Displaying publications 1 - 20 of 424 in total

Abstract:
Sort:
  1. Kesan lapisan berliang dan nisbah keluasan plat berlubang terhadap ciri akustik serabut sabut kelapa sebagai bahan penyerap bunyi
    Zulkarnain, Rozli Zulkifli, Mohd Jailani Mohd Nor
    Sains Malaysiana, 2011;40:1179-1186.
    Penyelidikan ini dilakukan untuk mengkaji ciri akustik serabut sabut kelapa yang berpotensi digunakan sebagai bahan penyerap bunyi. Untuk meningkatkan ciri akustik serabut sabut kelapa pada frekuensi rendah, lapisan berliang digunakan di bahagian depan atau belakang bertujuan untuk meningkatkan nilai galangan permukaan. Bahan selanjutnya dilapisi dengan plat berlubang dengan nisbah keluasan yang berbeza. Sampel diuji mengikut piawaian antarabangsa ASTM E 1050-98 untuk menentukan pekali penyerapan bunyi. Daripada hasil uji kaji, plat 1 mm berlubang yang diperbuat daripada kepingan aluminium yang melapisi serabut sabut kelapa, didapati bahawa nilai maksimum pekali penyerapan bunyi berada pada frekuensi antara 2750 Hz hingga 2825 Hz iaitu dengan nilai 0.97. Nilai nisbah keluasan plat berlubang memberikan pengaruh penurunan pekali penyerapan bunyi pada frekuensi tinggi. Penurunan nilai pekali penyerapan bunyi terjadi apabila plat berlubang mempunyai nilai nisbah keluasan di bawah 0.22. Akan tetapi, penggunaan plat berlubang boleh meningkatkan prestasi penyerapan bunyi serabut sabut kelapa pada frekuensi rendah. Kesepakatan yang baik diperoleh daripada keputusan uji kaji dan analisis dengan pendekatan rangkaian elektrik setara yang digunakan untuk menghitung nilai pekali penyerapan bunyi. Ini menunjukkan bahawa pendekatan rangkaian elektrik setara boleh digunakan untuk merancang dan mengoptimumkan ciri akustik serabut sabut sebagai bahan penyerap bunyi.
    Matched MeSH terms: Aluminum
  2. Penggunaan jaringan neural tiruan untuk analisis kuantitatif ion Al (III) berasaskan pengecaman corak spektrum serapan
    Tan LL, Musa Ahmad
    Sains Malaysiana, 2008;37.
    Analisis kuantitatif telah dilakukan untuk menentukan kepekatan ion aluminium (Al3+) dalam larutan dengan menggunakan kaedah spektrofotometri UL-Nampak dan jaringan neural tiruan (ANN). Reagen morin telah digunakan untuk membentuk kompleks morin-Al(III). Pencirian terhadap reagen dalam larutan termasuk analisis kestabilan foto reagen, kesan pH, kesan kepekatan, masa rangsangan, julat kepekatan dinamik dan kebolehulangan telah dilakukan. Penggunaan ANN telah berupaya memanjangkan julat kepekatan dinamik ion Al3+ sehingga julat kepekatan 1-13 ppm.
    Matched MeSH terms: Aluminum
  3. Pencirian keseragaman campuran dan sifat reologi serbuk alumina-zirkonia untuk pengacuan suntikan seramik
    Sarizal Md Ani, Andanastuti Muchtar, Norhamidi Muhamad, Jaharah A. Ghani
    Sains Malaysiana, 2013;42:1311-1317.
    Pencirian keseragaman campuran dan sifat reologi bahan suapan merupakan elemen penting dalam melaksanakan proses pengacuan suntikan seramik. Kesesuaian bahan suapan yang dibangunkan dapat mengurangkan masalah yang timbul ketika proses pengacuan suntikan, penyahikatan dan pensinteran. Justeru itu, kajian ini dijalankan untuk mengenal pasti pembebanan serbuk yang optimum berdasarkan kepada keseragaman campuran dan sifat reologi bahan. Pencirian keseragaman campuran ditentukan berdasarkan kepada nilai tork yang rendah dan berkeadaan mantap. Kajian reologi pula dilakukan dengan menggunakan mesin reometer rerambut. Ujian dijalankan pada julat suhu 150 dan 170oC dengan beban kenaan antara 20 dan 90 kgf. Bahan suapan yang digunakan terdiri daripada kombinasi serbuk seramik alumina-zirkonia bersama bahan pengikat polietilena berketumpatan tinggi, lilin parafin dan asid stearik. Hasil kajian menunjukkan bahan suapan bersifat pseudoplastik dengan pencampuran bahan yang seragam dalam tempoh kurang daripada 30 min. Hasil keputusan juga mendapati pada pembebanan serbuk 57% isi padu adalah yang paling optimum untuk proses pengacuan suntikan seramik berdasarkan kepada nilai kelikatan, indeks hukum kuasa dan tenaga pengaktifan aliran yang rendah.
