MyMedR

Displaying publications 41 - 60 of 148 in total

Abstract:

Sort:

Production of biodiesel from palm fatty acid distillate by microwave-assisted sulfonated glucose acid catalyst

Nur Nazlina Saimon, Heng Khuan Eu, Anwar Johari, Norzita Ngadi, Mazura Jusoh, Zaki Yamani Zakaria

Sains Malaysiana, 2018;47:109-115.

Biodiesel, one of the renewable energy sources has gained attention for decades as the alternative fuel due to its remarkable properties. However, there are several drawbacks from the industrial production of biodiesel such as the spike in the production cost, environmental issues related to the usage of homogeneous catalyst and profitability in long term. One of the solutions to eliminate the problem is by utilizing low cost starting material such as palm fatty acid distillate (PFAD). PFAD is a byproduct from the refining of crude palm oil and abundantly available. Esterification of PFAD to biodiesel will be much easier with the presence of heterogeneous acid catalyst. Most of acid catalyst preparation involves series of heating process using conventional method. In this study, microwave was utilized in catalyst preparation, significantly reducing the reaction time from conventional heating method. The catalyst produced was characterized using X-Ray Diffraction (XRD), Brunauer Emmet and Teller (BET), Scanning Electron Microscopy (SEM), Temperature-Programmed Desorption - Ammonia (TPD-NH3) and Fourier Transform Infrared (FTIR) while percentage yield and conversion of the PFAD were analysed by gas chromatography - flame ionization detector (GC-FID) and acid-base titration, respectively. It has been demonstrated that the percentage yield of biodiesel from the PFAD by employing sulfonated glucose acid catalyst (SGAC) reached 98.23% under the following conditions: molar ratio of methanol to PFAD of 10:1, catalyst loading of 2.5% and reaction temperature of 70oC. The microwave-assisted SGAC showed its potential to replace the SGAC produced via conventional heating method.

Matched MeSH terms: Heating
Processing of fresh palm fruits using microwaves

Chow MC, Ma AN

J Microw Power Electromagn Energy, 2007;40(3):165-73.
PMID: 17645207

Microwave heating was determined in this study to be suitable for the detachment and drying of palm fruits from whole bunches, cut bunches and spikelets. Microwave treatment of the palm fruits was able to attain the objectives of conventional fresh palm fruits sterilization processeses such as fruit softening, nut conditioning and halting of enzymatic lipolysis. Palm oil and kernel oil solvent extracted respectively from the microwave treated whole fruits and kernel were found to have a good quality of low free fatty acid content. This technology, together with the solvent extraction of the dehydrated fruits, may have the potential to be a continuous, dry and clean technology for palm oil milling.

Matched MeSH terms: Heating/methods*
Preparation of activated carbon by microwave heating of langsat (Lansium domesticum) empty fruit bunch waste

Foo KY, Hameed BH

Bioresour Technol, 2012 Jul;116:522-5.
PMID: 22595094 DOI: 10.1016/j.biortech.2012.03.123

The feasibility of langsat empty fruit bunch waste for preparation of activated carbon (EFBLAC) by microwave-induced activation was explored. Activation with NaOH at the IR ratio of 1.25, microwave power of 600 W for 6 min produced EFBLAC with a carbon yield of 81.31% and adsorption uptake for MB of 302.48 mg/g. Pore structural analysis, scanning electron microscopy and Fourier transform infrared spectroscopy demonstrated the physical and chemical characteristics of EFBLAC. Equilibrium data were best described by the Langmuir isotherm, with a monolayer adsorption capacity of 402.06 mg/g, and the adsorption kinetics was well fitted to the pseudo-second-order equation. The findings revealed the potential to prepare high quality activated carbon from langsat empty fruit bunch waste by microwave irradiation.

