effective MB elimination and its energy recuperation concurrently based on the incorporation of carbide lime as a substrate in a new copper oxide-loaded on carbon cloth (CuO/CC) cathode system was studied. The crucial influencing parameters were also delved, and the MB degradation and chemical oxygen demand (COD) removal efficiencies were correspondingly incremented by 97.3% and 89.1% with maximum power output up to 74.1 mW m-2 at optimal conditions (0.2 g L-1 carbide lime loading and 500 Ω external resistance). The carbide lime with high calcium ion content was greatly conducive for the enrichment of critical microorganism and metabolic activities. The relative abundances of functional bacteria including Proteobacteria and Actinobacteriota were vividly increased. Moreover, the impressive results obtained in printed ink wastewater treatment with a COD removal efficiency of 81.3% and a maximum power density of 58.2 mW m-2, which showcased the potential application of CW-MFC.