    Matched MeSH terms: Aluminum Oxide
  4. Fulltext Development of Magnesium Aluminate (MgAl2O4) Nanoparticles for refractory crucible application
    Khan SA, Mohd Zain Z, Siddiqui Z, Khan W, Aabid A, Baig M, et al.
    PLoS One, 2024;19(1):e0296793.
    PMID: 38227597 DOI: 10.1371/journal.pone.0296793
    Ceramics are the oxides of metals and nonmetals with excellent compressive strength. Ceramics usually exhibit inert behavior at high temperatures. Magnesium aluminate (MgAl2O4), a member of the ceramic family, possesses a high working temperature up to 2000°C, low thermal conductivity, high strength even at elevated temperatures, and good corrosion resistance. Moreover, Magnesium Aluminate Nanoparticles (MANPs) can be used in the making of refractory crucible applications. This study focuses on the thermal behavior of Magnesium Aluminate Nanoparticles (MANPs) and their application in the making of refractory crucibles. The molten salt method is used to obtain MANPs. The presence of MANPs is seen by XRD peaks ranging from 66° to 67°. The determination of the smallest crystallite size of the sample is achieved by utilizing the Scherrer formula and is found to be 15.3 nm. The SEM micrographs provided further information, indicating an average particle size of 91.2 nm. At 600°C, DSC curves show that only 0.05 W/g heat flows into the material, and the TGA curve shows only 3% weight loss, which is prominent for thermal insulation applications. To investigate the thermal properties, crucibles of pure MANPs and the different compositions of MANPs and pure alumina are prepared. During the sintering, cracks appear on the crucible of pure magnesium aluminate. To explore the reason for crack development, tablets of MgAl2O4 are made and sintered at 1150°C. Ceramography shows the crack-free surfaces of all the tablets. Results confirm the thermal stability of MANPs at high temperatures and their suitability for melting crucible applications.
    Matched MeSH terms: Aluminum Oxide*; Aluminum Compounds*
  5. Kinetics of aluminium removal by locally isolated Brochothrix thermosphacta and Vibrio alginolyticus
    Titah HS, Purwanti IF, Tangahu BV, Kurniawan SB, Imron MF, Abdullah SRS, et al.
    J Environ Manage, 2019 May 15;238:194-200.
    PMID: 30851558 DOI: 10.1016/j.jenvman.2019.03.011
    The emergence of the aluminium recycling industry has led to an increase in aluminium-containing wastewater discharge to the environment. Biological treatment of metal is one of the solutions that can be provided as green technology. Screening tests showed that Brochothrix thermosphacta and Vibrio alginolyticus have the potential to remove aluminium from wastewater. Brochothrix thermosphacta removed up to 49.60%, while Vibrio alginolyticus was capable of removing up to 59.72% of 100 mg/L aluminium in acidic conditions. The removal of aluminium by V. alginolyticus was well fitted with pseudo-first-order kinetics (k1 = 0.01796/min), while B. thermosphacta showed pseudo-second-order kinetics (k2 = 0.125612 mg substrate/g adsorbent. hr) in the process of aluminium removal. V. alginolyticus had a higher rate constant under acidic conditions, while B. thermosphacta had a higher rate constant under neutral pH conditions.
    Matched MeSH terms: Aluminum*
  6. Aluminum Microcomb Electrodes on Silicon Wafer for Detecting Val66Met Polymorphism in Brain-Derived Neurotrophic Factor
    Li Z, Cui L, Zhao H, Du J, Gopinath SCB, Lakshmipriya T, et al.
    Dev Neurosci, 2021;43(1):53-62.