Matched MeSH terms: Heating/methods*
Fulltext Prenatal ultrasound heating impacts on fluctuations in haematological analysis of Oryctolagus cuniculus

Ahmad Zaiki FW, Md Dom S, Abdul Razak HR, Hassan HF

Quant Imaging Med Surg, 2013 Oct;3(5):262-8.
PMID: 24273744 DOI: 10.3978/j.issn.2223-4292.2013.10.05

Prenatal Ultrasound (US) is commonly used as a routine procedure on pregnant women. It is generally perceived as a safe procedure due to the use of non-ionizing radiation. However, the neurotoxicity of diagnostic prenatal US was detected to have a correlation with high susceptibility to early developing fetus. This research involved in vivo experimental model by using 3(rd) trimester pregnant Oryctolagus cuniculus and exposing them to US exposures for 30, 60, and 90 minutes at their gestational day (GD) 28-29. The output power and intensities, spatial peak temporal average intensity (ISPTA) of US were varied from 0.4 to 0.7 W and 0.13 to 0.19 W/cm(2) respectively were tested initially in free-field, water. Haematological analysis was carried out to detect any changes in blood constituents. Statistically significant differences were detected in red blood cell (RBC) count (P<0.001), haemoglobin (Hb) concentration (P<0.001) and also platelet (PLT) count (P<0.001) in newborn of Oryctolagus cuniculus. These findings indicate the possibility of US heating in causing defects on studied animal.

Matched MeSH terms: Heating
Fulltext Preheated (Heat-Assisted) Clinching Process for Al/CFRP Cross-Tension Specimens

Lin PC, Fang JC, Lin JW, Tran XV, Ching YC

Materials (Basel), 2020 Sep 19;13(18).
PMID: 32961763 DOI: 10.3390/ma13184170

Effects of processing parameters on preheated (heat-assisted) clinching process to join aluminum alloy 5052-H32 (AA5052) and thermoplastic carbon-fiber-reinforced-plastic (TP-CFRP) sheets for cross-tension (CT) specimens were first studied. Preheating was critical since brittle TP-CFRP could be softened to avoid fracturing or cracking during clinching process. Four processing parameters, including punching force, die depth, heating mode, and heating temperature, were considered. Quasi-static tests and microscope observations were taken to evaluate AA5052/TP-CFRP clinch joints in CT specimens and determine appropriate processing parameters for fatigue tests. Finally, fatigue data and failure mode of clinch joints in CT specimens were obtained and discussed.

Matched MeSH terms: Heating
Plasma-sprayed coating of hydroxyapatite on metal implants--a review

Talib RJ, Toff MR

Med J Malaysia, 2004 May;59 Suppl B:153-4.
PMID: 15468864

Metal implants such as titanium, stainless steel and Co-Cr-Mo are used for load bearing purposes such as hip joint prostheses, fixing plates and dental root implants. For practical application, plasma-sprayed coatings of hydroxyapatite (HA) on metal implants are applied to promote early formation of strong bonds between metal implant and living bone. Plasma spray coating involves heating of HA material to a semi-molten or molten state and then propels its to a metal substrate. The plasma flame temperature is in the range of 6,000 degrees C to 16,000 degrees C but the surface temperature of the substrate rarely exceeds 150 degrees C. The HA materials are feed into the spray gun in the form of powders. Furthermore, this paper will discuss the processes of plasma-sprayed coating of HA on various types of metal implants.

Matched MeSH terms: Heating
Fulltext Physicochemical properties of margarines enriched with medium- and long-chain triacylglycerol

Arifin, N., Cheong, L.Z., Koh, S.P., Long, K., Tan, C.P., Yusoff, M.S.A., et al.

ASM Science Journal, 2010;4(2):113-122.
MyJurnal

Several binary and ternary medium- and long-chain triacylglycerol (MLCT)-enriched margarine formulations were examined for their solid fat content, heating profile, polymorphism and textural properties. MLCT feedstock was produced through enzymatic esterification of capric and stearic acids with glycerol. The binary formulations were produced by mixing MLCT feedstock blend (40%–90%) and palm olein (10%–60%) with 10% increments (w/w). Solid fat profiles of commercial margarines were used as a reference to determine the suitability of the formulations for margarine production. The solid fat content of the binary formulations of MO 82 and MO 91 (M, MLCT, O, palm olein) were similar to the commercial margarines at 25°C which met the basic requirement for efficient dough consistency. Ternary formulations using reduced MLCT feedstock blend proportion (from 80%–90% to 60%–70%) were also developed. The reduction of MLCT feedstock blend was
done as it had the highest production cost (3USD/kg) in comparison to palm olein (0.77USD/kg) and palm stearin (0.7USD/kg). The proportions of 5%–15% of palm stearin were substituted with palm olein in MO 64 and MO 73 (M, MLCT; O, palm olein) formulations with 5% increment (w/w). As a result, MOS 702010 and MOS 603010 (M, MLCT; O, palm olein; S, palm stearin) margarine formulations showed similar SFC % to the commercial margarines at 25ºC. These formulations were subsequently chosen to produce margarines. The onset melting and complete melting points of MLCT-enriched margarine formulations were high (51.04ºC –57.93ºC) due to the presence of a high amount of long chain saturated fatty acids. Most of the formulations showed β΄- crystals. MOS 702010 was selected as the best formulation due to values for textural parameters comparable (P