    PMID: 33849012 DOI: 10.1159/000515197
    OBJECTIVE: Brain-derived neurotrophic factor (BDNF) dysregulation is widely related with various psychiatric and neurological disorders, including schizophrenia, depression, Rett syndrome, and addiction, and the available evidence suggests that BDNF is also highly correlated with Parkinson's and Alzheimer's diseases.

    METHODS: The BDNF target sequence was detected on a capture probe attached on aluminum microcomb electrodes on the silicon wafer surface. A capture-target-reporter sandwich-type assay was performed to enhance the detection of the BDNF target.

    RESULTS: The limit of detection was noticed to be 100 aM. Input of a reporter sequence at concentrations >10 aM improved the detection of the target sequence by enhancing changes in the generated currents. Control experiments with noncomplementary and single- and triple-mismatches of target and reporter sequences did not elicit changes in current levels, indicating the selective detection of the BDNF gene sequence.

    CONCLUSION: The above detection strategy will be useful for the detection and quantification of BDNF, thereby aiding in the provision of suitable treatments for BDNF-related disorders.

    Matched MeSH terms: Aluminum*
  7. An investigation on the relationship between physicochemical characteristics of alumina-supported cobalt catalyst and its performance in dry reforming of methane
    Khairudin NF, Mohammadi M, Mohamed AR
    Environ Sci Pollut Res Int, 2021 Jun;28(23):29157-29176.
    PMID: 33550559 DOI: 10.1007/s11356-021-12794-0
    This study deals with the development of alumina-supported cobalt (Co/Al2O3) catalysts with remarkable performance in dry reforming of methane (DRM) and least carbon deposition. The influence of Co content, calcination, and reduction temperatures on the physicochemical attributes and catalyst activity of the developed catalysts was extensively studied. For this purpose, several characterization techniques including ICP-MS, H2 pulse chemisorption, HRTEM, H2-TPR, N2 adsorption desorption, and TGA were implemented, and the properties of the developed catalysts were carefully analyzed. The impact of reaction temperature, feed gas ratio, and gas hourly space velocity (GHSV) on the reactants conversion and products yield was investigated. Use of 10%Co/Al2O3 catalyst, calcined at 500°C and reduced under H2 at 900°C in DRM reaction at 850°C, CH4/CO2 ratio of 1:1, and GHSV of 6 L.g-1.h-1 resulted in a remarkable catalytic activity and sustainable performance in long-term operation where great CO2 (96%) and CH4 (98%) conversions and high H2 (83%) and CO (91%) yields with a negligible carbon deposition (3 wt%) were attained in 100-h on-stream reaction. The good performance of the developed catalyst in DRM reaction was attributed to the small Co particle size with well-dispersion on the alumina support which increased the catalytic activity and also the strong metal-support interaction which inhibited any serious metal sintering and enhanced the catalyst stability.
    Matched MeSH terms: Aluminum Oxide*
  8. Effects of Bauxite and Alumina Exposure on Incidence of Cancer - Meta-analysis
    Thevi T, Abas AL
    Kathmandu Univ Med J (KUMJ), 2021 6 25;18(72):414-419.
    PMID: 34165102
    Bauxite is an ore from which Aluminium is produced. Malaysia, once the leading producer of bauxite has reduced production as mining activity has caused community outrage. Due to concerns about health concerns, rising pollution and environmental hazards, the government has revoked the licenses of bauxite miners. We therefore did a meta-analysis to assess the relationship between exposure to Bauxite and Alumina with incidence of various types of cancers. Bauxite mines and alumina refineries. Individuals of all ages exposed to Bauxite and Alumina. Exposure to bauxite and alumina. Incidence due to overall cancers and specific types of cancers. Exposure to bauxite and alumina did not cause variations in incidence of overall cancer and specific types of cancer such as cancer of lip, cancer of the oral cavity and pharynx, cancer of digestive organs and others. We conclude that there is no evidence that bauxite or alumina exposure cause increase incidence of cancer but due to the small number of studies included in this review, we recommend more cohort studies to be done in future.
    Matched MeSH terms: Aluminum Oxide/adverse effects; Aluminum Oxide/analysis
  9. Fulltext Phase transformations of α-alumina made from waste aluminum via a precipitation technique
    Matori KA, Wah LC, Hashim M, Ismail I, Zaid MH
    Int J Mol Sci, 2012;13(12):16812-21.