Matched MeSH terms: Heating
Performance of cellulose acetate - polyethersulphone blend membrane prepared using microwave heating for palm oil mill effluent treatment

Idris A, Ahmed I, Jye HW

Water Sci Technol, 2007;56(8):169-77.
PMID: 17978445

The objective of this research is to investigate the performance of blend cellulose acetate (CA)-polyethersulphone (PES) membranes prepared using microwave heating (MWH) techniques and then compare it with blend CA-PES membranes prepared using conventional heating (CH) methods using bovine serum albumin solution. The superior membranes were then used in the treatment of palm oil mill effluent (POME). Various blends of CA-PES have been blended with PES in the range of 1-5 wt%. This distinctive series of dope formulations of blend CA/PES and pure CA was prepared using N, N-dimethylformamide (DMF) as solvent. The dope solution was prepared by MW heating for 5 min at a high pulse and the membranes were prepared by phase inversion method. The performances of these membranes were evaluated in terms of pure water and permeate flux, percentage removal of total suspended solids (TSS), chemical oxygen demand (COD) and biochemical oxygen demand (BOD). The results indicate that blend membranes prepared using the microwave technique is far more superior compared to that prepared using CH. Blend membranes with 19% CA, 1-3% PES and 80% of DMF solvent were found to be the best membrane formulation.

Matched MeSH terms: Heating
Fulltext Passive Warming using a Heat-Band versus a Resistive Heating Blanket for the Prevention of Inadvertent Perioperative Hypothermia during Laparotomy for Gynaecological Surgery

Wan Fadzlina WM, Wan Mohd Nazaruddin WH, Rhendra Hardy MZ

Malays J Med Sci, 2016 Mar;23(2):28-37.
PMID: 27547112 MyJurnal

Inadvertent perioperative hypothermia (IPH) is a common problem, despite advancements in a variety of warming systems. The use of a resistive heating blanket (RHB) is a common but costly approach to patient warming. We have introduced the use of a heat-band in our centre as a cost-effective alternative to the RHB for patient warming. The efficacy of the heat-band in preventing IPH during laparotomy for gynaecological surgeries was compared with that of the RHB.

Matched MeSH terms: Heating
Fulltext Oxidation and Polymerization of Triacylglycerols: In-Depth Investigations towards the Impact of Heating Profiles

Khor YP, Hew KS, Abas F, Lai OM, Cheong LZ, Nehdi IA, et al.

Foods, 2019 Oct 11;8(10).
PMID: 31614487 DOI: 10.3390/foods8100475

The stability of refined, bleached, and deodorized palm olein (RBDPO) was studied under controlled heating conditions. RBDPO was heated continuously for 24 h at 160, 170, and 180 °C, with oil sampled at four hour intervals. Thermo-oxidative alterations were measured through various parameters, such as monomeric oxidized triacylglycerols (oxTAG), total polar compounds (TPC), polymerized triacylglycerols (PTG), oxidative stability, and fatty acid composition. After 24 h of heating, the TPC and triacylglycerol oligomers showed a linear increase with heating time at all heating temperatures. At the end of the heating study, more epoxy acids were formed than keto and hydroxy acids. Moreover, caprylic acid, which was not present in fresh oil, was formed in significant amounts. The increase in oxTAG was strongly correlated with the increase in the p-anisidine value and total oxidation value. The decreases in diacylglycerol and free fatty acids were strongly correlated with an increase in PTG.

Matched MeSH terms: Heating
Optimizing palm oil and palm stearin utilization for sensory and textural properties of chicken frankfurters

Tan SS, Aminah A, Zhang XG, Abdul SB

Meat Sci, 2006 Mar;72(3):387-97.
PMID: 22061722 DOI: 10.1016/j.meatsci.2005.07.012

This study was designed to explore the potential of refined, bleached and deodorized (RBD) palm oil (PO) and palm stearin (POs) utilization in chicken frankfurters. A 10 points augmented simplex-centroid design was used to study the effect of chicken fat (CF), PO and POs as well as the interaction of these fats on the emulsion, textural and sensory properties of chicken frankfurters. All frankfurters were formulated to contain approx 25% fat, 52% moisture and 10% protein. No significant difference was found in end chopping temperatures of all meat batters even though the temperature of PO and POs upon incorporation into meat batters was 50°C higher than CF. Strong emulsions were formed as no fluid losses were observed in all the meat batters tested after heating. Texture profiles of the frankfurters containing PO and/or CF were quite similar, but increment of POs raised hardness, chewiness, and shear hardness of the frankfurters. Acceptability of the frankfurters was evaluated using hedonic test. Panelists found no difference in hardness preference between frankfurters made from totally CF and PO, while frankfurters made from POs were rated as hard and brittle. CF was important in determining acceptability of the frankfurters, as reduction of CF in formulation resulted in lower scores in chicken flavor, juiciness, oiliness and overall acceptance of the frankfurters. Frankfurters with sensory acceptability comparable to a commercial one were found to comprise of more than 17% CF, and less than 67% PO and 17% POs of the fat blend.

Matched MeSH terms: Heating
Optimization of palm oil mill sludge biochar preparation for sulfur dioxide removal

Iberahim N, Sethupathi S, Bashir MJK

Environ Sci Pollut Res Int, 2018 Sep;25(26):25702-25714.
PMID: 28550632 DOI: 10.1007/s11356-017-9180-5

In this study, palm oil mill sludge was used as a precursor to prepare biochar using conventional pyrolysis. Palm oil mill sludge biochar (POSB) was prepared at different preparation variables, i.e., heating temperature (300-800 °C), heating rate (10-20 °C/min) and holding time (60-120 min). The prepared biochars were tested for sulfur dioxide (SO2) adsorption in a fixed bed reactor using 300 ppm of SO2 gas at 300 ml/min (with N2 gas as balance). Response surface central composite experimental design was used to optimize the production of biochar versus SO2 removal. A quadratic model was developed in order to correlate the effect of variable parameters on the optimum adsorption capacity of SO2 gas. The experimental values and the predicted results of the model were found to show satisfactory agreement. The optimum conditions for biochar preparation to yield the best SO2 removal was found to be at 405 °C of heating temperature, 20 °C/min of heating rate and 88 min of holding time. At these conditions, the average yield of biochar and adsorption capacity for SO2 gas was reported as 54.25 g and 9.75 mg/g, respectively. The structure of biochar and their roles in SO2 adsorption were investigated by surface area, morphology images, infrared spectra, and proximate analysis, respectively. The characterization findings suggested that POSB adsorbs SO2 mainly by the functional groups.

Matched MeSH terms: Heating
Optimization and characterization of bio-oil produced by microwave assisted pyrolysis of oil palm shell waste biomass with microwave absorber

Mushtaq F, Abdullah TA, Mat R, Ani FN

Bioresour Technol, 2015 Aug;190:442-50.
PMID: 25794811 DOI: 10.1016/j.biortech.2015.02.055

In this study, solid oil palm shell (OPS) waste biomass was subjected to microwave pyrolysis conditions with uniformly distributed coconut activated carbon (CAC) microwave absorber. The effects of CAC loading (wt%), microwave power (W) and N2 flow rate (LPM) were investigated on heating profile, bio-oil yield and its composition. Response surface methodology based on central composite design was used to study the significance of process parameters on bio-oil yield. The coefficient of determination (R(2)) for the bio-oil yield is 0.89017 indicating 89.017% of data variability is accounted to the model. The largest effect on bio-oil yield is from linear and quadratic terms of N2 flow rate. The phenol content in bio-oil is 32.24-58.09% GC-MS area. The bio-oil also contain 1,1-dimethyl hydrazine of 10.54-21.20% GC-MS area. The presence of phenol and 1,1-dimethyl hydrazine implies that the microwave pyrolysis of OPS with carbon absorber has the potential to produce valuable fuel products.