    PMID: 23222685 DOI: 10.3390/ijms131216812
    We report on a recycling project in which α-Al(2)O(3) was produced from aluminum cans because no such work has been reported in literature. Heated aluminum cans were mixed with 8.0 M of H(2)SO(4) solution to form an Al(2)(SO(4))(3) solution. The Al(2)(SO(4))(3) salt was contained in a white semi-liquid solution with excess H(2)SO(4); some unreacted aluminum pieces were also present. The solution was filtered and mixed with ethanol in a ratio of 2:3, to form a white solid of Al(2)(SO(4))(3)·18H(2)O. The Al(2)(SO(4))(3)·18H(2)O was calcined in an electrical furnace for 3 h at temperatures of 400-1400 °C. The heating and cooling rates were 10 °C /min. XRD was used to investigate the phase changes at different temperatures and XRF was used to determine the elemental composition in the alumina produced. A series of different alumina compositions, made by repeated dehydration and desulfonation of the Al(2)(SO(4))(3)·18H(2)O, is reported. All transitional alumina phases produced at low temperatures were converted to α-Al(2)O(3) at high temperatures. The X-ray diffraction results indicated that the α-Al(2)O(3) phase was realized when the calcination temperature was at 1200 °C or higher.
    Matched MeSH terms: Aluminum/chemistry*; Aluminum Oxide/chemistry*
  10. Kesan suhu celupan ke atas mikrostruktur dan kekerasan salutan aluminium pada keluli karbon
    Azman Jalar, Norinsan Kamil Othman, Emee Marina Salleh, Zaifol Samsu
    Sains Malaysiana, 2018;47:1251-1257.
    Keluli karbon amat mudah terkakis dalam pelbagai persekitaran terutamanya dalam keadaan berudara lembap dan suhu tinggi. Oleh sebab itu, permukaan keluli karbon perlu dilindungi dengan bahan atau logam yang mampu menangani serangan kakisan yang agresif dengan membentuk lapisan oksida dan lapisan antara logam yang bersifat pelindung. Kajian ini dijalankan untuk menentukan mikrostruktur permukaan dan kekerasan salutan aluminium (Al) tulen yang telah dihasilkan melalui teknik celupan panas. Celupan panas dalam leburan Al tulen dilakukan pada suhu berbeza untuk mendapatkan lapisan salutan yang optimum. Keputusan teknik celupan panas menunjukkan dua lapisan utama terhasil iaitu lapisan luar Al dan lapisan dalam aluminit (Fe-Al). Manakala lapisan dalam aluminida terdiri daripada dua lapisan yang berbeza iaitu lapisan nipis luar FeAl3 dan lapisan tebal dalam Fe2Al5. Keputusan daripada ujian mikrokekerasan Vickers menunjukkan bahawa nilai kekerasan lapisan aluminida meningkat dengan peningkatan suhu leburan Al manakala lapisan Al tidak menunjukkan sebarang perubahan yang ketara.
    Matched MeSH terms: Aluminum
  11. Synthesis and characterization of mesoporous molybdenum catalysts for hydrocracking of atmospheric residual oil
    Looi PY, Mohamed AR, Tye CT
    J Nanosci Nanotechnol, 2013 Oct;13(10):6988-95.
    PMID: 24245175
    In this study, performances of mesoporous Mo/Al2O3 catalysts prepared by sol-gel and post-hydrolysis methods in hydrocracking of atmospheric residual oil were compared. In addition, different methods: (i) the single step and (ii) conventional impregnation method to incorporate active metal over the mesoporous support were also investigated. For single step method, Mo/Al2O3 catalysts were synthesized directly by sol-gel and post-hydrolysis method. On the other hand, the impregnation method was a two step procedure which involved the production of alumina via sol-gel or post-hydrolysis method and followed by respective Mo impregnation. In general, mesoporous Mo/Al2O3 catalysts prepared by sol-gel method resulted in relatively higher surface area (> 400 m2/g) and large pore volume (- 0.8 cm3/g). Mo/Al2O3 catalysts prepared by sol-gel method exhibited higher hydrocracking activity as well. The Mo crystal size was found to relate directly with the hydrocracking result.