Matched MeSH terms: Heating/methods*
Fulltext On the Utilization of Pozzolanic Wastes as an Alternative Resource of Cement

Karim MR, Hossain MM, Khan MNN, Zain MFM, Jamil M, Lai FC

Materials (Basel), 2014 Dec 05;7(12):7809-7827.
PMID: 28788277 DOI: 10.3390/ma7127809

Recently, as a supplement of cement, the utilization of pozzolanic materials in cement and concrete manufacturing has increased significantly. This study investigates the scope to use pozzolanic wastes (slag, palm oil fuel ash and rice husk ash) as an alkali activated binder (AAB) that can be used as an alternative to cement. To activate these materials, sodium hydroxide solution was used at 1.0, 2.5 and 5.0 molar concentration added into the mortar, separately. The required solution was used to maintain the flow of mortar at 110% ± 5%. The consistency and setting time of the AAB-paste were determined. Mortar was tested for its flow, compressive strength, porosity, water absorption and thermal resistance (heating at 700 °C) and investigated by scanning electron microscopy. The experimental results reveal that AAB-mortar exhibits less flow than that of ordinary Portland cement (OPC). Surprisingly, AAB-mortars (with 2.5 molar solution) achieved a compressive strength of 34.3 MPa at 28 days, while OPC shows that of 43.9 MPa under the same conditions. Although water absorption and porosity of the AAB-mortar are slightly high, it shows excellent thermal resistance compared to OPC. Therefore, based on the test results, it can be concluded that in the presence of a chemical activator, the aforementioned pozzolans can be used as an alternative material for cement.

Matched MeSH terms: Heating
Fulltext Oil Palm Waste-Based Precursors as a Renewable and Economical Carbon Sources for the Preparation of Reduced Graphene Oxide from Graphene Oxide

Nasir S, Hussein MZ, Yusof NA, Zainal Z

Nanomaterials (Basel), 2017 Jul 13;7(7).
PMID: 28703757 DOI: 10.3390/nano7070182

Herein, a new approach was proposed to produce reduced graphene oxide (rGO) from graphene oxide (GO) using various oil palm wastes: oil palm leaves (OPL), palm kernel shells (PKS) and empty fruit bunches (EFB). The effect of heating temperature on the formation of graphitic carbon and the yield was examined prior to the GO and rGO synthesis. Carbonization of the starting materials was conducted in a furnace under nitrogen gas for 3 h at temperatures ranging from 400 to 900 °C and a constant heating rate of 10 °C/min. The GO was further synthesized from the as-carbonized materials using the 'improved synthesis of graphene oxide' method. Subsequently, the GO was reduced by low-temperature annealing reduction at 300 °C in a furnace under nitrogen gas for 1 h. The IG/ID ratio calculated from the Raman study increases with the increasing of the degree of the graphitization in the order of rGO from oil palm leaves (rGOOPL) < rGO palm kernel shells (rGOPKS) < rGO commercial graphite (rGOCG) < rGO empty fruit bunches (rGOEFB) with the IG/ID values of 1.06, 1.14, 1.16 and 1.20, respectively. The surface area and pore volume analyses of the as-prepared materials were performed using the Brunauer Emmett Teller-Nitrogen (BET-N₂) adsorption-desorption isotherms method. The lower BET surface area of 8 and 15 m2 g-1 observed for rGOCG and rGOOPL, respectively could be due to partial restacking of GO layers and locally-blocked pores. Relatively, this lower BET surface area is inconsequential when compared to rGOPKS and rGOEFB, which have a surface area of 114 and 117 m² g-1, respectively.