    Matched MeSH terms: Aluminum Oxide
  12. Fulltext Characterisation of lateral and vertical subsurface heterogeneity in the ground using sustainable seismic surface wave methodology
    Madun, A., Wijeyesekera, D.C., Ahmad Tajuddin, S.A., Zainalabidin, M.H., Yunus, R., Baharudin, M.F.
    Pertanika Journal of Science & Technology, 2017;25(105):169-176.
    MyJurnal
    Seismic surface waves are a non-destructive technique used to obtain the dynamic properties of soil by measuring the shear wave velocity and calculating the shear modulus of soil. The shear modulus is one of the parameters to measure the stiffness of materials. This study evaluates soil profiles and the position of the sensor while conducting measurements of two , soil profiles, i.e. lateral and vertical non-homogeneities, using a continuous surface wave analysis (CSW) and multi-channel analysis of surface waves (MASW). Results showed the dispersive curve demonstrated an increased shear wave velocity with increasing depth for the sensor pair measurements on the clay (between columns), and decreased shear wave velocity with increasing depth for the sensor pair measurements on the column. In both instances the surface wave velocity results influenced by the depth and size of the wavelength, indicating that depth and wavelength controlled the volume of measurement in an elliptical shape. Therefore, the shear wave velocities and thus stiffness measured from the surface wave velocity techniques are represented the volume of soil measured across the sensor length.
    Matched MeSH terms: Aluminum Silicates
  13. Fulltext Preliminary survey on potential slope instability and soil physico-chemical characteristic in Cameron Highlands, Pahang. (Tinjauan awal potensi ketidakstabilan cerun dan cirian fiziko-kimia tanah di Cameron Highlands, Pahang)
    Zulfahmi Ali Rahman, Sahibin Abd. Rahim, Wan Muhd Razi Idris, Jasni Yaakob
    Sains Malaysiana, 2007;36(2):105-116.
    Secara geologi, kawasan Cameron Highland terdiri daripada batuan granit batolit yang merejah ke dalam batuan sedimen yang lebih tua. Rejahan jasad igneus asidik ini menyebabkan pembentukan batuan meta-sedimen dan batuan metamorfik lain sebagai sisa bumbung. Sekis sering ditemui telah mengalami luluhawa tinggi hingga sepenuhnya, berwarna kelabu cerah hingga gelap dengan butiran halus hingga sederhana dan struktur foliasi yang ketara. Manakala batuan granit mengandungi mineral kuarza, felspar dan butiran biotit dan/atau turmalin. Kebanyakan cerun potongan jalan raya yang dibina merentasi jasad batuan ini dan survei ketidakstabilan cerun dilakukan berdasarkan jenis, geometri dan cirian fiziko-kimia tanah cerun. Hasil cerapan lapangan menunjukkan bahawa jenis cerun yang gagal adalah jenis cerun tanah yang terdiri daripada jenis gelinciran cetek dan dalam. Antara faktor yang menyumbang kepada ketidakstabilan cerun adalah geometri cerun seperti cerun yang tinggi dan sudut muka cerun yang curam, sifat keperoian tanah pada cerun dan kekurangan litupan vegetasi permukaan. Ini menyebabkan permukaan cerun terdedah kepada hentaman terus hujan. Kesan daripada air larian permukaan juga menyebabkan pembentukan alur-alur hakisan pada muka cerun tanah. Sifat fiziko-kimia bahan cerun (tanah) seperti taburan saiz partikel, pH, kandungan ferum oksida, bahan organik, kandungan air, ketumpatan pukal dan sebenar serta keporosan juga didapati memainkan peranan sebagai faktor yang dalaman dalam mempengaruhi kestabilan cerun tertentu yang dikaji. Julat pH tanah yang rendah (sifat asidik) pada semua cerun mengurangkan kandungan ferum oksida dalam tanah yang bertindak sebagai bahan penyimen tanah. Ini menyebabkan agregatan tanah menjadi lemah dan mudah terhakis.
    Matched MeSH terms: Aluminum Silicates
  14. Fulltext Influence of organic molecules on wetting characteristics of mica/H2/brine systems: Implications for hydrogen structural trapping capacities
    Ali M, Yekeen N, Pal N, Keshavarz A, Iglauer S, Hoteit H
    J Colloid Interface Sci, 2022 Feb 15;608(Pt 2):1739-1749.