Matched MeSH terms: Heating
Fulltext Offretite Zeolite Single Crystals Synthesized by Amphiphile-Templating Approach

Ng EP, Ahmad NH, Khoerunnisa F, Mintova S, Ling TC, Daou TJ

Molecules, 2021 Apr 13;26(8).
PMID: 33924655 DOI: 10.3390/molecules26082238

Offretite zeolite synthesis in the presence of cetyltrimethylammonium bromide (CTABr) is reported. The offretite crystals were synthesized with a high crystallinity and hexagonal prismatic shape after only 72 h of hydrothermal treatment at 180 °C. The CTABr has dual-functions during the crystallization of offretite, viz. as structure-directing agent and as mesoporogen. The resulting offretite crystals, with a Si/Al ratio of 4.1, possess more acid sites than the conventional offretite due to their high crystallinity and hierarchical structure. The synthesized offretite is also more reactive than its conventional counterpart in the acylation of 2-methylfuran for biofuel production under non-microwave instant heating condition, giving 83.5% conversion with 100% selectivity to the desired product 2-acetyl-5-methylfuran. Hence, this amphiphile synthesis approach offers another cost-effective and alternative route for crystallizing zeolite materials that require expensive organic templates.

Matched MeSH terms: Heating
Nitridation of Al-Mg-Si alloys through dynamic heating

Roslinda Shamsudin, Abdul Razak Daud, Muhammad Azmi Abdul Hamid, Saiful Rizam Shamsudin

Sains Malaysiana, 2007;36:195-200.

Nitridation behaviour of Al-Mg-Si alloys was studied as a function of temperature by means of thermogravimetry method. A reactive gas, N2-4%H2 at a rate of 10 ml/min was purged into the thermogravimetry analyser chamber. The Al alloys were heated from 25oC to 625oC at the heating rate of 15oC/min and then reduced to 3oC/min until it reached 1500oC. It was found that by varying the amount of Mg and Si in Al-Mg-Si alloys significantly influenced the growth of the composites. A differential thermogravimetric curve shows the Mg containing alloys experienced many steps of chemical reactions. This indicates that besides AlN presence as a major phase, other compounds also exist in the final product. The X-ray diffraction results confirmed the existence of oxide phases such as a-Al2O3, MgAl2O4 and MgO in addition to residual Si and Al metal. The presence of oxide compounds is believed to be due to the reaction between the alloying elements and residual oxygen gas left in the reaction atmosphere. It was also found that Si could play a role in promoting the weight gain of the composite produced. The heating rate has also a profound effect on the weight gain, whereby higher heating rate resulted in low yielded of AlN during the nitridation reaction of the Al-Mg-Si alloys.

Matched MeSH terms: Heating
New crown-shaped polyoxovanadium(V) cluster cation with a mu(6)-sulfato anion and zwitterionic mu-(beta-alanine): crystal structure of [V(6)O(12)(OH)(3)(O(2)CCH(2)CH(2)NH(3))(3)(SO(4))][Na][SO(4)].13H(2)O

Ng CH, Lim CW, Teoh SG, Fun HK, Usman A, Ng SW

Inorg Chem, 2002 Jan 14;41(1):2-3.
PMID: 11782136

Treatment of vanadium(V) oxide with an ethanol-concentrated sulfuric acid mixture, followed by the addition of an equimolar amount of beta-alanine and sodium hydroxide, and finally raising the pH to 3.9 with sodium carbonate solution, under continuous heating in a water bath and in the presence of air, leads to the polyionic sodium cyclo-[mu(6)-(sulfato-O,O',O'')tris[mu-(beta-alanine-O,O')-mu-oxo]tris(mu-hydroxo-mu-oxo)hexa[oxovanadium(V)]] sulfate tridecahydrate which crystallizes in the monoclinic P2(1)/n space group [a = 9.5192(4), b = 20.1185(9), c = 22.6174(9) A, beta = 97.011(1) degrees; Z = 4]. The crown-shaped polyoxovanadium(V) cluster cation, with carboxylate-bridging amino acid ligands, has an Anderson structure with two unique capping sulfato ligands. Its structural analysis, together with IR, UV-vis, and preliminary data on its solution properties, is presented.