    PMID: 34742087 DOI: 10.1016/j.jcis.2021.10.080
    HYPOTHESIS: Actualization of the hydrogen (H2) economy and decarbonization goals can be achieved with feasible large-scale H2 geo-storage. Geological formations are heterogeneous, and their wetting characteristics play a crucial role in the presence of H2, which controls the pore-scale distribution of the fluids and sealing capacities of caprocks. Organic acids are readily available in geo-storage formations in minute quantities, but they highly tend to increase the hydrophobicity of storage formations. However, there is a paucity of data on the effects of organic acid concentrations and types on the H2-wettability of caprock-representative minerals and their attendant structural trapping capacities.

    EXPERIMENT: Geological formations contain organic acids in minute concentrations, with the alkyl chain length ranging from C4 to C26. To fully understand the wetting characteristics of H2 in a natural geological picture, we aged mica mineral surfaces as a representative of the caprock in varying concentrations of organic molecules (with varying numbers of carbon atoms, lignoceric acid C24, lauric acid C12, and hexanoic acid C6) for 7 days. To comprehend the wettability of the mica/H2/brine system, we employed a contact-angle procedure similar to that in natural geo-storage environments (25, 15, and 0.1 MPa and 323 K).

    FINDINGS: At the highest investigated pressure (25 MPa) and the highest concentration of lignoceric acid (10-2 mol/L), the mica surface became completely H2 wet with advancing (θa= 106.2°) and receding (θr=97.3°) contact angles. The order of increasing θa and θr with increasing organic acid contaminations is as follows: lignoceric acid > lauric acid > hexanoic acid. The results suggest that H2 gas leakage through the caprock is possible in the presence of organic acids at higher physio-thermal conditions. The influence of organic contamination inherent at realistic geo-storage conditions should be considered to avoid the overprediction of structural trapping capacities and H2 containment security.

    Matched MeSH terms: Aluminum Silicates
  15. Rice husk ash based growing media impact on cucumber and melon growth and quality
    Li M, Ning XP, Gao TT, Fazry S, Othman BA, Najm AAK, et al.
    Sci Rep, 2024 Mar 01;14(1):5147.
    PMID: 38429352 DOI: 10.1038/s41598-024-55622-4
    Rice husk, an agricultural waste from the rice industry, can cause serious environmental pollution if not properly managed. However, rice husk ash (RHA) has been found to have many positive properties, making it a potential replacement for non-renewable peat in soilless planting. Thus, this study investigated the impact of a RHA composite substrate on the growth, photosynthetic parameters, and fruit quality of cucumber (Yuyi longxiang variety) and melon (Yutian yangjiaomi variety). The RHA, peat, vermiculite, and perlite were blended in varying proportions, with the conventional seedling substrate (peat:vermiculite:perlite = 1:1:1 volume ratio) serving as the control (CK). All plants were cultivated in barrels filled with 10L of the mixed substrates. The results from this study found that RHA 40 (RHA:peat:vermiculite:perlite = 4:4:1:1 volume ratio) significantly enhanced substrate ventilation and positively influenced the stem diameter, root activity, seedling index, chlorophyll content, net photosynthetic rate (Pn), stomatal conductance (Gs), and transpiration rate (Tr) of cucumber and melon plants. Additionally, plant planted using RHA 40, the individual fruit weight of cucumber and melon found to increase by 34.62% and 21.67%, respectively, as compared to the control. Aside from that, both cucumber and melon fruits had significantly higher sucrose, total soluble sugar, vitamin C, and soluble protein levels. This subsequently improved the activity of sucrose synthase and sucrose phosphate synthase in both cucumber and melon. In conclusion, the RHA 40 found to best promote cucumber and melon plant growth, increase plant leaf photosynthesis, and improve cucumber and melon fruit quality, making it a suitable substrate formula for cucumber and melon cultivation in place of peat.
    Matched MeSH terms: Aluminum Oxide*; Aluminum Silicates*
  16. Fulltext Enhancement of the wear resistance and microhardness of aluminum alloy by Nd:YaG laser treatment
    Hussein HT, Kadhim A, Al-Amiery AA, Kadhum AA, Mohamad AB
    ScientificWorldJournal, 2014;2014:842062.