Matched MeSH terms: Heating
Nanostructured SnO2-Ge Multi-layer thin Films with Quantum Confinement Effects for Solar Cell

Khan AF, Sajjad W, Rahim NA

Recent Pat Nanotechnol, 2016;10(1):77-82.
PMID: 27018275

BACKGROUND: It is well-known that multi-layer films with nanostructure can give novel properties by interfacial phenomenon and quantum confinement effects. Nanostructured multi-layer thin films are presently being analyzed for their vast applications in the area of optoelectronics technology particularly photovoltaics. Hereof, two dimensional thin films with nanostructure are of prime importance due to their structure dependent optical, electrical, and opto-electronic properties. It has been revealed that these films exhibit quantum confinement effects with band gap engineering. The main focus of the research is to evaluate the effect on structural and optical properties with number of layers.
METHODS: Nanostructured SnO2-Ge multi-layer thin films were fabricated using electron beam evaporation and resistive heating techniques. Alternate layers of SnO2 and Ge were deposited on glass substrate at a substrate temperature of 300 °C in order to obtain uniform and homogeneous deposition. The substrate temperature of 300 °C has been determined to be effective for the deposition of these multi-layer films from our previous studies. The films were characterized by investigating their structural and optical properties. The structural properties of the as-deposited films were characterized by Rutherford Backscattering Spectroscopy (RBS) and Raman spectroscopy and optical properties by Ultra-Violet-Near infrared (UV-VIS-NIR) spectroscopy.
RESULTS: RBS studies confirmed that the layer structure has been effectively formed. Raman spectroscopy results show that the peaks of both Ge and SnO2 shifts towards lower wavenumbers (in comparison with bulk Ge and SnO2, suggesting that the films consist of nanostructures and demonstrate quantum confinement effects. UV-VIS-NIR spectroscopy showed an increase in the band gap energy of Ge and SnO2 and shifting of transmittance curves toward higher wavelength by increasing the number of layers. The band gap lies in the range of 0.9 to 1.2 eV for Ge, while for SnO2, it lies between 1.7 to 2.1 eV.
CONCLUSION: Analysis of results suggests that the nanostructured SnO2-Ge multi-layer thin film can work as heterojunction materials with quantum confinement effects. Accordingly, the present SnO2-Ge multi-layer films may be employed for photovoltaic applications. Few relevant patents to the topic have been reviewed and cited.

Matched MeSH terms: Heating
Fulltext Nanocellulose Reinforced Thermoplastic Starch (TPS), Polylactic Acid (PLA), and Polybutylene Succinate (PBS) for Food Packaging Applications

Nazrin A, Sapuan SM, Zuhri MYM, Ilyas RA, Syafiq R, Sherwani SFK

Front Chem, 2020;8:213.
PMID: 32351928 DOI: 10.3389/fchem.2020.00213

Synthetic plastics are severely detrimental to the environment because non-biodegradable plastics do not degrade for hundreds of years. Nowadays, these plastics are very commonly used for food packaging. To overcome this problem, food packaging materials should be substituted with "green" or environmentally friendly materials, normally in the form of natural fiber reinforced biopolymer composites. Thermoplastic starch (TPS), polylactic acid (PLA) and polybutylene succinate (PBS) were chosen for the substitution, because of their availability, biodegradability, and good food contact properties. Plasticizer (glycerol) was used to modify the starch, such as TPS under a heating condition, which improved its processability. TPS films are sensitive to moisture and their mechanical properties are generally not suitable for food packaging if used alone, while PLA and PBS have a low oxygen barrier but good mechanical properties and processability. In general, TPS, PLA, and PBS need to be modified for food packaging requirements. Natural fibers are often incorporated as reinforcements into TPS, PLA, and PBS to overcome their weaknesses. Natural fibers are normally used in the form of fibers, fillers, celluloses, and nanocelluloses, but the focus of this paper is on nanocellulose. Nanocellulose reinforced polymer composites demonstrate an improvement in mechanical, barrier, and thermal properties. The addition of compatibilizer as a coupling agent promotes a fine dispersion of nanocelluloses in polymer. Additionally, nanocellulose and TPS are also mixed with PLA and PBS because they are costly, despite having commendable properties. Starch and natural fibers are utilized as fillers because they are abundant, cheap and biodegradable.

Matched MeSH terms: Heating

Filters

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links