    PMID: 25136694 DOI: 10.1155/2014/842062
    Influence of laser treatment on mechanical properties, wear resistance, and Vickers hardness of aluminum alloy was studied. The specimens were treated by using Nd:YaG laser of energy 780 mj, wavelength 512 nm, and duration time 8 ns. The wear behavior of the specimens was studied for all specimens before and after treatment by Nd:YaG laser and the dry wear experiments were carried out by sing pinon-disc technique. The specimens were machined as a disk with diameter of 25 mm and circular groove in depth of 3 mm. All specimens were conducted by scanning electron microscopy (SEM), energy-dispersive X-ray fluorescence analysis (EDS), optical microscopy, and Vickers hardness. The results showed that the dry wear rate was decreased after laser hardening and increased Vickers hardness values by ratio of 2.4:1. The results showed that the values of wear rate for samples having circular grooves are less than samples without grooves after laser treatment.
    Matched MeSH terms: Aluminum/chemistry*
  17. Fulltext DNA strand patterns on aluminium thin films
    Khatir NM, Banihashemian SM, Periasamy V, Majid WH, Rahman SA, Shahhosseini F
    Sensors (Basel), 2011;11(7):6719-27.
    PMID: 22163981 DOI: 10.3390/s110706719
    A new patterning method using Deoxyribose Nucleic Acid (DNA) strands capable of producing nanogaps of less than 100 nm is proposed and investigated in this work. DNA strands from Bosenbergia rotunda were used as the fundamental element in patterning DNA on thin films of aluminium (Al) metal without the need for any lithographic techniques. The DNA strands were applied in buffer solutions onto thin films of Al on silicon (Si) and the chemical interactions between the DNA strands and Al creates nanometer scale arbitrary patterning by direct transfer of the DNA strands onto the substrate. This simple and cost-effective method can be utilized in the fabrication of various components in electronic chips for microelectronics and Nano Electronic Mechanical System (NEMS) applications in general.
    Matched MeSH terms: Aluminum/chemistry*
  18. Fulltext Characterization of alumina using small angle neutron scattering (sans)
    Megat Harun Al Rashid Megat Ahmad, Abdul Aziz Mohamed, Azmi Ibrahim, Che Seman Mahmood, Putra, Edy Giri Rachman, Muhammad Rawi Muhammad Zin, et al.
    Journal of Nuclear and Related Technologies, 2007;2005(1):19-23.
    MyJurnal
    Alumina powder was synthesized from an aluminum precursor and studied using small angle neutron scattering (SANS) technique and complemented with transmission electron microscope (TEM). XRD measurement confirmed that the alumina produced was of high purity and highly crystalline D-phase. SANS examination indicates the formation of mass fractals microstructures with fractal dimension of about 2.8 on the alumina powder.
    Matched MeSH terms: Aluminum; Aluminum Oxide
  19. Fulltext Correlation between the bending strength and the thickness interlayer of alumina-mild steel friction welded at lower rotational speed
    Mohamad Zaky Noh, Luay Bakir Hussain, Zainal Arifin Ahmad
    Journal of Nuclear and Related Technologies, 2007;2007(1):75-82.
    MyJurnal
    The joining of ceramic-metal could be done through a few techniques: brazing, diffusion bonding, friction welding etc. However, the mechanism of ceramic-metal joining was still not properly understood. In this study, alumina rod was bonded to mild steel rod via friction welding technique by using Al 1100 sheet as interlayer. The diameter of the rods was 10 mm. Friction pressure of 20 MPa and forging pressure of 40 MPa were used. Rotational speeds were maintained at 900 rpm and friction times of 2 to 20 seconds were applied. The joining strength was determined through four point bending test. The maximum bending strength, 240 MPa was obtained at the friction times of 20 seconds. Under optical microscope and SEM observation, the deformation of the aluminum interface was clearly obtained. Mechanical interlocking and close contact between the aluminaaluminum and aluminum-mild steel were observed at magnifications of 3000X. The strength of alumina-steel bonding is much dependent on the wettability of the alumina surface by the molten aluminum and the existing of mechanical interlocking between interlayer and sample materials.
    Matched MeSH terms: Aluminum; Aluminum Oxide
  20. Kaolin pneumoconiosis
    CUMMINS GE, AUN YS, DAVIES TA
    Med J Malaya, 1958 Jun;12(4):613-7.
    PMID: 13577154
    Matched MeSH terms: Aluminum Silicates*
Related Terms
Filters
Contact Us

Please provide feedback to Administrator (afdal@afpm.org.my)

External Links